English dropdown-ico

Manual Abus FU9001

101 pages Not applicable
Download

Go to site of 101

Summary
  • Abus FU9001 - page 1

    ABUS WIRELESS ALARM SYSTEM INSTALLATION INSTRUCTION These installation instructions are an impo rtant product acce ssory. They contain important installation and op eration information. Bear this in mind if you pass t he product on to others. Store these installation instruc tions in a safe place for future reference. For a list of contents with pa ...

  • Abus FU9001 - page 2

    ABUS WIRELESS ALARM SYSTEM These installation instructions are publi shed by ABUS Secu rity-Center GmbH & Co. KG, Linker Kreuthwe g 5, D-86444 Affing/Mühlhausen. All rights including transl ation reserved. Re productio ns of all kinds – e.g. photocopy , microfilm, or storage in computer systems – require the express wri tten permission of ...

  • Abus FU9001 - page 3

    Contents Contents ............................................................................................................................... .................................................................. 1-3  Chapter 1 Usage in accord ance with re gulations ................................................................................ ...

  • Abus FU9001 - page 4

    7.5.1 4 4 1 1 Author ity .................................................................................................................... ............................................ 7-58  7.5.2 2 2 Partition ............................................................................................................................... ...... ...

  • Abus FU9001 - page 5

    Chapter 11 Example of an installati on plan .................................................................................... .................................................... 11-96  Appendix A: Event Log Mess ages ................................................................................................ ............................. ...

  • Abus FU9001 - page 6

    Chapter 1 Usage in accordance with regulations The ABUS wireless al arm system is used for protecting flats and homes and small to medium busines s objects. If the wireless alarm system and its accessories are installed prop erly, it alerts you in the case of intr usion, warns you about fires, and calls for help in the event of an emergency. The wi ...

  • Abus FU9001 - page 7

    3-7 Chapter 3 Introduction to the ABUS wireless alarm system Congratulations – you made the right choice! The ABUS wireless alarm system offers you professional technolog y and first-class quality of the specialist for domestic security, pack ed in a moder n, attractive design, and gives yo u a great feeling of safety and security day after day . ...

  • Abus FU9001 - page 8

    3-8 3.2 What is the ABUS wireless alarm syst em? The ABUS w ireless alarm s ystem is an alarm system specially des igned and developed for hous e owners and the owners of small to medium commercial objects. The wireless alarm system ens ures 24-hour security with the help of the wireless sensors an d detectors installed in your propert y. D ependin ...

  • Abus FU9001 - page 9

    3-9 The following graph ic gives you an overvie w of further function properties of your ABUS w ireless al arm syst em : ...

  • Abus FU9001 - page 10

    3-10 3.5 How can the ABUS wireless alarm s ystem be extende d? The ABUS w ireless alarm s ystem is a modular, extend able security system. The following grap hic shows how it can be extended: ...

  • Abus FU9001 - page 11

    3-11 3.6 CE manufacturer’s declaration EG – KONFORMITÄTSERK LÄRUNG EC – DECLARATION OF CONFIRMI TY Wir / We Security-Center GmbH & Co. KG Linker Kreuthweg 5 86444 Mühlhausen (Germany) erklären hiermit, dass das Produkt / here with declares that the product Typ / Type: ABUS Funkalarmanlage auch benannt / also named: RWABUV868xxA* (*xx= ...

  • Abus FU9001 - page 12

    4-12 Chapter 4 Initial considerations Before starting to install your new ABUS wireless alarm system , please take the time to consider the follo wing. You will find helpful tips for planning yo ur system on the accompanying instal l ation DVD. If you cannot find answers to all yo ur questions, p lease contact your specialist dealer, who will be pl ...

  • Abus FU9001 - page 13

    4-13 4.1 What kinds of security are there? In general, there are three different ways of securing an object: External perimeter sur veillance , in which primaril y the endangered areas such as the entrance door, terrace door and cellar doo r as well as ground-floor windows ar e protected by wireless magnet contacts and wireless glass breakage detec ...

  • Abus FU9001 - page 14

    4-14 4.2 What wireless detectors do I need? The type and number of wireless detectors nee ded depends partly on the type of protection and partl y o n the level of security y ou want to achieve. You should therefor e plan your wireless sensors as follo ws: • Consider how an i ntruder can get into yo ur object. It will help if you draw up a plan o ...

  • Abus FU9001 - page 15

    5-15 Chapter 5 Installing the ABUS wireless alarm system Make a sketch of the object or use th e architect’s plans. Ente r the absolutely necess ary wireless detectors defi ned according t o chapter 3. Install the detectors in gr oups. For example: firs t magnetic contacts, then motion s ensors, then smok e detectors. Or divide your object into a ...

  • Abus FU9001 - page 16

    5-16 5.2 How do I install the ABUS wireless alarm system? The ABUS w ireless alarm s ystem is mounted on the wall in three steps. You need a flat screwdriver to ope n the casing. A battery- powered screwdriver is best s uited for drilling the holes for the fixing screws. You can th en use this scre wdriver to screw the fixing screws into the wall. ...

  • Abus FU9001 - page 17

    5-17 5.2.3 Fixing the faceplate Before fixing the faceplate, first read the following sections (up to page 5-20) and then return here. The preced ing sections a re not needed for every installation. When carrying out the follow ing, make sure that t he vo ltage is disconnecte d for all connection work. Both th e power adapter and the standby batter ...

  • Abus FU9001 - page 18

    5-18 5.5 How do I connect the other co ntacts in the ABUS wireless alar m system? 5.5.1 Connecting a wired sounder The ABUS wireless al arm system is fitted with a built-in s ounder. If required, an externa l sounder or piezo sounder can be connected to alert inhabitants and nei ghbours with a loud signal duri ng the alarm. To connect an exter nal ...

  • Abus FU9001 - page 19

    5-19 NOTE: 1. You can connect external equi pment to clamp N.O instead of to clamp N.C . If you connect to clamp NC (normally closed) , the circuit between the system and an exter nal device is closed. If the switch output is acti vated, the system interrupts the ci rcuit and the connected device is switched off. If you connect to clamp NO (normall ...

  • Abus FU9001 - page 20

    5-20 5.6 How are the s tandby batteries us ed? The ABUS alarm system is equ ipped with 6 standby batteries that mai ntain operation during a p ower failure. There are t wo types of battery: Ê Rechargeable : Size AA, 1.2 V DC cells Ê Not rechargeable : Size AA, 1.5 V DC alkaline ! IMPORTA NT NOTE: The batteries supplied by Sec urity-Center are rec ...

  • Abus FU9001 - page 21

    5-21 5.7 What are the effects of the differen t jumper settings? The PC board of the ABUS wi reless alarm system is fitted with internal jumpers. Config ure the jumpers according to the function required as shown in this table: Jumpers on the mainboard Position Function Restores the factory settings. (J9) The J9 jumper of the ABUS wireless al arm s ...

  • Abus FU9001 - page 22

    7-22 Chapter 6 Programming the ABUS wireless alarm system There are several ways of programming your ABUS wi reless alarm system : • At the alarm system using the keypad • At the alarm system using the PC software • Remotely, using a telephone link and PC soft ware Chapter 7 Settings in installer menu This chapter describes the options and f ...

  • Abus FU9001 - page 23

    7-23 7.2 1 1 System Under System , you make settings that affect the entire system. This is an overview of the menu options according to their sequence in the System menu: 1 1 1 1 Timers , page 7-23 1 1 2 2 Control , page 7-25 1 1 3 3 Receiver , page 7-31 1 1 4 4 Clock , page 7-32 1 1 5 5 Labels , page 7-33 1 1 6 6 Tamper Sound , page 7-35 1 1 7 7 ...

  • Abus FU9001 - page 24

    7-24 Timers: Quick-Key Parameter Default Range 1 1 1 1 2 2 Exit/Entry delay 2 Exit and entry delay times of Group 2. Make these settings as for Group 1. 1 1 1 1 2 2 1 1 Ent ry de lay 2 45 seconds 1-255 seconds Entry delay time for Group 2. 1 1 1 1 2 2 2 2 Exit delay 2 45 seconds 1-255 seconds Exit delay time for Group 2. 1 1 1 1 3 3 Bell Timeout 03 ...

  • Abus FU9001 - page 25

    7-25 7.2.2 1 1 2 2 System Control Under System Control , you make settings that control specif ic functions of the complete s ystem. NOTE: Under this menu item, it is important that you press the lozenge button before exiting so that your d a t a i s s a v e d . I f y o u exit the menu by pressing , your settings are lost. To access th e System Co ...

  • Abus FU9001 - page 26

    7-26 System Control: Quick-Key Parameter Default Range 1 1 2 2 06 06 Bell Squawk Y ES YES/NO Y ES: The following sign als are emitted by the e xternal sounder to acknowledge whether you have successfully ac tivated/deactivated the system: • One tone means that the system is activated. • Two tones mean that the system is deactivated. • Four to ...

  • Abus FU9001 - page 27

    7-27 System Control: Quick-Key Parameter Default Range 1 1 2 2 14 14 Audible Jamming NO YES/NO Refers to Jamming Time , which is described on page 7-32. Y ES: If the defined jamming time is reached, the ABUS wireless alar m system activates the sounders. (See Jamming Trouble , pa ge 7-32.) NO: Jamming does not trigger an audible a larm. 1 1 2 2 15 ...

  • Abus FU9001 - page 28

    7-28 System Control: Quick-Key Parameter Default Range 1 1 2 2 21 21 Arm Pre-Wa rning NO YES/NO Y ES: F or the system, or every area for which an automatic activation function was programmed, a warning signal of 255 seconds is generated on the o perating panels and the alarm system prior to activation. During this countdown, you can enter a valid u ...

  • Abus FU9001 - page 29

    7-29 System Control: Quick-Key Parameter Default Range 1 1 2 2 26 26 IMQ Install NO YES/NO Y ES: If a zone is open when the system is activa ted, the system is activated but an alarm is generated when the exit dela y time expires. NO: Open zon es are automatically omitted fo llo wing expiry of the exit delay time. 1 1 2 2 27 27 Grand Master Authori ...

  • Abus FU9001 - page 30

    7-30 System Control: Quick-Key Parameter Default Range 1 1 2 2 31 31 External Bell NO YES/NO Y ES: Select this setting if an external sou nder is connected to the wireless alarm s ystem. The ABUS wireless alarm system monitors the (+) (-) connections as well as BELL TMP and COM and reports faults, events, ala rms and re ports. To avoid a fault in t ...

  • Abus FU9001 - page 31

    7-31 7.2.3 1 1 3 3 Receiver Under Receiver , y ou can make settings that cont rol the radio receiv er of your ABUS wi reless alarm system . To access the Receivers menu option: 1. Select the main menu System as described on page 7-23. 2. In the System menu, press 3 3 to go to the Receivers menu option. You se e the following on the displa y: 3. Sel ...

  • Abus FU9001 - page 32

    7-32 Receiver: Quick-Key Parameter Default Range 1 1 3 3 2 2 Jamming Time No Jamming detection None, 10, 20 or 30 seconds The jamming time specifies the time within o ne minute in which the level of the backgro und noise can be above the value measur ed under “Calibration” (or above the manually set value). NOTE: A fault is displayed only if th ...

  • Abus FU9001 - page 33

    7-33 7.2.5 1 1 5 5 Labels Under System Labe l , you name the system and areas 1, 2 and 3, and change d efault names. To enter a new name: Use the buttons of your ABUS w ireless alarm system to enter the letter s as shown in the table belo w. When you press a specific button, you scroll b ackwards and forwards through th e characters. The ABUS w ire ...

  • Abus FU9001 - page 34

    7-34 To access th e System Lab el menu: 1. Select the main menu System as described on pa ge 7-23. 2. In the System menu, press 5 5 to get to the System Label menu option. You see the following on the display: 3. Select and configure the settings in the Syst em Label menu as follows: System Label: Quick-Key Menu option De fault Selection 1 1 5 5 1 ...

  • Abus FU9001 - page 35

    7-35 7.2.6 1 1 6 6 Tamper Sound In the Tamper Sound menu, you can define the sounds generated by the ABUS wireless alarm s ystem follo wing a tamper in a zone, the ABUS wireless alarm centre housing, the wireless operating pane l, or any other device. You c an also adjust the sounder vol u me for alarms and their acknowledgement. To access the Tamp ...

  • Abus FU9001 - page 36

    7-36 7.2.7 1 1 7 7 System Default Jump er In the Default Jumper menu, you enable or disable a soft ware factory reset via the J9 jumper. To access th e Default Ju mper menu: 1. Select the main menu System as described on pa ge 7-23. 2. In the System menu, press 7 7 to access the Default Jumper menu option. You see the follo wing on the display: 3. ...

  • Abus FU9001 - page 37

    7-37 7.3 2 2 Zones The Zones menu enables you to train wireles s detectors for the system, program zone types, and define zone dep endencies. This is an overview of the menu options according to their sequence in the Zones menu: 2 2 1 1 Allocation , page 7-37 2 2 2 2 Parameters , page 7-3 8 2 2 3 3 Testing , page 7-48 2 2 4 4 Editing , page 7-49 2 ...

  • Abus FU9001 - page 38

    7-38 2 2 1 1 ZZ ZZ 3 3 Delete Deletes detectors. Confirm deletion with [Y] YES or [N] NO . To change the display, press . 2 2 1 1 ZZ ZZ 4 4 Supervision Select whether a zone is to be monitored for regular rep orting by the detectors to the alarm system. Set the monitoring time in the System menu under Time rs . If surveillance is active for the det ...

  • Abus FU9001 - page 39

    7-39 Parameter Quick-Key Parameter Default Range IMPORTANT INFORMATION: • If you selected one by one to program the zones individuall y, you are guided step b y step through the programming points for the zones. • T o save settings for the zone, you have to work through all menu o ptions. If you exit programming early by pressing the star butto ...

  • Abus FU9001 - page 40

    7-40 2 2 2 2 2 2 Zone Label Under Zone label , y ou can define or edit a name up to 15 characters l ong for each zone. Under Parameters , press 2 2 to access the zone label menu option. You see the following on the display: P ress to name Zone 01 or enter a different zone n umber. You see the following o n the display: Edit the zone name as describ ...

  • Abus FU9001 - page 41

    7-41 2 2 2 2 4 4 Zone Type When a detector triggers, it always sends a sign al to the alarm system. For example: A motion sensor reacts to movem ent, a smoke detector to smoke, etc. So it is important to tell the system HOW and WHEN it is to react to a signal from a detector. Under Zone type , you can program the behaviour of the alarm system when ...

  • Abus FU9001 - page 42

    7-42 2 2 2 2 4 4 ZZ ZZ + 03 03 Exit(OP)/Entry Default for zone 1 A rmed/internal Zone type Exit(OP)/Entry behaves like zone t ype Exit/Entry 1 except that the zone does not have to be closed at the moment of activation. However, the zone must be closed before the exit delay time expires, or other wise there is an alarm. This zone type is usually as ...

  • Abus FU9001 - page 43

    7-43 2 2 2 2 4 4 ZZ ZZ + 03 03 Exit(OP)/Entry Default for zone 1 A rmed/internal Zone type Exit(OP)/Entry behaves like zone t ype Exit/Entry 1 except that the zone does not have to be closed at the moment of activation. However, the zone must be closed before the exit delay time expires, or other wise there is an alarm. This zone type is usually as ...

  • Abus FU9001 - page 44

    7-44 2 2 2 2 4 4 ZZ ZZ + 10 10 I+Instant (Interior+Instant) A rmed The I+Instan t zone type is similar to zone type Instant. However, this zone type is not monitored for an internally activated system. 2 2 2 2 4 4 ZZ ZZ + 11 11 UO Trigger A rmed The UO Trigger zone t ype controls a switch output whet her the system is active or inactive. For exampl ...

  • Abus FU9001 - page 45

    7-45 2 2 2 2 4 4 ZZ ZZ + 18 18 Exit Termination A zone with the Exit Termination zone type behaves like a zone with the Exit(OP)/Entry zone type. However, the difference is that an exit delay time is ended immedi ately if this zone is opened or closed during the e xit delay time. When you enter the protected area, the e ntry delay time of Group 1 s ...

  • Abus FU9001 - page 46

    7-46 2 2 2 2 4 4 ZZ ZZ + 18 18 Exit Termination A zone with the Exit Termination zone type behaves like a zone with the Exit(OP)/Entry zone type. However, the difference is that an exit delay time is ended immedi ately if this zone is opened or closed during the e xit delay time. When you enter the protected area, the e ntry delay time of Group 1 s ...

  • Abus FU9001 - page 47

    7-47 2 2 2 2 5 5 Zone Sound Under Zone sound , you can, for each zone, define the alarm signal individua lly that is triggered when the alarm system is active. 1. Under Parameters , press 5 5 to access the Zone sound menu option. You see the following on the display: 2. Enter a two-digit number and press . 3. Select and configure a zone signa l for ...

  • Abus FU9001 - page 48

    7-48 2 2 2 2 6 6 Force A rm The Force Arm setting for a zone enables the s ystem to be activated even if one or more zones are open, provided thes e zones were programmed with this setting. • If such a zone is open, the “ready” system LED flashes. • After the system is activat ed, all open zones programmed a s Force A rm are automatically e ...

  • Abus FU9001 - page 49

    7-49 2 2 3 3 2 2 Soak Test Some wireless detectors tend to trigger alarms more than others. T he Soak Test was developed to test these detectors ov er a longer peri od without triggering an alarm. Up to 8 zones can be programmed for the Soak T est. A zone programmed for the Soak Test is omitted for 14 days while the alarm system is active. If no al ...

  • Abus FU9001 - page 50

    7-50 Editing Quick-Key Parameter 2 2 4 4 1 1 Copy to a zone Copies all settings programmed for a zon e (except the zone name). 1. Press 1 1 . You see the following on the displ ay: 2. Press the number buttons 1 to 9 to select the zone you want to copy and press or to move the cursor. Press 1 to 9 again to select the zone to which you want to copy. ...

  • Abus FU9001 - page 51

    7-51 7.3.5 2 2 5 5 Cross Zone Default: No cross-zone dependenc y Cross-zone dependency is an idea l function for making a system safer against false alarm s. Using cross-zone depende ncy, two zon es have to trigger an alarm within a specific period and in a defined or un defined sequence before the alarm system generates an a larm. NOTE: The ABUS w ...

  • Abus FU9001 - page 52

    7-52 7.4 3 3 Outputs Under Outputs , you program the relay and transistor output s of the system. You link different system event s to the activation of the outputs. The following is an overvie w of the m enu options according to their seque nce in the Outputs menu: 3 3 1 1 Define, page 7-52 3 3 2 2 Output A , page 7-57 3 3 3 3 Output B , page 7-57 ...

  • Abus FU9001 - page 53

    7-53 3 3 1 1 UO UO 1 1 02 02 No Telephone Line The switch output is activated if a break in th e telephone lin e is detected. It is deactivated after the telephone line fault is removed. 3 3 1 1 UO UO 1 1 03 03 Communication Failure The switch output is activated if no contact to the command centre can be establ ished. It is deactivated after a suc ...

  • Abus FU9001 - page 54

    7-54 3 3 1 1 UO UO 2 2 06 06 Panic Follo w The switch output is activated if a panic al ar m is triggered in the selected area(s) or if the (PANIC) alarm buttons are pressed simultaneousl y. 3 3 1 1 UO UO 2 2 07 07 Special Emergency Follow The switch output is activated if a medi cal emerge ncy alarm is triggered in the selected area(s) or if the a ...

  • Abus FU9001 - page 55

    7-55 3 3 1 1 UO UO 2 2 18 18 Bell Stay Off The switch output is activated as follo ws: • If the system is activated externally (AWAY), the switch output is activated as soon as the sounder is triggered in the selected ar ea. • If the system is activated internally (STAY), the s witch output is not activated if the sounder is tr iggered in the s ...

  • Abus FU9001 - page 56

    7-56 Output mode An output mode has to be set for every output. This t able gives an overview of t he different output modes: Outputs Quick-Key Parameter Default Range 1 1 Pulse N/C 05 seconds 01-90 seconds The output is closed in non-activated state. Once activa ted, it remains open unti l the set time has elapsed and then resets itself auto matic ...

  • Abus FU9001 - page 57

    7-57 Activation/Deactivation If the switch output follows more than one area or zone, you can use different patterns for activatin g and deactivating the swi tch output. ALL or AN Y . All : ALL areas (or zones) programmed for this s witch output must be tr iggered in order to activate the output. On the other hand, al l areas or zones must be inact ...

  • Abus FU9001 - page 58

    7-58 7.5 4 4 Codes Under Codes , you can define user and installer Cod e s, define authorities, and assign ar eas. The ABUS wireless al arm system also has the following Codes. Ê Grand Master Code: Used b y the system owner. This Code has authority over all others and can on ly be changed but not deleted. The default is: [1][2][3][4] . Ê Installe ...

  • Abus FU9001 - page 59

    7-59 Authority Leve ls The Authority Lev els menu option contains settings for the following authorities: Grand Master: There is only one Grand Mast er in the system. The Grand Master can car ry out all available user functio ns. The Grand Master code is defined as PIN code user 00. NOTE: Under System Control , you can define that the Grand Mast er ...

  • Abus FU9001 - page 60

    7-60 7.5.2 4 4 2 2 Partition Default: Partition 1 Under Partition , you assign to user PINs partitions for which you hav e aut hority. The Grand Master is authorised in all partitions. To access th e Partition menu: 1. Select the Codes menu as described on page 7-57. 2. Under Codes , press 2 2 to access the Partition menu option. 3. Enter the respe ...

  • Abus FU9001 - page 61

    7-61 7.5.4 4 4 4 4 Installer Default : 0133 With the installer PIN, you have access to the installer menu and thus the author ity to change all system parameters. T he insta ller code defined in the factory is: [0][1][3][3] ABUS strongly recommends chan ging the PIN defined in the factory. To access th e Installer men u: 1. Select the Code Maintena ...

  • Abus FU9001 - page 62

    7-62 7.5.6 4 4 6 6 Code Length Default: four digits Under Code Length , you can change the number of digits used (4 or 6) for the Grand Master , the Manager and the Master . All other PIN codes (user, Arm Only and maid) use one to six digits. To access the Code Length menu: 1. Select the Code Maintenance menu as described on page 7-57. 2. Under Cod ...

  • Abus FU9001 - page 63

    7-63 7.6 5 5 Dialer The Dialer menu enables you to transmit alarms as voice text by teleph one. In this menu, you als o make the settings necessary for programming the system via a modem. Some of the options in this menu cannot be selected since they are not active i n this versi on. You can access the follo wing submenus: 5 5 4 4 UD Telephone numb ...

  • Abus FU9001 - page 64

    7-64 Access Code and ID Quick-Key Parameter Default 5 5 5 5 1 1 Access code 5678 Defines an access code for remote program ming. The four-digit access code in the system and the software must be identical. 1. Enter a four-digit access code. This code is stored in the ABUS w ireless alarm system . 2. You have to enter the same code in the up/do wnlo ...

  • Abus FU9001 - page 65

    7-65 Controls Quick-Key Menu option Default 5 5 6 6 02 02 FM Enable NO Y ES: Enables FM (= Follow Me) transmission. (See also Follow Me, page 7-68.) Enable this option to transmit alarms as voice messag es by telephone. Disabl e this option if the system has no telephone conn ection, since other wise a telephone error is reported. NO: No FM transmi ...

  • Abus FU9001 - page 66

    7-66 Controls Quick-Key Menu option Default 5 5 6 6 10 10 Answering Machine Override YES Y ES: Answering machine override i s activated. • The upload/download soft ware calls the ABUS alarm syst em . • The software hangs up following a ring by th e U/D user. • The software calls again within one minute. • The ABUS wireless al arm system is ...

  • Abus FU9001 - page 67

    7-67 Dialer: Para meter Quick-Key Parameter Default Range 5 5 7 7 4 4 1 1 Wait 6 seconds Press 1 1 follow ed by . 5 5 7 7 4 4 2 2 Wait 9 seconds Press 2 2 follow ed by . 5 5 7 7 5 5 Redial wait 30 seconds 30 or 60 seconds The number of seconds bet ween a redial of the same number. 5 5 7 7 5 5 1 1 Wait 30 sec onds Press 1 1 follow ed by . 5 5 7 7 5 ...

  • Abus FU9001 - page 68

    7-68 Dialer: Para meter Quick-Key Parameter Default Range 5 5 7 7 8 8 Swinger Limit 00 00 to 15 The Alarm Limit option is provi ded to prevent multiple triggeri ng on a zone within the activated time. Setting 01: A triggered zone is not transmitted aga in if this has already happened. If you raise the limit, t he alarm is transmitted accordin g to ...

  • Abus FU9001 - page 69

    7-69 7.6.5 5 5 9 9 Follow Me (FM) Under this menu option, you define the for warding of an alarm as a voice text to a telephone or a secur ity service. In the even t of an alarm, the ABUS wireless alarm system c alls the programmed F M numbers and transmits the alarm message according to the eve nt. There are two variants of this FM feature: • St ...

  • Abus FU9001 - page 70

    7-70 Follow-Me Quick-Key Parameter Default 5 5 9 9 2 2 Events restore Defines whether a new call is made if t he event (from section 5.9.1) is res et. Press or to select an event and press to select whether this event is to be transmitted by phone: [Y] YES or [N] NO . [01] Intruder Y [02] Tamper N [03] A C Off N [04] Wireless Lost N [05] Wireless L ...

  • Abus FU9001 - page 71

    7-71 7.7 7 7 Key-fobs Under key-fobs , you learn how to train up to eight 4-button ke y-fobs with rolling code to work with the ABUS wi reless alarm system . With the wireless key-fob/remote control, you can activat e/deac tivate the system, trigger a panic a larm, and control a switch o utput. The following is an overvie w of the menu options acco ...

  • Abus FU9001 - page 72

    7-72 7.7.2 7 7 2 2 Parameters Under Parameters , you pr ogram the function and the keys of the remote c ontrol. The four buttons of the remote contro l can be adapted to individual require ments. To access th e Parameters menu: 1. Select the Key-fob menu as described on page 8-68. 2. Under Key-fob , press 2 2 to access the Parameters menu option. Y ...

  • Abus FU9001 - page 73

    7-73 8. You see the following on the d isplay: 9. For button 3 (small button), you can ch oos e between the following function s:  None: T he button is not activated (default).  Panic: The button triggers a panic alarm.  Utility Output: The button activates a utility output. If you select the switch output function and confirm it with , yo ...

  • Abus FU9001 - page 74

    7-74 7.8 8 8 Keypads Under Keypads , you can assign two operating pa nels to the ABUS wireless alarm s ystem . T he following is an overvie w of the menu options according to their seq uence in the Keypads menu: 8 8 1 1 Allocation , page 7-77 8 8 2 2 Communication test, page 7 -77 To access th e Keypad s menu: • In the installer menu, select 8 8 ...

  • Abus FU9001 - page 75

    7-75 7.8.2 8 8 2 2 Communication Test Under Communication Test you test the radio communication bet ween your wireless operating panel and the system. To access th e Communic ation test menu : 1. Select the Keypads menu as described above. 2. Under Keypads , press 2 2 to access the Communication test menu o ption. You see the following on the displ ...

  • Abus FU9001 - page 76

    7-76 7.9.1 9 9 1 1 A llocation Here you can allocat e a new sounder to your s ystem. To access th e Allocation menu: 1. Select the Siren menu. 2. Under Siren , press 1 1 to access the Allocation menu option. You see the following on the displa y: 3. Press to select the type of sounder you want to train. Two types are available: • INWS1 : internal ...

  • Abus FU9001 - page 77

    7-77 7.9.2 9 9 2 2 Parameter Under this menu option, you c an change the sounder settings. You can chang e the following settings: • Volume • Flash frequency (extern al sounders only) To access th e Parameter menu: 1. Select the Siren menu. 2. Under Sirene , press 2 2 to access the Parameter menu option. You see the follo wing on the display: 3 ...

  • Abus FU9001 - page 78

    7-78 7.9.3 9 9 3 3 Communication test Under communi cation test you test the radio communicati on bet ween your soun der and the system. To access th e communicatio n test menu: 1. Select the Siren menu as described above. 2. Under Siren , press 3 3 to access the communication test menu opti on. You see the following on the display: 3. Confirm with ...

  • Abus FU9001 - page 79

    7-79 7.9.5 9 9 5 5 Tamper Mute Under Tamper Mute , you can deactivate the tamper function of the sounder for the current programming process. This enab les you to open the sounder without triggering a tamper alarm. E nable this function if you want to open the sounder case, for example to change the batteries. To access Ta mper Mute menu : 1. Selec ...

  • Abus FU9001 - page 80

    7-80 7.10 0 0 Exit Programming Under Exit Programming , all your settings in the installer menu are save d and you exit the installer men u. Important: The settings you make in the installer me nu are not saved until you exit the installer menu correctly. NOTES: To be able to exit the installer menu, the J9 jumper plug must be plugge d on to one pi ...

  • Abus FU9001 - page 81

    8-81 Chapter 8 Programming within the user programming menu This chapter explains an im portant menu option in the user menu. T his menu option is for programming voice messages and conduc ting a walk t est . 8.1 Programming voice messag es Your ABUS wireless alarm s ystem can issue system events locall y and by telephone using voice messages. T hi ...

  • Abus FU9001 - page 82

    8-82 8.1.1 7 7 1 1 Message structure Under Message structure , you define the seque nce in which the voice messages ar e transmitted. To define a messag e structure: 1. Select the voice message menu as descr ibed above. 2. In the voice message menu, press 1 1 to access the message structure me nu option. You see the follo wing on the display: 3. Pr ...

  • Abus FU9001 - page 83

    8-83 8.1.2 7 7 2 2 Voice message labels Under voice message labels , you define na mes for zones, partitions, utility output s an d macro keys, and you find out ho w to play and record common messages. To define a voice message: 1. Select the message label menu. 2. In the voice message menu, press 2 2 to access the message label menu option. You se ...

  • Abus FU9001 - page 84

    8-84 Voice message: messag e name Quick-Key Parameter Default Range 7 7 2 2 2 2 Zone message Press 2 2 . You see the following on the displ ay: Press or to select a zone and then press . The following options are ava ilable:  Press 1 1 to play the zone announcement. You hear the announce ment over the system loudspeaker. The fa ctory default for ...

  • Abus FU9001 - page 85

    8-85 Message Labels Quick-Key Parameter Default Range 7 7 2 2 3 3 Partition Message Press 3 3 . You see the following on the displ ay: Press or to select a partition and then press . The following options are ava ilable:  Press 1 1 to play the partition announcement. You hear the announcement over the system louds peaker. Press 2 2 to record a n ...

  • Abus FU9001 - page 86

    8-86 Message Labels Quick-Key Parameter Default Range 7 7 2 2 4 4 Utility output message NOTE: The switch output must be defined as an FM code in order to be able to all ocate a voice message to it. See also Follow User Code. Press 4 4 . You see the following on the displ ay: Press or to select a switch output and then press . You see the fol lowin ...

  • Abus FU9001 - page 87

    8-87 8.1.3 7 7 3 3 Test Message Under Test Message , you c an test recorded and assigned voice announcements. To conduct a Test message: 1. Select the Voice message menu. 2. In the Voice message menu, press 3 3 to access the Test Message menu option. You see th e following on the display: 3. Conduct the test locally or by telep hone as follows: Voi ...

  • Abus FU9001 - page 88

    8-88 8.1.4 7 7 4 4 Local A nnouncement Me ssages Under this menu option, you adapt loc al vo ice announcements to your requirements. To activate/deac tivate local voice announcements : 1. Select the Voice Message menu. 2. In the Voice Message menu, press 4 4 to access the Announce msg. menu option. You see the following on the display: 3. Press or ...

  • Abus FU9001 - page 89

    8-89 8.2 Walk test Under the Walk test menu option, you can test your i nstallation. When the system is in walk-test mode, you can trigger detectors without setting off an alarm. The walk test mode can be started in t wo ways: • Installer PIN • Grand Master PIN NOTE: The difference bet ween a walk test started with an installer PIN and a walk t ...

  • Abus FU9001 - page 90

    9-90 Chapter 9 Accessories for your ABUS w ireless alarm system The following is a list of accessories for your ABUS wireless alarm system . Wireless motion detector The wireless motion detector is used for prot ecting entire rooms. With its infrared element, it can monitor an are a of 15 x 15m wi th a n angle of vision of 90°. Pet-immune wireless ...

  • Abus FU9001 - page 91

    10-91 Chapter 10 Brief guide This chapter explains the installation st eps sho wn on the DVD for the ABUS wireless alarm package inclu ding a smoke detector. A fter you have taken the installatio n steps shown in this guide, yo ur ABUS wireless alarm system is completely operational. 10.1 Hardware installatio n 10.1.1 ABUS wireless alarm syst em ? ...

  • Abus FU9001 - page 92

    10-92 10.2 Training the detectors for the ABUS wireless alarm system 10.2.1 Installer menu of th e ABUS wireless alarm system • First press the star button, followed by 9, followed by 1. 9 9 1 1 • You are asked to enter the installer PIN co de for the installer menu. The default setting is 013 3 . Enter this installer PIN and confirm your input ...

  • Abus FU9001 - page 93

    10-93 10.2.3 Programming zones You do not have to program the zones for the detectors in yo ur package. They are already progr ammed for you as follows: No. Zone name Zone ty pe Detector type Partition Message 1 Zone 1 Entry(o)Exit (30sec/30sec) Wireless opening contact detector 1 Entrance door 2 Zone 2 Instant W ireless motion sensor 1 Living room ...

  • Abus FU9001 - page 94

    10-94 10.4 Exiting the installer menu All wireless components in the package ar e now trained. Your ABUS w ireless alarm system is almost ready for operation. You just have to enter the date and time and an alar m telephone number for voice text transmis sion in the event of an alarm. First, exit the installer menu. Proceed as follows: • Press 0 ...

  • Abus FU9001 - page 95

    10-95 • Confirm the menu option phone num ber 1 with the Enter button. • On the system keypad, enter the number with local area co de and if necessary a zero for obtainin g a dial tone. To program a dial pause, enter A . You program the A w ith the button. Press this button repeatedly until an A appears. • To change the entered num ber, press ...

  • Abus FU9001 - page 96

    11-96 Chapter 11 Example of an installation plan The following table provides an overvi ew of the in formation your installation pla n should contain: Partition Zone number Detector Zone type Name 1 1 Door and window contacts Entry/exit MC front door 1 2 Door and window contacts Entry/exit MC terrace door 1 3 Motion detector Instant MS living room ...

  • Abus FU9001 - page 97

    11-97 Partition Zone number Detector Zone type Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 ...

  • Abus FU9001 - page 98

    11-98 Appendix A: Event Log Messages This appendix prov ides descriptions of all the Event Log messages (ver 1.2xx) EVENT MESSAGE DESCRIPTION Activate UO=X UO XX activation Actv UO=XX WB=YY UO XX is activated from key-fob YY Alarm Z=XXX Alarm in zone No. XXX Alarm abort P=X Alarm aborted on Partition X Arm:P=X WB=YY Partition X armed by wireless ke ...

  • Abus FU9001 - page 99

    11-99 EVENT MESSAGE DESCRIPTION Foil Z=XXX Trouble in foil (Day) zone No. XX X Forced P=X Partition X is force armed Found Z=XXX Wireless zone found, z one No. XXX Func=XX C=YY Quick key function XX by user YY Home:P=X C=YY Partition X is armed in Stay(Home) mode by user YY Home:P=X WB=YY Partition X is armed in Stay(Home) from key-fob YY Jamming r ...

  • Abus FU9001 - page 100

    11-100 EVENT MESSAGE DESCRIPTION Restore Z=XXX Alarm restore in zone No. X XX Remote arm:P=X Partition X armed from the UD software Rmt disarm:P=X Partition X disarmed from the UD software Spec. KP=XX Spec ial alarm from wireless ke ypad XX (keys 7 & 8) Spec. main KP Special alarm from the WisDom emergency k eys Soak fail Z=XXX Zone XXX has fai ...

  • Abus FU9001 - page 101

    11-101 ...

Manufacturer Abus Category Security access control system

Documents that we receive from a manufacturer of a Abus FU9001 can be divided into several groups. They are, among others:
- Abus technical drawings
- FU9001 manuals
- Abus product data sheets
- information booklets
- or energy labels Abus FU9001
All of them are important, but the most important information from the point of view of use of the device are in the user manual Abus FU9001.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Abus FU9001, service manual, brief instructions and user manuals Abus FU9001. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Abus FU9001.

Similar manuals

A complete manual for the device Abus FU9001, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Abus FU9001 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Abus FU9001.

A complete Abus manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Abus FU9001 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Abus FU9001, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Abus FU9001, that we can find in the current document
3. Tips how to use the basic functions of the device Abus FU9001 - which should help us in our first steps of using Abus FU9001
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Abus FU9001
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Abus FU9001 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Abus FU9001?

Use the form below

If you did not solve your problem by using a manual Abus FU9001, ask a question using the form below. If a user had a similar problem with Abus FU9001 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)