English dropdown-ico

Manual Chamberlain ATS 2113X

32 pages 0.97 mb
Download

Go to site of 32

Summary
  • Chamberlain ATS 2113X - page 1

    Owner’s Manual Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System ■ ® is connected and properly aligned. Periodic checks of the opener are required to ensure safe operation. ■ The model number label is loca ...

  • Chamberlain ATS 2113X - page 2

    2 Introduction 2-5 Safety symbol and signal word review . . . . . . . . . . . . . . . . . . . . .2 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Chamberlain ATS 2113X - page 3

    3 Preparing your garage door Before you begin: Disable locks. • Remove any ropes connected to garage door. • Complete the following test to make sure your garage door is • balanced and is not sticking or binding: Lift the door about halfway as shown. Release the door. If 1. balanced, it should stay in place, supported entirely by its springs. ...

  • Chamberlain ATS 2113X - page 4

    4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 18 for details. Support bracket & fastening hardware is required. See page 11. — — — — — — — — Header Wall Safety Reversing Sensor Gap between floor and bott ...

  • Chamberlain ATS 2113X - page 5

    5 Straight Door Arm Door Bracket Plate Door Bracket Safety Labels and Literature "C" Wrap (2) 2 -Conductor Bell Wire White & White/Red Curved Door Arm Rail Styrofoam Chain Pulley Bracket Trolley Chain Safety Reversing Sensor Mounting Bracket With Slot (2) Safety Reversing Sensor Mounting Bracket With Square Holes (2) Mounting Hardware ...

  • Chamberlain ATS 2113X - page 6

    6 ASSEMBLY STEP 1 Attach the Rail to the Motor Unit To avoid installation difficulties, do not run the garage door opener until instructed to do so. Place the opener on packing material to protect the cover. • Remove the (2) 5/16"-18x1/2" washered bolts mounted in the • top of the motor unit. Position rail at a 45˚ angle to opener so ...

  • Chamberlain ATS 2113X - page 7

    7 ASSEMBLY STEP 3 Tighten the Chain Spin the inner nut and lock washer down the threaded shaft, • away from the trolley. To tighten the chain, turn outer nut in the direction shown. • As you turn the nut, keep the chain from twisting. When the chain is approximately 1/2" (1.27 cm) above the base • of the rail at its midpoint, re-tighten ...

  • Chamberlain ATS 2113X - page 8

    8 INSTALLATION STEP 1 Determine the Header Bracket Location Close the door and mark the inside vertical centerline of the 1. garage door. Extend the line onto the header wall above the door. 2. You can fasten the header bracket within 4 feet (1.22 m) of the left or right of the door center only if a torsion spring or center bearing plate is in the ...

  • Chamberlain ATS 2113X - page 9

    9 INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. DO NOT install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BR ...

  • Chamberlain ATS 2113X - page 10

    10 Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Chain Pulley Bracket Temporary Support Header Wall Garage Door Rail Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Chain Pulley Bracket Rail HARDWARE SHOWN ACTUAL SIZE INSTALLATION STEP 3 Attach the Rail to the Header Bracket Position the opener on the garage floor be ...

  • Chamberlain ATS 2113X - page 11

    11 INSTALLATION STEP 4 Position the Opener SECTIONAL DOOR ONLY A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. Raise the opener onto a stepladder. You will need help at this • point if the ladder is not tall enough. Open the door all the way and place a 2x4 laid flat on the top • section beneath the rail. Trolley Relea ...

  • Chamberlain ATS 2113X - page 12

    12 Drywall Anchors Insulated Staples Screw 6ABx1-1/2" Lighted Door Control Button HARDWARE SHOWN ACTUAL SIZE To prevent possible SERIOUS INJURY or DEATH from electrocution: Be sure power is not connected BEFORE installing door • control. Connect ONLY to 24 VOLT low voltage wires. • To prevent possible SERIOUS INJURY or DEATH from a closing ...

  • Chamberlain ATS 2113X - page 13

    13 INSTALLATION STEP 7 Install the Light Install a 75 watt maximum light bulb in the socket. The light • will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the light will turn OFF. If the bulb burns out prematurely due to vibration, replace with • a “Garage Door Opener” bulb. NOTE: Use only standard li ...

  • Chamberlain ATS 2113X - page 14

    14 INSTALLATION STEP 9 Electrical Requirements To avoid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contac ...

  • Chamberlain ATS 2113X - page 15

    15 Invisible Light Beam Protection Area Safety Reversing Sensor 6" (15 cm) max. above floor Safety Reversing Sensor 6" (15 cm) max. above floor Facing the door from inside the garage INSTALLATION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will m ...

  • Chamberlain ATS 2113X - page 16

    16 Inside Garage Wall “C” Shaped Wrap Mounting Bracket with Square Holes 1/4-20x1/2" Carriage Bolts 1/4"-20 Lock Nuts Drill 3/8" Holes Garage Door Track Figure 3 Garage DOOR Track Installation Mounting Bracket With Square Holes #10-32x3/8" Screws “C” Wrap #10-32 Lock Nuts Figure 1 Garage WALL or DOOR Track Installation M ...

  • Chamberlain ATS 2113X - page 17

    17 Hex Bolt 1/4-20 x 1-1/2" "C" Wrap Sensor with Wire Wing Nut Indicator Light Figure 6 Invisible Light Beam Protection Area Safety Reversing Sensor Safety Reversing Sensor Connect Wire to Opener Terminals Bell Wire Bell Wire Finished Ceiling Sensor Connections Wall Control Connections (dotted line) OPENER TERMINAL SCREWS 1 2 3 Figur ...

  • Chamberlain ATS 2113X - page 18

    18 HARDWARE SHOWN ACTUAL SIZE Figure 2 Figure 1 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. INSTALLATION STEP 11 Fasten the Door Bracket A horizontal brace should be long enough to be secured to 2 vertical supports. A ver ...

  • Chamberlain ATS 2113X - page 19

    19 INSTALLATION STEP 12 Connect Door Arm to Trolley SECTIONAL DOORS ONLY Make sure garage door is fully closed. Pull the emergency • release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2" (5 cm) as shown in Figures 1, 2 and 3. Figure 1: • Fasten straight door arm se ...

  • Chamberlain ATS 2113X - page 20

    20 ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener, press the Door Control push bar. Run the opener through a complete travel cycle. Does the door open and close completely? • Does the door stay closed and not reverse uni ...

  • Chamberlain ATS 2113X - page 21

    21 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door. If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weathe ...

  • Chamberlain ATS 2113X - page 22

    22 ADJUSTMENT STEP 3 Test the Safety Reversal System TEST With the door fully open, place a 1-1/2" (3.8 cm) board (or a • 2x4 laid flat) on the floor, centered under the garage door. Operate the door in the down direction. The door must reverse • on striking the obstruction. ADJUST If the door stops on the obstruction, it is not traveling ...

  • Chamberlain ATS 2113X - page 23

    23 OPERATION Using Your Garage Door Opener Your opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. Activate your opener with any of the following: The hand-held Remote Control: • Hold the large push button down until the door starts to move. The wall-mounted Door Control: • Hold th ...

  • Chamberlain ATS 2113X - page 24

    24 To Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually. To reconnect the door to the opener, press the door control push bar. The lockout feature prevents the trolley from reconnecting automatically. Pull the emergency release handle down and back (toward the op ...

  • Chamberlain ATS 2113X - page 25

    25 Having a Problem? The opener doesn’t operate from either the Door Control or 1. the remote control: Does the opener have electric power? Plug a lamp into the • outlet. If it doesn’t light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) Have you disabled all door locks? Review installation • ins ...

  • Chamberlain ATS 2113X - page 26

    26 The 300 Series remote control works only with door openers and light controls having a purple “Learn” button. Programming instructions are described and illustrated below. The additional push buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those accesso ...

  • Chamberlain ATS 2113X - page 27

    27 Press and release the “learn” button on 1. motor unit. The learn indicator light will glow steadily for 30 seconds. Within 30 seconds, enter a four digit 2. personal identification number (PIN) of your choice on the keypad. Then press and hold the enter button. Release the button when the motor unit 3. lights blink. It has learned the code. ...

  • Chamberlain ATS 2113X - page 28

    28 Multi-Function Door Control (Optional) OPERATION OF THE MULTI-FUNCTION DOOR CONTROL Press the push button to open or close the door. Press again to reverse the door during the closing cycle or to stop the door while it’s opening. Light feature Press the Light button to turn the opener light on or off. It will not control the opener lights when ...

  • Chamberlain ATS 2113X - page 29

    29 6 UP CEILING MOUNT ONLY 10 1 NOTICE 3 5 4 9 8 11 12 2 7 2 1 3 4 5 Installation Parts REPAIR PARTS Rail Assembly Parts KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A2780 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 CD1008 8 Foot (2.44 m) Rail Assy. CD1010 10 Foot (3.05 m) Rail Assy. CD1012 12 Foot (3.66 m) Rail Assy. CD ...

  • Chamberlain ATS 2113X - page 30

    30 Motor Unit Assembly Parts 9 7 12 13 14 15 18 4 8 11 17 10 16 3 5 6 18 15   Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 1 2 KEY PART NO. NO. DESCRIPTION 41C5069 Rail support bracket assembly kit 1. 41B4569 Pulley (Chain) 2. 41A5668 Gear and sprocket assembly. 3. Compl ...

  • Chamberlain ATS 2113X - page 31

    31 LOCK LI GH T ACCESSORIES 370LM CD1008 1702LM Outside Quick Release: Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley. 8 Foot (2.44 m) Complete Rail: To allow an 8 foot (2.44 m) door to open fully. 10 Foot (3.05 m) Complete Rail: To allow a 10 foot (3.05 m) door to open ...

  • Chamberlain ATS 2113X - page 32

    © 2010, The Chamberlain Group, Inc. 114A3155E All Rights Reserved LIFTMASTER ® SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Std. Time) 6:00 A.M. TO 7:00 P.M. - Monday through Friday ...

Manufacturer Chamberlain Category Garage Door Opener

Documents that we receive from a manufacturer of a Chamberlain ATS 2113X can be divided into several groups. They are, among others:
- Chamberlain technical drawings
- ATS 2113X manuals
- Chamberlain product data sheets
- information booklets
- or energy labels Chamberlain ATS 2113X
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chamberlain ATS 2113X.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chamberlain ATS 2113X, service manual, brief instructions and user manuals Chamberlain ATS 2113X. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chamberlain ATS 2113X.

Similar manuals

A complete manual for the device Chamberlain ATS 2113X, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chamberlain ATS 2113X by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chamberlain ATS 2113X.

A complete Chamberlain manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chamberlain ATS 2113X - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chamberlain ATS 2113X, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chamberlain ATS 2113X, that we can find in the current document
3. Tips how to use the basic functions of the device Chamberlain ATS 2113X - which should help us in our first steps of using Chamberlain ATS 2113X
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chamberlain ATS 2113X
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chamberlain ATS 2113X in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chamberlain ATS 2113X?

Use the form below

If you did not solve your problem by using a manual Chamberlain ATS 2113X, ask a question using the form below. If a user had a similar problem with Chamberlain ATS 2113X it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)