Manual IBM AT-FS202SC/FS1

44 pages 0.58 mb
Download

Go to site of 44

Summary
  • IBM AT-FS202SC/FS1 - page 1

    AT-FS201 AT-FS202 AT-FS202SC/FS1 AT-FS202SC/FS2 AT-FS202SC/FS3 AT-FS202SC/FS4 Fast Ethernet Series Switches Installation Guide PN 613-10761-00 Rev E ...

  • IBM AT-FS202SC/FS1 - page 2

    Copyri ght © 2004 Allied Telesyn In ternational, Corp. All rights reserved. No part of this pu blication may be repr oduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trad emark of Xerox Corporation. All ot her product names, company names, logos or other designatio ns mentioned herein are tr ...

  • IBM AT-FS202SC/FS1 - page 3

    iii Electrical Safety and Emission Compliance Statement Standards : This product meets the f ollowing standards. RFI Emission EN55022 Class A  1 Warning : In a domestic environment this product m ay cause radio interference in which case the u ser may be required to take ad equate measures.  2 Immunity EN55024  3 Warning : This product req ...

  • IBM AT-FS202SC/FS1 - page 4

    Electrical Safety and Emission Compliance Statement iv Important : Appendix B contains translated safety statements for installing this equipment. When yo u see the  , go to Appendix B for the translated safety statement in your language. Wichtig : Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn Sie ? ...

  • IBM AT-FS202SC/FS1 - page 5

    v Table of Contents Electrical Safety and Emi ssion Complian ce Statement ............. ......... iii Welcome to Allied Telesyn ............ ........... ........... ............ ........... ........... ..... vii Where to Find Web-based Guides ................... ........... ........... ............ ........... .. vii Document Conventions .. ....... ...

  • IBM AT-FS202SC/FS1 - page 6

    Table of Contents vi Chapter 3 Troublesho oting ............. ........... ............ ........... ........... ........... .............. ........ 19 Appendix A Technical Specifications . ........... ........... ............ ........... ........... .............. ..... 21 Physical ............. .............. ............ ........... ........... .. ...

  • IBM AT-FS202SC/FS1 - page 7

    vii This guide contai ns instructions on how to install the AT-FS20x and AT-FS202SC/FSx Series switches. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent docu mentation, software, and technical information for all of our products. Fo r product guides, select “Supp ...

  • IBM AT-FS202SC/FS1 - page 8

    Welcome to Allied Telesyn viii Contacting Allied Telesyn This section provides Allied Telesyn co ntact informa tion for technical support as well as sales or corporate information. Online Support You can request technical s upport on line by accessing the Allied Telesyn Knowledge Base from th e following web site: www.alliedtelesyn.com/kb . You can ...

  • IBM AT-FS202SC/FS1 - page 9

    1 Chapter 1 Description The AT-FS20x and AT-FS202SC/FSx Seri es Switches include the following models: The AT-FS20x Series switches are design ed to extend the distance of your network by converting Fas t Ethernet data between twisted-pair cabling and either multimode or single -mode fiber optic cabling. These dual-port switches can also be used to ...

  • IBM AT-FS202SC/FS1 - page 10

    Description 2 Figure 1 illustrates the front panel of an AT-FS20x Series switch. Figure 1 AT-FS20x Series Front Panel (AT-FS202 Model) Figure 2 illustrates a front panel of an AT-FS202SC/FSx Series switch. Figure 2 AT-FS202SC/FSx Series Front Panel (AT-FS202SC/FS4 Model) The back panel of the AT-FS20x and AT-FS202SC/FSx Series switches features a p ...

  • IBM AT-FS202SC/FS1 - page 11

    AT-FS20x Series Installation Guide 3 Table 1 lists the maximum operating distances for the switches. Table 1 Maximum Operating Distances Model 100Base-FX 10/100Base-TX Connector Maximum Operating Distance 1 1. Maximum distance for 1 00 Mbps optical d atalinks is dependent on th e following factor s: type of optical fiber, duplex mode of both end-n ...

  • IBM AT-FS202SC/FS1 - page 12

    Description 4 Key Features The AT-FS20x switches have the following features: ❑ LEDs for unit a nd port status ❑ Auto MDI/MDI-X ❑ DIP switches for configuring the ports ❑ Half- or full-duplex operation on both ports ❑ RJ-45 twisted-pair connector ❑ SC or ST fiber optic connector ❑ Data packet forwarding and filterin g at full wire spe ...

  • IBM AT-FS202SC/FS1 - page 13

    AT-FS20x Series Installation Guide 5 Twisted-Pair Port The AT-FS20x and AT-FS202SC/FSx Se ries switches have one 10Base-T/ 100Base-TX twisted-pair port. The twis ted-pair port features an RJ-45 connector. Port Speed The twisted-pair port is compliant with the 10Base-T and 10Base-TX standards and is capable of either 10 Mb ps or 100 Mbps operation. ...

  • IBM AT-FS202SC/FS1 - page 14

    Description 6 The twisted-pair port on the switch can operated in either half- o r full-duplex mode. You can set the duplex mode manu ally or allow the switch to set it automatically through Auto-Negotiation . With Auto-Negotia tion, if the end- node is capable of full-duplex mode, the twisted-pair port is set automatically to full-duplex mode. If ...

  • IBM AT-FS202SC/FS1 - page 15

    AT-FS20x Series Installation Guide 7 Switch Performance The AT-FS20x switches have th e following performance values: ❑ 148,800 pps for 100 Mbps and 14,880 pps for 10 Mbps for full wire speed forwarding and filtering ❑ 200 Mbps maximum throughput in 100 Mbps, full-duplex mode ❑ 20 Mbps maximum throughput in 10 Mbps, full-duplex mode ❑ Stora ...

  • IBM AT-FS202SC/FS1 - page 16

    Description 8 Store and Forward The AT-FS20x switches suppo rt store and forwa rd switching at Fa st Ethernet full-wire speed in 100 Mbps, half- or fu ll-duplex mode. Pack ets entering each port are stored in buffers. Once the pack et is re ceived, the switch forwards or discards the packet, depe nding on its destination address and error status. T ...

  • IBM AT-FS202SC/FS1 - page 17

    AT-FS20x Series Installation Guide 9 Figure 4 illustrates a topology using one AT -FS202 s witch to interconnect two small networks of stackable hubs. Figure 4 Typical Configuration Using the AT-FS202 Switch AT-8026C AT-FS202 AT-FS708 170 Twisted Pair Fiber Optic ...

  • IBM AT-FS202SC/FS1 - page 18

    Description 10 ...

  • IBM AT-FS202SC/FS1 - page 19

    11 Chapter 2 Installing the Switch This chapter explains how to inst all an AT-FS20x and AT-FS202S C/FSx Series switches. These sw itches can be installed on a des ktop or in an AT-MCR12 chassis. The procedures pr ovided in this chapter are for installation on a desktop. To in stall a switch in the AT-MCR12 chassi s, see the AT-MCR12 Chassis Instal ...

  • IBM AT-FS202SC/FS1 - page 20

    Installing the Switch 12 Planning the Installation Be sure to observe the foll owing guidelines when plan ning the installation of your switch. ❑ The end-node connected to the 100Ba se -FX fiber optic port must be able to operate at 100 Mbps. ❑ The end-node connected to the 10Base-T/100Base-TX twisted-pair port can operate at either 10 Mbps or ...

  • IBM AT-FS202SC/FS1 - page 21

    AT-FS20x Series Installation Guide 13 Note See “Fiber Optic Port Specifications” on page 22 for additional information on the fiber optic port. AT-FS202 50/125 or 62.5/ 125 micron multimode 2 km (1.2 mi) 13 dB at 1310 nm AT-FS202SC/FS1 50/125 or 62.5/ 125 multimode 2 km (1.2 mi) 13 dB at 1310 nm 9/125 micron single-mode 15 km (9.3 mi) 16 dB at ...

  • IBM AT-FS202SC/FS1 - page 22

    Installing the Switch 14 ❑ Refer to Table 5 for the cabling specificatio ns for the fiber optic port operating in half-duplex mode. Table 5 100Base-FX Fiber Optic Ports (Half-duplex) 1 1. The total distance o f the fiber optic lengths cannot exceed the limi ts stated in the table. E ach switch used inline within a single collision domain reduces ...

  • IBM AT-FS202SC/FS1 - page 23

    AT-FS20x Series Installation Guide 15 Installing the Switch This section provides a procedure for installing the AT-FS20x switches. When setting the DIP switches consider the following: ❑ Setting the Auto Neg DIP switch for the twisted-pair port to ON or OFF enables or disables auto-negotia tion for the port. If you disable auto-negotiation, be s ...

  • IBM AT-FS202SC/FS1 - page 24

    Installing the Switch 16 Caution After you change the speed or duplex mode of the switch, you must power cycle (shut down and restart) the sw itch for the new set tings to take affect. 4. Place the switch on a secure, level surface, leaving ample space around the switch for ventilation. 5. Plug the AC/DC power adapter into an appropriate AC power o ...

  • IBM AT-FS202SC/FS1 - page 25

    AT-FS20x Series Installation Guide 17 10. Connect the twisted-pair cabl e (or cables) to the end node. See Table 7 for information about setting the duplex mode. You must set the AT-FS20x switch and the end node to auto negotiate or make their port speeds match. Table 7 Setting the Duple x Mode 11. Power ON the end-nodes. 12. Verify that the LNK/AC ...

  • IBM AT-FS202SC/FS1 - page 26

    Installing the Switch 18 ...

  • IBM AT-FS202SC/FS1 - page 27

    19 Chapter 3 Troubleshooting Follow the guidelines bel ow to test and troubleshoot the in stallati on in the event a problem occurs. Note Whenever the speed and/or duplex mode are changed during or after power ON, power O FF then power back ON the switch to load the new configuration. If the PWR LED is OFF, do the following: ❑ If the switch is in ...

  • IBM AT-FS202SC/FS1 - page 28

    Troubleshooting 20 ❑ Make sure that the twisted-pair ca ble does not exceed 100 meters (328 feet) and that you are using a Catego ry 3 or better cable for 10Base-T operation or a Category 5 or better cable for 100Bas e-TX operation. For information about maximum operating distanc es, see Table 1 on page 3 . If the LNK/ACT LED for the fiber opti c ...

  • IBM AT-FS202SC/FS1 - page 29

    21 Appendix A Technical Specifications Physical Dimensions: W x D x H 10.5 cm x 9.5 cm x 2.5 cm (4.12 in x 3.75 in x 1.0 in) Weight: 294 g (10.4 oz) Temperature Maximum Operating: 0° C to 40° C (32° F to 104° F) Maximum Storage: -20° C to 80° C (-4° F to 176° F) Relative Humidity: 5% to 95% non-condensing Operating Altitude: Up to 3, 048 me ...

  • IBM AT-FS202SC/FS1 - page 30

    Technical Specifications 22 Agency Certifications Safety Conforms to all standards normally supported by Allied Telesyn prod ucts including safety standards UL 1950, CSA 22.2 No. 950, TUV EN60950, EN60825 CE Compliant Standard CE Compliant IEEE 80 2.3, IEEE 802.3u Immunity Conforms to EN55024 immunity standard EMI/RFI Meets all applicable re quirem ...

  • IBM AT-FS202SC/FS1 - page 31

    AT-FS20x Series Installation Guide 23 Table 9 Fiber Optic Receiver Table 10 Fiber Optic Datalink Model Fiber Type 1 1. MMF = Multimode Fiber / SMF = Single-mode Fiber. Fiber Optic Diameter (microns ) Optical Wavelength Receiver Sensitivity (dBm) Min. Avg. Saturation AT-FS201 & AT-FS202 MMF 50/125 1310 nm -31.8 -34.5 -14.5 MMF 62.5/125 1310 nm - ...

  • IBM AT-FS202SC/FS1 - page 32

    Technical Specifications 24 Table 11 Fiber Optic Loss Specification (Bench mark) Pinout Assignments Figure 5 shows the pin assignment s of the RJ-45 connector. Figure 5 RJ-45 Pin Assignments AT-FS202SC/ FS3 9/125 SMF 33.00 dB 35.00 dB 15 km (9.4 mi) 75 km (46 mi) AT-FS202SC/ FS4 9/125 SMF 34.0 35.5 dB 40 km (24.8 mi) 100 km (62 mi) 1. MMF = Multimo ...

  • IBM AT-FS202SC/FS1 - page 33

    AT-FS20x Series Installation Guide 25 Table 12 lists the 10Ba se-T/100Base-TX co nnector pins and their signals when the port is oper ating in either MDI or MDI-X configura tion. Table 12 RJ-45 Pinouts MDI-X (Default) Signal MDI Signal 1 RX+ 1 TX+ 2 RX- 2 TX- 3 TX+ 3 RX+ 4 - 4 - 5 - 5 - 6 TX- 6 RX- 7 - 7 - 8 - 8 - ...

  • IBM AT-FS202SC/FS1 - page 34

    Technical Specifications 26 ...

  • IBM AT-FS202SC/FS1 - page 35

    27 Appendix B Translated Safety and Emission Information Important : This appendix contains multip le-language translations for t he safety statements in this guide. Wichtig : Dieser Anhang enth ält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinwe ise in mehreren Sprachen. Vigtigt : Dette tillæg indeholder oversættelser i flere ...

  • IBM AT-FS202SC/FS1 - page 36

    Translated Safety and Emission Information 28 Standards : This product meets the f ollowing standards.  1R F I E m i s s i o n EN55022 Class A  2 Warning : In a domestic environment this prod uct may cause radio interference in which case the u ser may be required to take ad equate measures.  3 Immunity EN55024  4 Warning : This product ...

  • IBM AT-FS202SC/FS1 - page 37

    AT-FS20x Series Installation Guide 29 USA/Canada Use a UL Listed/CSA Certifie d AC adapter of DC 12V, 500mA. Europe - EU Use TÜV licensed AC adapter of DC 12V, 500mA. UK Use a UK Safety Approved AC ad apter of DC 12V, minimum 500mA .  13 Operatin g Temperatur e: This produc t is designed for a ma ximum ambient temperature of 40 degrees C.  1 ...

  • IBM AT-FS202SC/FS1 - page 38

    Translated Safety and Emission Information 30 Standarder : Dette produkt tilfredsstille r de følgende standarder.  1R a d i o f r e k v e n s forstyrrelsesemission EN55022 Klasse A  2 Advarsel : I et hjemligt miljø kunne dette prod ukt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brug eren muligvis at tage tilstrækkelig ...

  • IBM AT-FS202SC/FS1 - page 39

    AT-FS20x Series Installation Guide 31  7 Waarshuwing K lasse-1 laser p rodukt.  8 Waarchuwing Neit in de straal staren.  9 Dit is een “Klasse 1 LED-produkt” Veiligheid  10 Gevaar Voor Blikseminslag Gevaar : Niet aan t oestellen of kabels werken bij blikse m.  11 Ventilatiegaten niet blokkere n.  12 Stroom mag alleen via de ada ...

  • IBM AT-FS202SC/FS1 - page 40

    Translated Safety and Emission Information 32  13 Température De Fonc tionnement Ce matériel est capable de tolérer une tempéra ture ambiante maximum de 40 degrés Celsius.  14 Pour Tous Pays : Installer le matériel confor mément aux normes électriques nationales et locales. Standardit : Tämä tuote on seuraav ien standardien mukainen ...

  • IBM AT-FS202SC/FS1 - page 41

    AT-FS20x Series Installation Guide 33 Standard : Questo prodotto è confor me ai seguenti standard.  1 Emissione RFI (inte rferenza di radiofrequenza) EN55022 Classe A  2 Avvertenza : in ambiente domes tico questo prodotto p otrebbe causare radio interferenza. In questo caso potrebbe richiedersi all'uten te di prendere gli adeguati provv ...

  • IBM AT-FS202SC/FS1 - page 42

    Translated Safety and Emission Information 34  6 Laser EN60825  7A d v a r s e l Laserprodukt av klasse 1.  8A d v a r s a l Stirr ikke på strålen.  9 Dette er et “Klasse 1 LED produkt” Sikkerhet  10 Fare Fo r Lynne dslag Fare : Arbeid ikke på utstyr eller kabler i tordenvær.  11 Blokker Ikke Luftventilene  12 All strø ...

  • IBM AT-FS202SC/FS1 - page 43

    AT-FS20x Series Installation Guide 35  13 Temperatura De Funcionamento Este produto foi p rojetado para uma temperatura ambiente máxima de 4 0 graus centígrados.  14 Todos Os Países : Inst ale o produto de acordo com as no rmas nacionais e locais para instalações elétricas. Estándares : Este producto cumple c o n los siguiente s están ...

  • IBM AT-FS202SC/FS1 - page 44

    Translated Safety and Emission Information 36  5E l s ä k e r h e t TUV-EN60950, UL1950, C SA 950  6 Laser EN60825  7 Varning! Laserprodukt av klass 1.  8 Varning! Laserstr ålning när enheten är öppe n.  9 Detta är en “Klass 1 lysdiodprodukt” Säkerhet  10 Fara Fö r Blixtne dslag Fara : Arbeta ej på utrustningen eller ...

Manufacturer IBM Category Switch

Documents that we receive from a manufacturer of a IBM AT-FS202SC/FS1 can be divided into several groups. They are, among others:
- IBM technical drawings
- AT-FS202SC/FS1 manuals
- IBM product data sheets
- information booklets
- or energy labels IBM AT-FS202SC/FS1
All of them are important, but the most important information from the point of view of use of the device are in the user manual IBM AT-FS202SC/FS1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals IBM AT-FS202SC/FS1, service manual, brief instructions and user manuals IBM AT-FS202SC/FS1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product IBM AT-FS202SC/FS1.

Similar manuals

A complete manual for the device IBM AT-FS202SC/FS1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use IBM AT-FS202SC/FS1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of IBM AT-FS202SC/FS1.

A complete IBM manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual IBM AT-FS202SC/FS1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the IBM AT-FS202SC/FS1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the IBM AT-FS202SC/FS1, that we can find in the current document
3. Tips how to use the basic functions of the device IBM AT-FS202SC/FS1 - which should help us in our first steps of using IBM AT-FS202SC/FS1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with IBM AT-FS202SC/FS1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of IBM AT-FS202SC/FS1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning IBM AT-FS202SC/FS1?

Use the form below

If you did not solve your problem by using a manual IBM AT-FS202SC/FS1, ask a question using the form below. If a user had a similar problem with IBM AT-FS202SC/FS1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)