English dropdown-ico

Manual Cisco Systems NME-16ES-1G

88 pages 0.93 mb
Download

Go to site of 88

Summary
  • Cisco Systems NME-16ES-1G - page 1

    Corporate Headquarters: Copyright © 2005 Cisco Systems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco EtherSwitch Service Modules Feature Guide Note This document describes the Cisco EtherSwitch serv ice modu le only . For infor mation about th e Cisco Ethernet switch netw ork module, see ? ...

  • Cisco Systems NME-16ES-1G - page 2

    Cisco EtherSwi tch Service Mo dules Feature Guide Contents 2 Cisco IOS Release 12.2(25)SEC Finding Support Information for Platforms and Cisco IOS Software Images Use Cisco Feature Na vigato r to fi nd information about platform support and Cisco IOS softwa re image support. Access Cisco Feature Navigator at http://www .cisco.com/go/fn . Y ou must ...

  • Cisco Systems NME-16ES-1G - page 3

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 3 Cisco IOS Release 12.2(25)SEC Hardware Overview Cisco EtherSwitch service modules are modules to which you can connect devices such as Cisco IP phones, Cisco wireless access points, workstations, and other netwo rk de vices such as servers, ...

  • Cisco Systems NME-16ES-1G - page 4

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 4 Cisco IOS Release 12.2(25)SEC • NME-XD-48ES-2S-P—Extended double-wi de Cisco EtherSwitch servi ce module wit h 48 10/100-Mbps PoE ports, and 2 small form-fact or pluggable (SFP) Gigabit Ethernet ser vice module ports • NME-XD-24ES-1S- ...

  • Cisco Systems NME-16ES-1G - page 5

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 5 Cisco IOS Release 12.2(25)SEC Ease-of-Use and Ease-of-D eployment Features • Express Setup for quickl y config uring a Cisco Ethe rSwitch service module for th e f irst time with basic IP information, contact in formatio n, Cisco EtherSwit ...

  • Cisco Systems NME-16ES-1G - page 6

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 6 Cisco IOS Release 12.2(25)SEC • Cisco Group Management Protocol (CGMP) serv er support and Inte rnet Group Man agement Protocol (IGMP) s nooping fo r IGMP versions 1, 2, and 3: – (For CGMP de vices) CGMP fo r limiting multi cast traf f ...

  • Cisco Systems NME-16ES-1G - page 7

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 7 Cisco IOS Release 12.2(25)SEC Manageability Features Note The encrypted Secure Shell (SSH) f eature listed in this section is a v ailable o nly on the cryptographic versions of t he Cisco EtherSwitc h serv ice module softwar e image. • Cis ...

  • Cisco Systems NME-16ES-1G - page 8

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 8 Cisco IOS Release 12.2(25)SEC • IEEE 802.1D Spanning T ree Prot ocol (STP) for r edundant back bone connections and loop-free networks. STP has these features: – Up to 128 spanning-tree instances supported. – Per-VLAN spanning-tree pl ...

  • Cisco Systems NME-16ES-1G - page 9

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 9 Cisco IOS Release 12.2(25)SEC • V oice VLAN for crea ting subnets fo r voice traf f ic from Ci sco IP phones. • VLAN 1 minimization for red ucing the risk of spanning-tree loops or stor ms by allo wing VLAN 1 to be disabled on an y indi ...

  • Cisco Systems NME-16ES-1G - page 10

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 10 Cisco IOS Release 12.2(25)SEC • Kerberos sec urity system to authenticat e requests fo r network reso urces by using a tru sted third party (requir es the cryptographi c versio ns of the Cisco EtherSwitch service module softw are image) ...

  • Cisco Systems NME-16ES-1G - page 11

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 11 Cisco IOS Release 12.2(25)SEC • Egress queues and scheduling – Four egress queues p er port. – WTD as the congestion-avoidance mechanism fo r managing th e queue lengths and pro viding drop precedences for different traf f ic classif ...

  • Cisco Systems NME-16ES-1G - page 12

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 12 Cisco IOS Release 12.2(25)SEC Cisco StackWise Concepts This section des cribes the concep ts applicable t o switch stacks of Cisco EtherSwitc h service modules. • Overvie w of Switch Stack s, page 12 • Switch Stack M embership, page 13 ...

  • Cisco Systems NME-16ES-1G - page 13

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 13 Cisco IOS Release 12.2(25)SEC A switc h stac k is a set of Cisco Ether Switch service modules or Catalyst 3750 switch es connected through their C isco StackWise ports. One of the Cisco EtherSwitch serv ice modules or one of the Catalyst 37 ...

  • Cisco Systems NME-16ES-1G - page 14

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 14 Cisco IOS Release 12.2(25)SEC A standalone Ci sco EtherSwitch servic e module o r Catalyst 37 50 switch is a switch stack w ith one stack member that also operates as the stack master . Y ou can connect one standalone Cisco EtherSwitch ser ...

  • Cisco Systems NME-16ES-1G - page 15

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 15 Cisco IOS Release 12.2(25)SEC The Cisco EtherSwitch service module or switch using the v ersions listed belo w ar e ordered from highest t o lowest priority: – Cryptographic IP ser vices image – Noncryptographic IP services image – Cr ...

  • Cisco Systems NME-16ES-1G - page 16

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 16 Cisco IOS Release 12.2(25)SEC A ne w , out-of-the-box Ci sco EtherSwitch serv ice module (one that has not joined a switch stack or has not been manually assigned a stack member number) ships wit h a default st ack member number of 1. When ...

  • Cisco Systems NME-16ES-1G - page 17

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 17 Cisco IOS Release 12.2(25)SEC Switch Stack Software Compa tibility Recommendations All stack members must run the same Cisco IOS softwa re v ersion to ensure co mpatibility between stack members. W e recommend the follo wing: • The Cisco ...

  • Cisco Systems NME-16ES-1G - page 18

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 18 Cisco IOS Release 12.2(25)SEC Minor Incompatibility Between Cisco EtherSwitch Service Modules Cisco EtherSwitch service modules or Cat alyst 3750 switches wi th the same major ve rsion number b ut a different minor v ersion number as the s ...

  • Cisco Systems NME-16ES-1G - page 19

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 19 Cisco IOS Release 12.2(25)SEC The interface-specif ic configuration of each stack me mber is associated with the stack member number . As mentioned in the “Sta ck Member Nu mbers” se ction on p age 15 , stack members retain their number ...

  • Cisco Systems NME-16ES-1G - page 20

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 20 Cisco IOS Release 12.2(25)SEC Be careful when using multiple CLI sessions to the stack master . Commands that you enter in one session are not disp layed in the other sessions. T herefore, it i s possible that you might not be able to iden ...

  • Cisco Systems NME-16ES-1G - page 21

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 21 Cisco IOS Release 12.2(25)SEC • Other Considerations for Cluster St andby G roups, page 28 • Automatic Reco very of Clus ter Conf iguration, page 29 • IP Addresses in Clusters, page 30 • Hostnames in Clusters, page 30 • Passwords ...

  • Cisco Systems NME-16ES-1G - page 22

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 22 Cisco IOS Release 12.2(25)SEC If you want to maintain the same le vel of featu re support when a standb y command de vice takes o v er , it should run the same release of Ci sco IOS softwa re that the command de vice runs. Candidate and Me ...

  • Cisco Systems NME-16ES-1G - page 23

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 23 Cisco IOS Release 12.2(25)SEC Figure 1 Discovery Thr ough CDP Hops Discovery of Candidates and Members Through Non- CDP-Capable and No ncluster-Capable Devices If a cluster command switch is connected to a non-CDP-ca pable thir d-party hub ...

  • Cisco Systems NME-16ES-1G - page 24

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 24 Cisco IOS Release 12.2(25)SEC Discovery of Candidates and Members Through Different VLANs If the cluster command switch i s a Cisco EtherSwitc h service module, the cluster can ha ve cluster member switches in dif ferent VLANs. As cluster ...

  • Cisco Systems NME-16ES-1G - page 25

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 25 Cisco IOS Release 12.2(25)SEC • Switch 9 because automatic d iscov ery does not ex te nd be yond a non candidate de vice, which is switch 7 Figure 4 Discovery Thr ough Diff er ent Management VLANs with a Lay er 3 Cluster Command Swi tch D ...

  • Cisco Systems NME-16ES-1G - page 26

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 26 Cisco IOS Release 12.2(25)SEC Figure 5 Discovery Thr ough Routed P orts Discovery of Newly Instal led Switches in Clusters T o join a cluster , the ne w , out-of-the-box switch mu st be connected to the cluster thro ugh one of its access p ...

  • Cisco Systems NME-16ES-1G - page 27

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 27 Cisco IOS Release 12.2(25)SEC HSRP and Standby Clus ter Command Switches The switch supports Hot Standb y Router P rotocol (HSRP) so that you can con figur e a group of standb y cluster command switches. Because a cluster co mmand switch ma ...

  • Cisco Systems NME-16ES-1G - page 28

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 28 Cisco IOS Release 12.2(25)SEC Virtual IP Addresses in Clusters Y ou need to assign a unique virtual IP ad dress and group number and name to the cluster stand by group . This information must be conf igur ed on a specif ic VLAN or routed p ...

  • Cisco Systems NME-16ES-1G - page 29

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 29 Cisco IOS Release 12.2(25)SEC • Each standb y-group member ( Figure 7 ) must be connected to th e cluster command switch through the same VLAN. In this e xample, the clus ter co mmand switch and standby cluster command switches are Cisco ...

  • Cisco Systems NME-16ES-1G - page 30

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 30 Cisco IOS Release 12.2(25)SEC • This limitation applies to all clusters: If t he activ e cluster comman d switch fails and becomes acti v e again, it does not disco v er any Catalyst 1900, Catalyst 2820, an d Catalyst 2916M XL cl uster m ...

  • Cisco Systems NME-16ES-1G - page 31

    Cisco EtherSwitch Service Mo dules Feature Guide Information About the Cisco Eth erSwitch Service Module s 31 Cisco IOS Release 12.2(25)SEC Passwords in Clusters Y o u do not need to assi gn passwords to an individual switch if it will be a clus ter member . When a switch joins a cluster , it inherits the command-swi tch password and retains it whe ...

  • Cisco Systems NME-16ES-1G - page 32

    Cisco EtherSwi tch Service Mo dules Feature Guide Information About th e Cisco EtherSw itch Service Modules 32 Cisco IOS Release 12.2(25)SEC Recall that stack members w ork together to beha v e as a unif ied system (as a single switch stack) in the network and are presented to the network as such b y Layer 2 and Layer 3 protocol s. Therefore, the s ...

  • Cisco Systems NME-16ES-1G - page 33

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 33 Cisco IOS Release 12.2(25)SEC • If the cluste r command switch is a switch s tack and ne w st ack masters are simultan eously el ected in the cluster command switch stack and in cluster member switch stacks, c onnectivity between the switch ...

  • Cisco Systems NME-16ES-1G - page 34

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 34 Cisco IOS Release 12.2(25)SEC • For de vice manager requirements, see the “System Requi rements” section in th e release notes (not orderable b ut av ailable on Cisco.com). • For Netw ork Assistant requirements, see Getti ng Started w ...

  • Cisco Systems NME-16ES-1G - page 35

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 35 Cisco IOS Release 12.2(25)SEC The interface numbering format on th e Cisco EtherSwitch service mo dule is stac k-member -number /0/ switc h-port . For more detail ed informati on about int erface types, see the Catalyst 3750 Switc h Softwar e ...

  • Cisco Systems NME-16ES-1G - page 36

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 36 Cisco IOS Release 12.2(25)SEC Configuring the Cisco EtherSwitch Service Module in the Router This section descri bes ho w to perform the initial co n fi guration on the ro uter with a Cisco EtherSwitch service mo dule installe d. This sect io ...

  • Cisco Systems NME-16ES-1G - page 37

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 37 Cisco IOS Release 12.2(25)SEC Step 3 enable Example: Router# enable Enters pri vileged EXEC mode. Step 4 show running configuration Example: Router# show running config interface gigabitethernet1/0 Displays the running conf iguration of the ro ...

  • Cisco Systems NME-16ES-1G - page 38

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 38 Cisco IOS Release 12.2(25)SEC Step 13 enable Example: Switch> enable Enters pri vile ged EXEC mode on the Cisco EtherSwit ch service module. Step 14 show ip interface brief Example: Switch# show ip interface brief Displays brief v ersion o ...

  • Cisco Systems NME-16ES-1G - page 39

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 39 Cisco IOS Release 12.2(25)SEC Examples This section provides the follo wing e xamples: • Sample Output for the di r flash: Command on the Router , page 39 • Sample Output for the boot f lash: Command on the Router , p age 39 • Sample Out ...

  • Cisco Systems NME-16ES-1G - page 40

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 40 Cisco IOS Release 12.2(25)SEC Sample Output for the show running config Command on the Router The follo wing example sho ws what appears when you enter the show running conf ig command: Router# show running config interface gigabitethernet2/0 ...

  • Cisco Systems NME-16ES-1G - page 41

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 41 Cisco IOS Release 12.2(25)SEC Sample Output for the show ip interface brief Command on the Cisco E therSwitch Service Module The follo wing example sho ws what appears when you enter the show ip interface brief command: Switch# show ip interfa ...

  • Cisco Systems NME-16ES-1G - page 42

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 42 Cisco IOS Release 12.2(25)SEC Default Settings After Initial Cisco Et herSwitch Service M odule Configuration The Cisco EtherSw itch servi ce module is designed fo r plug-and-play operation. Y ou need only assign basic IP information to the G ...

  • Cisco Systems NME-16ES-1G - page 43

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 43 Cisco IOS Release 12.2(25)SEC Default VLAN VLAN 1 VLAN trunking Dynamic auto (DTP) T runk encapsulati on Negot iate VTP 4 mode Server VTP version 1 V oice VLAN D isabled STP 5 PVST+ 6 enabled o n VLAN 1 MSTP 7 Disabled Optional spanning-tree f ...

  • Cisco Systems NME-16ES-1G - page 44

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 44 Cisco IOS Release 12.2(25)SEC Configuring the Cisco EtherSwitch Se rvice Module Using the Switch Setup Program This section describes ho w to conf igure the Cisco EtherSwitch service module, u sing the setup program on the service module to c ...

  • Cisco Systems NME-16ES-1G - page 45

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 45 Cisco IOS Release 12.2(25)SEC • Enable password • T elnet password Note If your Cisco EtherSwitch service modules are stack ed and there are multiple consol e connections to indi vidual Cisco EtherSwitch servi ce modules in the st ack, the ...

  • Cisco Systems NME-16ES-1G - page 46

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 46 Cisco IOS Release 12.2(25)SEC Examples This section provides the follo wing e xamples: • Sample Output for Initial Con fig uration Dialog and Basic Management Ini tiation, page 46 • Sample Output for Entering an Interface Name, page 47 ? ...

  • Cisco Systems NME-16ES-1G - page 47

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 47 Cisco IOS Release 12.2(25)SEC Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system. Would you like to enter basic management setup? [yes/ ...

  • Cisco Systems NME-16ES-1G - page 48

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Module 48 Cisco IOS Release 12.2(25)SEC Sample Output for Saving the Configuration to NVRAM The follo wing example sho ws what appears when yo u save the Cisco EtherSwitch service module configuration to NVRAM: [0] Go to the IOS command prompt without ...

  • Cisco Systems NME-16ES-1G - page 49

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco E therSwitch Service Module 49 Cisco IOS Release 12.2(25)SEC Examples This section provides the follo wing e xamples: • Sample Outpu t for the service-modu le gigabitethernet sh utdown Command, page 49 • Sample Output for the service-modul e gigabitethern et reset Comma ...

  • Cisco Systems NME-16ES-1G - page 50

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Modu le in a Switch Stac k 50 Cisco IOS Release 12.2(25)SEC How to Configure the Cisco EtherSwitch Service Module in a Switch Stack This section descri bes ho w to conf igure the Cisco EtherSwit ch service module in a swit ch stack. A switch stac k is ...

  • Cisco Systems NME-16ES-1G - page 51

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco EtherSwit ch Service Modu le in a Switc h Stack 51 Cisco IOS Release 12.2(25)SEC Default Switch Stack Configuration Ta b l e 3 shows th e default switch st ack conf iguration. Prerequisites • When the IP services image is running on the st ack master , the Cisco Ethe rSwi ...

  • Cisco Systems NME-16ES-1G - page 52

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Modu le in a Switch Stac k 52 Cisco IOS Release 12.2(25)SEC • Removing po wered-up stack members from the stack causes the Cisco EtherSwitch service module stack to di vide (partition) into two or more swit ch stacks, each with the same conf iguratio ...

  • Cisco Systems NME-16ES-1G - page 53

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco EtherSwit ch Service Modu le in a Switc h Stack 53 Cisco IOS Release 12.2(25)SEC Examples This section provides the follo wing e xamples: • Sample Output for the switch renu mber Command, page 53 • Sample Outpu t for the reload slot Comm and, page 53 • Sample Output f ...

  • Cisco Systems NME-16ES-1G - page 54

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Modu le in a Switch Stac k 54 Cisco IOS Release 12.2(25)SEC Sample Output for the show switch Command The follo wing example sho ws what appears when you enter the show switch command: Switch# Role Mac Address Priority State --------------------------- ...

  • Cisco Systems NME-16ES-1G - page 55

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure the Cisco EtherSwit ch Service Modu le in a Switc h Stack 55 Cisco IOS Release 12.2(25)SEC Examples This section provides the follo wing e xamples: • Sample Output for the switch pr iority Command, p age 55 • Sample Output for the sho w switch Command , page 55 Sample Output for ...

  • Cisco Systems NME-16ES-1G - page 56

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure the Cisco EtherSwitc h Service Modu le in a Switch Stac k 56 Cisco IOS Release 12.2(25)SEC DETAILED ST EPS Step 1 Use the show platform stack-manager command to display platform-depen dent switch-stack information. Use th e show platf orm stack-manager all command to display all inf ...

  • Cisco Systems NME-16ES-1G - page 57

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure a Switch Clu ster 57 Cisco IOS Release 12.2(25)SEC Switch(config)# show switch neighbors Switch # Port A Port B -------- ------ ------ 6 None 8 8 6 None • Use the show switch stack-ports user EXEC command to display po rt status on the stack members: Switch(config)# show switch sta ...

  • Cisco Systems NME-16ES-1G - page 58

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure a Sw itch Cluster 58 Cisco IOS Release 12.2(25)SEC This section contains the following procedures: • Using the CLI to Manage Switch Clusters, page 58 • Adding Cluster Member s to the Cisco EtherSwitch Service Module, page 60 • Creating a Cluster Standb y Group, page 62 Using t ...

  • Cisco Systems NME-16ES-1G - page 59

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure a Switch Clu ster 59 Cisco IOS Release 12.2(25)SEC Examples This section provides the follo wing e xamples: • Sample Output for the rcommand and sh ow version Commands, page 59 • Sample Output for the sho w cluster members Co mmand, page 59 Sample Output for the rcommand and show ...

  • Cisco Systems NME-16ES-1G - page 60

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure a Sw itch Cluster 60 Cisco IOS Release 12.2(25)SEC Adding Cluster Members to the Cisco EtherSwitch Service Module This section sho ws ho w to ad d cluster members to the Cisco EtherSwitch service module. The cluster command service modu le or switch auto matically d iscov ers candid ...

  • Cisco Systems NME-16ES-1G - page 61

    Cisco EtherSwitch Service Mo dules Feature Guide How to Configure a Switch Clu ster 61 Cisco IOS Release 12.2(25)SEC DETAILED STEPS FROM THE NETWORK ASSISTANT APPLICATION Command or Action Purpose Step 1 Close the Add to Cluster wi ndo w . Closes the Add to Cluster windo w to vie w an up dated list of cluster members. Step 2 Choose V iew > Refr ...

  • Cisco Systems NME-16ES-1G - page 62

    Cisco EtherSwi tch Service Mo dules Feature Guide How to Configure a Sw itch Cluster 62 Cisco IOS Release 12.2(25)SEC DETAILED STEPS FROM THE CLI Creating a Cluster Standby Group This section describes h ow to add Cisco EtherSwitch service modules to a cl uster standby gr oup and to bind the cluster standb y group to a cluster . Note Standby cluste ...

  • Cisco Systems NME-16ES-1G - page 63

    Cisco EtherSwitch Service Mo dules Feature Guide Upgrading the Cisco EtherSwit ch Service Module Software 63 Cisco IOS Release 12.2(25)SEC Restrictions • This task is a v ailable only on the stack master . • Y ou must enter a virtual IP address for the clust er standby g roup. This address mu st be in the same subnet as the IP addresses of th e ...

  • Cisco Systems NME-16ES-1G - page 64

    Cisco EtherSwi tch Service Mo dules Feature Guide Upgrading the Cisco E therSwitch Service Module Software 64 Cisco IOS Release 12.2(25)SEC SUMMARY STEPS 1. enable 2. conf igure termi nal 3. interfac e switch / slot/ port 4. no switchport 5. ip addr ess ip addr ess/subnet mask 6. no shutdown 7. end 8. show flash 9. copy tftp: flash: DETAILED ST EPS ...

  • Cisco Systems NME-16ES-1G - page 65

    Cisco EtherSwitch Service Mo dules Feature Guide Upgrading the Cisco EtherSwit ch Service Module Software 65 Cisco IOS Release 12.2(25)SEC Examples This section provides the follo wing e xamples: • Sample Output for the sho w run in terface f astethernet Command, page 65 • Sample Output for the pi ng tftpserv er Command, page 65 • Sample Outp ...

  • Cisco Systems NME-16ES-1G - page 66

    Cisco EtherSwi tch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Service Module Software 66 Cisco IOS Release 12.2(25)SEC Sample Output for the show flash: Command The follo wing example sho ws what appears when you enter the show flash: command: Switch# show flash: Directory of flash:/ 3 -rwx 4815232 Jan 1 1970 00:10:53 +00: ...

  • Cisco Systems NME-16ES-1G - page 67

    Cisco EtherSwitch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Servic e Module Software 67 Cisco IOS Release 12.2(25)SEC Recovering from a Corrupted Software Image Using Xmodem This section describes ho w to reco ve r from a corrupted software image by using Xmod em. Note The router should ha ve the swi tch image in the rout ...

  • Cisco Systems NME-16ES-1G - page 68

    Cisco EtherSwi tch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Service Module Software 68 Cisco IOS Release 12.2(25)SEC 7. service-module interface slot/port session 8. dir flash: 9. boot flash: image DETAILED ST EPS Command or Action Purpose Step 1 service-module interface slot/port password-reset Example: Router# service- ...

  • Cisco Systems NME-16ES-1G - page 69

    Cisco EtherSwitch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Servic e Module Software 69 Cisco IOS Release 12.2(25)SEC Troubleshooting If the downloaded image (f iles and directories) are not in flash memory on the Cisco EtherSwitch service module, repeat St ep 1 through Step 6. If the procedure fails again, ensure that yo ...

  • Cisco Systems NME-16ES-1G - page 70

    Cisco EtherSwi tch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Service Module Software 70 Cisco IOS Release 12.2(25)SEC Y ou are prompted for the service module int erface numbe r . Accept the default: Service Module interface number? [0]: Y o u are prompted to confirm the buf fer . A ccept the default : 1k buffer? [confirm ...

  • Cisco Systems NME-16ES-1G - page 71

    Cisco EtherSwitch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Servic e Module Software 71 Cisco IOS Release 12.2(25)SEC Y ou a re prompted for the max retry count. Ac cept the default: Max Retry Count [10]: Y ou are prompted to c onf irm the trans fer to the Cisco EtherSwitch service module: Xmodem send on slot 2 interface ...

  • Cisco Systems NME-16ES-1G - page 72

    Cisco EtherSwi tch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Service Module Software 72 Cisco IOS Release 12.2(25)SEC the flash filesystem, and finish loading the operating system software: flash_init load_helper boot Router: Sample Output for the flash_init Command on the Cisco EtherSwitch Service Mod ule The follo wing ...

  • Cisco Systems NME-16ES-1G - page 73

    Cisco EtherSwitch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Servic e Module Software 73 Cisco IOS Release 12.2(25)SEC SUMMARY STEPS 1. service-module interface slot/port session 2. dir flash: 3. service-module interface slot/port passw ord-reset 4. flash_init 5. (Optio nal) load_helper filesystem:/f ile-url ... 6. ren a m ...

  • Cisco Systems NME-16ES-1G - page 74

    Cisco EtherSwi tch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Service Module Software 74 Cisco IOS Release 12.2(25)SEC Step 6 rename Example: Switch: rename flash: config.text flash: config.text.old Renames the conf iguration f ile to conf ig.te xt.old. • Before continuing to the next command, po wer up any connected sta ...

  • Cisco Systems NME-16ES-1G - page 75

    Cisco EtherSwitch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Servic e Module Software 75 Cisco IOS Release 12.2(25)SEC Step 12 copy running-configuration startup-configuration Example: Switch: copy running-config startup-config Copies the configuration from the running confi guration f ile to the sw itch startup co nfigu r ...

  • Cisco Systems NME-16ES-1G - page 76

    Cisco EtherSwi tch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Service Module Software 76 Cisco IOS Release 12.2(25)SEC Recovering from a Lost or Forgotten Password When Password Recovery Is Disabled This section shows ho w to recov er from a lost or for gotten password when password reco very is disabled. When password rec ...

  • Cisco Systems NME-16ES-1G - page 77

    Cisco EtherSwitch Service Mo dules Feature Guide Troubleshooting the Cisco EtherSwitch Servic e Module Software 77 Cisco IOS Release 12.2(25)SEC DETAILED ST EPS Command or Action Purpose Step 1 service-module interface slot/port password-reset Example: Router# service-module gigabitethernet1/0 password-reset Resets the password on the router . Step ...

  • Cisco Systems NME-16ES-1G - page 78

    Cisco EtherSwi tch Service Mo dules Feature Guide Switch Stack Configuration Scenar ios 78 Cisco IOS Release 12.2(25)SEC Example Sample Output for the set Command The follo wing example sho ws what appears when you enter the set command: Switch: set BAUD=9600 MAC_ADDR=00:00:00:20:30:80 MANUAL_BOOT=yes SDM_TEMPLATE_ID=0 SWITCH_NUMBER=2 SWITCH_PRIORI ...

  • Cisco Systems NME-16ES-1G - page 79

    Cisco EtherSwitch Service Mo dules Feature Guide Switch Stack Config uration Scenarios 79 Cisco IOS Release 12.2(25)SEC T able 4 Switc h Stac k Configur ation Scenar ios Scenario Action Result Stack master election specifically determined by e xisting stack masters Connect two po wered-u p switch stacks through the Cisco StackW ise por ts. Only one ...

  • Cisco Systems NME-16ES-1G - page 80

    Cisco EtherSwi tch Service Mo dules Feature Guide Switch Stack Configuration Scenar ios 80 Cisco IOS Release 12.2(25)SEC Stack master election specifically determined by the cr yptographic IP base image Assuming that all stack members have the same priority v alue: 1. Make sure that one stack member h as the cryptographic IP base image installed an ...

  • Cisco Systems NME-16ES-1G - page 81

    Cisco EtherSwitch Service Mo dules Feature Guide Network Configuration Examp les 81 Cisco IOS Release 12.2(25)SEC Network Configuration Examples This section descri bes network conf iguration co ncepts and includes e xamples of using the Ci sco EtherSwitch service module to cr eate dedicated network se gments and interconnect the segments through F ...

  • Cisco Systems NME-16ES-1G - page 82

    Cisco EtherSwi tch Service Mo dules Feature Guide Network Config uration Exam ples 82 Cisco IOS Release 12.2(25)SEC Bandwidth alone is not the o nly consideration when designin g your networ k. As your netwo rk traf f ic prof iles e volv e, consider pro viding netw ork services that can support application s for voi ce and data integratio n, multim ...

  • Cisco Systems NME-16ES-1G - page 83

    Cisco EtherSwitch Service Mo dules Feature Guide Network Configuration Examp les 83 Cisco IOS Release 12.2(25)SEC Y o u can use the Cisc o EtherSwitch servi ce module s and switch stacks to create the follo wing: • Cost-ef fect i ve wir ing closet ( Figure 8 )—A cost-ef fecti ve way to connec t man y users to the wiring closet is to hav e a swi ...

  • Cisco Systems NME-16ES-1G - page 84

    Cisco EtherSwi tch Service Mo dules Feature Guide Network Config uration Exam ples 84 Cisco IOS Release 12.2(25)SEC • Redundant gigabit backbo ne ( Figure 9 )—Using HSRP , y ou can create backu p paths betw een two Cisco EtherSwitch service modules to en hance netw ork reliab ility and l oad balancing for dif ferent VLANs and subnets. Using HSR ...

  • Cisco Systems NME-16ES-1G - page 85

    Cisco EtherSwitch Service Mo dules Feature Guide Network Configuration Examp les 85 Cisco IOS Release 12.2(25)SEC Figure 1 0 High-P erfor m ance Wir ing Closet Multidwelling Network Using the Cisco EtherSwitch Service Modules A growing se gment of resident ial and comme rcial customers is requ iring high-s peed a ccess to Ethernet metropolitan-area ...

  • Cisco Systems NME-16ES-1G - page 86

    Cisco EtherSwi tch Service Mo dules Feature Guide Network Config uration Exam ples 86 Cisco IOS Release 12.2(25)SEC Figur e 1 1 Cisco EtherS witch Service Modules in a MAN C onfigur ation 121822 Service Pro vider POP Mini-POP Gigabit MAN Residential location Catalyst 3750 StackWise s witch stack Cisco integrated services router with EtherSwitch ser ...

  • Cisco Systems NME-16ES-1G - page 87

    Cisco EtherSwitch Service Mo dules Feature Guide Additional References 87 Cisco IOS Release 12.2(25)SEC Additional References Related Documents Technical Assistance Related T opic Document T itle Hardware installatio n instructions for net work modules Cisco In terface Car ds Instal lation Guide General information about v oice conf igur ation and ...

  • Cisco Systems NME-16ES-1G - page 88

    Cisco EtherSwi tch Service Mo dules Feature Guide Additional References 88 Cisco IOS Release 12.2(25)SEC ...

Manufacturer Cisco Systems Category Switch

Documents that we receive from a manufacturer of a Cisco Systems NME-16ES-1G can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- NME-16ES-1G manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems NME-16ES-1G
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems NME-16ES-1G.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems NME-16ES-1G, service manual, brief instructions and user manuals Cisco Systems NME-16ES-1G. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems NME-16ES-1G.

Similar manuals

A complete manual for the device Cisco Systems NME-16ES-1G, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems NME-16ES-1G by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems NME-16ES-1G.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems NME-16ES-1G - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems NME-16ES-1G, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems NME-16ES-1G, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems NME-16ES-1G - which should help us in our first steps of using Cisco Systems NME-16ES-1G
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems NME-16ES-1G
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems NME-16ES-1G in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems NME-16ES-1G?

Use the form below

If you did not solve your problem by using a manual Cisco Systems NME-16ES-1G, ask a question using the form below. If a user had a similar problem with Cisco Systems NME-16ES-1G it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)