English dropdown-ico

Manual Cisco Systems 2975

16 pages 1.92 mb
Download

Go to site of 16

Summary
  • Cisco Systems 2975 - page 1

    G ETTING S TARTED G UIDE Catalyst 2975 Switch Getting Started Guide 1 About this Guide 2 Unpac king the Switc h 3 Running Exp ress Setup 4 Managing the Switc h 5 Planning Switc h Stac ks 6 Rac k-Mounting 7 In Case of Difficulty 8 Obtaining Documentation and Submit ting a Service Req u est ...

  • Cisco Systems 2975 - page 2

    2 1 About this Guide This guide provides instructions on how to use Express Setup to ini tially configure your Cataly st switch. Also covered are swit ch management options, basic rack-mounting, stacking guidelines , port and module connection procedures, and troubleshooting help. For additional installation a nd configuration info rmation for the ...

  • Cisco Systems 2975 - page 3

    3 3 Running Express Setup When you first set up the switch, you should use Express Setup to enter the i nitial IP inform atio n. Doing this enables the swit ch to connect to local ro uters and the Internet. Y ou can then acce ss the switch through the IP a ddress f or furthe r configuration. Y ou need this equipment to set up the switch: • A PC w ...

  • Cisco Systems 2975 - page 4

    4 Step 9 V erify that the LE Ds on bo th Ethernet ports are green. W ait 30 seconds. Step 10 Launch a web browser on y our PC. Enter the IP address 10.0.0.1 in the web browser , and press Enter . Step 11 The Express Setup Basic Se ttings page appears. If i t does not appear , see the “In Case of Difficulty” section on page 14. Step 12 Enter thi ...

  • Cisco Systems 2975 - page 5

    5 Refreshing the PC IP Address After you complete Express Setup, yo u should refresh the PC IP address: • For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect the PC to the network. The network DHCP server assigns a new IP address to the PC. • For a statically assigned IP address, change it to the prev iously ...

  • Cisco Systems 2975 - page 6

    6 4 Managing the Switch After you complete Express Setup and install the switch in your network, use the device manage r or other management options described in this section for further configuration. Using the Device Manager The simplest way to manage the switch is by using the devi ce manager in the switch memory . This web interface offers q ui ...

  • Cisco Systems 2975 - page 7

    7 Other Management Options Y ou can use SNM P management applications such as Cisc oW orks Small Network Management Solution (SNMS) and HP OpenV iew to configure and ma nage the switch. Y ou also can ma na ge it from an SNMP-compatible workstation that is running platforms such as HP OpenV iew or S unNet Manager . The Cisco IE2100 Series Configurat ...

  • Cisco Systems 2975 - page 8

    8 Cabling Guidelines These illustrations show the recommended s witch stack configurations with redundant stack cabling connecti ons for optimized stack bandwidth. For more configuration examples, see the hardware installation guide on Cisco.com. In this example, the stack uses the 0.5-mete r stack cable to make redundant conn ections. In this exam ...

  • Cisco Systems 2975 - page 9

    9 6 Rack-Mounting This section covers basic 19-inch rack-mounting and switch por t conn ections. For alternate mounting procedures, such as installing the switch in a 24-inch rack or on a wall, and for additional cabling information, see the hardware installation gui de on Cisco.com. Equipment That You Supply Y ou need a number -2 Phi llips screwdr ...

  • Cisco Systems 2975 - page 10

    10 Installation Warning Statements This section includes the basic installatio n warning statemen ts. T ranslations of these warning statements appear in the Regulatory Compliance and Safety Inform ation for the Catalyst 2975 Switch document on the documentation CD. War n in g T o prevent bodily injury when mounting or servicing th is unit in a rac ...

  • Cisco Systems 2975 - page 11

    11 Attaching the Brackets Use two number -8 Phillips flat-head screws to atta ch the long side of each bracket to the swit ch in one of three mounting positions. 1 Front-mounting position 3 Mid-mounting position 2 Number -8 Phillips flat-head screws 4 Rear -mounting position Catalyst 2975G S e r ie s PoE-48 Cat alyst 2975G S e r ie s PoE-48 CONSOLE ...

  • Cisco Systems 2975 - page 12

    12 Rack-Mount the Switch Use the four number -12 Phillips machine scre ws to attach the brackets to the rack. Use the b lack Phillips machine screw to atta ch the cable guide to the left or right bracket. 1 Black Phillips machine screw 4 Number -12 Phillips machine screws 2 Cable guide 5 Mid-mounting position 3 Front-mounting position 6 Rear -mount ...

  • Cisco Systems 2975 - page 13

    13 Connect the Stack Cables Use the window in the stack cable to align the connector correctly . Insert the cable into the stack port on the back of the swi tch. Secure the screws tightly . Insert the othe r end of the cable into the connector of th e other switch, and secure the screws tigh tly . Always use a Cisco-approved stack cable to connect ...

  • Cisco Systems 2975 - page 14

    14 Install SFP Modules and Conne ct to the Module Ports The switch Gigabit Ethernet SFP modules are used for c onnections to other devices. These modules are fie ld-replaceable, providing the uplink interfaces when inserted in an SFP module slot. Y ou can use any combination of SF P modules. See the switch release notes for th e list of SF P module ...

  • Cisco Systems 2975 - page 15

    15 Resetting the Switch This section describes how to reset the sw itch by rerunning Express Setup. These ar e reasons why you m ight want to reset th e switch: • Y ou installed the switch in your network a nd cannot connec t to it because yo u assigned an incorrect IP address. • Y ou want to clear all configuration from the switch and assign a ...

  • Cisco Systems 2975 - page 16

    Americas He adquarters Cisco Systems, Inc. San Jose, CA Asia Pacific Headqua rters Cisco Systems (USA) Pte. Ltd. Singapore Europe Head quarters Cisco Systems International BV Amsterdam, The Netherlands Cisco has more than 200 offices wo rldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco W ebsite at www .cisco.com/go/offices ...

Manufacturer Cisco Systems Category Switch

Documents that we receive from a manufacturer of a Cisco Systems 2975 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 2975 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 2975
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 2975.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 2975, service manual, brief instructions and user manuals Cisco Systems 2975. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 2975.

Similar manuals

A complete manual for the device Cisco Systems 2975, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 2975 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 2975.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 2975 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 2975, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 2975, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 2975 - which should help us in our first steps of using Cisco Systems 2975
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 2975
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 2975 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 2975?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 2975, ask a question using the form below. If a user had a similar problem with Cisco Systems 2975 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)