Manual Makita EK6101

28 pages 3.9 mb
Download

Go to site of 28

Summary
  • Makita EK6101 - page 1

    Important: Read this instruction manual carefully before putting the Power Cut into operation and strictly observe the safety regulations! Keep this instruction manual! Instruction Manual Original Instruction Manual EK6100 EK6101 ...

  • Makita EK6101 - page 2

    2 Thank you for purchasing a MAKIT A product! Congratulations on choosing a MAKIT A Power Cut cutof f saw! Like our chain saws, the MAKIT A Power Cuts feature spe- cially designed high-performance engines with outstanding power-to-weight ratios, for heavy-duty yet lightweight tools. Other advantages of the MAKIT A Power Cuts: • Sturdy constructio ...

  • Makita EK6101 - page 3

    3 Delivery inventory 1. Power Cut 2. Cutting disc (not in the general scope of delivery . Country-speci Þ c) 3. Screwdriver (for carburetor adjustment) 4. Offset screwdriver 5. Universal wrench 13/19 6. Instruction manual (not shown) Symbols Y ou will notice the following symbols on the Power Cut and in the Instruction Manual: In case one of the p ...

  • Makita EK6101 - page 4

    4 2 3 1 4 SAFETY PRECAUTIONS Note: The illustrations in the safety precautions are not identical with the product! Intended use Power Cut Use the Power Cut cutoff saw outdoors only , for trimming and cutting suitable materials, using cutting discs rated for this machine. Improper use: Never use the cutoff saw cutting discs for grinding or sanding ( ...

  • Makita EK6101 - page 5

    5 - Always wear safety shoes or boots (G) with steel toes, non-skid soles, and leg protectors when working with the Power Cut. Safety shoes equipped with a protective layer provide protection against cuts and ensure a secure footing. - Always wear a work suit (H) of tough material with suf Þ cient ß ame-retardant qualities whenever working with t ...

  • Makita EK6101 - page 6

    6 Cutoff discs - The protection hood must always be on! Change discs only with the engine off! - There are two basic types of cutoff discs: - For metal (hot cutting) - For masonry (cold cutting) NOTE: When using diamond cutoff discs, always make sure to observe the "direction of rotation" markings. Diamond discs should only be used for cu ...

  • Makita EK6101 - page 7

    7 Kickback and lock-in - When working with the Power Cut there is a danger of kickback and lock-in. - Kickback occurs when the top of the cutting disc is used for cutting (15). - This causes the Power Cut to be thrown back toward the user with great force and out of control. Risk of injury! T o prevent kickback, observe the following: - Never cut w ...

  • Makita EK6101 - page 8

    8 When using synthetic resin cutting discs, always ob- serve the following: CAUTION : - Synthetic resin cutting discs can absorb moisture. This moisture can cause the disc to become unbalanced at high speed. This imbalance can cause the disc to break. - Do not cool resin cutting discs with water or other ß uids. - Do not expose resin cutting discs ...

  • Makita EK6101 - page 9

    9 In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water . MAKITA offers the right accessories for all wet cutting applications (see also "SPECIAL ACCESSORIES"). - Remove foreign objects such as sand, stones and nails found within the working area. Caution: Watch out for electric wires and cables! The rapi ...

  • Makita EK6101 - page 10

    10 Maintenance - Before performing maintenance work switch off the Power Cut (27) and pull out the plug cap. - Always check the Power Cut before using it to make sure that it is in good working order . In particular, make sure that the cutting disc is properly mounted. Make sure that the cutting wheel is undamaged and suitable for the job it will b ...

  • Makita EK6101 - page 11

    11 T echnical data Displacement cm 3 60.7 60.7 Bore mm 47 47 Stroke mm 35 35 Max. power / operating speed kW/1/min 3.2 / 9.500 3.2 / 9.500 Max. torque Nm 3.9 3.9 Idling speed 1/min 2.600 2.600 Clutch engagement speed 1/min 3.900 3.900 Engine speed limitation 1/min 9.850 ± 150 9.850 ± 150 Max. spindle speed 1/min 5.100 4.400 Sound pressure level L ...

  • Makita EK6101 - page 12

    12 Denomination of components Serial number Y ear of manufacture Identi Þ cation plate (9) Indicate when ordering spare parts 1 2 3 4 56 8 9 10 11 12 20 21 23 24 25 7 15 13 14 17 16 22 18 19 EK6101 2013 123456 XXX.XXX.XXX Typ XXX Makita Corporation, Anjo, Aichi, Japan Made in Germany 1 Handle 2 Air Þ lter cover 3 Tubular handle 4 Protection hood ...

  • Makita EK6101 - page 13

    13 PUTTING INTO OPERA TION CAUTION: Always turn off the engine and pull off the spark plug cap before doing any work on the Power Cut! Always wear protective gloves! CAUTION: Start the Power Cut only after complete assembly and inspection. Sequence For the the following work, use the assembly tools included with delivery: 1. 13/19 AF combination wr ...

  • Makita EK6101 - page 14

    14 Fuel CAUTION: This saw is powered by mineral-oil products (gasoline and oil) . Be especially careful when handling gasoline. Avoid all ß ame or Þ re. Do not smoke (explosion hazard). Fuel mixture This tool is powered by a high-performance air-cooled two- stroke engine. It runs on a mixture of gasoline and two-stroke engine oil. The engine is d ...

  • Makita EK6101 - page 15

    15 Refuelling IMPORT ANT : FOLLOW THE SAFETY PRECAUTIONS! Be careful and cautious when handling fuels. The engine must be turned off and cooled down! Carefully clean the area around the fuel-tank Þ ller neck to keep dirt from getting in the tank. Place the Power Cut on an even surface. Unscrew the tank cap and Þ ll tank with fuel mixture. T ake c ...

  • Makita EK6101 - page 16

    16 3 4 5 6 2 1 2a Cold start (Choke) W arm start (ON) Engine off Combination switch in safety position (ignition current cut off, necessary for all maintenance, repair , and installation work) Cold starting: Grasp front handle Þ rmly with one hand and press the Power Cut against the ground. Place left toe in the rear handguard. Prime the fuel pump ...

  • Makita EK6101 - page 17

    17 Adjusting the carburetor NOTE: The grinding parts are equipped with an electronic ignition to limit the speed. At the factory the idling speed has been set to approx. 2600 rpm, but the running-in process of a new engine may require slight readjustment of the idling speed. Adjustments to the adjusting screws (L) and (H) may only be made by an aut ...

  • Makita EK6101 - page 18

    18 IMPORT ANT : Because many of the parts and assemblies not mentioned in this Instruction Manual are vital to the safety of the unit, and because all parts are subject to a certain amount of wear and tear , it is important for your own safety that you have the unit checked and maintained regularly by a MAKIT A service center . IMPORT ANT : If the ...

  • Makita EK6101 - page 19

    19 Cleaning the protection hood Over time, the inside of the protective hood can become caked with material residue (especially from wet cutting), which if allowed to accumulate can hinder the free rotation of the cut- ting disc. For this reason the hood must be cleaned out from time to time. T ake off the cutting wheel with spring washer and remov ...

  • Makita EK6101 - page 20

    20 Checking the ignition spark Insert the combination tool ( 2 ) between the ventilation hood and cylinder only as shown in the illustration. CAUTION! Do not insert the combination tool into the spark plug hole, but make contact only with the cylinder (otherwise you may damage the engine). Using insulated pliers, hold the spark plug ( 3 ) (unscrewe ...

  • Makita EK6101 - page 21

    21 12 11 7 8 5 3 14 12 10 6 9 2 13 4 1 15 16 Replacing the starter cable Unscrew four screws ( 1 ). Remove fan housing ( 2 ). Insert a small screwdriver through the ventilation slit on the back of the fan housing ( 2 ) near the holder ( 15 ). Bend the air guide tab ( 4a ) slightly to the side and carefully remove the air guide ( 3 ) from the fan ho ...

  • Makita EK6101 - page 22

    22 7 8 13 3 4 5 1 6 15 Replacing the return spring pack/Replacing the starter spring Remove the fan housing (see “Replacing the starter cable”). Remove the air guide from the fan housing (see “Replacing the starter cable”). Detension the return spring on the cable drum and remove the cable drum (see “Replacing the starter cable”). Note: ...

  • Makita EK6101 - page 23

    23 Instructions for periodic maintenance T o ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be per- formed regularly . Guarantee claims can be recognized only if this work is performed regularly and properly . Failure to perform the prescribed maintenance work can lead to accid ...

  • Makita EK6101 - page 24

    24 Spare parts Reliable long-term operation, as well as the safety of your Power Cut, depend among other things on the quality of the spare pa rts used. Use only original MAKIT A parts, marked Only original parts are from the same production line as the original unit and therefore ensure the highest possible quality of materi- als, dimensions, func ...

  • Makita EK6101 - page 25

    25 T roubleshooting Malfunction System Observation Cause Cutting disc does not start turning Clutch Engine runs Damage to clutch Cutting disc runs in idle Carburetor , Cutting disc runs Incorrect idle speed, clutch blocked clutch V -belt Belt has insuf Þ cient tension, V -belt is worn Engine does not start or Ignition system Ignition spark Malfunc ...

  • Makita EK6101 - page 26

    26 Extract from the spare parts list Use only original MAKIT A parts. For repairs and replacement of other parts, see your MAKIT A service centre. EK6100 EK6101 22 6 5 14 15 16 9 8 17 18 19 ...

  • Makita EK6101 - page 27

    27 Extract from the spare parts list Use only original MAKIT A parts. For repairs and replacement of other parts, see your MAKIT A service centre. EK6100 EK6101 Pos. MAKIT A-No. Qty . Denomination Synthetic resin cutting disc 1 966 121 150 1 Cutting disc for steel, dia. 300/20 mm 966 141 150 1 Cutting disc for steel, dia. 350/20 mm 966 144 150 1 Cu ...

  • Makita EK6101 - page 28

    Form: 995 704 531 (2013-10 GB) Speci Þ cations subject to change without notice To Þ nd your local distributor , please visit www .makita-outdoor .com MAKIT A Corporation 3-1 1-8 Sumiyoshi-Cho Anjo, Aichi 446-8502 Japan This print product has been awarded the “Blue Angel”. ...

Manufacturer Makita Category Pole Saw

Documents that we receive from a manufacturer of a Makita EK6101 can be divided into several groups. They are, among others:
- Makita technical drawings
- EK6101 manuals
- Makita product data sheets
- information booklets
- or energy labels Makita EK6101
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita EK6101.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita EK6101, service manual, brief instructions and user manuals Makita EK6101. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita EK6101.

Similar manuals

A complete manual for the device Makita EK6101, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita EK6101 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita EK6101.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita EK6101 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita EK6101, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita EK6101, that we can find in the current document
3. Tips how to use the basic functions of the device Makita EK6101 - which should help us in our first steps of using Makita EK6101
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita EK6101
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita EK6101 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita EK6101?

Use the form below

If you did not solve your problem by using a manual Makita EK6101, ask a question using the form below. If a user had a similar problem with Makita EK6101 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)