Manual DeWalt 31-735

76 pages 2.57 mb
Download

Go to site of 76

Summary
  • DeWalt 31-735 - page 1

    www .deltamachinery .com (800) 223-7278 - US (800) 463-3582 - CANADA 6" Belt/12" Disc Abrasive Finishing Machine Instruction Manual Manuel d’utilisation Manual de instrucciones 31-735 FRANÇAIS (27) ESP AÑOL (52) A21536 - 02-07-07 Copyright © 2007 Delta Machinery Appareil de finition abrasif à disque de 305 mm (12 po)/à courroie de ...

  • DeWalt 31-735 - page 2

    2 T ABLE OF CONTENTS IMPOR T ANT SAFETY INSTRUCTIONS Read and understand all warnings and operating instructions before using any tool or equipment. Always follow basic safety precautions to r educe the risk of personal injury . Improper operation, maintenance, or modification of tools or equipment could result in serious injury and pr operty damag ...

  • DeWalt 31-735 - page 3

    3 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will greatly minimize the possibility of accidents and injury . 2. WEAR EYE AND HEARING PROTECTION. AL WA YS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED SAFE ...

  • DeWalt 31-735 - page 4

    4 Failure to follow these rules may r esult in serious personal injury . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injur ...

  • DeWalt 31-735 - page 5

    5 Fig. A Fig. B GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a time delay fuse. NOTE: Time delay fuses sh ...

  • DeWalt 31-735 - page 6

    6 4. Permanently connected machines: If the machine is intended to be permanently connected, all wiring must be done by a qualified electrician and conform to the National Electric Code and all local codes and ordinances. Fig. C GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES EXTENSION CORDS Use proper extens ...

  • DeWalt 31-735 - page 7

    7 FOREWORD FUNCTIONAL DESCRIPTION NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual ar e repr esentative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique only . UNP ACKING AND CLEANING Carefully unpack the machine and all ...

  • DeWalt 31-735 - page 8

    8 ASSEMBL Y ASSEMBL Y TOOLS REQUIRED ASSEMBL Y TIME ESTIMA TE Assembly for this machine takes approximately 1 to 2 hours. For your own safety , do not connect the machine to the power source until the machine is completely assembled and you read and understand the entir e instruction manual. 1/4" Wr ench 5/16" Wr ench 3/8" Wr ench Ad ...

  • DeWalt 31-735 - page 9

    9 9. Insert a 5/16-18x4" hex head screw (G) Fig. 4 thr ough the hole (F) Fig. 3, the two holes (E) in the caster assembly , and the other hole (F) in the pivot bracket. Thread a 5/16-18 lock nut on the scr ew . Tighten securely . 10. Align the two holes (H) Fig. 5 in the foot lever with the two holes (J) in the pivot bracket. 11. Attach the fo ...

  • DeWalt 31-735 - page 10

    10 A TT ACHING THE SANDING UNIT TO THE CABINET The belt/disc sander is heavy . Use two or more people to lift the unit to the top of the cabinet. 1. Place the sanding unit on top of the cabinet. NOTE: Insert the sander drive belt through the hole (A) FIG. 11. 2. Place a 5/16" lock washer on a 5/16-18 x 1/2" hex head screw . From inside th ...

  • DeWalt 31-735 - page 11

    11 INST ALLING THE BEL T ON THE MOTOR 1. Remove the two screws (A) Fig. 15 from the top of the sanding unit and r emove the plate (B). 2. Check to see that the belt (C) Fig. 16 is in the groove of the pulley (D) of the sanding unit. 3. Lift the motor (F) Fig. 17 and place the belt (C) on the motor pulley (G). 4. Slowly lower the motor (F) Fig. 17 t ...

  • DeWalt 31-735 - page 12

    12 1. Place a hose clamp (A) Fig. 20 on each end of the out-take hose (B). 2 . Slide one end of hose (B) Fig. 21 over the dust collector out-take port (C) and secure it with the hose clamp (A). 3. Slide the other end of the hose (B) Fig. 22 over the dust chute (D) on the inside of the back panel of the cabinet. Secure it with the hose clamp (A). 4. ...

  • DeWalt 31-735 - page 13

    13 9. Align the sanding table guide (J) Fig. 25 with cutout (K) on the side of the sanding belt frame. 10. Thread the sanding ratchet lever/stud assembly (L) Fig. 26 thr ough the sanding table slot (N) Figs. 25 and 26, and into the tapped hole (M) Fig. 26 in the side of the sanding frame. NOTE: Thread the sanding table ratchet lever/stud assembly a ...

  • DeWalt 31-735 - page 14

    14 4. Place a 7/16" flat washer (C) Fig. 30 on each stud, then a 1/2" spring (D). 5. Thread the lock handle (E) on the right side stud. Tighten securely to hold the disc sander table in place. 6. Align the hole in the pointer (A) Fig. 31 with the tapped hole (D) in the the left side table clamp. 7. Thr ead a 1/4-20 x 1/4" round head ...

  • DeWalt 31-735 - page 15

    15 A TT ACHING THE DUST COLLECTOR BAG 1. Insert the dust collector bag hanger (A) Fig. 34 in the two holes (B) in the top of the cabinet. 2. Place the end of the dust collector bag (C) Fig. 35 over the dust collector hanger (A). 3. Place a hose clamp (D) Fig. 36 over the intake port of the dust collector bag (C). Slide the intake port of the dust c ...

  • DeWalt 31-735 - page 16

    16 ADJUSTING THE TENSION AND TRACKING OF THE SANDING BEL T Y our machine is shipped without belt tension. Before operating the machine, tension the belt properly and ensure that the belt is tracking corr ectly . 1. Loosen the two lock knobs (A) Fig. 39 and remove the top cover (B). 2. T ur n the belt tension handle (C) Fig. 40 counter -clockwise to ...

  • DeWalt 31-735 - page 17

    17 SETTING THE T ABLE 90 ° TO THE BEL T 1. Loosen the table-tilting ratchet lever (A) Fig. 43. T urn the stop (B) to the left and rotate the table (C) Fig. 44 until the trunnion (D) Fig. 43 contacts the stop (B). Tighten the lock handle (A). NOTE: The lock handle (A) is spring-loaded and can be repositioned by pulling out the handle, moving it, an ...

  • DeWalt 31-735 - page 18

    18 CHANGING THE POSITION OF THE SANDING ARM 1. Y ou can use the sanding arm in any angle from the vertical position (Fig. 48) to the horizontal position (Fig. 49). Loosen the lock lever (B), position the arm (A) to the desired angle, and tighten the lock lever (B). 2. Y ou can remove the top idler pulley cover (C) Figs. 48 and 49 to clear the workp ...

  • DeWalt 31-735 - page 19

    19 SETTING THE DISC T ABLE MITER GAUGE SLOT P ARALLEL TO THE SANDING DISC Maintain a maximum distance of 1/16" between the sanding disc and the table. Disconnect the machine from the power sour ce! 1. With the table (A) Fig. 52 positioned 90 ° to the disc, place a square (B) in the miter gauge slot with the blade of the square touching the sa ...

  • DeWalt 31-735 - page 20

    20 MACHINE USE ABRASIVE BEL TS & DISCS - THEIR SELECTION AND USE Delta supplies a wide range of belts and discs for use on your Belt and Disc Finishing Machine. Y ou can use these belts and discs for a wide range of work on wood, metals, plastics and other materials. However , when you have a lar ge amount of production work of one kind, refer ...

  • DeWalt 31-735 - page 21

    21 SANDING INSIDE CURVES Disconnect the machine from the power sour ce! 1. Loosen the two lock knobs (A) Fig. 58 and remove the top cover (B). 2. Inside curves can be sanded on the top sanding drum (Fig. 59). Replace the top cover (B) Fig. 58 when done. Fig. 59 A B Fig. 58 When you sand the ends of wide workpieces, use the sanding arm in the vertic ...

  • DeWalt 31-735 - page 22

    22 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc as shown in Fig. 62. Y ou must position the edge of the table a maximum of 1/16" away from the sanding belt to avoid trapping the workpiece or your fingers between the table and the sanding belt. CIRCLE SANDING WITH DISC A circle sanding attachment is ...

  • DeWalt 31-735 - page 23

    23 2. Loosen the two lock knobs (C) Fig. 68 enough to allow the back panel (D) Figs. 67, 68, and 69 to open. NOTE: The lock knobs (C) cannot be removed. 3. Release the belt tension by tur ning the hand lever (E) Fig. 67. Remove the belt (F) Fig. 69 from both sanding drums. 4 . Install the new sanding belt over both sanding drums. Ensure that the be ...

  • DeWalt 31-735 - page 24

    24 KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. F AILURE TO ST ART Should your m achine fail to start, check to make sure the pr ongs on the cord ...

  • DeWalt 31-735 - page 25

    25 SERVICE AND REP AIRS All quality tools will eventually requir e servicing and/or replacement of parts. For information about Delta Machinery , its factory- owned branches, or an Authorized W arranty Service Center , visit our website at www .deltamachinery .com or call our Customer Care Center at 1-800-223-7278. All r epairs made by our service ...

  • DeWalt 31-735 - page 26

    26 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized ser ...

  • DeWalt 31-735 - page 27

    27 MESURES DE SÉCURITÉ - DÉFINITIONS Ce guide contient des renseignements importants que vous deviez bien saisir . Cette information porte sur VOTRE SÉCURITÉ et sur LA PRÉVENTION DE PROBLÈMES D’ÉQUIPEMENT . Afin de vous aider à identifier cette information, nous avons utilisé les symboles ci-dessous. V euillez lire attentivement ce guid ...

  • DeWalt 31-735 - page 28

    28 14. UTILISER LE CORDON PROLONGA TEUR APPROPRIÉ. S’assurer que le cor don prolongateur est en bon état. Lorsqu’un cordon pr olongateur est utilisé, s’assurer que celui-ci est d’un calibre suf fisant pour l’alimentation nécessaire à la machine. Un cordon d’un calibr e insuffisant entraînera une perte de tension d’où une perte ...

  • DeWalt 31-735 - page 29

    29 RÈGLES SPÉCIFIQUES ADDITIONNELLES DE SÛRETÉ L ’inobservation de ces règles peut conduir e à des blessur es graves. CONSERVER CES DIRECTIVES. Les consulter souvent et les utiliser pour donner des dir ectives aux autres. 1. NE P AS F AIRE FONCTIONNER CET APP AREIL avant qu’il ne soit entièrement assemblé et installé conformément à c ...

  • DeWalt 31-735 - page 30

    30 RACCORDEMENTS ÉLECTRIQUES Un circuit électrique séparé doit êtr e utilisé pour les machines. Ce circuit doit utiliser un câble de calibre 12 au minimum et doit être protégé par un fusible temporisé. REMARQUE : les fusibles temporisés devraient avoir l’inscription « D » au Canada et « T » aux É.-U. Si on utilise un cordon pr ol ...

  • DeWalt 31-735 - page 31

    31 CORDON DE RALLONGE Employez les cordes appropriées de pr olongation. S'assurent votr e corde de prolongation est en bon état. En utilisant une cor de de prolongation, soyez sûr d'employer un assez lour d pour porter le courant de la machine. Une corde tr op petite causera une baisse dans la tension secteur , ayant pour résultat la ...

  • DeWalt 31-735 - page 32

    DESCRIPTION FONCTIONNELLE A V ANT -PROPOS DÉSEMBALLAGE ET NETTOY AGE Désemballer soigneusement la machine et toutes les pièces de ou des emballage(s) d’expédition. Retirer l’huile anticor - rosion des surfaces non peintes à l’aide d’un chif fon doux humidifié avec de l’alcool, du diluant à peinture ou de l’alcool dénaturé. N’ ...

  • DeWalt 31-735 - page 33

    33 ASSEMBLAGE Pour votre pr opre sûr eté, ne reliez pas la machine à la source d'énergie jusqu'à ce que la machine soit complètement assemblée et vous lisez et comprenez le manuel d'instruction entier . L'ESTIMA TION DE TEMPS D'ASSEMBLEE L ’Assemblée pour cette machine pr end une à deux heures. Clé de 1/4 po Cl? ...

  • DeWalt 31-735 - page 34

    34 9. Insér er une vis à tête hexagonale de 5/16 po-18 x 4 po (G), fig. 4, dans le trou (F), fig. 3, les deux trous de l’ensemble de roulettes (E) et dans l’autr e trou (F) pratiqué dans le support pivotant. Visser un contr e-écrou de 5/16 po-18 sur la vis. Serr er solidement. 10. Aligner les deux trous (H), fig. 5, pratiqués dans la péd ...

  • DeWalt 31-735 - page 35

    35 FIXA TION DE L'OUTIL DE PONÇAGE AU BOÎTIER La ponceuse à courroie/à disque est lour de. Faire appel au moins à deux personnes pour soulever l'appareil sur le dessus du boîtier . 1. Mettre la ponceuse sur le dessus du boîtier . REMARQUE : insérer la courr oie d'entraînement de la ponceuse dans le trou (A) FIG. 11. 2. Mettr ...

  • DeWalt 31-735 - page 36

    36 INST ALLA TION DE LA COURROIE SUR LE MOTEUR 1. Enlever les deux vis (A), fig. 15, logées au sommet de l'appar eil de ponçage, puis enlever la plaque (B). 2. S'assur er que la courroie (C), fig. 16, repose dans la rainur e de la poulie (D) de l'appareil de ponçage. 3. Soulever le moteur (F), fig. 17, et mettr e la courroie (C) s ...

  • DeWalt 31-735 - page 37

    37 1 . Insérer un collier de serrage (A), fig. 20, à chaque extrémité du tuyau de sortie (B). 2. Glisser une extrémité du tuyau (B), fig. 21, au-dessus de l'orifice de sortie du dépoussiéreur (C), puis la fixer solidement avec le collier de serrage (A). 3. Glisser l'autre extrémité du tuyau (B), fig. 22, au-dessus de la goulotte ...

  • DeWalt 31-735 - page 38

    38 9. Aligner le guide de la table de ponçage (J), fig. 25, avec l'entaille (K) pratiquée sur le côté du cadre de la bande abrasive. 10. Visser le levier à cliquet de ponçage/ensemble de goujons (L), fig. 26, dans la fente de la table de ponçage (N), fig. 25 e t 26, et dans le trou taraudé (M), fig. 26, pratiqué sur le côté du cadr ...

  • DeWalt 31-735 - page 39

    39 4. Enfiler une rondelle plate de 7/16 po (C), fig. 30, sur chaque goujon, puis un ressort de 1/2 po (D). 5. Visser la poignée de verrouillage (E) sur le goujon du côté dr oit, puis bien serrer afin de maintenir en place la table de p onceuse à disque. 6. Aligner le trou du pointeur (A), fig. 31, avec le trou taraudé (D) pratiqué dans la br ...

  • DeWalt 31-735 - page 40

    40 FIXA TION DU SAC À POUSSIÈRE 1. Insérer le support du sac à poussièr e (A), fig. 34, dans les deux trous (B) logés au sommet du boîtier . 2. Mettre l'extrémité du sac à poussière (C), fig. 35, au- dessus du support du dépoussiéreur (A). 3. Insérer un collier de serrage (D), fig. 36, au-dessus de l'orifice d'admission ...

  • DeWalt 31-735 - page 41

    41 AJUSTER LA TENSION ET TRAQUER DE LA CEINTURE DE COURROIE La courroie de l'appar eil expédié n'est pas tendue. Avant de fair e fonctionner l'appareil, bien tendr e la courroie et s'assur er que son centrage est adéquat. 1. Desserrer les deux boutons de verrouillage (A), fig. 39, et enlever le couvercle supérieur (B). 2. T ...

  • DeWalt 31-735 - page 42

    42 RÉGLAGE DE LA T ABLE À 90° P AR RAPPORT À LA COURROIE 1. Desserrer le levier à cliquet d'inclinaison de la table (A) fig. 43. T ourner la butée (B) à gauche, puis tour ner la table (C), fig. 44, de manière à ce que le tourillon (D), fig. 43, entr e en contact avec la butée (B). Serrer la poignée de verrouillage (A). REMARQUE : la ...

  • DeWalt 31-735 - page 43

    43 MODIFICA TION DE LA POSITION DU BRAS DE LA PONCEUSE 1. Il est possible d'utiliser le bras de ponçage selon tout angle donné de la verticale (fig. 48) à l'horizontal (fig. 49). Desserrer le levier de blocage (B), positionner le bras (A) à l'angle voulu, puis serrer le levier de blocage (B). 2. V ous pouvez enlever le couvercle ...

  • DeWalt 31-735 - page 44

    44 RÉGLAGE DU P ARALLÉLISME DE LA FENTE DU GUIDE D'ONGLETS DE LA T ABLE À DISQUE A VEC LE DISQUE ABRASIF Maintenir une distance maximale de 1/16 po entre le disque abrasif et la table. 1. La table (A), fig. 52, étant à un angle de 90° avec le disque, mettre une équerre (B) dans la fente du guide d'onglets de ma nièr e à ce que la ...

  • DeWalt 31-735 - page 45

    45 COURROIES ET DISQUES ABRASIFS - SÉLECTION ET UTILISA TION Delta offr e une vaste gamme de courroies et de disques à utiliser sur votre appar eil de finition à courroie et à disque. Ces co urr oies et disques peuvent servir pour un large éventail de pr ojets (bois, métaux, plastique et autres matériaux). T outefois, dans le c as d'un ...

  • DeWalt 31-735 - page 46

    46 PONÇAGE DES COURBES INTÉRIEURES 1. Desserrer les deux boutons de verrouillage (A), fig. 58, puis enlever le couver cle supérieur (B). 2. Les courbes intérieures peuvent être poncées au sommet du cylindr e de contact (fig. 59). Remettre le couver cle supérieur (B), fig. 56A, après avoir terminé. Fig. 59 A B Fig. 58 Pour poncer les extré ...

  • DeWalt 31-735 - page 47

    47 PONÇAGE D'EXTRÉMITÉ A VEC LE DISQUE Pour le ponçage des extrémités de pièces étroites, utiliser le disque abrasif comme le montre la fig. 62. PONÇAGE DE CERCLE A VEC DISQUE Un accessoire de ponçage de cer cle est four ni avec la ponceuse. Cela vous permet de poncer des cer cles ayant un diamètre maximal de 61 cm (24 po). Utilisat ...

  • DeWalt 31-735 - page 48

    48 REMPLACEMENT DE LA BANDE ABRASIVE 1. Desserrer les deux boutons de verrouillage (A), fig. 67, puis enlever le couvercle supérieur (B). 2. Desserrer les deux boutons de verr ouillage (C), fig. 68, suffisamment pour permettr e au panneau arrière (D), fig. 63, 64 et 65, d'ouvrir . REMARQUE : les boutons de verrouillage (C) ne peuvent êtr e ...

  • DeWalt 31-735 - page 49

    GARDER LA MACHINE PROPRE Dégager régulièrement toutes les conduites d’air avec de l’air comprimé sec. T outes les pièces en plastique doivent être nettoyées à l’aide d’un chiffon doux humide. NE JAMAIS utiliser de solvants pour nettoyer les pièces en plastique. Les solvants peuvent dissoudr e ou endom- mager le matériel. PIÈCES D ...

  • DeWalt 31-735 - page 50

    50 ENTRETIEN ET RÉP ARA TION T ous les outils de qualité finissent par demander un entretien ou un changement de pièce. Pour de plus amples r enseignements à propos de Delta Machinery , ses succursales d’usine ou un centre de réparation sous garantie autorisé, consulter notre site W eb au www .deltamachinery .com ou composer le 1-800-223-72 ...

  • DeWalt 31-735 - page 51

    51 GARANTIE Pour enregistr er votr e outil pour la garantie service la visite notre site W eb à www .deltamachinery .com. Garantie limitée de deux ans Delta réparera ou r emplacera, à ses frais et à sa discrétion, toute nouvelle machine Delta, pièce de rechange ou tout accessoire qui, dans des circonstances d'utilisation normale, s&apos ...

  • DeWalt 31-735 - page 52

    52 Lea y entienda todas advertencias y las instrucciones operadoras antes de utilizar cualquier instrumento o el equipo. Cuando se usa instrumentos o equipo, las precauciones básicas de la seguridad siempre se deben seguir para r educir el riesgo de la herida personal. La operación impropia, la conservación o la modificación de instrumentos o e ...

  • DeWalt 31-735 - page 53

    53 NORMAS GENERALES DE SEGURIDAD 1. P ARA SU PROPIA SEGURIDAD, LEA EL MANUAL DE INSTRUCCIONES ANTES DE UTILIZAR LA MÁQUINA. Al aprender la aplicación, las limitaciones y los peligr os específicos de la máquina, se minimizará enormemente la posibilidad de accidentes y lesiones. 2. USE PROTECCIÓN DE LOS OJOS Y DE LA AUDICIÓN. USE SIEMPRE ANTEO ...

  • DeWalt 31-735 - page 54

    54 NORMAS ESPECÍFICAS ADICIONALES DE SEGURIDAD Si no se siguen estas normas, el resultado podría ser lesiones personales graves. GUARDE EST AS INSTRUCCIONES. Refiérase a ellas con frecuencia y utilícelas para adiestrar a otr os. 1. NO OPERE EST A MÁQUINA hasta que no esté armada e instalada completamente, según las instrucciones. Una máquin ...

  • DeWalt 31-735 - page 55

    55 1. T odas las máquinas conectadas con cordón conectadas a tierra: En caso de mal funcionamiento o avería, la conexión a tierra pr oporciona una ruta de r esistencia mínima para la corriente eléctrica, con el fin de reducir el riesgo de descar gas eléctricas. Esta máquina está equipada con un cordón eléctrico que tien e un conductor de ...

  • DeWalt 31-735 - page 56

    56 Utilice cordones de extensión apropiados. Asegúr ese de que el cordón de extensión esté en buenas condiciones y de que sea un cordón de extensión de tres alambr es que tenga un enchufe de tipo de conexión a tierra con tres terminales y un r eceptáculo coincidente que acepte el enchufe de la máquina. Cuando utilice un cordón de extensi ...

  • DeWalt 31-735 - page 57

    57 DESCRIPCIÓN FUNCIONAL CONTENIDO DE CAR TON NOT A: El cuadro en la cubierta ilustra el modelo actual de la pr oducción. T odas las demas ilustraciones son solamente repr esentativas y es posible que no muestr en el color , el etiquetado y los accesorios reales. PROLOGO Desembale cuidadosamente la máquina y todos los elementos sueltos del o los ...

  • DeWalt 31-735 - page 58

    58 HERRAMIENT AS DE ENSAMBLAJE REQUERIDAS ESTIMACIÓN DEL TIEMPO DE ENSAMBLAJE La asamblea para esta máquina toma aproximadamente 1 a 2 horas. Llave de 1/4" Llave de 5/16" Llave de 3/8" Llave ajustable Pinzas Destornillador Phillip ACOPLE DEL ENSAMBLE DE LA RUEDA AL GABINETE DEL MOTOR 1. Coloque el gabinete del motor de costado (Fig ...

  • DeWalt 31-735 - page 59

    59 9. Inserte un tor nillo de cabeza hexagonal de 5/16-18x4" (G) Fig. 4 a través del orificio (F) Fig. 3, los dos orificios (E) del ensamble de la rueda y el otro orificio (F) del soporte giratorio. Enr osque una tuerca de seguridad de 5/16-18 en el tornillo. Ajuste bien. 10. Alinee los dos orificios (H) Fig. 5 de la palanca de pedal con los ...

  • DeWalt 31-735 - page 60

    60 ACOPLE DE LA UNIDAD DE LIJADO AL GABINETE La lijadora de banda/disco es pesada. Utilice dos o más personas para levantar la unidad hasta la parte superior del gabinete 1. Coloque la unidad de lijado sobre la parte superior del gabinete. NOT A: Inserte la correa impulsora a través del orificio (A) FIG. 11. 2. Coloque una arandela de bloqueo de ...

  • DeWalt 31-735 - page 61

    61 INST ALACIÓN DE LA CORREA EN EL MOTOR 1. Retire los dos tornillos (A) Fig. 15 de la parte superior de la unidad de lijado y quite la placa (B). 2. V erifique que la correa (C) Fig. 16 se encuentre en la ranura de la polea (D) de la unidad de lijado. 3. Levante el motor (F) Fig. 17 y coloque la correa (C) en la polea del motor (G). 4. Baje el mo ...

  • DeWalt 31-735 - page 62

    62 1. Coloque una abrazadera para manguera (A) Fig. 20 en cada extremo de la manguera de salida (B). 2. Deslice un extremo de la manguera (B) Fig. 21 sobre el orificio de salida del colector de polvo (C) y asegúrelo con la abrazadera para manguera (A). 3 . Deslice el otro extremo de la manguera (B) Fig. 22 sobre el conducto para polvo (D) que se e ...

  • DeWalt 31-735 - page 63

    63 9. Alinee la guía del banco de lijado (J) Fig. 25 con el corte (K) que se encuentra al costado del marco de la banda de lijado. 10. Enr osque el ensamble del espárrago/palanca de trinquete para lijado (L) Fig. 26 a través de la ranura del banco para lijado (N) Figs. 25 y 26 y en el orificio roscado (M) Fig. 26 del costado del mar co de lijado ...

  • DeWalt 31-735 - page 64

    64 4. Coloque una arandela plana de 7/16" (C) Fig. 30 en cada espárrago y luego un resorte de 1/2" (D). 5. Enrosque el mango de bloqueo (E) que se encuentra en el espárrago del lado derecho y ajuste bien a fin de mantener el banco para lijadora de disco en su lugar . 6. Alinee el orificio del indicador (A) Fig. 31 con el orificio roscad ...

  • DeWalt 31-735 - page 65

    65 COLOCACIÓN DE LA BOLSA RECOLECTORA DE POL VO 1. Inserte el sujetador de la bolsa recolectora de polvo (A) Fig. 34 en los dos orificios (B) de la parte superior del gabinete. 2. Coloque el extremo de la bolsa r ecolectora de polvo (C) Fig. 35 sobre el sujetador del r ecolector de polvo (A). 3. Coloque una abrazadera para manguera (D) Fig. 36 sob ...

  • DeWalt 31-735 - page 66

    66 AJUSTE DE LA TENSION Y DESPLACE DEL BANDA Su máquina se envía sin tensión de la banda. Antes de hacer funcionar la máquina, tense la banda adecuadamente y asegúrese de que la banda se desplace corr ectamente 1. Afloje las dos perillas de bloqueo (A) Fig. 39 y retire la cubierta superior (B). 2. Gire el mango de tensión de la banda (C) Fig. ...

  • DeWalt 31-735 - page 67

    67 COLOCACIÓN DEL BANCO A 90 GRADOS DE LA BANDA 1. Afloje la palanca de trinquete para inclinar el banco (A) Fig. 43. Gire el tope (B) hacia la izquierda y gir e el banco (C) F ig. 44 hasta que el muñón (D) Fig. 43 entre en contacto con el tope (B). Ajuste el mango de bloqueo (A). NOT A: La palanca de tensión (A) funciona a resorte y puede volv ...

  • DeWalt 31-735 - page 68

    68 CAMBIO DE LA POSICIÓN DEL BRAZO DE LIJADO 1. Puede utilizar el brazo de lijado en cualquier ángulo desde la posición vertical (Fig. 48) hasta la posición horizontal (Fig. 49). Afloje la palanca de bloqueo (B), coloque el brazo (A) en el ángulo deseado y ajuste la palanca de bloqueo (B). 2. Puede retirar la cubierta superior de la polea inte ...

  • DeWalt 31-735 - page 69

    69 FIJACIÓN DE LA RANURA DEL CALIBRADOR DE INGLETE DEL BANCO P ARA DISCO EN FORMA P ARALELA AL DISCO DE LIJAR Mantenga una distancia máxima de 1,6 mm (1/16") entre el disco de lijar y el banco . 1. Con el banco (A) Fig. 52 ubicado a 90° del disco, coloque una escuadra (B) en la ranura del calibrador de inglete de manera que el filo de la es ...

  • DeWalt 31-735 - page 70

    70 BANDAS Y DISCOS ABRASIVOS: SELECCIÓN Y USO LIJADO DE SUPERFICIES O BORDES CON LA BANDA DE LIJADO Al lijar superficies (Fig. 56) o bordes (Fig. 57) utilice el brazo de lijado en posición horizontal. Utilice el banco (A) Fig. 56 y Fig. 57para evitar que la banda arrastre la pieza de trabajo. Sostenga la pieza de trabajo con firmeza y mantenga lo ...

  • DeWalt 31-735 - page 71

    71 LIJADO DE CURV AS INTERNAS 1. Afloje las dos perillas de bloqueo (A) Fig. 58 y retire la cubierta superior (B). 2. Las curvas inter nas pueden lijarse sobre el tambor de lijado superior (Fig. 59). Cuando finalice, vuelva a colocar la cubierta superior (B) Fig. 58. Fig. 59 A B Fig. 58 Cuando lije las terminaciones de piezas de trabajo anchas, uti ...

  • DeWalt 31-735 - page 72

    72 LIJADO DE TERMINACIONES CON EL DISCO Al lijar las terminaciones de piezas de trabajo angostas, utilice el disco de lijar como se muestra en la Fig. 62. Debe colocar el borde del banco a una distancia máxima de 1,6 mm (1/16") de la banda de lijado para evitar que la pieza de trabajo o sus dedos queden atrapados entre el banco y la banda de ...

  • DeWalt 31-735 - page 73

    73 MAINTENANCE REEMPLAZO DE LA BANDA DE LIJADO 1. Afloje las dos perillas de bloqueo (A) Fig. 67 y r etire la cubierta superior (B). 2. Afloje las dos perillas de bloqueo (C) Fig. 68 lo suficiente para permitir que el panel posterior (D) Figs. 67, 68 y 69 se abra. NOT A: No es posible retirar las perillas de bloqueo (C). 3. Release the belt tension ...

  • DeWalt 31-735 - page 74

    74 PIEZAS DE REPUESTO Utilice sólo piezas de repuesto idénticas. Para obtener una lista de piezas o para solicitar piezas, visite nuestr o sitio web e n servicenet.deltamachinery .com . T ambién puede solicitar piezas en nuestro centr o más cercano, o llamando a nuestro Centr o de atención al cliente al 1-800-223-7278 para obtener asistencia p ...

  • DeWalt 31-735 - page 75

    75 EJE DESMONT ABLE ELÉCTRICO 1. El extremo inferior del brazo de la banda de lijado cuenta con un eje desmontable eléctrico. 2. Para acceder al eje desmontable eléctrico, retire los dos tornillos (B) Fig. 71, y luego retir e la cubierta (C). 3. La figura 72 muestra el eje desmontable eléctrico (A). Los ejes giratorios sin cubierta (A) Fig. 72 ...

  • DeWalt 31-735 - page 76

    76 GARANTIA Para registrar la herramienta para obtener el mantenimiento cubierto por la garantía de la herramienta, visite nuestr o sitio we b en www .deltamachinery .com. Garantía limitada de dos años para pr oductos nuevos Delta reparará o r eemplazará, a expensas y opción propias, cualquier máquina nueva, pieza de máquina nueva o accesor ...

Manufacturer DeWalt Category Sander

Documents that we receive from a manufacturer of a DeWalt 31-735 can be divided into several groups. They are, among others:
- DeWalt technical drawings
- 31-735 manuals
- DeWalt product data sheets
- information booklets
- or energy labels DeWalt 31-735
All of them are important, but the most important information from the point of view of use of the device are in the user manual DeWalt 31-735.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals DeWalt 31-735, service manual, brief instructions and user manuals DeWalt 31-735. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product DeWalt 31-735.

Similar manuals

A complete manual for the device DeWalt 31-735, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use DeWalt 31-735 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of DeWalt 31-735.

A complete DeWalt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual DeWalt 31-735 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the DeWalt 31-735, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the DeWalt 31-735, that we can find in the current document
3. Tips how to use the basic functions of the device DeWalt 31-735 - which should help us in our first steps of using DeWalt 31-735
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with DeWalt 31-735
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of DeWalt 31-735 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning DeWalt 31-735?

Use the form below

If you did not solve your problem by using a manual DeWalt 31-735, ask a question using the form below. If a user had a similar problem with DeWalt 31-735 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)