Manual Eizo SQ2801

59 pages 1.98 mb
Download

Go to site of 59

Summary
  • Eizo SQ2801 - page 1

    Important Please read PRECAUTIONS and this User’s Manual carefully to familiarize yourself with safe and effective usage procedure s. Please retain this manual for future reference. ...

  • Eizo SQ2801 - page 2

    ...

  • Eizo SQ2801 - page 3

    Copyright© 2007 T ech Source, Inc. Copyright© 2007 EIZO NANAO CORPORA TION No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwi se, without the prior written permissio n of T ech Source, Inc. and EIZO NANAO C ORPORA TION. T ech Source, Inc. and EIZO ...

  • Eizo SQ2801 - page 4

    Contents 1 Overview ....................................................................................................................... ........ 6 1.1 Layout of this Manual .......................................................................................................... ... 7 1.2 Warnings and Safety Notes .............................. ...

  • Eizo SQ2801 - page 5

    5 Technical Data ................................................................................................................. .. 54 5.1 Display Module ................................................................................................................. ... 54 5.2 Power Supply ........................................................ ...

  • Eizo SQ2801 - page 6

    1 Overview The TFT Monitor Raptor SQ2801 was developed to meet the very demanding requirements in the Air Traffic Management where system availability and reli ability is crucial. Ergonomic criteria have been addressed to ensure high acceptance from the operators. Reduced depth and lower weight compared to CRT monitors allow easy installation into ...

  • Eizo SQ2801 - page 7

    1.1 Layout of this Manual This manual was created to assist system integrat ors and operators during installa tion and operation of the LCD TFT Monitor Raptor SQ2801. The layout is intended to allow even inexperienced users to install and set-up the monitor. The manual is divided into following chapters: Chapter 1 Introduction Brief description of ...

  • Eizo SQ2801 - page 8

    1.2 Warnings and Safety Notes For information about warnings and safety notes, re fer to PRECATUIONS supplied with this manual. 8 1 Overview ...

  • Eizo SQ2801 - page 9

    1.3 Packaging NOTE To avoid permanent damage, great care should be taken to ensure that the monitor is adequately packed and transported in the correct manner. The original packaging should be retained and re-used for future transportation purposes. The original packaging has a red label with two arrows and text “hier oben” (see Fig. 1 and F ig ...

  • Eizo SQ2801 - page 10

    1.4 Instructions for Handling Com ponents Susceptible to Electrostatic Shocks Most of the assemblies within the LCD monitor Raptor SQ2801 contain components which can be permanently damaged or destroyed by electrostatic discharge. Such resulting damage may or may not result in total failure of the components or modules affected. The following preca ...

  • Eizo SQ2801 - page 11

    2 General Installation Preparation for installing the LCD monitor includes following steps: • Removal of all packaging materials • Checking of components for damage • Comparison of components received with those listed on the delivery note • Connection to the computer system and power supply • System integration under considerati on of te ...

  • Eizo SQ2801 - page 12

    2.2 Installing the Monitor The Raptor SQ2801 is currently offered in two versions - desktop version and chassis version. Both these version are discussed in this section. The desktop version is a “standalone” unit that can be placed on top of a desktop con sole. As for the chassis version, it is easy to integrate it onto t he rear of control pa ...

  • Eizo SQ2801 - page 13

    2.2.1 Raptor SQ2801 Dimensions (Chassis version) Fig. 3: Raptor SQ2801 Dimensions (Chassis version); Front View 2 General Installation 13 ...

  • Eizo SQ2801 - page 14

    Fig. 4: Raptor SQ2801 Dimensions (Chassis version); Rear View 14 2 General Installation ...

  • Eizo SQ2801 - page 15

    Fig. 5: Raptor SQ2801 Dimensions (Chassis version); Side View 2 General Installation 15 ...

  • Eizo SQ2801 - page 16

    2.2.2 Raptor SQ2801 Dimensions (Desktop version) Fig. 6: Raptor SQ2801 (Desktop Version); Front View 16 2 General Installation ...

  • Eizo SQ2801 - page 17

    Fig. 7: Raptor SQ2801 Dimensions (Desktop version); Rear View 2 General Installation 17 ...

  • Eizo SQ2801 - page 18

    Fig. 8: Raptor SQ2801 Dimensions (Desktop); Side View 18 2 General Installation ...

  • Eizo SQ2801 - page 19

    2.2.3 Raptor SQ2801 Dimensions (Panel mount version) Fig. 9: Raptor SQ2801 Dimensions (Panel mount); Front View 2 General Installation 19 ...

  • Eizo SQ2801 - page 20

    Fig. 10: Raptor SQ2801 Dimensions (Panel mount); Side View 20 2 General Installation ...

  • Eizo SQ2801 - page 21

    Fig. 11: Raptor SQ2801 Dimensions (Panel mount); Back View 2 General Installation 21 ...

  • Eizo SQ2801 - page 22

    2.3 Interfaces and Connector Assignment The monitor has been tested and pre-adjusted at the factor y. For system installation, connect the unit to the main power supply, serial interfaces an d input sources. All input connectors are shown in the figure below. All connections should adhere to EMC regulations. Use cord grips to secure cables. Fig. 12 ...

  • Eizo SQ2801 - page 23

    2.3.1 Analog RGB – Interface The analog RGB input may be used for Sony DDM comp atible configurations. However, the Raptor SQ2801 panel can also handle all common VESA timings. When using this interface, specific adjustments for phase and frequency may be necessary. These adjustments are explained in detail in section 3.3 on page 41. For connecti ...

  • Eizo SQ2801 - page 24

    2.3.2 DVI-1 / DVI-2 Interface The digital video inputs use the stan dard dual-link DVI interface. Dual-link DVI is necessary to sup port the high data rate (dot clock) as required by this high resolution of 2048 x 2048. However, the monitor also supports lower resolutions (e.g. VGA, SVGA, XGA, SXGA, UXGA, etc.) using a single link DVI cable. This f ...

  • Eizo SQ2801 - page 25

    2.3.3 RS232-1 Interface This RS232 interface is used for communication with the host machine (workstation). Three different protocols are available which are described in chapter 4 on page 43. In addition, this interface is used for monitor firmware updates NOTE Only the RS232-1 interface can be used for monitor firmware update. Connector Assignmen ...

  • Eizo SQ2801 - page 26

    2.3.5 RS422 Interface The RS422 interface is used for communication with a workstation. Three different protocols are available which are described in chapter 4 on page 43. NOTE This interface may also be used for communication with a workstation via DDM-protocol. However, no handshake signals are available. If the monitor has to be connected via R ...

  • Eizo SQ2801 - page 27

    2 General Installation 27 2.3.6 External OSD-Keyboard Interface This connector is for an external passive ke yboar d which has exactly same functionality as the buttons on the front of the panel, used to control the OSD (on screen display) (see section 3.1, page 28). An external keyboard allows operation of the monitor when the front side keyboard ...

  • Eizo SQ2801 - page 28

    3 Operation and Adjustment The manual operation and adjustment of the monitor is facilitated by buttons that are integrated on the front of the unit. The buttons are used for navigation and control of the OSD menu. Alternatively, all adjustments for brightness, contrast, etc. can be carried out via an external keyboard or via the serial interfaces ...

  • Eizo SQ2801 - page 29

    3.2 OSD-Menu / Quick-OSD-Menu In addition to detailed adjustments in the OSD-Menu, there is ano ther option available for adjusting frequently used functions such as brightness and contrast via direct access (remotely), the so called Quick-OSD-Menu . The protocols for access are discussed in Chapter 4. All settings and adjustments of the OSD are st ...

  • Eizo SQ2801 - page 30

    3.2.2 OSD-Menu The OSD ( O n S creen D isplay) is a menu system which is displayed on the scr een. All monitor settings and adjustments are done by operating the OSD OSD options depend on the selected signal source (RGB or DVI). For example, functio ns for frequency and phase adjustment of analog signal sources are not available when the unit is di ...

  • Eizo SQ2801 - page 31

    Function Description RGB DVI Frequency Frequency adjustment, see section 3 .3.1 page 41 Setting range: depends on input timing / resolution X Scaling Scaling adjustment if input resolution is lower than 2048 x 2048 Setting range : One to One: Display signal without scaling. Fill All: The input signal is displayed full screen. Fill Aspect Ratio: The ...

  • Eizo SQ2801 - page 32

    3.2.2.2 OSD-Menu (Advanced) Fig. 17: OSD-Menu (advanced) Function Description RGB DVI Sharpness Sharpness adjustment of the picture; choose from 1 = sharp to 5 = smooth. This function is only available, if the input resolution is lower than target resolution 2048 x 2048. Setting range: 1 to 5 X X Gamma Gamma – Curve selection Setting range: Linea ...

  • Eizo SQ2801 - page 33

    3.2.2.3 OSD-Menu - Options 1 Fig. 18: OSD-Menu - Options 1 Function Description RGB DVI OSD Choose among nine predefined OSD positions X X OSD H-Pos. Shift OSD-menu in horizontal direction Setting range: 0 to 100 X X OSD V-Pos. Shift OSD-menu in vertical direction Setting range: 0 to 100 X X OSD Timeout Timeout for OSD menu; OSD disappears after th ...

  • Eizo SQ2801 - page 34

    3.2.2.4 OSD-Menu - Options 2 Fig. 19: OSD-Menu - Options 2 Function Description RGB DVI DPMS Display power management system If DPMS is active, the monitor shuts down when there no sync signals Setting range: off; on X X Source scan Automatic scan for input sources; scans all input interfaces for valid input signal. Setting range: off; on X X Sourc ...

  • Eizo SQ2801 - page 35

    Function Description RGB DVI DDM contrast DDM control function assignment to DDM protocol 0xA1 Valid functions: backlight, brightness, contrast, disabled X X DDM brightness DDM control function assignment to DDM protocol 0xA0 Valid functions: backlight, brightness, contrast, disabled X X Fans supervision ON : number of number of rotation will be sh ...

  • Eizo SQ2801 - page 36

    3.2.2.5 OSD-Menu - Options 3 Fig. 20: OSD-Menu - Options 3 Function Description RGB DVI RGB-noise suppression This function suppresses interference at the sync signal line s to avoid a new auto adjustment during short interference. Setting range: off; on X X Lock RGB-Timing 1 The current video timing will be stored and processed with higher toleran ...

  • Eizo SQ2801 - page 37

    3.2.2.6 OSD-Menu – Utilities Fig. 21: OSD-Menu – Utilities Function Description RGB DVI Language Select language of OSD Menu Setting range: English; German X X Calibration This function allows to calibrate the A/D converter X Freeze frame Saves the actual image X X Factory reset Reset of all parameters (brightness, contrast, backlight brightnes ...

  • Eizo SQ2801 - page 38

    3.2.2.7 OSD-Menu - Utilities / Installation RGB-Mode Fig. 22: OSD-Menu - Utilities / Installation RGB-Mode Function Description RGB DVI Options Select the RGB installation mode for those timings which are not part of the internal timing list. Disabled: use only the internal timing table. Mode1: use timing parameters and carry out complete auto adju ...

  • Eizo SQ2801 - page 39

    3.2.2.8 OSD-Menu - Infos 1 Fig. 23: OSD-Menu – Infos 1 Function Description RGB DVI FW Shows the firmware version of the controller board X X Temperature Shows internal temperature X X Power on time Shows power-on time of the monitor (main power connected to the unit and switched on) X X Upper b.l. unit on time Shows backlight on time of upper ba ...

  • Eizo SQ2801 - page 40

    3.2.2.9 OSD-Menu - Infos 2 Fig. 24: OSD-Menu – Infos 2 Function Description RGB DVI Vdd-fuse Shows status of main power fuse X X Backlight inverter fuse Shows status of backlight inverter fuse X X Upper backlight unit Shows status of upper backlight unit X X Middle backlight unit Shows status of middle backlight unit X X Lower backlight unit Show ...

  • Eizo SQ2801 - page 41

    3.3 Adjustment Analog Signal Source (DDM) There is no strict standardization for the signals coming from analog signal sources. Certain adjustments are therefore necessary, depending on the graphics ad aptors and used cables. When the Raptor SQ2801 is connected to an analog signal source for the first time, an integrated “automatic adjustment” ...

  • Eizo SQ2801 - page 42

    With bad frequency adjustment from left to right, parts of the picture appear blurred. Each alteration of the frequency increases or decreases the number of blurred fields. Correct sett ing is achieved when the whole screen has the same appearance. The picture may appear blurry, but it should be homogeneously across the whole screen. Blurry or mess ...

  • Eizo SQ2801 - page 43

    Serial Communication 4 Serial Communication The Raptor SQ2801 features as described in C hapter 3 can be controlled via an application on the host workstation. The host workstation can communicate with the Raptor SQ2801 via the serial communication alternatives and protocols as described in this chapter. There are two channels for serial communicat ...

  • Eizo SQ2801 - page 44

    4.1 Standard Protocol 4.1 Standard Protocol The standard protocol supports all adjustments and cont rol of the monitor. This protocol u ses two kinds of data packet types. Packet format called “Operation” is used for adjustments such as brightness, contrast and backlight brightness. The packet type called “key simulation” is used to operate ...

  • Eizo SQ2801 - page 45

    4.1.1 Data Packet Structure “Operation” Byte No 0 1 2 3 4 5 6 7 8 9 10 Data 0xBE 0xEF 0x03 0x19 0x00 CRC-L CRC-H O-Type Code-L Code-H 0x00 Byte No 11 12 13 14 15 16 17 18 19 20 21 Data 0x00 0x00 0x00 0x00 0x00 Val-L Val-1 Val-2 Val-H 0x00 0x00 Byte No 22 23 24 25 26 27 28 29 30 31 Data 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 -L = Lowe ...

  • Eizo SQ2801 - page 46

    4.1.2 Data Packet Structure “Keyboard Simulation” 4.1.2 Data Packet Structure “Keyboard Simulation” Byte No. Byte No. 0 0 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 Data 0xBE 0xEF 0x02 0x06 0x00 CRC-L CRC-H Code-L Code-H 0x00 0x00 Byte No. 11 12 Data 0x00 0x00 L = Lower B yte H = Higher Byte Code (WORD) : Key code Following codes are support ...

  • Eizo SQ2801 - page 47

    4.1.3 Calculation of CRC - Check Sum For CRC check sum calculation set 0x00 for CRC-L and CRC-H. Check sum is calculated accor ding to a reference table. WORD CalculateCRC16(BYTE *pcData, int nCount) { BYTE cCRCHi = 0xFF; // high byte of CRC initialised BYTE cCRCLo = 0xFF; // low byte of CRC initialised BYTE cIndex; // will index into CRC lookup ta ...

  • Eizo SQ2801 - page 48

    0x22, 0xE2, 0xE3, 0x23, 0xE1, 0x21, 0x20, 0xE0, 0xA0, 0x60, 0x61, 0xA1, 0x63, 0xA3, 0xA2, 0x62, 0x66, 0xA6, 0xA7, 0x67, 0xA5, 0x65, 0x64, 0xA4, 0x6C, 0xAC, 0xAD, 0x6D, 0xAF, 0x6F, 0x6E, 0xAE, 0xAA, 0x6A, 0x6B, 0xAB, 0x69, 0xA9, 0xA8, 0x68, 0x78, 0xB8, 0xB9, 0x79, 0xBB, 0x7B, 0x7A, 0xBA, 0xBE, 0x7E, 0x7F, 0xBF, 0x7D, 0xBD, 0xBC, 0x7C, 0xB4, 0x74, 0x ...

  • Eizo SQ2801 - page 49

    4.2 Simplified Protocol The simplified protocol uses a data packet structure similar to the stan dard protocol, however with reduced functional range. Calculation of CRC check sum is similar to description in section 4.1.3 page 47. Interface Parameters Baud-Rate 19200 Parity None Data-Bits 8 Stop Bits 1 Handshake No ACK-Message OK 0x06 Protocol Hos ...

  • Eizo SQ2801 - page 50

    CMD CMD Code Command Comment 0x01 Status Reply of system status Host Monitor Byte 03: L-Len = 0x01 Byte 04: H-Len = 0x00 Monitor Host Byte 03: L-Len = 0x0E Byte 04: H-Len = 0x00 Byte 08: Status Information Display Module - Bit 0: VDD - fuse faulty - Bit 1: Backlight inverter – fuse faulty - Bit 2: Upper backlight unit faulty - Bit 3: Middle backl ...

  • Eizo SQ2801 - page 51

    Code Command Comment 0x02 Source Switch This command enables the host to switch signal source. Host Monitor Byte 03: L-Len = 0x01 Byte 04: H-Len = 0x00 Byte 08: Input - Source 0 = RGB-Analog1 1 = DVI 1 2 = DVI 2 3 = RGB-Analog2 Monitor Host Byte 00: ACK = 0x06 ACK is sent after the monitor has internally switched the source. CRC-Check sum for indiv ...

  • Eizo SQ2801 - page 52

    Code Command Comment 0x04 Brightness This command is used to adjust brig htness (black level). Host Monitor Byte 03: L-Len = 0x02 Byte 04: H-Len = 0x00 Byte 08: Brightness value (0 .. 255) Monitor Host Byte 00: ACK = 0x06 Value 0 to 255 corresponds 0 to 100% of adjustm ent range. 0x05 Contrast This command is used to adjust contrast. Host Monitor B ...

  • Eizo SQ2801 - page 53

    List of implemented commands: Code Command Comment 0xA0 Operator Brightness This command is used to set Backlight brightness. 0xA1 Operator Contrast This command is used to set contrast. Code Command Comment 0xB8 Status Response System Status Byte 0: Status Information Display-Module - Bit 0: VDD-fuse faulty - Bit 1: Backlight inverter-fuse faulty ...

  • Eizo SQ2801 - page 54

    5 Technical Data 5.1 Display Module Type Color active TFT-LCD Diagonal 28.05" Display area (WxH) 503.808 x 503.808 mm² Resolution 2048 x 2048 Pixel Pitch 0.246 x 0.246 mm² Colors 16.7 Million Viewing angle typ. horizontally (CR >= 10) vertically ± 85° ± 85° Contrast ratio typ. 1000 : 1 Response time White Black Black White 5 ms 20 ms ...

  • Eizo SQ2801 - page 55

    5.3 Operating Conditions Operating temperature 0 to +40 °C Storage temperature -25 to +60 °C Humidity max. 95 % (no condensation) 5.4 Protection Protection None Front shield antireflective 5.5 Housing Weight approx. 29.1 kg Material of housing Sheet steel Color of housing RAL 9005 (jet black) 5.6 Input signal RGB analog Level (Video) 0.7 Vss RGB ...

  • Eizo SQ2801 - page 56

    5.7 Standard ATC-Timing H-Frequency 126.84 KHz Pixel clock 357 MHz H-Total 2816 pixel H-Visible 2048 pixel V-Frequency 60 Hz V-Total 2114 lines V-Visible 2048 lines 5.8 Input Signal DVI-1 / DVI-2 Signal Standard DVI 1.0 Pixel clock max. 2 x 165 MHz 5.9 Recommended DVI-Timing 2,048 x 2,048 Pixel H-Frequency 124.8 KHz Pixel clock 260 MHz (2 x 130 MHz ...

  • Eizo SQ2801 - page 57

    5.10 EU – Declaration of Conformity on EMC Product LCD-Monitor Raptor SQ2801 Test guidelines EG-guide lines No 2004/108/EC No 2006/95/EC Harmonized standards used EN 55022 Class B +A1/EN55022/A1 Interference emissions (industrial) EN55024:1998 +A1:2001+A2:2003 Interference resistance (industrial) EN 60950 Safety 57 5 Technical Data ...

  • Eizo SQ2801 - page 58

    6 Part Numbers and Field Replaceable Units (FRUs) 6.1 TSI ATC Visualization Kit The Raptor SQ2801 is part of the Tech Source ATC Visualization kit (19-0206-01) and is comprised of the following components: Part Number Description 19-0152-01 Raptor 2500T-DL 2Kx2K Graphics Accelerator 19-0201-01 Raptor SQ2801 Display (Desktop version) 15-0231-01 Dual ...

  • Eizo SQ2801 - page 59

     1st Edition-October, 2007 03V22230A1 (U.M-SQ2801-EN) ...

Manufacturer Eizo Category Computer Monitor

Documents that we receive from a manufacturer of a Eizo SQ2801 can be divided into several groups. They are, among others:
- Eizo technical drawings
- SQ2801 manuals
- Eizo product data sheets
- information booklets
- or energy labels Eizo SQ2801
All of them are important, but the most important information from the point of view of use of the device are in the user manual Eizo SQ2801.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Eizo SQ2801, service manual, brief instructions and user manuals Eizo SQ2801. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Eizo SQ2801.

Similar manuals

A complete manual for the device Eizo SQ2801, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Eizo SQ2801 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Eizo SQ2801.

A complete Eizo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Eizo SQ2801 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Eizo SQ2801, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Eizo SQ2801, that we can find in the current document
3. Tips how to use the basic functions of the device Eizo SQ2801 - which should help us in our first steps of using Eizo SQ2801
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Eizo SQ2801
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Eizo SQ2801 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Eizo SQ2801?

Use the form below

If you did not solve your problem by using a manual Eizo SQ2801, ask a question using the form below. If a user had a similar problem with Eizo SQ2801 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)