English dropdown-ico

Manual Delta 36-220

23 pages 1.68 mb
Download

Go to site of 23

Summary
  • Delta 36-220 - page 1

    INSTRUCTION MANUAL 10" Compound Miter Saw (Model 36-220) P ART NO. 900327 - 01-01-01 Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 23 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta 36-220 - page 2

    2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will con- siderably lessen the possibility of personal injury . However , if normal safety precautions a ...

  • Delta 36-220 - page 3

    ADDITIONAL SAFETY RULES FOR COMPOUND MITER SA WS 3 1. USE ONL Y CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES, MAKE SURE THEY HA VE A NEGA TIVE HOOK ANGLE. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT GUARD. 2. DO NOT OPERA TE the miter saw until it is com- pletely assembled and installed according to the instru ...

  • Delta 36-220 - page 4

    4 CONNECTING COMPOUND MITER SA W T O POWER SOURCE Y our new Compound Miter Saw is DOUBLE INSULA TED to give you added safety . As a result, this saw is equipped with a two-prong plug which permits you to use any conventional 120 V olt electrical outlet without concern for main- taining a ground connection. Before connecting the motor to the power s ...

  • Delta 36-220 - page 5

    5 OPERA TING INSTRUCTIONS FOREWORD Delta Model 36-220 is a 10" Compound Miter Saw designed to cut wood. It can crosscut up to 2- 3 /4 " x 5- 1 /8 ", miter at 45 ° both left and right 2- 3 /4 " x 3- 1 /2 ", bevel at 45 ° left 1- 3 /4 " x 5- 1 /8 ", and compound 45 ° x 45 ° , 1- 3 /4 " x 3- 1 /2 ". It ...

  • Delta 36-220 - page 6

    6 Fig. 2 Fig. 3 Fig. 4 1. Push down on the cuttinghead handle slightly and rotate latch (A) Fig. 2, to the other side. 2. The cuttinghead will then move to the up position and the lower blade guard link (B) Fig. 3, will hang freely in the down position, as shown. 3. Remove special screw (C) Fig. 3, from the pivot bracket. 4. Insert special screw (C ...

  • Delta 36-220 - page 7

    7 Fig. 5 ASSEMBLING ST OCK ST OP AND T ABLE EXTENSIONS 1. Decide on which side of the saw table you want the stock stop (A) Fig. 5, to be, and assemble stock stop (A) onto table extension (B), as shown. NOTE: The most commonly used position of the stock stop will be on the right hand table extension, as shown. Fig. 6 Fig. 7 Fig. 8 2. Insert ends of ...

  • Delta 36-220 - page 8

    8 Fig. 12 Fig. 1 1 Fig. 10 Fig. 9 ASSEMBLING ACCESSOR Y WORK CLAMP T O SA W 1. The work clamp (A) Fig. 9, can be used on either the right or left side of the saw base. Insert post of work clamp into the hole located on the front of the saw base, as shown. Work clamp 36-221 is available as a accesso- ry . (See ASSESSORIES section) 2. IMPORT ANT : Th ...

  • Delta 36-220 - page 9

    9 ST ARTING AND ST OPPING SA W T o turn the saw “ON” push in on switch lock key (A) Fig. 13, and depress switch trigger (B). T o turn the saw “OFF” release switch trigger (B). Y our compound miter saw is equipped with an automatic electric blade brake. As soon as the switch trigger (B) Fig. 13, is released, the electric brake is activated a ...

  • Delta 36-220 - page 10

    10 Fig. 17 Fig. 16 Fig. 15 ROT A TING T ABLE FOR MITER CUTTING Y our compound miter saw will cut any miter angle from a straight 90 degree cut-off to 47 degrees right and lef t. Simply loosen lock handle (A) Fig. 14, depress index lever (B) and move the control arm to the desired angle. Then tighten lock handle (A). The 10" Compound Miter Saw ...

  • Delta 36-220 - page 11

    11 Fig. 18 LOCKING CUTTING ARM IN THE DOWN POSITION When transporting the saw , the cutting arm should always be locked in the down position. This can be accomplished by lowering the cutting arm (A) Fig. 18, and moving the locking lever (B) to the locked position, as shown. IMPORT ANT : NEVER CARRY THE COM- POUND MITER SA W BY THE SWITCH HANDLE, CU ...

  • Delta 36-220 - page 12

    12 Fig. 22 Fig. 21 ADJUSTMENTS ADJUSTING 90 AND 45 DEGREE BEVEL ST OPS 1. DISCONNECT THE SA W FROM THE POWER SOURCE . 2. Loosen bevel lock handle and tilt the cutting arm all the way to the right and tighten the bevel lock handle. 3. Using a square (A) Fig. 21, place one end of the square on the table and the other end against the blade. Check to s ...

  • Delta 36-220 - page 13

    13 Fig. 26 ADJUSTING BLADE P ARALLEL T O T ABLE SLOT 1. DISCONNECT THE SA W FROM THE POWER SOURCE . 2. NOTE: This adjustment should be checked with the cutting arm moved all the way to the right (blade 90 degrees to the table). 3. Lower the cutting arm. The saw blade (A) Fig. 25, should be parallel to the lef t edge (B) of the table insert opening. ...

  • Delta 36-220 - page 14

    14 Fig. 28 Fig. 29 7. Loosen the two fence locking screws, one of which is shown at (A) Fig. 28, and move the fence (B) all the way to the rear position, as shown. Then tighten the two fence locking screws (A). 8. Using a square, place one end of the square against the blade and the other end against the table and check to see if the fence is 90 de ...

  • Delta 36-220 - page 15

    15 Fig.31 Fig. 32 Fig. 33 ADJUSTING DOWNW ARD TRA VEL OF SA W BLADE 1. DISCONNECT THE SA W FROM THE POWER SOURCE . 2. The downward travel of the saw blade can be limited to prevent the saw blade from contacting any met al sur- faces of the machine. This adjustment is made by loos- ening locknut (A) Fig. 31, and turning adjusting screw (B) in or out ...

  • Delta 36-220 - page 16

    16 Fig. 34 Fig. 35 Fig. 36 9. Fig. 34, illustrates the work clamp (B) being used to firmly hold the workpiece against the fence. 10. Fig. 35, illustrates the cuttinghead tilted and the arm in a miter position for a compound miter/bevel cutting operation. 1 1. Fig. 36, illustrates the fence in the forward position enabling you to cross-cut a standar ...

  • Delta 36-220 - page 17

    17 Fig. 37 Fig. 38 Fig. 39 When performing multiple or repetitive cut-off operations that result in small cut-off pieces, one inch or less, it is possible for the saw blade to catch the cut-off pieces and project them out of the machine or into the blade guard and housing, possibly causing damage or injury . In order to limit the possibility of per ...

  • Delta 36-220 - page 18

    18 Fig. 43 MAINTENANCE CHANGING THE BLADE W ARNING: USE ONL Y CROSS-CUTTING SA W BLADES. WHEN USING CARBIDE TIPPED BLADES, MAKE SURE THEY HA VE A NEGA TIVE HOOK ANGLE. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT GUARD . 1. DISCONNECT THE SA W FROM THE POWER SOURCE . 2. Rotate lower blade guard (A) Fig. 40, to the top posi- ...

  • Delta 36-220 - page 19

    19 Fig. 44 Fig. 45 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING BRUSHES, DIS- CONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed. After the first check, examine them af ...

  • Delta 36-220 - page 20

    20 Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product pr e- paid to a Delta factory service center or authorized service station with proof of pur chase of the ...

  • Delta 36-220 - page 21

    21 NOTES ...

  • Delta 36-220 - page 22

    22 NOTES ...

  • Delta 36-220 - page 23

    The following are trademarks of POR TER-CABLE • DEL T A Corporation (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORT A-BAND ® , PORT A-PLANE ® , PORTER-CABLE ® , QUICKSAND ® , SANDTRAP ® , SA W BOSS ® , SPEED-BLOC ® , S ...

Manufacturer Delta Category Cordless Saw

Documents that we receive from a manufacturer of a Delta 36-220 can be divided into several groups. They are, among others:
- Delta technical drawings
- 36-220 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta 36-220
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta 36-220.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta 36-220, service manual, brief instructions and user manuals Delta 36-220. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta 36-220.

Similar manuals

A complete manual for the device Delta 36-220, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta 36-220 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta 36-220.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta 36-220 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta 36-220, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta 36-220, that we can find in the current document
3. Tips how to use the basic functions of the device Delta 36-220 - which should help us in our first steps of using Delta 36-220
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta 36-220
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta 36-220 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta 36-220?

Use the form below

If you did not solve your problem by using a manual Delta 36-220, ask a question using the form below. If a user had a similar problem with Delta 36-220 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)