English dropdown-ico

Manual Cisco Systems 7513

24 pages 1.23 mb
Download

Go to site of 24

Summary
  • Cisco Systems 7513 - page 1

    Corporate Headquarters: Copyright © 20 04 Cisco Systems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 This document contains instructions for upgrading your existing Cisco 7513, 1200-watt (W), alternating current (A C)–input po ...

  • Cisco Systems 7513 - page 2

    2 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Determining the Power Supply Model • Obtaining T echnical Assistance, page 21 • Obtaining Additional Publications and Information, page 22 Determining the Power Supply Model The Cisco 7513, A C-input po wer supplies carry one of the following part numbers: • The o ...

  • Cisco Systems 7513 - page 3

    3 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview Product Overview The A C-input power supply is optional equipment in the Cisco 7513. Po wer supplies reside in po wer supply bays in the rear of the router chassis. shows the Cisco 7513 with the older po wer supplies installed (Part Number 34-0049-01 or ...

  • Cisco Systems 7513 - page 4

    4 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview Figur e 3 Cisco 7513 (Rear -P anel V iew with the New Po wer Supplies) Caution T o pre vent problems with the Cisco 7513, do not mix DC-input and A C-input power supplies in the same chassis . Y our Cisco 7513 must hav e either DC-input or AC-input po w ...

  • Cisco Systems 7513 - page 5

    5 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview Power Supply Specifications T able 1 lists the AC-input po wer supply specif ications. The specif ications listed in T able 1 apply to the new and older A C-input power supplie Dual po wer supplies are automatically load-sharing and redundant, which mea ...

  • Cisco Systems 7513 - page 6

    6 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview Figur e 4 20-Amp A C P ower Cable Connector and Plug, and 20-Amp Receptac le Power Supply LED Indications On the Cisco 7513 chassis front panel, the power A and po wer B LEDs go on when the po wer supply in the corresponding bay is installed and supplyi ...

  • Cisco Systems 7513 - page 7

    7 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview In systems with a single power supply , and in systems with redundant po wer when both power supplies are shutting do wn, the output fail LED lights momentarily as the system ramps down, b ut goes out when the power supply has completely shut do wn. The ...

  • Cisco Systems 7513 - page 8

    8 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview • A spring clip on the A C receptacle supplies strain relief and pre vents the po wer supply power cable from being pulled out accidentally . Environmental Monitoring and Reporting Functions The en vironmental monitoring and reporting functions, contr ...

  • Cisco Systems 7513 - page 9

    9 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview • Power supply shutdo wn—An out-of-tolerance v oltage, current, or temperature condition was detected within the power supply and it w as shut down (or a shutdo wn is imminent). All DC po wer remains disabled until the operator toggles the po wer sw ...

  • Cisco Systems 7513 - page 10

    10 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview Environmental Reports The system displays warning messages on the console if chassis interface-monitored parameters exceed a desired threshold or if a blower f ailure occurs. Y ou can also retrie ve and display en vironmental status reports with the sh ...

  • Cisco Systems 7513 - page 11

    11 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Product Overview The show en vir onment table command displays the temperature and voltage thresholds for each of the three RSP2 temperature sensors, for each monitored status lev el: low critical, lo w warning, high warning, and high critical, which are the same as th ...

  • Cisco Systems 7513 - page 12

    12 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Installation Safety, ESD Precautions, and Tools Required Power supply #1 is 1200W AC (id 1), power supply #2 is removed (id 7) Active fault conditions: Blower #3 Fan speed is 50% Active trip points: none 15 of 15 soft shutdowns remaining before hard shutdown 1 01234567 ...

  • Cisco Systems 7513 - page 13

    13 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Installation Safety, ESD Precautions, and Tools Required • Before beginning an y procedures requiring access to the chassis interior , locate the emergency power -of f switch for the room in which you are working. • Disconnect all po wer and external cables before ...

  • Cisco Systems 7513 - page 14

    14 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Replacing Older AC-Input Power Supplies • If access to the po wer supply bays is partially blocked by a power strip or other permanent rack f ixture, you will need a 1/4-inch f lat-blade screwdri ver to temporarily detach the ears from the equipment rack mounting str ...

  • Cisco Systems 7513 - page 15

    15 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Removing Older Power Supplies Removing Older Power Supplies Follo w these steps to remov e an older power supply (P art Number 34-0049-01 or later): Step 1 T urn OFF (O) the system po wer switch on the power supply you plan to remo ve. Step 2 If possible, turn OFF the ...

  • Cisco Systems 7513 - page 16

    16 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Removing Older Power Supplies Figur e 9 Supporting the Older P o wer Supply Step 6 If you hav e a second power supply , repeat steps 1 through 5 to remov e it. Caution T o maintain agency compliance requirements and meet EMI emissions standards in a Cisco 7513 chassis ...

  • Cisco Systems 7513 - page 17

    17 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Removing Older Power Supplies Figur e 1 1 Supporting the New P o wer Suppl Step 2 Use the large slotted scre wdri ver to tighten the capti ve scre w that secures the power supply to the chassis frame. (See .) Figur e 12 Location of Captive Installation Scr ews on the N ...

  • Cisco Systems 7513 - page 18

    18 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Checking the New Power Supply Installation Checking the New Power Supply Installation T o complete the installation, turn each po wer supply on and observe its LEDs to verify that it is operating properly . Step 1 Revie w the descriptions of the po wer supply LEDs on p ...

  • Cisco Systems 7513 - page 19

    19 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Checking the New Power Supply Installation This completes the power supply upgrade. Refer to the Cisco 7513 Hardwar e Installation and Maintenance publication for installation troubleshooting procedures, and to the appropriate software conf iguration publication for de ...

  • Cisco Systems 7513 - page 20

    20 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Related Documentation Related Documentation See the follo wing for a listing of additional documentation for the Cisco 7500 Series routers: • Cisco 7500 Series Documentation Roadmap • Cisco 7500 Series Routers P ort Adapter Documentation Roadmap • Cisco 7500 Seri ...

  • Cisco Systems 7513 - page 21

    21 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Documentation Feedback Y ou can order Cisco documentation in these ways: • Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www .cisco.com/en/US/partner/ordering/index.shtml • Nonregistered Cis ...

  • Cisco Systems 7513 - page 22

    22 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Obtaining Additional Publications and Information provides recommended solutions. If your issue is not resolv ed using the recommended resources, your service request will be assigned to a Cisco T A C engineer . The T A C Service Request T ool is located at this URL: h ...

  • Cisco Systems 7513 - page 23

    23 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Obtaining Additional Publications and Information • Cisco Pr ess publishes a wide range of general networking, training and certif ication titles. Both new and experienced users will benef it from these publications. For current Cisco Press titles and other informati ...

  • Cisco Systems 7513 - page 24

    24 Upgrading the 1200-Watt, AC-Input Power Supplies in the Cisco 7513 OL-6324-01 Obtaining Additional Publications and Information ...

Manufacturer Cisco Systems Category Network Router

Documents that we receive from a manufacturer of a Cisco Systems 7513 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 7513 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 7513
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 7513.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 7513, service manual, brief instructions and user manuals Cisco Systems 7513. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 7513.

Similar manuals

A complete manual for the device Cisco Systems 7513, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 7513 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 7513.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 7513 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 7513, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 7513, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 7513 - which should help us in our first steps of using Cisco Systems 7513
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 7513
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 7513 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 7513?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 7513, ask a question using the form below. If a user had a similar problem with Cisco Systems 7513 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)