Manual Furuno IF-NMEASC

28 pages 1.26 mb
Download

Go to site of 28

Summary
  • Furuno IF-NMEASC - page 1

    INTERF A CE UNIT IF-NMEASC OPERA T OR'S MANU AL www .furuno .co.jp MODEL ...

  • Furuno IF-NMEASC - page 2

    ...

  • Furuno IF-NMEASC - page 3

    i IMPORTANT NOTICES • This manual is intended fo r use by readers with a solid knowledg e of English. • No part of this manual may be copied or reproduced wit hout written permis sion. • If this manual is los t or worn, contact your dealer about repla cement. • The contents of this ma nual and equipment specific ations are subjec t to chang ...

  • Furuno IF-NMEASC - page 4

    ii SAFETY INSTRUCTIONS WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. Warning, Caution Mandatory Action Prohibitive Action The operator and installer must read the ap ...

  • Furuno IF-NMEASC - page 5

    SAFETY INSTRUCTIONS iii CAUTION CAUTION Observe the following compass safe distances to prevent interference to a magnetic compass: Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. Do not install the equipment where it may get wet from rain or water splash. Water i ...

  • Furuno IF-NMEASC - page 6

    iv TABLE OF CONTENTS FOREWORD ......... .............. .......... .............. .............. ......... .............. .............. .............. .... v SYSTEM CONFIGURATION ............ .......... .............. .............. .............. ......... .............. ... vi 1. MOUNTING ......... .............. .............. ......... ........ ...

  • Furuno IF-NMEASC - page 7

    v FOREWORD A Word to the Owner o f the IF-NMEASC Congratulations on your choice of the FURUNO IF-NMEASC Interface Uni t. We are confident y ou will see why the FURUNO name has become synonymous with quality and reli ability. For 60 year s FURUNO Electric Company has e njoyed an enviable reputation for qualit y mari ne electroni cs equipment. This d ...

  • Furuno IF-NMEASC - page 8

    vi SYSTEM CONFIGURATION SC-30 12-24 VDC : Standard supply : Local supply IF-NMEASC INTERF A CE UNIT Radar Current Indicator Scanning Sonar Other NMEA 2000 AD-10 NMEA 0183 Video Plotter Radar A utopilot Current Indicator Scanning Sonar Video Sounder ECDIS AIS Current Indicator Scanning Sonar Other Roll, Pitch IF-NMEASC ...

  • Furuno IF-NMEASC - page 9

    1 1. MOUNTING 1.1 Equip ment List 1.2 Mountin g Procedu re When choosing a mounting l ocation for the unit, keep the following points in mind: • Select a location where shock and vibr ation are minimal. • Locate the unit away from places subject to rain or water splash. • Keep th e unit away from exhaust pipes and vent s. • Locate the unit ...

  • Furuno IF-NMEASC - page 10

    2 2. WIRING Open the IF unit with your hands, det ach the shield cover and connect external equipment , refer- ring to t he illustrati on below and t he interc onnection diagram. Cables are mainl y connected to the unit wit h WAGO connectors. See the instr uctions bel ow for how t o attach wir ing to th e connectors. The opener f or the WAGO connec ...

  • Furuno IF-NMEASC - page 11

    2. WIRING 3 Cable constru ction 3 Approx. 70 Armor Braided shield Data cable TTYCS-1 or equivalent Data cable TTYCS-4 or equivalent Power cable DPYC-1.5 or equivalent Approx. 40 3 Armor Sheath Vinyl tape 45 Scrape off paint. Lay this part on applicable cable post and fix with two cable ties . Vinyl tape 45 Scrape off paint. Lay this part on applica ...

  • Furuno IF-NMEASC - page 12

    4 3. ADJUSTMENTS 3.1 LEDs and Equ ipmen t Status The six LEDs above t he heading i ndication l ight, flas h or go of f accordi ng to equipment status . LED state an d equipment stat us LED LED sta te and eq uipmen t status GPS ON: Both GPS antenn as in the SC -30 are r eceivin g from fiv e or more sat el- lites. OFF: One of the GP S ante nnas is re ...

  • Furuno IF-NMEASC - page 13

    3. ADJUSTMENTS 5 3.2 Setting Up NMEA Ports Ports J4 an d J5 output data in NMEA 0183 form at. Select the data t o output f rom tho se ports, along with baud rate and outpu t interval . The default settings are as shown in the table below. Default settings for ports 2 and 3 1. Grasp the cover at its ri ght and left sides, pull t he cover outward s l ...

  • Furuno IF-NMEASC - page 14

    3. ADJ USTMENT S 6 7. Push the [Menu/Cancel] button to light the Bps LED on the Port 2 line. 8. Push the [Enter] butt on. The Bps LED starts flashing and the current bps setting appears . 9. Push the [+] or [-] b utton to selec t desired baud rate. The choices are 4800, 9600, 19200 and 38400 (bps) . 10. Push the [Ent er] button. The bps LED stops f ...

  • Furuno IF-NMEASC - page 15

    3. ADJUSTMENTS 7 13. Push the [+] or [-] but ton to select desired out put interval , referring to the table below. 14. Push the [ Enter] butt on. The outp ut int erval LED stop s flashi ng. 15. Set up Por t 3 simila r to how you did Port 2. 16. Close the inner and outer cover s. Senten ce number Sentence Output inte rval (ms) 4800 bps 9600 bps 192 ...

  • Furuno IF-NMEASC - page 16

    3. ADJ USTMENT S 8 3.3 Hea ding, Pitch and Roll Offsets Turn on the IF uni t and wait approx. thre e minutes for t he satelli te compass to set tle. Then, ch eck that heading, pi tch and roll data are reasonable. If not, open the uni t and enter appropri ate off- set(s). 1. Open the cover, referr ing to step 1 in the previ ous section for th e proc ...

  • Furuno IF-NMEASC - page 17

    9 4. OPERATION Normally, no operati on is requi red except to power the unit (from the switchboar d). The ST- BY LED on the cov er i s ON, OFF or fl ashing accor ding to equipment stat e. Flashin g: NMEA 2000 data is input ON: NMEA 2000 da ta is not input OFF: Power loss, bl own fuse, operation erro r IF-NMEASC INTERFACE UNIT ST-BY ST-BY LED ...

  • Furuno IF-NMEASC - page 18

    10 5. MAINTENANCE, TROUBLE- SHOOTING This chapte r provides the inf ormation f or keeping your unit i n good worki ng order. 5.1 Preventive Maintena nce Regular maint enance is i mportant f or good perf ormance. Foll owing the proce dures in t he table be- low will help main tain perform ance Preventive maint enance Item Check point Remed y Cabli n ...

  • Furuno IF-NMEASC - page 19

    5. MAINTE NANCE, TROUBLE SHOOTING 11 5.2 Replacing the Fuse The 2A fuse inside the unit protects it from overcu rrent and equipme nt fault. If the power canno t be turned on, have a quali fied technician c heck the fuse. If the fuse has blown, find out th e cause before replaci ng it. If it blows again, contact your dealer for advi ce. 5.3 T rouble ...

  • Furuno IF-NMEASC - page 20

    5. MAINTENANC E, TROUBLESH OOTING 12 5.4 Self Test The self tests check the equipment for proper operat ion. Self test 1 This test checks the two GPS receiver s, output circuit, processor and two sensors fo r proper op- eration. 1. Remove the cover and shiel d cover f rom the equipment. 2. Press the [Menu/ Cancel] butt on several t imes to show &qu ...

  • Furuno IF-NMEASC - page 21

    5. MAINTE NANCE, TROUBLE SHOOTING 13 Self test 2 This test checks thi s unit' s processor and output for prop er operati on. 1. With the display showing " - - - .1", push the [Menu/Cancel] button. The display shows "- - - 2". 2. Press the [Enter] button t o start the test. If t he results ar e normal all LEDs light. Then, t ...

  • Furuno IF-NMEASC - page 22

    5. MAINTENANC E, TROUBLESH OOTING 14 This page i s in tentionall y left blank. ...

  • Furuno IF-NMEASC - page 23

    FURUNO IF-NME A SC SP - 1 E 7265S 02A-M SPECIFICA TIONS OF INTERF A CE UNIT IF-N ME A SC 1 INPUT PORT NMEA 2000* , for da ta I/O be tween FURUNO satell ite compa ss SC-30 * NMEA 2000 is a re gistered t rademark of the Natio na l Marine Electron ics Associat ion. 2 OUT PUT POR T NMEA 0 183: Two po rts (HDT , HDG, HMD , ATT*, H VE*, VT G, GGA, RMC, Z ...

  • Furuno IF-NMEASC - page 24

    Jul.23'07 R.Esumi D-1 ...

  • Furuno IF-NMEASC - page 25

    2 4 3 A 1 B C 1 2 3 4 5 6 7 8 J7 NET_S NET_C NET_H アカ クロ シロ アオ ムラサキ キ ミドリ RED BLK WHT BLU PPL YEL GRN NET_L SG RD SD FG 1 2 3 4 J3 5F G AD-10 1 2 J4 TD-A TD-B FG 3 NMEA 1 2 TD-A TD-B FG 3 NMEA J5 IF-NMEASC インターフェイスユニット INTERFACE UNIT *2 1 2 J2 3 4 VBUS DM DP SG USB 1 2 TB1 (+) (-) 20P8195 1 ...

  • Furuno IF-NMEASC - page 26

    This page is intentionally left blank . ...

  • Furuno IF-NMEASC - page 27

    ...

  • Furuno IF-NMEASC - page 28

    The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : DEC 2007 . Printed in Japan All rights reserved. A1 : JAN . 28, 2008 Pub. No. OME-72651-A1 *00016689910* *00016689910* ( DAMI ) IF-NMEASC * 0001 ...

Manufacturer Furuno Category Network Router

Documents that we receive from a manufacturer of a Furuno IF-NMEASC can be divided into several groups. They are, among others:
- Furuno technical drawings
- IF-NMEASC manuals
- Furuno product data sheets
- information booklets
- or energy labels Furuno IF-NMEASC
All of them are important, but the most important information from the point of view of use of the device are in the user manual Furuno IF-NMEASC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Furuno IF-NMEASC, service manual, brief instructions and user manuals Furuno IF-NMEASC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Furuno IF-NMEASC.

Similar manuals

A complete manual for the device Furuno IF-NMEASC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Furuno IF-NMEASC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Furuno IF-NMEASC.

A complete Furuno manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Furuno IF-NMEASC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Furuno IF-NMEASC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Furuno IF-NMEASC, that we can find in the current document
3. Tips how to use the basic functions of the device Furuno IF-NMEASC - which should help us in our first steps of using Furuno IF-NMEASC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Furuno IF-NMEASC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Furuno IF-NMEASC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Furuno IF-NMEASC?

Use the form below

If you did not solve your problem by using a manual Furuno IF-NMEASC, ask a question using the form below. If a user had a similar problem with Furuno IF-NMEASC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)