Manual Cub Cadet CC2000

60 pages 2.58 mb
Download

Go to site of 60

Summary
  • Cub Cadet CC2000 - page 1

    FORM 769-00022 (11/01) (10694 rev . P01) Printed in U.S.A. Oper ator’ s Man ual 2-Cycle T r immer Model CC 2000 Warning: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U .S. Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and W ashington require , by law that ...

  • Cub Cadet CC2000 - page 2

    2 T ABLE OF CONTENTS Content Page Section 1: Saf ety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Section 2: Know Y our Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Section 3: Assembly. . . . . . . . . . . ...

  • Cub Cadet CC2000 - page 3

    3 Section 1 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger . The instructions or warnings they give are not substitutes for proper accident prevention measur es. ...

  • Cub Cadet CC2000 - page 4

    4 Safety (continued) • Store fuel only in containers specifically designed and approved for the storage of such materials. • Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen t ...

  • Cub Cadet CC2000 - page 5

    5 Safety (continued) SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety , assembly , operating and maintenance and repair information. SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger , wa ...

  • Cub Cadet CC2000 - page 6

    6 SYMBOL MEANING • SHARP BLADE W ARNING: Sharp blade on cutting attachment shield. T o prevent serious injury , do not touch line cutting blade. • CHOKE CONTROL A • ST ART position. B • RUN position. • DO NOT USE BLADES W ARNING: To prevent serious personal injury , do not attach or operate the unit with any type of blade. W ARNING: The o ...

  • Cub Cadet CC2000 - page 7

    7 Know Y our Unit APPLICA TIONS As a trimmer; • Cutting grass and light weeds. • Edging • Decorative trimming around tr ees, fences, etc. Shaft Grip Cutting Attachment Shield Fuel Cap Throttle Contr ol D-Handle Line Cutting Blade Cutting Attachment Primer Bulb Choke Lever Air Filter Cover Spark Plug On/Off Stop Contr ol Shaft Housing Starter ...

  • Cub Cadet CC2000 - page 8

    8 Assembly Section 3 On some units, the D-handle may be preinstalled and only requir e loosening the screws and adjusting the D-handle to the operator . Go to step 4 for adjusting the D-handle if preinstalled. INST ALLING AND ADJUSTING THE D-HANDLE 1. Remove the screws, nuts and bottom clamp piece that were installed on the D-handle for shipping. 2 ...

  • Cub Cadet CC2000 - page 9

    9 Oil and Fuel Section 4 Oil and Gas Mixing Instructions Old and/or improperly mixed fuel ar e the main r easons for the unit not running pr operly . Be sure to use fresh, clean unleaded fuel. Follow the instructions carefully for the pr oper fuel/oil mixture. Definition of Blended Fuels T oday's fuels are often a blend of gasoline and oxygena ...

  • Cub Cadet CC2000 - page 10

    Operation Section 5 ST ARTING INSTRUCTIONS Operate this unit only in a well ventilated area outdoors. Carbon monoxide exhaust fumes can be lethal in a confined area. A void accidental starting. Be in the starting position whenever pulling the starting rope. T o avoid serious personal injury , the operator and unit must be in a stable position while ...

  • Cub Cadet CC2000 - page 11

    11 Operation (continued) HOLDING THE TRIMMER Always wear eye, hearing, foot and body protection to r educe the risk of injury when operating this unit. Before operating the unit, stand in the operating position (Fig. 5-4). Check for the following: • The operator is wearing eye protection and pr oper clothing. • The right arm is slightly bent, a ...

  • Cub Cadet CC2000 - page 12

    12 Operation (continued) Fig. 5-6 DECORA TIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around tr ees, posts, fences, etc. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground (Fig. 5-6). Section 6 Maintenance NOTE: Some maintenance procedures may require special tools or skills. If you ...

  • Cub Cadet CC2000 - page 13

    13 Maintenance (continued) Fig. 6-4 Inner Reel Outer Spool Spring Shaft Indexing T eeth Fig. 6-3 Slotted Holes For Use with Membrane or Single Line For Use with Single Line ONL Y Fig. 6-2 Fig. 6-5 Loop There ar e two methods to replace the trimming line. • Wind the inner reel with new line • Install a prewound inner r eel Winding the Existing I ...

  • Cub Cadet CC2000 - page 14

    14 Maintenance (continued) Fig. 6-6 Fig. 6-7 Loop Holding Slots Fig. 6-8 Fig. 6-9 7. Wind the lines in tight even layers, onto the reel (Fig. 6-6). Wind the line in the direction indicated on the inner reel. Place your index finger between the two lines to stop the lines from overlapping. Do not overlap the ends of the line. Proceed to step 11. Mem ...

  • Cub Cadet CC2000 - page 15

    15 Fig. 6-10 Fig. 6-12 Fig. 6-11 Maintenance (continued) AIR FIL TER MAINTENANCE Cleaning the Air Filter To avoid serious personal injury , always tur n your trimmer off and allow it to cool befor e you clean or do any maintenance on it. Clean and re-oil the air filter every 10 hours of operation. It is an important item to maintain. Not maintainin ...

  • Cub Cadet CC2000 - page 16

    16 Maintenance (continued) 2. Use a needlenose pliers to grasp the collar of the spark arrestor and pull it out of the muf fler (Fig. 6-14). NOTE: Use only a needlenose pliers. Other pliers or tools may damage the spark arrestor . 3. Clean the spark arrestor with a wir e brush. Replace if damaged or unable to clean thoroughly . 4. Reinstall spark a ...

  • Cub Cadet CC2000 - page 17

    17 Maintenance (continued) CLEANING To avoid serious personal injury , always tur n your trimmer off and allow it to cool befor e you clean or do any maintenance on it. Use a small brush to clean off the outside of the unit. Do not use strong deter gents. Household cleaners that contain aromatic oils such as pine and lemon, and such as kerosene, ca ...

  • Cub Cadet CC2000 - page 18

    18 T roubleshooting Section 7 CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Disassemble, remove the welded section and rewind the line Line twi ...

  • Cub Cadet CC2000 - page 19

    19 Specifications Section 8 Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Cub Cadet CC2000 - page 20

    MANUF ACTURER’S LIMITED W ARRANTY FOR: Cub Cadet LLC r eserves the right to change or impr ove the design of any Cub Cadet Product without assuming any obligation to modify any product pr eviously manufactured. No implied warranty , including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable ...

  • Cub Cadet CC2000 - page 21

    Man uel de l'utilisateur Avertissement : à l'intention des utilisateurs opérant dans les terres forestières des États-Unis et dans les états de Californie, du Maine, de l'Orégon et de Washington. T outes les terres forestières des États-Unis et de l'état de Californie (Codes sur les ressources publiques 4442 et 4443), d ...

  • Cub Cadet CC2000 - page 22

    2 T ABLE DES MA TI È RES Contenu Page Section 1: Sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Section 2 : F amiliarisez-vous a v ec l'appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Section 3 : Montage . . . . . . . ...

  • Cub Cadet CC2000 - page 23

    3 Section 1 Sécurité LIRE TOUTES LES INSTRUCTIONS AV ANT UTILISA TION •V euillez lire les instructions avec soin. Familiarisez-vous avec les commandes et l'utilisation correcte de cet appar eil. • N'utilisez pas l'appareil si vous êtes fatigué, malade ou sous l'effet de l'alcool, de dr ogues ou de médicaments. • ...

  • Cub Cadet CC2000 - page 24

    Sécurité (suite) • Arrêtez toujours le moteur et laissez-le refr oidir avant de re mplir le réservoir de carburant. N'enlevez jamais le bouchon du réservoir et n'ajoutez jamais de carburant pendant que le moteur est chaud. Ne faites jamais fonctionner l'appareil sans que le bouchon de carburant soit bien mis. Desserrez lenteme ...

  • Cub Cadet CC2000 - page 25

    5 Sécurité (suite) SYMBOLES DE SÉCURITÉ ET INTERNA TIONAUX Ce manuel de l'utilisateur décrit les symboles et pictogrammes de sécurité et internationaux pouvant apparaître sur ce produit. Consultez le manuel de l'utilisateur pour les informations concernant la sécurité, le montage, le fonctionnement, l'entretien e t les rép ...

  • Cub Cadet CC2000 - page 26

    6 SYMBOLE SIGNIFICA TION • LAME AIGUISÉE A VER TISSEMENT : le protecteur d'accessoir e de coupe comporte une lame aiguisée. Ne touchez pas la lame pour éviter des blessures graves. • LEVIER D'ÉTRANGLEUR A • Position de DÉMARRAGE. B • Position MARCHE. A VER TISSEMENT : l'utilisation d'outils électriques peut provoqu ...

  • Cub Cadet CC2000 - page 27

    7 Section 2 F amiliarisez-vous avec l’appareil APPLICA TIONS Comme désherbeuse ; • Coupe d'herbe et de mauvaises herbes légères. • Coupe de bordur es •T aille autour des arbres, des clôtur es, etc. Couvercle du filtr e à air Manette des gaz Poignée de l'arbre Bougie Poignée en D Corps de l'arbre Commande Marche/Arrêt ...

  • Cub Cadet CC2000 - page 28

    8 Section 3 Assemblage (4) vis Bride inférieure Fig. 3-1 Fig. 3-2 (4) Écrous 15,24 cm (6 po) minimum Poignée de l'arbre Poignée en D Corps de l'arbre La poignée en D peut être préinstallée sur certains appar eils. Dans ce cas, il suffit de desserr er les vis et ajuster la poignée en fonction de l'opérateur . Passez à l&apo ...

  • Cub Cadet CC2000 - page 29

    9 Section 4 Huile et carburant MÉLANGE D'HUILE ET DE CARBURANT En général, si l'appareil ne fonctionne pas corr ectement, c'est que le carburant est vieux ou mal mélangé. Prenez soin d'utiliser de l’essence sans plomb fraîche et propr e. Suivez à la lettre les instructions de mélange de carburant et d'huile. Défi ...

  • Cub Cadet CC2000 - page 30

    Section 5 Fonctionnement INSTRUCTIONS DE DÉMARRAGE Faites uniquement marcher l’appar eil dans un lieu extérieur bien aéré. Les fumées d'échappement d'oxyde de carbone peuvent être fatales dans un lieu confiné. Évitez tout démarrage accidentel. Mettez-vous en position de démarrage lorsque vous tirez sur la cor de de démarrage ...

  • Cub Cadet CC2000 - page 31

    11 Fonctionnement (suite) TENUE DE LA DÉSHERBEUSE Portez toujours des protections (yeux, or eilles, pieds et corps) pour diminuer les risques de blessures durant l'utilisation de l'appareil. A vant de fair e marcher l'appar eil, tenez-vous en position de fonctionnement (Fig. 5-4). Vérifiez les points suivants: • L'opérateur ...

  • Cub Cadet CC2000 - page 32

    12 Fonctionnement (suite) Fig. 5-6 COUPE DÉCORA TIVE La coupe décorative consiste à déblayer la végétation autour des arbres, des bornes, des clôtures, etc. T our nez entièrement l'appar eil de manière à ce que l'accessoire de coupe soit à un angle de 30° par rapport au sol (Fig. 5-6). Section 6 Entretien REMARQUE : certaines ...

  • Cub Cadet CC2000 - page 33

    13 Entretien (suite) Fig. 6-2 Moulinet intérieur Bobine extérieure Ressort Arbre Dents de positionnement Boucle Fig. 6-4 Fig. 6-5 Fig. 6-3 Utiliser avec du fil de membrane ou du fil simple Tr ous allongés Utiliser avec le fil simple UNIQUEMENT V ous pouvez r emplacer le fil de deux façons : • Rembobinez du fil neuf dans le moulinet intérieur ...

  • Cub Cadet CC2000 - page 34

    14 Entretien (suite) 7. Enroulez les fils en couches uniformes serrées sur le moulinet (Fig. 6-6). Enroulez le fil dans le sens indiqué sur le moulinet intérieur . Placez votre index entr e les deux fils pour les empêcher de se superposer . Ne superposez pas les extrémités du fil. Passez à l’étape 11. Installation du fil de membrane 8. D? ...

  • Cub Cadet CC2000 - page 35

    Entretien (suite) ENTRETIEN DU FIL TRE À AIR Nettoyage du filtre à air Pour éviter des blessures graves, éteignez toujours la désherbeuse et laissez-la refr oidir avant tout nettoyage ou entretien. Nettoyez et relubrifiez le filtr e à air à toutes les 10 heures de fonctionnement. Son entr etien est très important. Si vous ne le faites pas, ...

  • Cub Cadet CC2000 - page 36

    16 Entretien (suite) 2. Utilisez une pince à becs effilés pour saisir le collet du pare-étincelles et r etirez-le du silencieux. (Fig. 6-14). REMARQUE : utilisez uniquement une pince à becs effilés. D'autres pinces ou outils peuvent endommager le pare-étincelles. 3. Nettoyez le pare-étincelles à l'aide d'une br osse métalliq ...

  • Cub Cadet CC2000 - page 37

    17 Entretien (suite) 0.025 inch (0.655 mm) Fig. 6-16 ACCESSOIRES / PIÈCES DE RECHANGE Bougie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 791-181765 P are-étincelles . . . . . . . . . . . . . . . . . . . . . . . . . . . 791-181696 Cartouche de fil de rechange . . . . . . . . . . . . . . . . . . 153-1156 Ressort du moulinet in ...

  • Cub Cadet CC2000 - page 38

    18 Section 7 Dépannage CAUSE SOLUTION Accessoire de coupe engor gé d'herbes Arrêtez le moteur et nettoyez l'accessoire Accessoire de coupe mal aligné Char gez du fil neuf Moulinet intérieur bloqué Remplacez le moulinet Tête de coupe sale Nettoyez le moulinet intérieur et la bobine extérieure Fil soudé Démontez et déposez la pa ...

  • Cub Cadet CC2000 - page 39

    19 Section 8 Caractéristiques T ype de moteur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refroidi par air , 2-temps Cylindrée . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Cub Cadet CC2000 - page 40

    GARANTIE LIMITÉE DU F ABRICANT POUR: Aucune garantie implicite, y compris toute garantie de valeur marchande ou d'adaptation à une fin particulière, ne s'applique après la période applicable de garantie expresse écrite ci-dessus concernant les pièces qui sont identifiées. Aucune autre garantie ou caution expresse, écrite ou orale ...

  • Cub Cadet CC2000 - page 41

    Man ual del Dueño/Oper ador Recor tador de 2 ciclos Modelo CC 2000 Advertencia: Para los usuarios en tierras forestales de los EE.UU. y en los estados de California, Maine, Oregon y Washington. T odos los terrenos forestales de los EE.UU . y en el estado de California (Códigos de Recursos Públicos 4442 y 4443), Oregon y W ashington, requieren, p ...

  • Cub Cadet CC2000 - page 42

    INDICE DE MA TERIAS Contenido Página Sección 1: Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Sección 2: F amiliarícese con su unidad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Sección 3: Ensamblaje . . . . . . . . . . . . ...

  • Cub Cadet CC2000 - page 43

    3 Sección 1 Seguridad LEA TODAS LAS INSTRUCCIONES ANTES DE LA OPERACION • Lea todas las instrucciones con cuidado. Conozca bien los controles y el uso corr ecto de la unidad. •N o opere esta unidad si está cansado, enfermo, o bajo los efectos del alcohol, drogas o medicamentos. • Los niños y los adolescentes menores de 15 años no deben op ...

  • Cub Cadet CC2000 - page 44

    4 Seguridad (continuación) • Guarde el combustible en envases que hayan sido diseñados y aprobados para el almacenamiento de dichos materiales. • Antes de llenar el tanque de combustible, apague siempre el motor y espere que se enfríe. No r etire nunca la tapa del tanque de combustible ni car gue combustible mientras el motor esté caliente. ...

  • Cub Cadet CC2000 - page 45

    5 Seguridad (continuación) SIMBOLOS DE SEGURIDAD E INTERNACIONALES Este manual del operador describe los símbolos y figuras de seguridad e internacionales que pueden aparecer en este producto. Lea el manual del operador para obtener información completa acerca de la seguridad, ensamble, operación y mantenimiento y r eparación. SIMBOLO SIGNIFIC ...

  • Cub Cadet CC2000 - page 46

    6 SIMBOLO SIGNIFICADO • CUCHILLA AFILADA ADVERTENCIA: La pr otección del accesorio de corte contiene una cuchilla afilada. Para prevenir graves lesiones, no toque la cuchilla. • CONTROL DEL OBTURADOR A • Posición de ARRANQUE. B • Posición de MARCHA . • NO USE CUCHILLAS ADVERTENCIA: Para evitar lesiones graves, no conecte ni oper e la u ...

  • Cub Cadet CC2000 - page 47

    7 Sección 2 Conozca su unidad APLICACIONES Como recortador; • Corte de césped y hierbas delgadas. • Recorte de bordes • Recorte decorativo alrededor de árboles, cer cos, etc. T apa del combustible Cubierta del filtro de air e Bastidor del eje Control de encendido y apagado Protector accesorio de corte Accesorio de corte Mango del eje Bují ...

  • Cub Cadet CC2000 - page 48

    8 Sección 3 Armado (4) T or nillos Manija en D Abrazadera inferior Fig. 3-1 Fig. 3-2 (4) T uercas Mínimo de 6 pulgadas (15.24 cm) Bastidor del eje Mango del eje Fig. 3-3 Bastidor del eje Protector accesorio de corte Accesorio de corte Abrazadera En algunas unidades, la manija en D puede estar ya instalada y sólo requier e aflojar los tornillos y ...

  • Cub Cadet CC2000 - page 49

    9 Sección 4 Aceite y combustible INSTRUCCIONES P ARA MEZCLAR EL ACEITE Y EL COMBUSTIBLE El combustible viejo o mal mezclado son los motivos principales del mal funcionamiento de la unidad. Asegúrese de usar combustible nuevo, limpio y sin plomo. Siga las instrucciones en detalle para mezclar correctamente el aceite y el combustible. Definición d ...

  • Cub Cadet CC2000 - page 50

    INSTRUCCIONES DE ARRANQUE Use esta unidad solamente en un lugar al aire libr e con buena ventilación. Los vapores del escape de monóxido de carbono pueden ser mortíferos en un lugar cerrado. 10 Sección 5 Operación Evite arrancar la unidad accidentalmente. Colóquese en posición de inicio siempre que tir e de la cuerda de arranque. Para evitar ...

  • Cub Cadet CC2000 - page 51

    11 Operación (continuación) COMO SOSTENER EL RECORT ADOR Use siempre pr otección para sus ojos, audición, pies y cuerpo para reducir el riesgo de una lesión al operar esta unidad. Antes de operar esta unidad, párese en posición de operación (Fig. 5-4). V erifique lo siguiente: •E l operador tiene protección ocular y ropa adecuada. • El ...

  • Cub Cadet CC2000 - page 52

    12 INST ALACION DE LA LINEA Esta sección cubre la instalación de la línea dividida y de una línea estándar . Use siempre la línea de r epuesto de 0.095 pulgadas (2.41 mm) del fabricante. Usar otro tipo de línea podría causar que el motor recaliente o falle. No use nunca línea reforzada con metal, alambr e, cadena ni soga, etc. Estos elemen ...

  • Cub Cadet CC2000 - page 53

    13 Mantenimiento (continuación) Existen dos métodos para cambiar la línea de corte. • Bobine el carrete interior con línea nueva. • Instale un carrete interior pr ebobinado Bobinado del carrete interior existente 1. Sostenga la bobina exterior con una mano y desenrosque el botón de tope en sentido antihorario (Fig. 6-1). Inspeccione el per ...

  • Cub Cadet CC2000 - page 54

    14 Mantenimiento (continuación) 7. Bobine las líneas en capas par ejas y ajustadas sobre el carrete (Fig. 6-6). Bobine la línea en la dir ección indicada en el carrete interior . Coloque su dedo índice entre las dos líneas para evitar que se superpongan. No superponga los extremos de la línea. Pr oceda al paso 11. Instalación de la línea d ...

  • Cub Cadet CC2000 - page 55

    15 Mantenimiento (continuación) MANTENIMIENTO DEL FIL TRO DE AIRE Limpieza del filtro de air e Para evitar graves lesiones personales, apague siempre su r ecortador y espere que se enfríe antes de limpiarlo o realizar cualquier tipo de mantenimiento. Limpie y vuelva a aceitar el filtro de air e cada 10 horas de operación. Es un elemento importan ...

  • Cub Cadet CC2000 - page 56

    16 Mantenimiento (continuación) 2. Use un alicate puntiagudo para agarrar el cuello del parachispas y hálelo del silenciador . (Fig. 6-14). NOT A: Use alicates puntiagudos únicamente. Cualquier otro alicate o herramienta puede dañar el parachispas. 3. Limpie el parachispas con un cepillo de cerdas metálicas. Cámbielo si está dañado o si no ...

  • Cub Cadet CC2000 - page 57

    17 Mantenimiento (continuación) 0.025 inch (0.655 mm) Fig. 6-16 ACCESORIOS/REPUESTOS Bujía de encendido . . . . . . . . . . . . . . . . . . . . . . . . 791-181765 Amortiguador de chispas . . . . . . . . . . . . . . . . . . .791-181696 Cartucho con línea de repuesto . . . . . . . . . . . . . . . 153-1156 Resorte del carrete interior . . . . . . . ...

  • Cub Cadet CC2000 - page 58

    18 Sección 7 Solución de desperfectos CAUSA ACCION El accesorio de corte está atascado de hierba Pare el motor y limpie el accesorio de corte El accesorio de corte no tiene línea Coloque una línea nueva El carrete interior está trabado Cambie el carrete interior La cabeza de corte está sucia Limpie el carrete interior y la bobina exterior La ...

  • Cub Cadet CC2000 - page 59

    19 Sección 8 Especificaciones T ipo de motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enfriado por aire, de 2 ciclos Desplazamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 pulg. cúbic ...

  • Cub Cadet CC2000 - page 60

    GARANTÍA LIMIT ADA DEL F ABRICANTE P ARA: Ninguna garantía implícita es aplicable, incluyendo cualquier garantía implícita de comerciabilidad o idoneidad para un propósito particular , después del período aplicable de la garantía expresa escrita con anterioridad, con respecto a las piezas identificadas. Exceptuando lo mencionado con anteri ...

Manufacturer Cub Cadet Category Trimmer

Documents that we receive from a manufacturer of a Cub Cadet CC2000 can be divided into several groups. They are, among others:
- Cub Cadet technical drawings
- CC2000 manuals
- Cub Cadet product data sheets
- information booklets
- or energy labels Cub Cadet CC2000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cub Cadet CC2000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cub Cadet CC2000, service manual, brief instructions and user manuals Cub Cadet CC2000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cub Cadet CC2000.

Similar manuals

A complete manual for the device Cub Cadet CC2000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cub Cadet CC2000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cub Cadet CC2000.

A complete Cub Cadet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cub Cadet CC2000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cub Cadet CC2000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cub Cadet CC2000, that we can find in the current document
3. Tips how to use the basic functions of the device Cub Cadet CC2000 - which should help us in our first steps of using Cub Cadet CC2000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cub Cadet CC2000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cub Cadet CC2000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cub Cadet CC2000?

Use the form below

If you did not solve your problem by using a manual Cub Cadet CC2000, ask a question using the form below. If a user had a similar problem with Cub Cadet CC2000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)