-
Hearth and Home Technologies 8300 - page 1
Owner’s Manual & Installation Guide for the Champlain (8300) GAS - FIRED DIRECT VENT HEATER READ THIS OWNER’S MANUAL Ope rate and maintain this gas heater according to this instruction manual. Read This Manual In Its Entirety. WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing p ...
-
Hearth and Home Technologies 8300 - page 2
HearthStone Quality Home Heating Products Inc Champlain Model #8300 2 INFORMATION SHEET Record, on this page, all relevant information concerning the purchase, installation, and maintenance of your CHAMPLAIN Gas - Fired Direct Vent heater. This information will facilitate servicing, purchase of replacement parts, and warr anty claims (if necessary) ...
-
Hearth and Home Technologies 8300 - page 3
HearthStone Quality Home Heating Products Inc Champlain Model #8300 3 I NTRODUCTION Congratulations on your purchase of a Champlain Gas - Fired Direct Vent he ater. The Champlain, by HearthStone Cast Iron Stoves, incorporates the latest in balanced vent gas technology, which will provide you with clean, efficient heat for years to come. The Champla ...
-
Hearth and Home Technologies 8300 - page 4
HearthStone Quality Home Heating Products Inc Champlain Model #8300 4 I NTRODUCTION ........................................... 3 S AFETY I NFORMATION ............................... 4 F IRE H AZARD ........................................... 5 S HOCK H AZARD ...................................... 5 M UST BE V ENTED TO THE O UTSIDE ......... 5 S ER ...
-
Hearth and Home Technologies 8300 - page 5
HearthStone Quality Home Heating Products Inc Champlain Model #8300 5 tha t system at test pressures in excess of ½ psig. (3.5k Pa). The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal t o or less than ½ ...
-
Hearth and Home Technologies 8300 - page 6
HearthStone Quality Home Heating Products Inc Champlain Model #8300 6 › WARNING : DO NOT OPERATE THE APPLIANCE WITH THE FRONT GLASS AND CAST FAÇADE REMOVED, CRACKED OR BROKEN. REPLACEMENT OF GLASS SHOULD BE DONE BY A LICENSED OR QUALIFIED SERVICE PERSON . ONLY OPEN FRONT FOR ROUTINE SERVICE. DO NOT SLAM OR STRIKE GLASS. C ERAMIC F IBER L OG S AF ...
-
Hearth and Home Technologies 8300 - page 7
HearthStone Quality Home Heating Products Inc Champlain Model #8300 7 SPECIFICATIONS: L ISTED : D IRECT V ENT G AS H EATER Listed: DV Gas Heater Model: Champlain DV Room Heater Testing Agency: Intertek Testing Services NA Inc. (ITS) Tested to: ANSI Z21.88 - 1998, CSA 2.33 - M98, CAN/CGA2.17 Figure 1: Champlain Dimensions NG LP Input rating (Btu/hr) ...
-
Hearth and Home Technologies 8300 - page 8
HearthStone Quality Home Heating Products Inc Champlain Model #8300 8 O WNER ’ S I NFORMATION The installation must conform with local codes or, in the absences of local codes, the current National Fuel Gas Code, ANSI Z223.1 (NFPA 54) or CAN/CGA B149 Installation Code. (Installer l’appareil selon les codes ou règlements locaux, ou, en l’abse ...
-
Hearth and Home Technologies 8300 - page 9
HearthStone Quality Home Heating Products Inc Champlain Model #8300 9 the “ON” position. If the pilot fails to light, or if it went out due to a premature release of the gas control knob while pressed in the “PILOT” position, wait 60 seconds for the Interlock t o release. Then repeat the lighting process as described in this section of the ...
-
Hearth and Home Technologies 8300 - page 10
HearthStone Quality Home Heating Products Inc Champlain Model #8300 10 will stay on constantly, and the thermostat will not operate. When the switch is in the “T - STAT” position, it will op erate via the thermostat, running only when the thermostat “calls” for heat. When the switch is in the “OFF” position, the pilot remains lit but th ...
-
Hearth and Home Technologies 8300 - page 11
HearthStone Quality Home Heating Products Inc Champlain Model #8300 11 and lint. The exterior surfaces of the unit can be cleaned us ing soap, water, and a soft cloth. Do not use abrasive or chemical cleaners and take care not to scratch the glass or enamel finish (if so equipped) when cleaning the unit. The use of chemical wax based cleaners or po ...
-
Hearth and Home Technologies 8300 - page 12
HearthStone Quality Home Heating Products Inc Champlain Model #8300 12 I TEMS R EQUIRED FOR I NSTALLATION * External regulator (for propane/L.P.G. only) * Piping which complies with local codes * Pipe sealant approved for use with propane/L.P.G. (resistant to sulfur compounds) * Manual shutoff valve * Sediment trap * Tee joint * Pipe wrench * Phill ...
-
Hearth and Home Technologies 8300 - page 13
HearthStone Quality Home Heating Products Inc Champlain Model #8300 13 C HAMPLAIN D IMENSIONS C LEARANCE TO C OMBUSTIBLES Due to high surface temperatures, the unit should be located out of traffic and away from furniture and draperies. Clothing and other flammable material should not be placed on or near the heater. When positioning the unit alway ...
-
Hearth and Home Technologies 8300 - page 14
HearthStone Quality Home Heating Products Inc Champlain Model #8300 14 Figure 4 Figur e 5 ...
-
Hearth and Home Technologies 8300 - page 15
HearthStone Quality Home Heating Products Inc Champlain Model #8300 15 Acceptable Direct Vent TERMINATION Cap locations. Figure 6 ...
-
Hearth and Home Technologies 8300 - page 16
HearthStone Quality Home Heating Products Inc Champlain Model #8300 16 V ENTING I NFORMATION V ENTING C ONNECTION 1. The Champlain Direct Vent is approved for installation only with the vent connecting components listed on this page. Use the following instructions along with the pipe manufacturer’s instructions to complete the installation. 2. At ...
-
Hearth and Home Technologies 8300 - page 17
HearthStone Quality Home Heating Products Inc Champlain Model #8300 17 V ENTING C OMPONENTS & C ONFIGURATION The Champlain cannot be vented jointly with any other solid fuel or gas appli ance. It must be vented directly to the outside of the building using a proper termination as listed in the manual. Your Champlain Direct Vent stove is approve ...
-
Hearth and Home Technologies 8300 - page 18
HearthStone Quality Home Heating Products Inc Champlain Model #8300 18 Figure 8: Acceptable Venting Lengths Figure 9: Allowable Venting Lengths There are several ventin g configurations to choose from. You must choose which configuration will work best for your situation. Following the venting configurations are the venting connection instructions. ...
-
Hearth and Home Technologies 8300 - page 19
HearthStone Quality Home Heating Products Inc Champlain Model #8300 19 F IREPLACE V ENTING C ONFIGURATIONS • 30’ maximum system height (with or without offsets - note shutter setting) • 10’ maximum offset (refer to Figures 8 – 10 shutter setting) • maximum rise to run = 1 to 5 (refer to Figures 8 – 10 note shutter setting) • termina ...
-
Hearth and Home Technologies 8300 - page 20
HearthStone Quality Home Heating Products Inc Champlain Model #8300 20 Figure 10: Fireplace Installation ...
-
Hearth and Home Technologies 8300 - page 21
HearthStone Quality Home Heating Products Inc Champlain Model #8300 21 V ENTING C ONFIGURATIONS - 2’ minimum system height (with or without offsets) - 30’ maximum system height (with or without offsets – note shutter setting) - 10’ maximum offset (refer to Figures 8, 9, & 11 – note shutter setting) - maximum rise to run = 1 to 5 (refe ...
-
Hearth and Home Technologies 8300 - page 22
HearthStone Quality Home Heating Products Inc Champlain Model #8300 22 H ORIZONTAL T ERMINATION V ENTING C ONFIGURATIONS - A minimum of 2’ rise is required (with or without offsets) - 30’ maximum system height (with or without offsets – note shutter setting) - 10’ maximum offset (ref er to Figures 8, 9, & 12 – note shutter setting) - ...
-
Hearth and Home Technologies 8300 - page 23
HearthStone Quality Home Heating Products Inc Champlain Model #8300 23 I NSTALLATION I NSTRUCTIONS FOR THE S TANDARD H ORIZONTAL T ERMINATION M INIMUM V ENTING K IT (K IT #93 - 65000) 1. Install the 4” inner collar by first placing the 4” x 6” gasket ring onto the base of the collar. Install the collar and gasket to the stove using 8 of the s ...
-
Hearth and Home Technologies 8300 - page 24
HearthStone Quality Home Heating Products Inc Champlain Model #8300 24 Cet appareil peut être installé dans un maison préfabriquée (mobile) déjà installée à demeure si les règlements locaux le permettent. Cet appareil doit être utilisé uni quement avec les types de gas indiqués sur la plaque signalétique. Ne pas l’utiliser avec d’a ...
-
Hearth and Home Technologies 8300 - page 25
HearthStone Quality Home Heating Products Inc Champlain Model #8300 25 thermostat wire so it is directed towards the thermostat, being sire to leave a small coil of wire behind the unit so that it can be moved out of position for servicing and cleaning. (At the thermostat, the wires should be connected to the two connection screws on the back of th ...
-
Hearth and Home Technologies 8300 - page 26
HearthStone Quality Home Heating Products Inc Champlain Model #8300 26 Bk Bk W Bk Wiring Color KEY: Br B G YG R Hearthstone Bk Y V c 50 70 90 10 20 30 O OFF 50 60 70 80 90 c 10 20 30 O Wiring Diagram Bk V Y YG Bk W Bk B W G G W Bk Figure 13: Wiring Diagram ...
-
Hearth and Home Technologies 8300 - page 27
HearthStone Quality Home Heating Products Inc Champlain Model #8300 27 Figure 14 G AS S UPPLY & C ONNECTIONS › NOTICE: A qualified technician must connect the heater to the gas supply and leak test the unit before it is approved for use. Consult all cod es. › WARNING: The unit must be installed and connected in accordance with local codes, ...
-
Hearth and Home Technologies 8300 - page 28
HearthStone Quality Home Heating Products Inc Champlain Model #8300 28 NOT INSTALL the heater. Contact your dealer for the correct model or conversion kit. G AS P RESSURE A DJUSTMENT NOTE: A QUALIFIED TECHNICIAN MUST PERFORM THIS PROCEDURE! The supply l ine pressure is tested to ensure is meets minimum pressure requirements, as listed in the Specif ...
-
Hearth and Home Technologies 8300 - page 29
HearthStone Quality Home Heating Products Inc Champlain Model #8300 29 4. Gently place the Middle Log (2) in the firebox against the front of the Rear Log. T here are slots on the underside that fit in between the burner tube and into the burner tube holder. The rear tabs on the Middle Log should touch the front of the Rear Log, and the log should ...
-
Hearth and Home Technologies 8300 - page 30
HearthStone Quality Home Heating Products Inc Champlain Model #8300 30 Figure 15: Log Set Assembly. ...
-
Hearth and Home Technologies 8300 - page 31
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 31 Figure 16: Log Set Assembly. R EMOVAL OF THE L OG S ET To remove the log set, follow the Installation of Log Set instructions in the reverse order. L IGHTING THE U NIT FOR THE F IRST T IME DO NOT LIGHT THE UNIT WITHOUT THE GLASS AND CAST FAÇADE IN PLACE ! › WARNIN ...
-
Hearth and Home Technologies 8300 - page 32
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 32 I NITIAL A D JUSTMENTS Once the Champlain has been set in place, connected and assembled as described in the Clearances To Combustibles, Venting Components & Configurations, Electrical Connections, And Gas Supply and Connections sections of this manual, the unit ...
-
Hearth and Home Technologies 8300 - page 33
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 33 touched. Use only metal tools for this adjustment. Moving the nut toward the fron t of the stove increases the air and moving the nut toward the back of the stove decreases the air. Tighten the nut after making adjustment. The air shutter is factory set and only a qu ...
-
Hearth and Home Technologies 8300 - page 34
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 34 2. The flame should not rise off of the burner tube, called “li fting”. 3. Flames should not impinge heavily on the log set. They should “fit” through the pre - formed spaces designed in the log set. Figure 19: Burner Flame Appearance M AINTENANCE AND C ARE T ...
-
Hearth and Home Technologies 8300 - page 35
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 35 Complete the cleaning procedure by carefully placing the log set within the firebox as described in the Log Set Information section of this manual. Fasten the front façade on. Turn on the gas, light the unit and check for prope r operation. Flame patterns should loo ...
-
Hearth and Home Technologies 8300 - page 36
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 36 P ARTS L ISTS › W ARNING : Do not substitute Materials . For replacement parts, or for information about parts or service, contact your authorized HearthStone retailer. For the name of the authorized retailer nearest to you, call (802) 888 - 5235 or write: HearthSt ...
-
Hearth and Home Technologies 8300 - page 37
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 37 TROUBLESHOOTING Symptom Possible Cause Corrective Action 1. Pilot will not light. A. Insufficient gas pressure, air in the pilot line, or dirty or kinked gas line. A. Using the piezo s parker, try to light the pilot. If it will not light, check the inlet gas pressure ...
-
Hearth and Home Technologies 8300 - page 38
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 38 TROUBLESHOOTING Symptom Possible Cause Corrective Action 3. Pilot burning, no gas to main bu rner, valve knob in the "ON" position, thermostat and/or on/off/t'stat switch in the "ON" position. A. Thermostat switch or wires defective. A. Check ...
-
Hearth and Home Technologies 8300 - page 39
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 39 TROUBLESHOOTING Symptom Possible Cause Corrective Action 8. Floating flames, lazy ill - defined, quiet flames, which roll around, sometimes completely off of the port, sometimes with overly, yellow tips. Possible sooting. Usually accompanied by the odor of aldehydes. ...
-
Hearth and Home Technologies 8300 - page 40
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 40 R ATING L ABEL SERIAL # MODEL # 8300- MODEL NAME: CHAMPLAIN DIRECT VENT GAS FIREPLACE HEATER LISTED: VENTED GAS FIREPLACE HEATER TESTED TO: ANSI Z21.88-1998 CSA 2.33-M98, CAN/CGA-2.17-M91 CERTIFIED FOR CANADA/HOMOLOGUE POUR LE CANADA ALSO FOR MOBILE HOME INSTALLATION ...
-
Hearth and Home Technologies 8300 - page 41
HearthStone Quality Home Heating Products Inc CHAMPLAIN Gas - Fired Direct Vent 41 HEARTHSTONE GAS - FIRED STOVE AND INSERT LIMITED WARRANTIES These warranties give you specific legal rights. You may also have other rights which vary from State to State. HearthStone Quality Home Heating Products, In c. (HearthStone) warrants to the original purchas ...
-
Hearth and Home Technologies 8300 - page 42
CHAMPLAIN DV CE 42 EXCLUSIONS The warranties contained in this document do not cover, nor is HearthStone responsible for: 1. Damage resulting from installation or operation of the Stove in a manner contrary to the owner’s manual. 2. Damage or non - performance resulting from faulty or incomplete setup, installation and start - up or mishandling, ...
-
Hearth and Home Technologies 8300 - page 43
CHAMPLAIN DV CE 43 engine contained on HearthStone’s Web site ( www.hearthstonestoves.com ), or call H earthStone at (802) 888 - 5235, to find a Dealer nearest the Original Purchaser’s location. REMEDY The remedy for any breach of the foregoing warranties will consist of repair or replacement, at HearthStone’s option, of any covered defect in ...
Do you have a question concerning Hearth and Home Technologies 8300?
Use the form below
If you did not solve your problem by using a manual Hearth and Home Technologies 8300, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies 8300 it is likely that he will want to share the way to solve it.