Manual Hunter Fan 41949-01

40 pages 11.83 mb
Download

Go to site of 40

Summary
  • Hunter Fan 41949-01 - page 1

    41949-01 02/12/2008 1 Installation Guide 83001 Riazzi Bath V entilator with Light READ and SA VE THESE INSTRUCTIONS ENGLISH See page 2 ESP AÑOL V ea la página 21 011_41949_EngS_2-12-08.indd 1 2/12/08 2:43:22 PM ...

  • Hunter Fan 41949-01 - page 2

    41949-01 02/12/2008 2 DISCONNECT ELECTRIC POWER SUPPL Y AND LOCK OUT SER VICE P ANEL BEFORE SER VICING UNIT W ARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y TO PERSONS, OBSERVE THE FOLLOWING: 1. For general ventilating use only . Do not use to exhaust hazard- ous or explosive materials and vapors. 2. T o avoid motor bearing damage an ...

  • Hunter Fan 41949-01 - page 3

    41949-01 02/12/2008 3 E F G H I J M N O x5 * * * NOTE: Strain relief cable connector must be installed. Not Included. A B C 95044-01-000 95022-01-000 75867-01-000 03242-07-133 95492-04-000 74508-03-133 96373-01-214 K 77520-01 L 65219 75184-01-133 96374-01-214 Extra Screws x2 D x2 3/8” Cable Connector 1 T urn off the power source. T ools Needed. ( ...

  • Hunter Fan 41949-01 - page 4

    41949-01 02/12/2008 4 5 4 7 H 8 G Remove the motor/blower from the housing. 3 I F Remove the pre-loaded screw tip covers. Remove the wiring cover screw. 6 Back out the pre-loaded screw tips until flush with the side of the housing. Remove the wiring cover . Remove packing material. 011_41949_EngS_2-12-08.indd 4 2/12/08 2:43:28 PM ...

  • Hunter Fan 41949-01 - page 5

    41949-01 02/12/2008 5 9 F Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not Included) into the housing and secure with washer . Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. New Construction - attaching to joist 1 0 B C Choose Installation Option For ...

  • Hunter Fan 41949-01 - page 6

    41949-01 02/12/2008 6 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground A 1 4 Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option A 1 3 0 A 1 6 Route wires through strain relief. For supply connection, use wires su ...

  • Hunter Fan 41949-01 - page 7

    41949-01 02/12/2008 7 A 1 9 J Secure the motor by tightening the 2 screws. A 2 0 T urn on the power source. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. 0 0 0 0 A 1 7 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. 0 0 0 ...

  • Hunter Fan 41949-01 - page 8

    41949-01 02/12/2008 8 5/8 1/2 5/8 1/2 B 1 2 Slide the mounting rails into brackets. Mark position of screws by using holes as a template. Insert screws, leaving space between the screw head and the joist. Screws are not provided. New Construction – suspended between joists B 1 1 E F 1/8” bit B 1 4 B 1 5 F B 1 3 Position the correct depth mark a ...

  • Hunter Fan 41949-01 - page 9

    41949-01 02/12/2008 9 Tighten screws. Route wires through strain relief. For supply connection, use wires suitable for at least 90º C (194º F). Connect wires as shown. B 1 7 B 1 8 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground B 1 9 Night Light Night Light Switch 1 (AC In) Main Switc ...

  • Hunter Fan 41949-01 - page 10

    41949-01 02/12/2008 10 B 2 7 E1 Go to step on page 17 to attach grille . B 2 2 I Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. I B 2 3 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. B 2 5 T urn on the power source. O N O ...

  • Hunter Fan 41949-01 - page 11

    41949-01 02/12/2008 1 1 C 1 2 E F Existing Construction – accessible from above EXISTING F AN C 1 1 NO EXISTING F AN 9” 9.75” OR Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Cut out an opening for the housing. Use the motor housing as a template to mark positio ...

  • Hunter Fan 41949-01 - page 12

    41949-01 02/12/2008 12 C 1 7 C 1 8 C 1 9 C 2 0 C 1 5 C 1 6 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. Tighten screws. Connect 4” duct and vent to the outside. T ape joints. If ducting does not fit securely , an adapter ma ...

  • Hunter Fan 41949-01 - page 13

    41949-01 02/12/2008 13 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground C 2 2 Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option Tighten the strain relief screws. Connect wires as shown. C 2 4 I H C 2 3 G Install ...

  • Hunter Fan 41949-01 - page 14

    41949-01 02/12/2008 14 C 2 5 I C 2 6 J C 2 7 O N O F F C 2 8 Secure the motor by tightening the 2 screws. T urn on the power source. T est the motor . If the motor does not run, check the plug connection. C 2 9 E1 Go to step on page 17 to attach grille . Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are ...

  • Hunter Fan 41949-01 - page 15

    41949-01 02/12/2008 15 EXISTING F AN D 1 1 F D 1 2 Existing Construction – accessible only from below D 1 3 2 1 D 1 4 Route wires through strain relief. For supply connection, use wires suitable for at least 90º C (194º F). Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75 ...

  • Hunter Fan 41949-01 - page 16

    41949-01 02/12/2008 16 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground D 1 6 Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option I D 1 8 I D 1 9 D 2 0 J Connect wires as shown. Reinstall the motor by inserting th ...

  • Hunter Fan 41949-01 - page 17

    41949-01 02/12/2008 17 O N O F F D 2 2 D 2 3 E1 Go to step on page 17 to attach grille . D 2 1 T est the motor . If the motor does not run, check the plug connection. T urn on the power source. Attaching the Grille Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. N F E 1 M E 2 011_41949_EngS_ ...

  • Hunter Fan 41949-01 - page 18

    41949-01 02/12/2008 18 Position the strain relief bracket between the plugs as shown, and screw into place. K E 3 Align tabs on glass dome assembly with slots on light fixture, and insert tabs into slots. Install 2 Max 60 watt A-15 bulbs (Not Included). E 8 T urn glass dome assembly as shown until it locks into position. E 6 O E 7 Attach thumbscrew ...

  • Hunter Fan 41949-01 - page 19

    41949-01 02/12/2008 19 T rouble Shooting Problem: Fan does not come on. Solution:  • HunterFanBathV entilatorsareextremelyquiet.T oconrmthatthefanisrunning,placeyourhandneartheventstofeel the air movement. • T urn power on, replace fuse, or reset breaker . • Chec ...

  • Hunter Fan 41949-01 - page 20

    41949-01 02/12/2008 20 2500 Frisco A venue, Memphis, T ennessee 381 14 Printed in China W arranty Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: IfanypartofyourHunterbathexhaustfan(exc ...

  • Hunter Fan 41949-01 - page 21

    41949-02 02/12/2008 21 Guía de instalación V entilador para baño Riazzi 83001 con luz LEA y CONSERVE EST AS INSTRUCCIONES ESP AÑOL 011_41949_Sp_2-12-08.indd 21 2/12/08 2:46:25 PM ...

  • Hunter Fan 41949-01 - page 22

    41949-02 02/12/2008 22 DESCONECTE LA ALIMENT ACIÓN ELÉCTRICA Y CIERRE EL P ANEL DE SER VICIO ANTES DE DAR MANTENIMIENT O A LA UNIDAD tc. Retire las cubiertas de las puntas de tornillo pre- cargadas. ADVERTENCIA P ARA REDUCIR EL RIESGO DE INCENDIO, CHOQUE ELÉCTRICO O LESIONES A PERSONAS, OBSERVE LO SIGUIENTE: 1. Sólo para uso de ventilación gen ...

  • Hunter Fan 41949-01 - page 23

    41949-02 02/12/2008 23 E F G H I J M N O x5 * * * NOT A: Debe estar instalado el manguito de alivio de tensión del cable. No incluido. A B C 95044-01-000 95022-01-000 75867-01-000 03242-07-133 95492-04-000 74508-03-133 96373-01-214 K 77520-01 L 65219 75184-01-133 96374-01-214 T ornillos adicionales x2 D x2 Conector de cable de 3/8” 1 Incluido. 2 ...

  • Hunter Fan 41949-01 - page 24

    41949-02 02/12/2008 24 5 4 7 H 8 G 3 I F 6 Retire el motor/soplador del alojamiento. Retire las cubiertas de las puntas de tornillo precargadas. Retire el tornillo de la cubierta del cableado. Retire las puntas de tornillo precargadas hasta que estén a nivel con el lado del alojamiento. Retire la cubierta del cableado. Retire el material de embala ...

  • Hunter Fan 41949-01 - page 25

    41949-02 02/12/2008 25 9 F 1 0 B C A 1 1 F 5/8 1/2 5/8 1/2 A 1 2 Retire el primer tapón metálico de acceso del cableado. Utilice el segundo si es necesario. Inserte el manguito de alivio de tensión (no se incluye) en la caja y sujételo firmemente con una arandela. Ubique la correcta marca de profundidad en el borde inferior de la viga, según e ...

  • Hunter Fan 41949-01 - page 26

    41949-02 02/12/2008 26 A Rojo Interruptor 1 (CA) 3 pasadores 3 clavijas 2 pasadores 2 clavijas Luz Luz V erde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Rojo Luz de noche Blanco Negro Negro Blanco Blanco Cobre desnudo Tierra Luz de noche *Opción V entilador y luz principal juntos *Opción Motor del ventilador A 1 4 A 1 3 0 A 1 6 H ...

  • Hunter Fan 41949-01 - page 27

    41949-02 02/12/2008 27 A 1 9 J A 2 0 0 0 0 0 A 1 7 0 0 0 0 I A 1 8 E NC EN D I DO A P AG AD O A 2 1 A 2 2 E1 Vaya al paso en la página 37 para fijar la rejilla. Asegure el motor apretando los 2 tornillos. Encienda la fuente de alimentación. Conecte el mazo de cables. NO PERMIT A QUE EL MOTOR CUELGUE DEL MAZO DE CABLES. V uelva a instalar el motor ...

  • Hunter Fan 41949-01 - page 28

    41949-02 02/12/2008 28 B 1 1 E F 5/8 1/2 5/8 1/2 B 1 2 broca de 1/8 de pulg. B 1 4 B 1 5 F B 1 3 B 1 6 Deslice los rieles de montaje en los soportes. Marque la posición de los tornillos utilizando los agujeros como una plantilla. Introduzca los tornillos, dejando espacio entre la cabeza del tornillo y la viga. No se proporcionan los tornillos. Con ...

  • Hunter Fan 41949-01 - page 29

    41949-02 02/12/2008 29 B 1 7 B 1 8 A Rojo Interruptor 1 (CA) 3 pasadores 3 clavijas 2 pasadores 2 clavijas Luz Luz V erde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Rojo Luz de noche Blanco Negro Negro Blanco Blanco Cobre desnudo Tierra Luz de noche *Opción V entilador y luz principal juntos *Opción Motor del ventilador B 1 9 B 2 ...

  • Hunter Fan 41949-01 - page 30

    41949-02 02/12/2008 30 B 2 7 E1 Vaya al paso en la página 37 para fijar la rejilla. B 2 2 I I B 2 3 B 2 5 E NC EN D I DO A P AG AD O B 2 6 B 2 4 J Conecte el mazo de cables. NO PERMIT A QUE EL MOTOR CUELGUE DEL MAZO DE CABLES. V uelva a instalar el motor introduciendo las pestañas y levantando a su posición. Asegúrese que los alambres no se pel ...

  • Hunter Fan 41949-01 - page 31

    41949-02 02/12/2008 31 C 1 2 E F VENTILADOR EXISTENTE C 1 1 SIN VENTILADOR EXISTENTE 9” 9.75” O 5/8 1/2 5/8 1/2 C 1 3 C 1 4 Construcción existente – accesible desde arriba Retire el ventilador existente y asegúrese que la abertura sea suficientemente grande para acomodar el alojamiento del motor nuevo (9” x 9.75”). Recorte una abertura ...

  • Hunter Fan 41949-01 - page 32

    41949-02 02/12/2008 32 C 1 7 C 1 8 C 1 9 C 2 0 C 1 5 C 1 6 T aladre un agujero en el centro de cada perfil. Introduzca los tornillos, dejando espacio entre la cabeza del tornillo y la viga. No se proporcionan los tornillos. Fije los rieles con los tornillos. Apriete los tornillos. Conecte un ducto de 4” y ventile hacia el exterior . Aplique cinta ...

  • Hunter Fan 41949-01 - page 33

    41949-02 02/12/2008 33 C 2 1 A Rojo Interruptor 1 (CA) 3 pasadores 3 clavijas 2 pasadores 2 clavijas Luz Luz V erde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Rojo Luz de noche Blanco Negro Negro Blanco Blanco Cobre desnudo Tierra Luz de noche *Opción V entilador y luz principal juntos *Opción Motor del ventilador C 2 2 C 2 4 I H ...

  • Hunter Fan 41949-01 - page 34

    41949-02 02/12/2008 34 C 2 5 I C 2 6 J C 2 7 E NC EN D I DO A P AG AD O C 2 8 C 2 9 E1 Vaya al paso en la página 37 para fijar la rejilla. Asegure el motor apretando los 2 tornillos. Encienda la fuente de alimentación. Pruebe el motor . Si el motor no funciona, verifique la conexión del enchufe. V uelva a instalar el motor introduciendo las pest ...

  • Hunter Fan 41949-01 - page 35

    41949-02 02/12/2008 35 VENTILADOR EXISTENTE D 1 1 F D 1 2 D 1 3 2 1 D 1 4 F D 1 5 Construcción existente – accesible sólo desde abajo Retire el ventilador existente y asegúrese que la abertura sea suficientemente grande para acomodar el alojamiento del motor nuevo (9” x 9.75”). Mueva el alojamiento a su posición encima del techo. Conecte ...

  • Hunter Fan 41949-01 - page 36

    41949-02 02/12/2008 36 A Rojo Interruptor 1 (CA) 3 pasadores 3 clavijas 2 pasadores 2 clavijas Luz Luz V erde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Rojo Luz de noche Blanco Negro Negro Blanco Blanco Cobre desnudo Tierra Luz de noche *Opción V entilador y luz principal juntos *Opción Motor del ventilador D 1 6 I D 1 8 I D 1 9 ...

  • Hunter Fan 41949-01 - page 37

    41949-02 02/12/2008 37 E NC EN D I DO A P AG AD O D 2 2 D 2 3 E1 Vaya al paso en la página 37 para fijar la rejilla. D 2 1 N F E 1 M E 2 Pruebe el motor . Si el motor no funciona, verifique la conexión del enchufe. Encienda la fuente de alimentación. Fijación de la rejilla Retire los tornillos de mano. Conecte el mazo de cables. NO PERMIT A QUE ...

  • Hunter Fan 41949-01 - page 38

    41949-02 02/12/2008 38 Coloque el soporte del aliviador de tensiones entre los enchufes mostrados y enrósquelo en posición. K E 3 Alinee las lengüetas del conjunto de la pantalla con las ranuras del dispositivo de iluminación e inserte las lengüetas en las ranuras. Instale 2 bombillas A-15 de 60 vatios como máximo (No incluidas). E 8 Gire el ...

  • Hunter Fan 41949-01 - page 39

    41949-02 02/12/2008 39 Solución de problemas Problema: El ventilador no está operando. Solución: • Los ventiladores de baño Hunter son muy silenciosos. Para conrma r que el ventilador esté funcionando, coloque su mano cerca de los conductos de ventilación para sentir el movimiento del aire. • Encienda la alimentación eléctrica, reemp ...

  • Hunter Fan 41949-01 - page 40

    41949-02 02/12/2008 40 2500 Frisco A venue, Memphis, T ennessee 381 14 Impreso en China © 2008 Hunter Fan Company Garantía Hunter Fan Company Extractor de aire para baño GARANTÍA LIMIT ADA Hun ter F an C ompan y est able ce la sig uient e gar antí a lim itad a al usua rio o comp rado r ori gina l de este Extr actor de aire para baño Hunt er: ...

Manufacturer Hunter Fan Category Ventilation Hood

Documents that we receive from a manufacturer of a Hunter Fan 41949-01 can be divided into several groups. They are, among others:
- Hunter Fan technical drawings
- 41949-01 manuals
- Hunter Fan product data sheets
- information booklets
- or energy labels Hunter Fan 41949-01
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hunter Fan 41949-01.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hunter Fan 41949-01, service manual, brief instructions and user manuals Hunter Fan 41949-01. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hunter Fan 41949-01.

Similar manuals

A complete manual for the device Hunter Fan 41949-01, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hunter Fan 41949-01 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hunter Fan 41949-01.

A complete Hunter Fan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hunter Fan 41949-01 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hunter Fan 41949-01, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hunter Fan 41949-01, that we can find in the current document
3. Tips how to use the basic functions of the device Hunter Fan 41949-01 - which should help us in our first steps of using Hunter Fan 41949-01
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hunter Fan 41949-01
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hunter Fan 41949-01 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hunter Fan 41949-01?

Use the form below

If you did not solve your problem by using a manual Hunter Fan 41949-01, ask a question using the form below. If a user had a similar problem with Hunter Fan 41949-01 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)