English dropdown-ico

Manual Cisco Systems BC-281

54 pages 0.56 mb
Download

Go to site of 54

Summary
  • Cisco Systems BC-281 - page 1

    BC-281 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Configuring Data-Link Switching Plus This chapter describes ho w to conf igure data-link sw itching plus (D LSw+), Cisco’ s implementation of the DLSw standard for Systems Network Architect ure (SN A) and NetBIOS de vices. Refer to the DLSw+ Design and Implem entation ...

  • Cisco Systems BC-281 - page 2

    Configuring Data-Link Switching Plus Technology Overview BC-282 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 DLSw Standard The DLSw standard, documented in RFC 1795 , defi nes the switch-to-switch protocol between DLSw routers. The standard also def ine s a mechanism to terminate data-l ink control connections locally and ...

  • Cisco Systems BC-281 - page 3

    Configuring Data-L ink Switching Plus Technology Overview BC-283 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 UDP Unicast DLSw V ersion 2 uses UDP unicast in response to an IP multicast. When ad dress resolution packets (CANUREA CH_EX, NETBIOS_NQ _ex, NETBIOS_ANQ, and D A T AFRAME) are sent to mu ltiple destinations (IP ...

  • Cisco Systems BC-281 - page 4

    Configuring Data-Link Switching Plus Technology Overview BC-284 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 • UDP unicast support • Load balancing • Support for LLC1 circuits • Support for multi ple bridge groups • Support for RIF P assthrough • SN A type of service feature support • Local ackno w ledgment ...

  • Cisco Systems BC-281 - page 5

    Configuring Data-L ink Switching Plus Technology Overview BC-285 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Figure 127 LLC2 Session without Local Acknowledgment On backbone networks consisting of slo w serial links, the T1 timer on end hosts could e xpire before the frames reach the remote hosts, causi ng the end ho st ...

  • Cisco Systems BC-281 - page 6

    Configuring Data-Link Switching Plus Technology Overview BC-286 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Enabling local ackn owledgment for LLC2 has t he following adv antages: • Local ackno wledgment for LLC2 solves the T1 ti mer problem without having to change any configuration on the end nodes. The end nodes are ...

  • Cisco Systems BC-281 - page 7

    Configuring Data-L ink Switching Plus Technology Overview BC-287 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 If you are using NetBIOS applications, note that there are two NetBIOS timers—o ne at the link le vel and one at th e next higher le vel. Lo cal acknowledgme nt for LLC2 is designed to solve link timeouts only ...

  • Cisco Systems BC-281 - page 8

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-288 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Figure 129 VDLC Interaction with Higher -La yer Prot oc ol s The higher -layer protocols make no distinction betw een the VDLC and any other data-lin k control, but they do identi fy the VDL C as a desti ...

  • Cisco Systems BC-281 - page 9

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-289 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Defining a DLSw+ Remote Peer Defin ing a remote peer in DLSw+ is optional, ho we ver , usually at least one side of a peer co nnection has a dlsw remote-peer statemen t. If you omit the dlsw remote-peer ...

  • Cisco Systems BC-281 - page 10

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-290 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 TCP/IP with RIF Passthrough Encapsulation T o configure TCP/ IP with RIF Passthrough encap s ulation, use the follo wing command in global confi guration mode: The follo wing command specif ies a remote p ...

  • Cisco Systems BC-281 - page 11

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-291 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Direct Encapsulation T o configure direct encapsulation, use the fo llowing command in g lobal configuration mode: Direct encapsulation is suppor ted over High-Lev el D ata Link Control (H DLC) and Fram ...

  • Cisco Systems BC-281 - page 12

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-292 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Mapping DLSw+ to a Local Data-Link Control In addition to conf iguring local and remote peers, you must map one of the followi ng local data-link controls to DLSw+: • T oken Ring, page 292 • Ethernet, ...

  • Cisco Systems BC-281 - page 13

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-293 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Ethernet T raff ic that origina tes from Ethe rnet is picked up from the local Ethernet interface bridge group and transported across th e DLSw+ network. Therefore, you must map a specif ic Ethernet bri ...

  • Cisco Systems BC-281 - page 14

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-294 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Use the default option if you ha ve more than 10 SDLC d evices to attach to the DLSw+ n etwork. T o confi gure an SDLC multidrop line do wnstream, you conf igure the SDLC role as either primary or prim-xi ...

  • Cisco Systems BC-281 - page 15

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-295 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 • Remote X.25-attached SNA de vices can acce ss an FEP or an AS/400 over a T oken Ring or o ver SDLC. For en vironments ju st beginning to migrate to LANs, our QLLC support allows deployment of LANs i ...

  • Cisco Systems BC-281 - page 16

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-296 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 • Modes of Operation, page 306 ⎯ Dynamically detects the capabilities of the peer rout er and operates according to those capabili ties. • Network Management , page 307 —W orks with enhanced netw ...

  • Cisco Systems BC-281 - page 17

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-297 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 The DLSw+ Peer Clusters fe ature is configured l ocally on the member peer or on a border peer . Altho ugh both options can be con figured , we recommend that the cluster -id of a particular peer is def ...

  • Cisco Systems BC-281 - page 18

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-298 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 T o define peer groups, conf igure border peers and a ssign the local peer to a peer cluster , use the follo wing command in global configuration mode: Use the group k eyword to def ine a peer group, the ...

  • Cisco Systems BC-281 - page 19

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-299 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 T o configure peer -on-demand defaults, use the fo llowing command in global configuration mode: T o define the maximum entries maint ained in a border peer’ s group cache, use the fol lowing command ...

  • Cisco Systems BC-281 - page 20

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-300 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 T o display the contents of the reachabili ty caches, use the followi ng command in privile ged EXEC command mode: Use the group k eyword to display th e reachability information for the bord er peer . Ex ...

  • Cisco Systems BC-281 - page 21

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-301 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 SNA Dial-on-Demand Routing This feature allo w s you to run DLSw+ over a switch ed line and ha ve the Cisco IOS software tak e the switched line do wn dynamically when it is not in use. Uti lizing this ...

  • Cisco Systems BC-281 - page 22

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-302 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 LLC1 Circuits Support for LLC1 circuits more ef ficiently transp orts LLC1 UI traff ic across a DLSw+ cloud. With LLC1 circuit support, th e LLC1 unnumbered information frames (UI) are n o longer subject ...

  • Cisco Systems BC-281 - page 23

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-303 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 T o c onfigure promiscuous p eer defaults, use the following command in global configuration mode : Availability DLSw+ suppo rts th e following featur es that allow it to dynamically finds al ternate pa ...

  • Cisco Systems BC-281 - page 24

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-304 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 For multiple peer connections, peer costs must be applied. The DLSw+ Enhanced Load Balancing feature works only with the lo west (or equal) cost peers. For e xample, if the user specif ies dlswrtr1, dlswr ...

  • Cisco Systems BC-281 - page 25

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-305 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Ethernet Redundancy The DLSw+ Ethernet Redundanc y feature, introdu ced in Cisco IOS Release 12.0(5)T , provides redundanc y and load balancing betw een multiple DLSw+ peers in an Ethernet en vironment. ...

  • Cisco Systems BC-281 - page 26

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-306 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Note If the linger ke yword is set to 0, all e xisting sessions on the backup router immediately drop when the primary recove rs. If the linger keyword i s omitted, all existing sessi ons on the backup ro ...

  • Cisco Systems BC-281 - page 27

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-307 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Network Management There are se v eral network management tools a vailable t o the user to help them more easily manage and troubleshoot their DLSw+ netw ork. CiscoW orks Bl ue Maps provides a logical v ...

  • Cisco Systems BC-281 - page 28

    Configuring Data-Link Switching Plus DLSw+ Configuration Task List BC-308 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Figure 130 Mapping T raf fic Using Por t Lists The defi nition of a port list is optio nal. If you want all peers and all interf aces to receiv e all traff ic, you do not ha ve to defi ne a port list. Sim ...

  • Cisco Systems BC-281 - page 29

    Configuring Data-L ink Switching Plus DLSw+ Configuration Task List BC-309 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Static Paths Static path def initions allo w a router to setup circui ts without send ing explorers. The path specif ies the peer to use to access a MAC address or NetBIOS name. T o configure static pat ...

  • Cisco Systems BC-281 - page 30

    Configuring Data-Link Switching Plus Verifying DLSw+ BC-310 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Configuring DLSw+ Timers T o configure DLSw+ timers, use th e follow ing command in global conf iguration mode: See the DLSw+ Design and Implement ation Guide “Customization” chapter and the Cisco IOS Bridging and ...

  • Cisco Systems BC-281 - page 31

    Configuring Data-L ink Switching Plus Monitoring and Maintaining th e DLSw+ Network BC-311 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Alternately , to verify that DLSw+ is conf igured, issue the follo wing command in pri vileged EXEC mode: The global DLSw+ configuratio n statements, including the dlsw local-peer s tate ...

  • Cisco Systems BC-281 - page 32

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-312 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 See the DLSw+ Design and Im plementation Guide “Using Sho w and Debug Commands” chapter and the Cisco IOS Bridging and IBM Networ king Command Refer ence (V olume 1 of 2) for details of the commands. ...

  • Cisco Systems BC-281 - page 33

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-313 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Figure 131 illu strates a DLSw+ configuration with local ackn owledgment. Because the RIF is terminated, the ring group numbers do not have to be the same. Figure 131 DLSw+ with Local Ac know ledgment— ...

  • Cisco Systems BC-281 - page 34

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-314 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 DLSw+ Using TCP Encapsulation with Local Acknowledgment—Peer Group Configuration Example 1 Figure 132 illustrates border peers with TCP encapsula tion. Router A is conf ig ured to operate in promiscuous ...

  • Cisco Systems BC-281 - page 35

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-315 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 ! interface serial 0 ip unnumbered tokenring 0 bandwidth 56 ! interface tokenring 0 ip address 128.207.150.8 255.255.255.0 ring-speed 16 source-bridge 3 14 31 source-bridge spanning ! router igrp 777 net ...

  • Cisco Systems BC-281 - page 36

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-316 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 DLSw+ Using TCP Encapsulation with Local Acknowledgment—Peer Group Configuration Example 2 Figure 133 illust rates a peer group confi guration that allo ws an y-to-any connection e xcept for Router B. R ...

  • Cisco Systems BC-281 - page 37

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-317 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 dlsw local-peer peer-id 150.150.98.1 group 2 dlsw remote-peer 0 tcp 150.150.100.1 ! interface loopback 0 ip address 150.150.98.1 255.255.255.192 ! interface serial 1 no ip address encapsulation sdlc no k ...

  • Cisco Systems BC-281 - page 38

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-318 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 no ip address ring-speed 16 source-bridge 92 1 2000 source-bridge spanning ! .interface tokenring 0/2 no ip address ring-speed 16 source-bridge 93 1 2000 source-bridge spanning ! router eigrp 202 network ...

  • Cisco Systems BC-281 - page 39

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-319 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 clockrate 19200 sdlc role primary sdlc vmac 4000.1234.5600 sdlc address C1 sdlc xid C1 05DCCCC1 sdlc partner 4001.3745.1088 C1 sdlc address C2 xid-poll sdlc partner 4001.3745.1088 C2 sdlc dlsw C1 C2 In t ...

  • Cisco Systems BC-281 - page 40

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-320 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Router A source-bridge ring-group 1111 dlsw local-peer peer-id 10.2.2.2 dlsw remote-peer 0 tcp 10.1.1.1 interface loopback 0 ip address 10.2.2.2 255.255.255.0 interface TokenRing 0 no ip address ring-spee ...

  • Cisco Systems BC-281 - page 41

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-321 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 dlsw bridge-group 5 ! interface loopback 0 ip address 128.207.111.1 255.255.255.0 interface Ethernet 0 no ip address bridge-group 5 ! bridge 5 protocol ieee Router B hostname Router B ! source-bridge tra ...

  • Cisco Systems BC-281 - page 42

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-322 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 interface fddi 0 no ip address source-bridge 26 1 10 source-bridge spanning Router B source-bridge ring-group 10 dlsw local peer peer-id 132.11.11.3 dlsw remote-peer 0 tcp 132.11.11.2 interface loopback 0 ...

  • Cisco Systems BC-281 - page 43

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-323 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 ! interface loopback 0 ip address 150.150.10.2 255.255.255.0 interface serial 8 ip address 150.150.11.2 255.255.255.192 clockrate 56000 ! interface tokenring 0 no ip address ring-speed 16 source-bridge 5 ...

  • Cisco Systems BC-281 - page 44

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-324 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 source-bridge spanning ! router eigrp 202 network 150.150.0.0 DLSw+ over Frame Relay Configuration Example Frame Relay support e xtends the DLSw+ capabilities to include Frame Relay in direct mode. Frame ...

  • Cisco Systems BC-281 - page 45

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-325 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 interface serial 0 mtu 3000 no ip address encapsulation frame-relay frame-relay lmi-type ansi frame-relay map dlsw 30 DLSw+ over QLLC Configuration Examples The follo wing three examples describe QLLC su ...

  • Cisco Systems BC-281 - page 46

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-326 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 Example 3 In this e xample, two dif ferent X.25 resources want to communicate ove r X.25 to the same FEP . In the router attached to the X.25 network, e very X.25 connection request for X. 121 address 311 ...

  • Cisco Systems BC-281 - page 47

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-327 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 DLSw+ with Enhanced Load Balanc ing Configuration Example Figure 140 sho ws DLSw+ w ith the Enha nced Load B alancing feature. Figur e 140 DLSw+ with En hanced Load Balancing Router A is configured for t ...

  • Cisco Systems BC-281 - page 48

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-328 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 DLSw+ Peer Cluster Feature Configuration Example Figure 141 sho ws a DLSw+ network configured with the DLSw+ Peer Clusters feature. Figure 141 DLSw+ P eer Cluster F eature Because BP2 is configured as the ...

  • Cisco Systems BC-281 - page 49

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-329 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 DLSW+ RSVP Bandwidth Reservation Feature Configuration Example Figure 142 sho ws a DLSw+ netw ork with the DLSw+ RSVP Bandwidth Reservatio n feature conf igured. Figur e 142 DLSw+ RS VP Bandwidth Reserv ...

  • Cisco Systems BC-281 - page 50

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-330 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 DLSw+ RSVP Bandwidth Reservation Feat ure with Border Peers Configuration Example Figure 143 sho ws a DLSw+ border peer network co nfigured with DLSw+ RSVP . Figur e 143 DLSw+ RS VP Bandwidth Reservation ...

  • Cisco Systems BC-281 - page 51

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-331 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 The follo wing output of the show ip rsvp r es command on the DLSWR TR1 verifies that the RSVP reservation w a s successful: DLSWRTR1# show ip rsvp rese To From Pro DPort Sport Next Hop I/F Fi Serv BPS B ...

  • Cisco Systems BC-281 - page 52

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-332 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 dlsw remote-peer 0 tcp 10.1.17.1 interface loopback 0 ip address 10.2.24.3 255.255.255.0 int e1 ip address 150.150.2.2 255.255.255.0 dlsw transparent redundancy-enable 9999.9999.9999 master priority 1 dls ...

  • Cisco Systems BC-281 - page 53

    Configuring Data-L ink Switching Plus DLSw+ Configuration Examples BC-333 Cisco IOS Bridging and IBM Networking Con figu ratio n Guide 78-11737-02 Router A dlsw local peer peer-id 10.2.17.1 dlsw remote-peer 0 tcp 10.3.2.1 dlsw transparent switch-support interface loopback 0 ip address 10.2.17.1 255.255.255.0 int e 0 mac-address 4000.0000.0001 ip ad ...

  • Cisco Systems BC-281 - page 54

    Configuring Data-Link Switching Plus DLSw+ Configuration Examp les BC-334 Cisco IOS Bridging and IBM Ne tw orking Configuration Guide 78-11737-02 ...

Manufacturer Cisco Systems Category Network Hardware

Documents that we receive from a manufacturer of a Cisco Systems BC-281 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- BC-281 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems BC-281
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems BC-281.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems BC-281, service manual, brief instructions and user manuals Cisco Systems BC-281. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems BC-281.

Similar manuals

A complete manual for the device Cisco Systems BC-281, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems BC-281 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems BC-281.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems BC-281 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems BC-281, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems BC-281, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems BC-281 - which should help us in our first steps of using Cisco Systems BC-281
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems BC-281
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems BC-281 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems BC-281?

Use the form below

If you did not solve your problem by using a manual Cisco Systems BC-281, ask a question using the form below. If a user had a similar problem with Cisco Systems BC-281 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)