English dropdown-ico

Manual Lucent Technologies 7820-0802-003

242 pages 2.2 mb
Download

Go to site of 242

Summary
  • Lucent Technologies 7820-0802-003 - page 1

    APX 8000 ™ /MAX ® TNT/DSLMAX ™ Physical Inte rface Con fi guration Guid e Part Numbe r 7820- 0802 -003 For softwar e versi on 8.0 May 2 000 ...

  • Lucent Technologies 7820-0802-003 - page 2

    Lucent Tec hnologi es Copyright© 2000 Lu cent T echnologies. All rights reserved. This ma terial is protect ed by the c opyright laws of the U nited States and o ther countr ies. It may n ot be rep roduce d, distribu ted, or alte red in any fashion by any entit y (eith er i ntern al or ex terna l to Luce nt T ec hnolog ies), except in acc ordan ce ...

  • Lucent Technologies 7820-0802-003 - page 3

    85x11 B ook Temp late (Pr eliminary) iii Customer Service Customer Service provides a variety of op tions for obtaining in formation about L ucent products and s ervices, softwar e upgrades, and tech nical assistance. Finding information and softw are on the Int ernet V isit the W eb site at http://www.lucent.com/ins for technical inform ation, pro ...

  • Lucent Technologies 7820-0802-003 - page 4

    iv 85x11 Book Template (Prelimin ary) support s ervices p rovide har dware and s oftware so lutions to keep y our networ k operati ng at peak perfor mance. For mo re information, call (8 00) 27 2-3634. Othe r telep hone numb ers For a menu of Lucent ’ s services, call (8 00) 27 2-3634. Or call (5 10) 769-6 001 for an operator . Calling Luce nt fr ...

  • Lucent Technologies 7820-0802-003 - page 5

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide v Content s Customer Service .......................... ............ ........... ........... ................. ........... ............ ........... ...... iii About This Guide ................ ......... .............. .......... ......... ......... ......... xvii What is in this guid e ...

  • Lucent Technologies 7820-0802-003 - page 6

    vi APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Contents Configurin g the APX 8000 for shelf-co ntroller redundan cy ................. ........... ........... .......... 2- 3 Assigning the system IP address ......................... ........... ........... ........... ................. .......... 2-4 Assigning an Ethernet IP add ...

  • Lucent Technologies 7820-0802-003 - page 7

    Contents APX 8000/MAX TNT/DSLTNT Physical Interface Configur ation Guide vii Chapter 6 Configuring MultiDSP Cards (MAX TNT , AP X 8 000) .......... ......... .......... ......... .............. ......... ......... 6 -1 Introduction to MultiDSP.............. ...... ...... ........... ...... ........... ...... ........... ..... ............ ..... ... ...

  • Lucent Technologies 7820-0802-003 - page 8

    viii APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Contents Specifying analog encoding f or TAOS unit codecs .................... ........... ................. ........... .. 7-22 Configurin g specialized options.......... ........... ................. ............ ........... ........... ................. .. 7-22 Sample T1 config ...

  • Lucent Technologies 7820-0802-003 - page 9

    Contents APX 8000/MAX TNT/DSLTNT Physical Interface Configur ation Guide ix Routing pr otocols .............. ........... ................. ........... ............ ........... ........... ................. .. 10-2 RADIUS................ ................. ............ ........... ........... ............ ................ ............ ........... .. ...

  • Lucent Technologies 7820-0802-003 - page 10

    x APX 8000/MAX TNT/DSLTNT P hysic al Interface Configuration Guide Contents Chapter 15 Configuring OC3-A TM Cards (MAX TNT/DSL TNT) .................. ......... ......... .......... .............. ......... .. 15-1 Introduction to OC3-ATM ............ ...... ........... ............ ..... ............ ..... ........... ............ ..... ........ 1 ...

  • Lucent Technologies 7820-0802-003 - page 11

    Contents APX 8000/MAX TNT/DSLTNT Physical Interface Configur ation Guide xi Sample Frame Relay IDSL con figuration ..................... ........... ........... ................. ...... 17-22 Configurin g the DSLTNT ..................... ........... ............ ........... ................. ........... 17-23 Configurin g the Pipeline ............. ...

  • Lucent Technologies 7820-0802-003 - page 12

    xii APX 8000/MAX TNT/DSLTNT P hysic al Interface Configuration Guide Contents Start and Stop record s ................. ........... ................. ........... ........... ................. ...... 18-21 Disconnect cause codes ........ ...... ..... ............ ..... ............ ........... ..... ............ ..... ...... 18-21 SNMP support for S ...

  • Lucent Technologies 7820-0802-003 - page 13

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide x iii Figures Figure 13-1 Example of un channelized DS3 slot card application ............ ............ ........... .. 13-1 Figure 14-1 DS3-ATM interface to ATM network .............. ........... ........... ............ ............. 14-1 Figure 15-1 OC3-ATM interface to ATM network.. ...

  • Lucent Technologies 7820-0802-003 - page 14

    ...

  • Lucent Technologies 7820-0802-003 - page 15

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide xv Ta b l e s Table 1-1 Basic TAOS unit config uration tasks ..................... ................ ............ ........... .... 1-2 Table 5-1 Modem configu ration tasks ................... ........... ........... ................. ........... .......... 5-2 Table 7-1 T1 line configu ...

  • Lucent Technologies 7820-0802-003 - page 16

    ...

  • Lucent Technologies 7820-0802-003 - page 17

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide xvii About T his Guide What is in t his guide This guide provides the following instr uct ions fo r an APX 8000 ™ , MAX T NT ® , or DSL T NT ™ multiservice access con centrator: • Basi c conf i gurat ion of your u nit • Config uring shel f contro ller redundan cy (A PX 8000 on ...

  • Lucent Technologies 7820-0802-003 - page 18

    xviii APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Documenta tion conv entions • Network security Documentation conventions Following are all the special characters and typogr aphical conventio ns used in this manual: Conv ent ion Mean in g Monospace text Represents text that appears on your com puter ’ s screen, or that coul ...

  • Lucent Technologies 7820-0802-003 - page 19

    Documentat ion se t APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide xix Documentation set The APX 8000/MAX TNT/D SL TNT docum entation set consists of the following manual s. • Read me first: – Access Networks Safety a nd Co mpliance Guide Contains important safety instructions and cou ntry-specific compliance inform ation that ...

  • Lucent Technologies 7820-0802-003 - page 20

    xx APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Documenta tion set • RADIUS: T AOS RADIUS Guide and Refer ence Describes how to set up a T A OS unit to use the Remote Authenticatio n Dial -In User Service (RADIUS) server and contains a complete r eference to RADIUS attributes. • Administra t ion and troublesho oting: APX 800 ...

  • Lucent Technologies 7820-0802-003 - page 21

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 1- 1 1 Performing Basic Configura tion Introduction to basic co nfiguratio n T abl e 1 - 1 lists the sections describ ing the tasks you must perf orm for the T AOS unit basic configuration. The table includes a b rief description of each task and lists the com ...

  • Lucent Technologies 7820-0802-003 - page 22

    1-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Introduc tion to bas ic config uration T able 1- 1. Basic T AOS unit confi guration tasks Section Des c ri pt i o n of tas k Related commands or parameters “ Connecting t o a new u nit ” on page 1- 3 Connect the T AOS uni ...

  • Lucent Technologies 7820-0802-003 - page 23

    Performing Ba sic Configuration Connecti ng to a new unit APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 3 Connecting to a new unit T o communicate with a new T A OS unit, you mu st assign an IP addres s to the shelf controller . Once this is done, you can perfo rm further configur ation over a LAN usin g ...

  • Lucent Technologies 7820-0802-003 - page 24

    1-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Configu ring the shelf-con troller IP addres s on a nonr edundant unit 4 V erify that the connection and the IP addres s are correct by pinging any d evice on the netw ork. admin> ping 10.10.10.1 64 bytes from 10.10.10.1: ...

  • Lucent Technologies 7820-0802-003 - page 25

    Performing Ba sic Configuration Settin g the system date APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 5 Setting the system date If the system date displayed on your screen is incor rect, set the correct da te and time with the Date command . For exampl e, to set the date and t ime to Oct ober 22, 2000, ...

  • Lucent Technologies 7820-0802-003 - page 26

    1-6 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Conf ig uri ng a de fa ult gat eway T o change the log lev el, specify an optio n for the Save-Level parameter: admin> set save-level = [ none | emergency | alert | criti- cal | error | warning | notice | info | debug ] ad ...

  • Lucent Technologies 7820-0802-003 - page 27

    Performing Ba sic Configuration Pinging the TAO S unit from a local host APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 7 domain-name = "" dns-primary-server = 0.0.0.0 dns-secondary-server = 0.0.0.0 netbios-primary-ns = 0.0.0.0 netbios-secondary-ns = 0.0.0.0 must-accept-address-assign = no pool- ...

  • Lucent Technologies 7820-0802-003 - page 28

    1-8 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Recommen ded basic security m easures Changing the Ad min p assword A user who k nows the passwor d to the Admin level can p erform any o peration on the T AOS unit, i ncluding chan ging th e configurat ion. The Ad min pass w ...

  • Lucent Technologies 7820-0802-003 - page 29

    Performing Ba sic Configuration Recommen ded basic security m easures APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 9 Following is an example of assigning a T elnet password: admin> read ip-global IP-GLOBAL read admin> set telnet-password = SDwiw87 admin> write IP-GLOBAL written All users attemp ...

  • Lucent Technologies 7820-0802-003 - page 30

    1-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Recommen ded basic security m easures T o prevent the T AOS unit router from being used as an intermediary in this type of denial-of -ser vice attack laun ched from another network, you must dis able the T AO S unit from forw ...

  • Lucent Technologies 7820-0802-003 - page 31

    Performing Ba sic Configuration Recommen ded basic security m easures APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 1-1 1 Following are the paramete rs related to SNMP security: SNMP enabled = no read-community = public read-write-community = write enforce-address-security = no read-access-hosts = [ 0.0.0. ...

  • Lucent Technologies 7820-0802-003 - page 32

    1-12 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Where to go next In the following example, commands enforce address securi ty and specify a trusted address for read and write access: admin> read snmp SNMP read admin> list enabled = no read-community = public read-wri ...

  • Lucent Technologies 7820-0802-003 - page 33

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2-1 2 Configu ring Sh elf-Contr oller Redundanc y (APX 8000 ) Over view of redu ndan cy op eratio ns The APX 8000 can oper ate with a single shelf contro ller or with two red undant shelf controllers. When the APX 8000 runs with two shelf controller s, one contr ...

  • Lucent Technologies 7820-0802-003 - page 34

    2-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Overvie w of redun dancy op erations The controllers next elect the controller that will be primary. The election process is based on a hierarchical list of co mplex criteria. The firs t criterion in the lis ...

  • Lucent Technologies 7820-0802-003 - page 35

    Configuring Shelf-Controller Redundanc y (APX 8000) Config uring the APX 8000 fo r shelf-c ontroll er redundan cy APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 3 Controller switchover If the primary controller fatals, the seco ndar y contro ller autom a tically takes over as primary controller . The new ...

  • Lucent Technologies 7820-0802-003 - page 36

    2-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Configu ring the AP X 8000 for shelf-c ontroller redundancy Assigning the system IP address T o configure an A PX 8000 t hat has redu ndant s helf control lers, y ou must map system I P settings to th e unit ...

  • Lucent Technologies 7820-0802-003 - page 37

    Configuring Shelf-Controller Redundanc y (APX 8000) Config uring the APX 8000 fo r shelf-c ontroll er redundan cy APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 5 admin> set ip-address = 192.168.100.2/24 admin> write IP-INTERFACE/{ { shelf-1 right-control ler 1 } 0 } written After you assign IP addr ...

  • Lucent Technologies 7820-0802-003 - page 38

    2-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Configu ring the AP X 8000 for shelf-c ontroller redundancy Configuring shelf-contro ller redundancy When setting up shelf-controller red undancy , you might need to configure the followin g profiles: • Ph ...

  • Lucent Technologies 7820-0802-003 - page 39

    Configuring Shelf-Controller Redundanc y (APX 8000) Config uring the APX 8000 fo r shelf-c ontroll er redundan cy APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 7 admin> read redundancy REDUNDANCY read admin> list [in REDUNDANCY] context = [ { } { } ] primary-preference = no-preference The following ...

  • Lucent Technologies 7820-0802-003 - page 40

    2-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Configu ring the AP X 8000 for shelf-c ontroller redundancy Switchin g the primary controller at the command-line interf ace Y ou can manuall y sw itch primary shelf-controller functio n a lity to the second ...

  • Lucent Technologies 7820-0802-003 - page 41

    Configuring Shelf-Controller Redundanc y (APX 8000) Obtaini ng status informa tion about redundant shelf control lers APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 9 the default security level is reactiv ated . In addition, a system reset can cause a W AN lin e to temporarily be shut down due to momentar ...

  • Lucent Technologies 7820-0802-003 - page 42

    2-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Obtaini ng status informat ion about r edundant shelf controller s disrupted and then reestablis hed, the uptime command rep orts the time elapsed since the secondary contr oller reestablished commun icati ...

  • Lucent Technologies 7820-0802-003 - page 43

    Configuring Shelf-Controller Redundanc y (APX 8000) Obtaini ng status informa tion about redundant shelf control lers APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 2-1 1 The following example di splays the show comman d entered on the s econdary con troller when the right contro ller is primary: admin> ...

  • Lucent Technologies 7820-0802-003 - page 44

    ...

  • Lucent Technologies 7820-0802-003 - page 45

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 3- 1 3 Configur in g the Therma l Profile for Fa n T ray Operat ions (APX 80 00) Overview of the Thermal p rofile for fan tray operation s On the APX 8000, an on-board d igital temperature chip on the shelf contro ller and a temperature device at th e intake e ...

  • Lucent Technologies 7820-0802-003 - page 46

    3-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring the Thermal Pr ofile for Fan Tray Operations (APX 8000) Overvie w of the Th ermal prof ile for fan t ray operat ions Example of configur ing thermal controls The command s in the follow ing example sh ow how to co nfigure the fan tray to run th ...

  • Lucent Technologies 7820-0802-003 - page 47

    Configuring the Thermal Profile for Fan Tray Operations (APX 8000) Overv iew of the The rmal profi le for fan tr ay operati ons APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 3- 3 admin> write THERMAL written admin> list [in THERMAL] fantray-lownoise-rpm = 2500 operation-mode = auto-regulation low-temp ...

  • Lucent Technologies 7820-0802-003 - page 48

    3-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring the Thermal Pr ofile for Fan Tray Operations (APX 8000) Thermal s tatus re porting Thermal status reporting A power -on self test ( POST) is ru n on the f an tray of the APX 800 0 during the BOOT l oader and during the operational load. If the ...

  • Lucent Technologies 7820-0802-003 - page 49

    Configuring the Thermal Profile for Fan Tray Operations (APX 8000) Thermal status re portin g APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 3- 5 Thermalst atus command The thermalstatus comman d displays a number of temperature-r elated values to sh ow the over all thermal s tatus of the unit. For exam ple, ...

  • Lucent Technologies 7820-0802-003 - page 50

    ...

  • Lucent Technologies 7820-0802-003 - page 51

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 4- 1 4 Configu ring Et hernet Ca rds Introduction to Ethernet slot cards This chapter explains how to install and co nfigure the Ethern et slot cards. For information about confi guring IP routing, see the APX 8 000/MAX TNT DSL TNT W AN, Routing and T unneling ...

  • Lucent Technologies 7820-0802-003 - page 52

    4-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Ethernet Cards Overvie w of Ether net co nfi gurati on Upgrading to the Ethernet-2 and Et hernet-3 slot cards T o upgrade from an existing 10Mbps or 10/100Mb ps Ethern et card to an Ethernet- 2 or Ethernet-3 slot card, proceed as in the followi ...

  • Lucent Technologies 7820-0802-003 - page 53

    Configuring Ethernet Cards Config uring duple x mode on the 100 Mbps Ethe rnet port APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 4- 3 5 08/06/1998 17:11:46 { shelf-2 slot-4 3 } 5 08/06/1998 17:11:46 { shelf-2 slot-4 4 } If the 1 0/100 Mbps Ethernet-2 card is instal led, t he 100Mbps Ethernet port is d ispl ...

  • Lucent Technologies 7820-0802-003 - page 54

    ...

  • Lucent Technologies 7820-0802-003 - page 55

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 5- 1 5 Confi g u ring Series5 6 II an d III Modem and Hybrid Access Card s T ypically , Series56 II ™ and Se r ies 56 III Di gital M odem sl ot car ds do n ot requ ire a ny configurat ion. Dependin g on your net work, si tuation s might requ ire you to chang ...

  • Lucent Technologies 7820-0802-003 - page 56

    5-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Series56 II and III Modem and Hybrid Access Cards Specify ing modem negotiati on settin gs Specifying mod em negoti ation setti ngs Calls from analo g modems are d ir ected f irst to th e dig ital mod ems, where the conn ection mus t be negotia ...

  • Lucent Technologies 7820-0802-003 - page 57

    Configuring Series56 II and III Modem and Hy brid Access Card s Speci fying modem modulatio n for Seri es56 II and III modem c ards APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 5- 3 2 List the parameters in the Modem-Conf ig uration subprofile. For example: admin> list modem-configuration v42/mnp = will ...

  • Lucent Technologies 7820-0802-003 - page 58

    5-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Series56 II and III Modem and Hybrid Access Cards Series56 II and III Call-Rou te profil es rate and the A T -Answer-S tring par ameter specifies a dif ferent baud rate, the answer string overwrites the configured maxim um b aud rate. Following ...

  • Lucent Technologies 7820-0802-003 - page 59

    Configuring Series56 II and III Modem and Hy brid Access Card s Prevent ing Seri es56 II an d III ca rds from d elayi ng Frame R elay c onnections APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 5- 5 Preventing Series56 II and III cards from delaying Frame R elay connections If the APX 8000 o r MAX TNT has a ...

  • Lucent Technologies 7820-0802-003 - page 60

    ...

  • Lucent Technologies 7820-0802-003 - page 61

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6-1 6 Configuring Mult iDSP Cards (MAX TNT , APX 8000) Introduction to MultiDSP The MultiDSP card is a highly versatile, digital signal processor (DSP ) slot card for MAX TNT and APX 8000 units. The following services are s upported by the MultiDSP card: • Dat ...

  • Lucent Technologies 7820-0802-003 - page 62

    6-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Introduc tion to Mul tiDSP 48-port MultiDSP card The 48-port MultiDSP card supports up to 48 ports of servi ce. Note: In MAX TNT and APX 8000 profiles and parameters, the 48-port MultiDSP card is identified as ma ...

  • Lucent Technologies 7820-0802-003 - page 63

    Configuring MultiDSP Cards (MAX TNT, APX 8000) Suppo rted Mult iDSP ser vices APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 3 Card configuration constraints The following constr aints affect th e mixing of slo t cards in MAX TNT and APX 8000 units . Using 48-port and 96 -port Multi DSP car ds Y ou cannot ...

  • Lucent Technologies 7820-0802-003 - page 64

    6-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Suppo rted Mult iDSP s ervic es V .110 features supported by the MultiDSP card include the following: • Asynchronous, answer-mode only (answer , but no call out), with 1 start bit, 8 data bits, and 1 st op bit ...

  • Lucent Technologies 7820-0802-003 - page 65

    Configuring MultiDSP Cards (MAX TNT, APX 8000) Obtainin g status information about a MultiDSP card APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 5 A V oI P so ft ware li cense is required for MultiDS P support of the V oIP service. An additional software license is required fo r supp ort of real-time fax ...

  • Lucent Technologies 7820-0802-003 - page 66

    6-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Configu ring a M ultiD SP card For example, enter the following comman d to di sp lay inf orm atio n about a 96-port MultiDSP card (identified as madd2-car d ) installed in shelf 1, slot 10 of a MAX TNT unit: adm ...

  • Lucent Technologies 7820-0802-003 - page 67

    Configuring MultiDSP Cards (MAX TNT, APX 8000) Configur ing a Mul tiDSP c ard APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 7 • V erifying that all other con figurations associated with the Mu ltiDSP services have been performed. For example, for V oI P MultiDSP support, all required configu rations fo ...

  • Lucent Technologies 7820-0802-003 - page 68

    6-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Configu ring a M ultiD SP card ... phs-support = yes ... voip-enabled = no ... v110-enabled = disabled ... rtfax-enabled = no ... V erifying call routes for Mul ti DSP service s Y ou can verify call routes for en ...

  • Lucent Technologies 7820-0802-003 - page 69

    Configuring MultiDSP Cards (MAX TNT, APX 8000) Configur ing a Mul tiDSP c ard APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 9 The following example shows a Call -Route profile for the V oIP service ( entry is 3) on a 48-port MultiDSP card in stalled in slot 5: 33 12/10/1999 18:25:32 {{{shelf-1 slot-5 0} ...

  • Lucent Technologies 7820-0802-003 - page 70

    6-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Configu ring a M ultiD SP card Viewing call -routing d ataba s e entri es Unlike the Call Route profiles, entries in a call-routing database are created f or the analog modem service, dig ital service, and for ...

  • Lucent Technologies 7820-0802-003 - page 71

    Configuring MultiDSP Cards (MAX TNT, APX 8000) Configur ing a Mul tiDSP c ard APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 6-1 1 admin> slot -r 1 5 admin> slot -u When the MultiDSP cards are brought u p, the unit cr eates n ew profiles and call route entries for each service, including the new serv ...

  • Lucent Technologies 7820-0802-003 - page 72

    ...

  • Lucent Technologies 7820-0802-003 - page 73

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 7- 1 7 Configur in g T1 Cards Introduction to T1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7- 2 Overview of T1 co nfiguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Lucent Technologies 7820-0802-003 - page 74

    7-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Introductio n to T1 Introduction to T1 A T1 line consists of 24 channels. Each channel can transmit and receive data or digitized voice. The l ine uses fram ing and signal ing to ach ieve synchron ous and rel iable trans mission. The m ...

  • Lucent Technologies 7820-0802-003 - page 75

    Configuring T1 Ca rds Overvi ew of T1 conf iguratio n APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 3 Overview of T1 conf iguration T able 7-1 lists t he secti on s des cri bi ng com mon t ask s you mi g ht hav e to perform t o co nfi g ure a T1 line. The table includes a brief description of each task a ...

  • Lucent Technologies 7820-0802-003 - page 76

    7-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Over view of T1 conf igur ati on “ Confi guring i nband robbed-bi t signaling ” on pag e 7-1 1 If the lines use inband signaling, chan ge the sign aling mode t o robbed bit and specify the type of robbed bit signalin g to use. Y ou ...

  • Lucent Technologies 7820-0802-003 - page 77

    Configuring T1 Ca rds Overvi ew of T1 conf iguratio n APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 5 “ Confi guring na iled channels ” on page 7-21 Y ou must assig n a nailed ch annel to a group to m ake it available for use. The group nu mber can be refer red to in a Connectio n or Frame- Relay pro ...

  • Lucent Technologies 7820-0802-003 - page 78

    7-6 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Making a profile the working pr ofile Making a profile th e working profile When the T AOS unit detects that a T1 card has been installed, it creates a default T1 p rofile for each of the eigh t lines on the card. In the followin g dis ...

  • Lucent Technologies 7820-0802-003 - page 79

    Configuring T1 Ca rds Assi gning nam es to T1 li ne profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 7 nfas-group-id = 0 nfas-id = 0 incoming-call-handling = internal-processing call-by-call = 0 data-sense = normal idle-mode = flag-idle FDL = none front-end-type = dsx DSX-line-length = 1-133 CSU-b ...

  • Lucent Technologies 7820-0802-003 - page 80

    7-8 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Enablin g a line Enablin g a line By default each T1 line is disabled. T o enable the T1 line, read its profile to m ake it the working profile, then set the Line Interface subpr ofile ’ s Enabled parameter to Y es, as in the followi ...

  • Lucent Technologies 7820-0802-003 - page 81

    Configuring T1 Ca rds Configur ing ISDN network-s ide emula tion APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 9 admin> set line switch-type = switchtype admin> set line channel 24 channel-usage=d-channel admin> write T1/{ shelf-1 slot-2 1} written T o see a complete list of switch types support ...

  • Lucent Technologies 7820-0802-003 - page 82

    7-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Conf ig ur in g over lap r eceiv ing on PRI line s trailing-digits = 2 t302-timer = 10000 [in E1/{ shelf-1 slot-12 1 }:line-inte rface] signaling-mode = isdn overlap-receiving = yes pri-prefix-number = 3069 trailing-digits = 2 t302-tim ...

  • Lucent Technologies 7820-0802-003 - page 83

    Configuring T1 Ca rds Config uring in band robbed- bit sig naling APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 1 The following exa mple enables overlap receiving on an E1 PRI line: admin> read e1 {1 16 7} E1/{ shelf-1 slot-16 7 } read admin> set signaling-mode = isdn admin> set overlap-receiv ...

  • Lucent Technologies 7820-0802-003 - page 84

    7-12 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configu ring inban d robbed- bit signal ing accounting. (On lines configu red fo r PRI sign aling, this inform ation is pr esented as part of the call setup message an d does not require special configur ation on the T AOS unit.) T o c ...

  • Lucent Technologies 7820-0802-003 - page 85

    Configuring T1 Ca rds Conf ig uri ng NF AS APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 3 Configuring NF AS A group of T1 lines configur ed for NF AS signaling shares a D channe l. One line in the group is configured with a primary D channel, and anoth er line is configur ed with a secondary D channel ...

  • Lucent Technologies 7820-0802-003 - page 86

    7-14 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Conf ig uri ng NF AS admin> read t1 {1 2 1} T1/{ shelf-1 slot-2 1 } read admin> set line signaling-mode = isdn-nfas admin> set line nfas-id = 0 admin> set line nfas-group-id = 1 admin> set channel 24 channel = nfas-prima ...

  • Lucent Technologies 7820-0802-003 - page 87

    Configuring T1 Ca rds Configur ing T1 R1 and R1-Modi fied (Taiw an) with A NI and cal led-number processin g APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 5 admin> write T1/{ shelf-1 slot-2 6 } written admin> read t1 {1 2 7} T1/{ shelf-1 slot-2 7 } read admin> set line signaling-mode = isdn-nf ...

  • Lucent Technologies 7820-0802-003 - page 88

    7-16 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configur ing T1 R1 and R1-Modi fied (Taiwa n) with ANI a nd called- number proc essing the switch, you can also specify how long it waits before send ing the request, and ho w long the ANIR sig nal l asts . The following par ameters en ...

  • Lucent Technologies 7820-0802-003 - page 89

    Configuring T1 Ca rds Config uring clo cking APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 7 Configuring clocking Y ou can configure the T AOS unit to use any of th e T1 lines as a ma ster phase-locked loo p (PLL) clock source f or synchro nous connections for an en tire sys tem. In synchr onous transm ...

  • Lucent Technologies 7820-0802-003 - page 90

    7-18 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configu ring ch annel us age T o specify CSU settings, proceed as in the following examp le after reading in the line ’ s T 1 profile: admin> set front-end-type = csu admin> set csu-build-out = 7.5-db admin> write Configurin ...

  • Lucent Technologies 7820-0802-003 - page 91

    Configuring T1 Ca rds Assi gning tel ephone num bers to swi tched ch annels APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 9 Assigning telephone numbers to switched channels Channel assignment s typicall y specify add -on nu mbers, not fu ll telep hone nu mbers. Ad d-on numbers include only the rightmo ...

  • Lucent Technologies 7820-0802-003 - page 92

    7-20 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configu ring trunk gr oups admin> set 13 phone = 72 admin> write Configuring trunk groups Like nail ed channels t hat have b een assigned a group number , switched channels in a t runk group can be referred to from a Connection p ...

  • Lucent Technologies 7820-0802-003 - page 93

    Configuring T1 Ca rds Configur ing nail ed channe ls APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-2 1 phone-number = "" call-route-info = { any-shelf any-slot 0 } nailed-group = 0 admin> set trunk-group = 4 admin> write Note: Command h istory is very useful for repeat ing comm ands. Pres ...

  • Lucent Technologies 7820-0802-003 - page 94

    7-22 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Specify ing anal og encoding f or TAOS unit code cs • Clock-Source set to Eligible (the default) In T1 profile for the other end of the line, specify the following values: • Signaling -Mode set to Inband (the defau lt) • Robbed-B ...

  • Lucent Technologies 7820-0802-003 - page 95

    Configuring T1 Ca rds Sample T1 conf igurat ion APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-2 3 Sample T1 config uration This section provides an example of h ow to configure a T1 slot card. The example uses the following setu p: • The card is in shelf 1, slot 2. • All lines use PRI sig naling. • ...

  • Lucent Technologies 7820-0802-003 - page 96

    7-24 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Default Call-Route p rofiles 4 Enable the line: admin> set enabled = yes 5 Set the frame type: admin> set frame-type = est 6 Set the line encoding: admin> set encoding = b8zs 7 Set the signaling m ode: admin> set signaling- ...

  • Lucent Technologies 7820-0802-003 - page 97

    APX 8000 Physical Interface Configuration Guide Preli minary M ay 9, 2000 8-1 8 Configur in g T1 FrameLine Card s (MAX TNT , DSL TNT) Introduction to T1 FrameLine The T1 FrameLine slot card provides 10 unchannelized T1 lines, each of which can be used f or one nailed connection. Associated with each T1 lin e is a Serial Communications Adapter (SCA) ...

  • Lucent Technologies 7820-0802-003 - page 98

    8-2 Preliminary May 9 , 2000 APX 8000 Physical Interface Configuration Guide Configuring T1 FrameLine Cards (MAX TNT, DSLTNT) Over view of T1 Fra meLi n e co nfi gur ati on • Multilink Protocol (MP) and Multil ink Protocol Plus (MP+) are no t su ppo rted. The connection profile must speci fy only P PP . • Users are authenticated b y the local p ...

  • Lucent Technologies 7820-0802-003 - page 99

    Configuring T1 FrameLine Cards (MAX TNT, DSLTNT) Configur ing the c lock sourc e APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 8- 3 – Call- by-Call – Channel-Usage – Defa ult-C all- T y pe – Data Sense – FDL – Idle-Mod e – Maintenance-St ate – NF AS-ID – Robbed-B it-Mode – SendDisc-V al ...

  • Lucent Technologies 7820-0802-003 - page 100

    ...

  • Lucent Technologies 7820-0802-003 - page 101

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 9- 1 9 Configu ring E1 Cards Introduction to E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9- 2 Overview of E1 co nfiguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Lucent Technologies 7820-0802-003 - page 102

    9-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Introduc tion to E1 Introduction to E1 An E1 line suppor ts 32 64Kbps channels , each of which can be used to transm it and receive data or d igitiz ed voice. The line uses framing an d signaling to achieve synchron ous and reliable tr ...

  • Lucent Technologies 7820-0802-003 - page 103

    Configuring E1 Cards Overvi ew of E1 configu ration APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 3 “ Confi guring a back-t o-back connection ” on page 9-7 A back-to-back connection lets yo u connect two T AOS units to one an other over a crossover E1 cable. Back-to-Back “ Specifying the framing ? ...

  • Lucent Technologies 7820-0802-003 - page 104

    9-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Understa ndi ng co nfig urati on re qui remen ts Understanding co nfi guration requirements Y ou need the follo win g information from your E1/P RI ser vice provider: • The telephone n umbers assigned to your E1/PRI interface, channe ...

  • Lucent Technologies 7820-0802-003 - page 105

    Configuring E1 Cards Making a profil e the work ing prof ile APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 5 • Rate adapt ion pr otocol — DASS 2 and DPNSS only (X.30 and V .110) Note: The T AOS unit cannot receive multichannel calls using Multilin k P rotocol (MP) encapsulation unless all channels of ...

  • Lucent Technologies 7820-0802-003 - page 106

    9-6 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Assign ing names to E1 li ne profiles line-interface = { no none g703 eligible middle-priority + back-to-back = false [in E1/{ shelf-1 slot-15 5 }:line-interface] enabled = yes t-online-type = none frame-type = g703 clock-source = elig ...

  • Lucent Technologies 7820-0802-003 - page 107

    Configuring E1 Cards Enabling a line APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 7 admin> read e1 {1 12 0} admin> set name = E1 Trunk admin> write E1/{ shelf-1 slot-12 0 } written admin> dir e1 17 04/17/1997 19:00:02 { shelf-1 slot-12 0 } "E1 Trunk" For E1 lines , the Line S tatus ...

  • Lucent Technologies 7820-0802-003 - page 108

    9-8 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Specify ing E1 s ignalin g admin> set line frame-type = [ G703 | 2DS | D4 | esf ] admin> write E1/{ shelf-1 slot-2 1 } written Specifying E1 signalin g An E1 lin e ’ s si gna l ing mo de can be an y o f the f ollow i ng: • IS ...

  • Lucent Technologies 7820-0802-003 - page 109

    Configuring E1 Cards Configur ing ISDN network-s ide emula tion APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 9 Configure ISDN PRI service as in the following example: admin> read e1 {1 15 5} E1/{ shelf-1 slot-15 5 } read admin> list [in E1/{ shelf-1 slot-15 5 }] name = "" physical-addres ...

  • Lucent Technologies 7820-0802-003 - page 110

    9-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Configu ring E1 R1 signalin g ISDN emulation enables you to build, s end, receive, and p rocess ISDN data. ISDN mon itoring, on the other h and, all ows you on ly to decode the ISDN data. Configuring E1 R1 si gnali ng R1 is a mu ltifre ...

  • Lucent Technologies 7820-0802-003 - page 111

    Configuring E1 Cards Configu ring E1 R2 s ignalin g APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 1 T o configure the line f or R2 signaling, p roceed as in the following example: admin> read e1 {1 2 2} E1/{ shelf-1 slot-2 2 } read Number- Com plete Number of digits considered to be a comp lete numb ...

  • Lucent Technologies 7820-0802-003 - page 112

    9-12 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Conf ig urin g DP NSS si gnal ing admin> list line enabled=no frame-type=g703 clock-source=eligible clock-priority=middle-priority signaling-mode=isdn switch-type=net5-pri front-end-type=short-haul channel-config=[ { unused-channel ...

  • Lucent Technologies 7820-0802-003 - page 113

    Configuring E1 Cards Configur ing ove rlap rece iving on PRI li nes APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 3 admin> set loop-avoidance = 7 admin> write Configuring overlap receiving on PRI lin es Overlap receiving af fects the procedure of establishing an incoming call received on a T1 or ...

  • Lucent Technologies 7820-0802-003 - page 114

    9-14 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Configu ring ch annel us age Configuring channel usage Y ou must specify how each o f the 32 channels of an E1 line is to be us ed. By defau lt, E1 channels are config ured as switched. Each of the 32 channels of an E1 line can be conf ...

  • Lucent Technologies 7820-0802-003 - page 115

    Configuring E1 Cards Configur ing nail ed channe ls APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 5 idle-logout = 0 parallel-dialing = 2 single-file-incoming = yes analog-encoding = a-law sessionid-base = 0 admin> set use-trunk-groups = yes admin> write Then assign the channels of each E1 line to ...

  • Lucent Technologies 7820-0802-003 - page 116

    9-16 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Specify ing anal og encoding f or TAOS unit code cs When you conf igure Connection profiles to use the leas ed connection, y ou must specify the Nailed-G roup num ber in the T elco-Opti ons subp rofile. T o configure a nailed c hannel, ...

  • Lucent Technologies 7820-0802-003 - page 117

    Configuring E1 Cards Default Cal l-Route p rofiles APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 7 This defaul t Call- Route pro file rout es outbo und trun k calls t o any line o n the card. T o handle inbound m odem and LAN-sessio n traf fic, you must con figure speci fic call ro utes. For d etails, ...

  • Lucent Technologies 7820-0802-003 - page 118

    ...

  • Lucent Technologies 7820-0802-003 - page 119

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 10-1 10 Configur in g E1 Frame Line Cards (MAX TNT , DSL TNT) Introduction to E1 FrameLine The E1 FrameLine sl ot card provides 1 0 E1 FrameLine lines, each of which can be used for one nailed connection. Associated with each E1 lin e is a Serial Communications Adapter (SCA), which is ...

  • Lucent Technologies 7820-0802-003 - page 120

    10-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Overvie w of E1 FrameL ine confi gurat ion PPP The E1 FrameLine sl ot card supports PPP as follows : • Only one PPP s essi on per li ne. • Bandwidth per ses sion is 1-3 1 DS0 ch annels. Chann el 1 is no ...

  • Lucent Technologies 7820-0802-003 - page 121

    Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Over vie w of E 1 Fra meL ine con fig ur ation APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 10-3 • Channel-Usage for chan nel must be set to Unus ed-Channel. • For all other channels, Channel-Us age must be set to either Unused-Chann el or Nailed-6 4-Channel. • Chan nel 17 is ...

  • Lucent Technologies 7820-0802-003 - page 122

    10-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Adminis trative profile s for E1 F rameLin e hunt-grp-phone-number-2 = "" hunt-grp-phone-number-3 = "" T o configure the E1 FrameLine card: admin> read E1 {1 2 2} UE1/{ shelf-1 slot-2 ...

  • Lucent Technologies 7820-0802-003 - page 123

    Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Adminis tr ati v e comm and s and sta tus infor ma tio n APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 10-5 Admin-S t ate profile When you install the E1 FrameLine slot card, the MAX TNT or DSL TNT creates 20 Admin-St ate profiles; 10 are associated with the E1 lines and 10 are asso ...

  • Lucent Technologies 7820-0802-003 - page 124

    10-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Conf ig uri ng th e c lock sou r ce Conf iguring the cloc k sour ce The E1 FrameLine s lot card uses the same system-wide PLL s ynchronous clo ck source fo r DS1 transmission as do the eight-port T1 and E1 c ...

  • Lucent Technologies 7820-0802-003 - page 125

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 11- 1 11 Configur in g T3 Cards Introduction to T3 The T3 slot card is a communications circuit composed of seven DS2s, each o f which includes four DS1 s, each of w hich in t urn is compo sed of 24 DS0s, for a total of 672 DS0 chan nels. On the T3 card, DS2 c ...

  • Lucent Technologies 7820-0802-003 - page 126

    11-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T3 Cards Understa nding T3 c onfiguration requir ements For complete infor mation about the as sociated parameters, see the APX 8 000/MAX TNT/DSLTNT Reference . Understanding T3 configu ratio n requ irements Config urin g the T3 slot card is v ...

  • Lucent Technologies 7820-0802-003 - page 127

    Configuring T3 Ca rds Unders tanding T3 slot c ard profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 11- 3 Understanding T3 slot card profiles When the T AO S unit first detects the pr esence of a T3 slot card, it creates the following profiles for each card: • One T3 profile • One Call-R oute pr ...

  • Lucent Technologies 7820-0802-003 - page 128

    11-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T3 Cards Assign ing a name to a T3 p rofile 13 02/28/1997 10:54:49 { { { she lf-1 slot-8 0 } 0 } 0 } 13 02/28/1997 10:54:49 { { { she lf-1 slot-11 0 } 0 } 0 } 13 02/28/1997 10:54:49 { { { she lf-1 slot-16 0 } 0 } 0 } 13 02/28/1997 10:54:49 { { ...

  • Lucent Technologies 7820-0802-003 - page 129

    Configuring T3 Ca rds Enabling a line APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 11- 5 admin> read t3 {1 12 0} admin> set name = T3 Trunk admin> write T3/{ shelf-1 slot-12 0 } written admin> dir T3 17 04/17/1997 19:00:02 { shelf-1 slot-12 0 } "T3 Trunk" For T3 lines, the Line S tat ...

  • Lucent Technologies 7820-0802-003 - page 130

    ...

  • Lucent Technologies 7820-0802-003 - page 131

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary May 9, 2000 12- 1 12 Confi gurin g Serial W AN (SW AN) Cards (MAX TNT, DSL TNT) Introduction to SW AN The Serial W AN (SW AN) card, has four V .35 serial ports, which can be used for nailed Frame Relay connections. This card can support u p to 120 Frame Relay virtual circu ...

  • Lucent Technologies 7820-0802-003 - page 132

    12-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Understa nding SW AN card configurati on requi rements For complete infor mation about the associated param eters, see the APX 8000 /MAX TNT/DSLTNT Reference . Understanding SW AN card configuration requ ...

  • Lucent Technologies 7820-0802-003 - page 133

    Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Making a profil e the work ing prof ile APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 12- 3 Making a profile th e working profile When the T AO S unit detects that a SW AN card has been installed, it cre ates a default SW A N profile for each of the li ...

  • Lucent Technologies 7820-0802-003 - page 134

    12-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Assign ing a name to a SWA N profil e clocking clock-mode = external-clock divider = 1 exp = 2 Assigning a name t o a SW AN profile In a SW AN profile, the Name p arameter enables you to assi gn the prof ...

  • Lucent Technologies 7820-0802-003 - page 135

    Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Spec ifyi ng th e SWAN i n ter nal cl ock speed APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 12- 5 Specifying the SW A N inter nal clock speed The SW AN slot card can generate a tran smit or receive internal clock based o n the clock speed of its Seri ...

  • Lucent Technologies 7820-0802-003 - page 136

    12-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Frame Rela y co nfi gur atio n divider = 1 exp = 2 5 Specify the Divider and exponent to u se for calculating the clock s peed: admin> set divider=4 admin> set exp=2 6 W r ite th e profile: admin&g ...

  • Lucent Technologies 7820-0802-003 - page 137

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 13 Confi gur ing Unchannelized DS3 Cards (MAX TNT , DSL TNT) Introduction to unch annelized DS3 The unchannelized DS3 slot card (UDS3), supported on the MAX TNT and the DSL TNT, is a 44.736Mbps communications circuit that can b e used to conce ntrate incoming traffi c on the unit and d ...

  • Lucent Technologies 7820-0802-003 - page 138

    13-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Unchannelized DS3 Cards (MAX TNT, DSLTNT) Overvie w of uncha nnelized DS3 configu ration Overview of unchannelized DS3 configura tion T able 9-1 lists the sectio ns descri bing com mon tasks you might have t o perform t o conf igure an unchann ...

  • Lucent Technologies 7820-0802-003 - page 139

    Configuring Unchannelized DS3 Cards (MAX TNT, DSLTNT) Conf ig uri ng th e UD S3 p hysi cal lin k APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 13- 3 By default, each un channelized DS3 line is disa bled. When the DS3 interface is dis abled, it transmits the DS3 Idle Sig n al to the far end. T o assign the ...

  • Lucent Technologies 7820-0802-003 - page 140

    ...

  • Lucent Technologies 7820-0802-003 - page 141

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 14-1 14 Configu r ing DS3 -A T M Cards Introduction DS3-A TM The DS3-A TM cards (DS3-A TM and DS3- A TM2) suppo rt one 44.736 Mbps interface fo r connecting to o ne A TM switch. At a minimum, yo u must enable the line and specify a n ailed group. T AOS units use the nailed group to dir ...

  • Lucent Technologies 7820-0802-003 - page 142

    14-2 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DS3-ATM Cards Over view of DS 3-AT M set tin gs [in DS3-ATM/{ any-shelf any-slot 0 }:l ine-config] trunk-group = 9 nailed-group = 1 activation = static call-route-info = { any-shelf any-slot 0 } loopback = no-loopback high-tx-output = no framer-mode = C-BIT-PLCP vpi-vci ...

  • Lucent Technologies 7820-0802-003 - page 143

    Configuring DS3-ATM Cards Examp les of DS3 -ATM config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 14-3 Examples of DS3-A TM c onfigurations The following set of commands enables a DS3-A TM interface in slot 12 and assigns the nailed group nu mber 1 1 1. admin> read ds3-atm {1 12 1} DS3-ATM/{ shelf-1 12 1 } read admi ...

  • Lucent Technologies 7820-0802-003 - page 144

    14-4 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DS3-ATM Cards Example s of DS3-AT M confi guration s Looping back the line T o diagnose possible line pr oblems, you can loop back the DS3-A TM interface by using the Loopback p arameter in the line profile. While the interface is looped back, normal data tr affic is in ...

  • Lucent Technologies 7820-0802-003 - page 145

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary May 9, 2000 15- 1 15 Configu r in g OC3-A TM Cards (MAX TNT/DSL TNT) Introduction to OC3-A TM An OC3-A TM card pr ovides one 155 .52Mbps interface f or connecting to an A TM switch. At a minimum, you must enable the line and specify a nailed group. MAX TNT and DSL TNT unit ...

  • Lucent Technologies 7820-0802-003 - page 146

    15-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring OC3-ATM Cards (MAX TNT/DSLTNT) Over view o f O C3-A TM s ett ing s rx-descramble-disabled = no tx-scramble-disabled = no rx-cell-payload-descramble-disabled = no tx-cell-payload-scramble-disabled = no loop-timing = yes vpi-vci-range = 0-15/32-40 ...

  • Lucent Technologies 7820-0802-003 - page 147

    Configuring OC3-ATM Cards (MAX TNT/DSLTNT) Using O C3-ATM p orts as a clock source APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 15- 3 Using OC3 -A TM ports as a clock so urce OC3-A TM profiles support Clock -Source and Clock -Priority p arameters f or specify ing whether the port c an be used to s ource ...

  • Lucent Technologies 7820-0802-003 - page 148

    15-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring OC3-ATM Cards (MAX TNT/DSLTNT) Example of an OC3 -ATM con figur ation For example, the f ollowing commands configure an OC3-A TM port as an eligible clock source. If this port becomes unavailab le and is not back ed up, the unit begins using the ...

  • Lucent Technologies 7820-0802-003 - page 149

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 16- 1 16 Configu ring ST M-0 Ca rds Introduction to STM-0 The Synch ronous T ransport Mo dule (STM)-0 ca rd is an o ptical 51 .85Mbps com munication circuit designed to be used with an approved signaling gateway . Each of its 28 T1 lines can be configu red as ...

  • Lucent Technologies 7820-0802-003 - page 150

    16-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring STM-0 Cards Usi ng S TM an d T1 pr ofiles Using STM and T1 profiles When the T AO S unit first detects the pr esence of an STM-0 card, it creates a default STM profile for the card as well as 28 T1 p rofiles for each component T1 line. The foll ...

  • Lucent Technologies 7820-0802-003 - page 151

    Configuring STM-0 Cards Sample S TM-0 con figurati ons APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 16- 3 Example of configuring a T1 dat a trunk The following command s configure a T1 line as an SS7 data tru nk, enabling the si gnaling gateway to control the line: admin> read t1 {1 1 7} T1/{ shelf-1 s ...

  • Lucent Technologies 7820-0802-003 - page 152

    ...

  • Lucent Technologies 7820-0802-003 - page 153

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary May 9, 2000 17- 1 17 Configu r in g DSL Connections (DSL TNT) Introduction to DSL technologies Three types of Digital Subscriber Line (DSL) cards are available for the DSL TNT. These cards support either Asymmetr ic Dig ital Subscriber Line (ADSL), ISDN Digital Subscrib er ...

  • Lucent Technologies 7820-0802-003 - page 154

    17-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Introduc tion to DSL technolo gies The IDSL line card pr ovides the following featu res: • ISDN BRI (2B1Q) signaling • T wo DB37 connectors, each providing 16 IDSL sessions f or a total of 3 2 sessions • 128Kbps u ...

  • Lucent Technologies 7820-0802-003 - page 155

    Configuring DSL Connections (DSLTNT) Introduc tion to DSL te chnologi es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 3 SDSL overview The SDSL card suppor ts symmetric data tran sfer rates of 768 Kbps for a distance of up to 12,000 f eet (3.7 km) ov er a single pair of copper wires. The SDSL-HS data ...

  • Lucent Technologies 7820-0802-003 - page 156

    17-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) DSL confi guration For complete details o f configuring authen tication or Frame Relay and PPP connections on your DSL TNT, see the APX 8000 /MAX TNT/DSL T NT W AN, Routing and T unneling Configurati on Gu ide and the A ...

  • Lucent Technologies 7820-0802-003 - page 157

    Configuring DSL Connections (DSLTNT) Configur ing nail ed connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 5 • Set the Dial # parameter in the Configure prof ile to the DS L po rt number, which in the case of a single DSLPipe is always 1. T o configure a s witched connection on the DSL TNT ...

  • Lucent Technologies 7820-0802-003 - page 158

    17-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig uri ng d ata t ra n s fer rate s Configuring data transfer rates Y ou can configure DSL upstream and d ownstream rates in the line p rofiles fo r each card, and in Connection or RADIUS profiles. The data transfe ...

  • Lucent Technologies 7820-0802-003 - page 159

    Configuring DSL Connections (DSLTNT) Config uring da ta transf er rates APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 7 For example, if the transceiver is configu red for 108 800 0bps and th e loop qu ality is so poo r that the transceiver will not connect to the remote side, the transceiver does not ...

  • Lucent Technologies 7820-0802-003 - page 160

    17-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig uri ng d ata t ra n s fer rate s T o configure the max imum transfer ra te for the 24 -port SDSL card: 1 Open the SDSL profile: admin> read sdsl {2 1 7} SDSL/{ shelf-2 slot-1 7 } read 2 Enable the line: admin ...

  • Lucent Technologies 7820-0802-003 - page 161

    Configuring DSL Connections (DSLTNT) Config uring da ta transf er rates APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 9 For more information about thes e parameters, see the APX 8000/MAX TNT/DSL TNT Refer ence . Config uring pe r -se s sion dat a rate s using mode m rate co ntrol In the following exam ...

  • Lucent Technologies 7820-0802-003 - page 162

    17-10 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig uri ng d ata t ra n s fer rate s admin> set session ses-rate-type = adsl-cap admin> set session ses-adsl-cap-down-rate = 7168000 admin> write CONNECTION/adslpipe-1 written Following is a comparable R A ...

  • Lucent Technologies 7820-0802-003 - page 163

    Configuring DSL Connections (DSLTNT) Config uring da ta transf er rates APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -11 LOG info, Shelf 1, Controller, Time: 16:47:11-- [1/7/1/1] Incoming Call [MBID 18] LOG info, Shelf 1, Controller, Time: 16:47:11-- [1/7/1/0] Assigned to port [MBID 18] LOG info, Shelf ...

  • Lucent Technologies 7820-0802-003 - page 164

    17-12 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Configu ring DSL Pipe Plug a nd Play LOG info, Shelf 1, Controller, Time: 16:47:34-- [1/7/1/0] Assigned to port [MBID 19] LOG info, Shelf 1, Controller, Time: 16:47:34-- [1/7/1/1] Call Connected [MBID 19] LOG info, She ...

  • Lucent Technologies 7820-0802-003 - page 165

    Configuring DSL Connections (DSLTNT) Configur ing DSLP ipe Plug and Play APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -13 Figur e 1 7-1. DSLPipe unit obtaining its con figuration (Plug and Play) The DSLPipe unit uses the m inimal configuration it ob tains via DHCP to access the specified TF TP server an ...

  • Lucent Technologies 7820-0802-003 - page 166

    17-14 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Configu ring DSL Pipe Plug a nd Play TFTP Host Name=host-1.abc.com Boot File Path=/tftpboot/config For a Pipeline unit to op erate as a DHCP server , DHCP Spoofing and Always Spoof must be set to Y es. T o enable the s ...

  • Lucent Technologies 7820-0802-003 - page 167

    Configuring DSL Connections (DSLTNT) Configur ing DSLP ipe Plug and Play APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -15 Configuring the DSL TNT DSLPipe Plug and Play suppor t requires the fo llowing configu ration on the DSL TNT: • BOOTP Re lay enable d • A nailed DSL connection to the DSLPipe • ...

  • Lucent Technologies 7820-0802-003 - page 168

    17-16 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Configu ring DSL Pipe Plug a nd Play 1 Read in the SDSL prof ile. For example, if the SDSL card is installed in s helf 1, slot 1 1 , and the remote DSLPipe is connected to por t 1: admin> read sdsl {1 3 1} SDSL/{ sh ...

  • Lucent Technologies 7820-0802-003 - page 169

    Configuring DSL Connections (DSLTNT) Configu ring IDSL v oice connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -17 6 W r ite th e profile: admin> write FRAME-RELAY/fr written Config uring a Co nn ectio n profile This example Conn ection profile uses the Frame Relay pr ofile configured in the ...

  • Lucent Technologies 7820-0802-003 - page 170

    17-18 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig ur in g IDSL voic e conn ect ions Figur e 17-2. Incomi ng and o utgoing vo ice calls Incoming calls Incoming IDSL voice calls requir e that the C entral Of fice (CO) switch support Dialed Number Identification ...

  • Lucent Technologies 7820-0802-003 - page 171

    Configuring DSL Connections (DSLTNT) Configu ring IDSL v oice connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -19 1 Read the IDSL pro file the remote user is connected to. For example : admin> read idsl {1 7 29} IDSL/{ shelf-1 slot-7 29 } read 2 List the IDSL prof ile: admin> list name = ...

  • Lucent Technologies 7820-0802-003 - page 172

    17-20 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig ur in g IDSL voic e conn ect ions remote-address = 0.0.0.0/0 local-address = 0.0.0.0/0 .. .. 5 Specify the Pipeline IP addr ess: admin> set remote-address=192.1.2.1/24 6 List the T e lco -Options profile: ad ...

  • Lucent Technologies 7820-0802-003 - page 173

    Configuring DSL Connections (DSLTNT) Configu ring IDSL v oice connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -21 techpubs-lab-25> list line-interface channel-config [in T1/{ shelf-1 slot-1 1 }:line-inter face:channel-config] channel-config[1] = { switched-channel 9 "" { any-shelf ...

  • Lucent Technologies 7820-0802-003 - page 174

    17-22 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations – My Name= buffer – My Addr= 192.1.2.1/24 – Rem Name= bufferstnt – Rem Addr= 192.1.1.1/24 – Route= IP 3 Exit and s ave the Co nfigure p rofile. 4 Open Ethernet > Conn ections &g ...

  • Lucent Technologies 7820-0802-003 - page 175

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -23 Configuri ng the DSL TNT This example assumes the DSL TNT has already been configured with the followin g information: • IP address of 192 .1.1 4/24 • System name of idsltnt T o configur ...

  • Lucent Technologies 7820-0802-003 - page 176

    17-24 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations admin> write Confi gu rin g the ID SL pr ofi le T o configure the DSL TNT IDSL profile, proceed as in the following example: 1 Read the IDSL pro file that the remote user is co nnected to ...

  • Lucent Technologies 7820-0802-003 - page 177

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -25 admin> write Configu ring a static route t o the gateway T o configure a static route to the gateway: 1 Read in the IP-Route Default profile: admin> read ip-route default 2 Enter the a ...

  • Lucent Technologies 7820-0802-003 - page 178

    17-26 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations – Name= idsl-fr – Active= Yes – Call T ype = Nailed – Nailed Grp= 1 3 Exit the Frame R elay profile and s ave your chan ges. Note that the Pipeline uses th e follo win g nailed group ...

  • Lucent Technologies 7820-0802-003 - page 179

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -27 Confi gur ing t he ADSL prof ile T o configur e the ADSL profile in this example: 1 Read in the ADSL pro file: admin> read adsl-cap {1 7 3} 2 Enable the port: admin> set enabled=yes 3 ...

  • Lucent Technologies 7820-0802-003 - page 180

    17-28 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations 6 V erify that IP routing is enabl ed (the default) for this Connection profile: admin> set ip-routing-enabled = yes 7 V erify that VJ header predictio n is not en abled for this Connecti ...

  • Lucent Technologies 7820-0802-003 - page 181

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -29 2 Specify the following valu es: – Chan Usage= Leased/Unused – My Name= dslpipe – My Addr= 10.10.73.1/24 – Rem Name= max-tnt – Rem Addr= 104.178.115.163/24 – Route= IP – Bridge ...

  • Lucent Technologies 7820-0802-003 - page 182

    17-30 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations Figur e 17-5. E xample S DSL setup with in terface -based r out ing Configuring an SDSL conn ection requires the following gene ral step s: • Configuring the Connectio n profile • Config ...

  • Lucent Technologies 7820-0802-003 - page 183

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -31 admin> set local-address=192.168.23.142/30 7 List the subm enu for Frame Relay optio ns: admin> list .. fr-options [in CONNECTION/sdsl-pipeline:fr-option s] frame-relay-profile = " ...

  • Lucent Technologies 7820-0802-003 - page 184

    17-32 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations Confi gur ing t he SDSL prof ile T o configure the SDSL profile : 1 Read in the SDSL prof ile. For example, if the SDSL card is installed in s lot 1 1 of shelf 1 and the remote DSLPipe-S is ...

  • Lucent Technologies 7820-0802-003 - page 185

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -33 Conf igur ing t he D SLPip e-S This section provides an example of co nfiguring the SDSL Pipelin e (DSLPipe-S). For complete informa tion about configuring the DSLPipe-S, s ee the documentat ...

  • Lucent Technologies 7820-0802-003 - page 186

    17-34 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations 2 Specify the following valu es: – Name= Frame Relay – Active= Yes – Call Type= Nailed 3 If your Pipeline supports it, set Lin kUp to Y es: – LinkUp= Yes Note that this parameter doe ...

  • Lucent Technologies 7820-0802-003 - page 187

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -35 3 Specify the encapsulation ty pe as Frame Relay: admin> set encapsulation-protocol=frame-relay 4 List the IP -Optio ns submen u: admin> list ip-options [in CONNECTION/sdsl-pipeline:ip ...

  • Lucent Technologies 7820-0802-003 - page 188

    17-36 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations Confi gur ing t he SDSL prof ile T o configure the SDSL profile : 1 Read in the SDSL prof ile. For example, if the SDSL card is installed in s lot 1 1 of shelf 1 and the remote DSLPipe-S is ...

  • Lucent Technologies 7820-0802-003 - page 189

    Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -37 Before you configure the Pip e lin e, make sure of the following: • The PC connected to the Pipeline has an I P address on the s ame subnet as the Pipeline. • The IP address of the Pipel ...

  • Lucent Technologies 7820-0802-003 - page 190

    ...

  • Lucent Technologies 7820-0802-003 - page 191

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 18- 1 18 Signali ng System 7 (SS7) Introduction to SS7 Signalin g S yst em 7 ( SS7) i s an i ntern ationall y st and ardi zed gener a l-pur pos e co mmon -chan nel signaling system designed for use ov er a variety o f digital circuit -switched net works . At t ...

  • Lucent Technologies 7820-0802-003 - page 192

    18-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) System requireme nts for SS7 operatio ns System requirements for SS7 oper ations A T AOS unit config ured for SS7 in communication with an SS7 signaling gateway is a service switching point (SSP) . T o operate in th is cap acity , ...

  • Lucent Technologies 7820-0802-003 - page 193

    Signaling System 7 ( SS7) System requirem ents for SS 7 operations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 3 T AOS unit as te rminator of voice and dat a calls in an SS 7 network W ith the IPDC license, the T AO S unit can communicate with th e signaling g ateway by means of IPDC. IPDC enables th ...

  • Lucent Technologies 7820-0802-003 - page 194

    18-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway See MultiV oice for MAX TNT Configuration Guide for a m ore detailed des cription of how V oIP calls are processed by IPDC. Interface between a signal ing gateway and T AOS unit TCP/IP is th ...

  • Lucent Technologies 7820-0802-003 - page 195

    Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 5 Settings in the SS7-Gateway profile con figure the signaling interf ace. The T A OS unit resets the signaling link whenever changes ar e written to the profile. Following are the para met er ...

  • Lucent Technologies 7820-0802-003 - page 196

    18-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway Specifying the SS7 control protocol W ith the appropria te sof tware lic ense, T AOS supports eit her ASGCP an d IPDC 0.1 2 control protoco l. If onl y one of t he poss ible con trol p rotoc ...

  • Lucent Technologies 7820-0802-003 - page 197

    Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 7 System IP address consider ati ons The System-IP-Addr par ameter of the IP-G lobal profile specifies the sou rce address of all packets gener ated by the system, s uch as the connection requ ...

  • Lucent Technologies 7820-0802-003 - page 198

    18-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway For so me sites, ad ministrativ e policy or other constraints introduce a requirement to use t he system addres s for some pur poses, bu t to use a separ ate source addr ess for commun icati ...

  • Lucent Technologies 7820-0802-003 - page 199

    Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 9 [in T1/{ shelf-1 slot-1 7 }:line-inter face:channel-config:24] channel-usage = switched-channel Exam ple of c onfig uring a T3 ca rd fo r SS7 da ta T o configure lines of a T3 car d as SS7 d ...

  • Lucent Technologies 7820-0802-003 - page 200

    18-10 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway admin> set line-interface enabled = yes admin> set line-interface signaling-mode = ss7-data-trunk admin> set line-interface incoming-call-handling = inter- nal-processing admin> ...

  • Lucent Technologies 7820-0802-003 - page 201

    Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-11 For example, the following com mands con figur e an E1 line as an SS7 data trunk, ena bling the signaling gateway to control th e line: admin> read e1 {1 10 1} E1/{ shelf-1 slot-10 1 } re ...

  • Lucent Technologies 7820-0802-003 - page 202

    18-12 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway per-line basis. Both the native 2-wire continuity check (GR-246-CORE Section B.2) and 4-wire-t o-2-wire emulation (GR-246-CORE Section B.3) are supporte d. Note: Outgoing contin uity tes ts ...

  • Lucent Technologies 7820-0802-003 - page 203

    Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-13 T AOS also supports the 4-wire- to-2-wire continuity ch eck, with the following req uirements: The exchang e that terminates 4 wires must use a transmitting f requency of 1780 ± 20 Hz and a ...

  • Lucent Technologies 7820-0802-003 - page 204

    18-14 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway For examp le, the fol lowing string def ines a 1004hz t one at 227 48 ampli tude for 1 second: " 1004, 0, 22748, 1000 " The follo wing stri ng defines a d ual tone with fre quency ...

  • Lucent Technologies 7820-0802-003 - page 205

    Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-15 ss7nmi de bug-l evel com mand The T AOS unit reports th e V oIP call statistics in the output of the ss7nmi debug- level command. When the comm and is entered with the -s option, the results ...

  • Lucent Technologies 7820-0802-003 - page 206

    18-16 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway Number of CONNECT to ASG: 0 Number of CONNECT_ACK from ASG: 0 Number of SETUP rejected from: L3: 0 CC: 0 Number of DISCONNECT requests fr om: L2: 0 CC: 0 Number of REGISTRATION to ASG: 0 Nu ...

  • Lucent Technologies 7820-0802-003 - page 207

    Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-17 Number of CONNECT to ASG T otal number of active connectio ns to the signaling gateway since it was last reset. Number of CONNECT_ACK from ASG Number of connection acknowledgements the T AOS ...

  • Lucent Technologies 7820-0802-003 - page 208

    18-18 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway Command outpu t showing errors The following sample in dicates that errors were detected in SS7 connections: admin> ss7asg -s SS7 Signaling Gateway interface statis tics: Initialized suc ...

  • Lucent Technologies 7820-0802-003 - page 209

    Signaling System 7 ( SS7) Cause co des fo r SS7 ASGC P call s to th e TAOS un it APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-19 Number of T308 expiry events: 0 Last L3 counters reset timestamp: [02/16/1999 10:33:31] Data Transport Layer: Number of link fail-overs: 0 Number of persistent errors: 0 Last ...

  • Lucent Technologies 7820-0802-003 - page 210

    18-20 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Cause co des for S S7 ASGC P call s to the T AOS un it • The T A OS unit reports User bus y (17) i f it cannot find a r oute, or if no reso urce is available for the call. SS7 IPDC support for call ID and disconnect cause codes ...

  • Lucent Technologies 7820-0802-003 - page 211

    Signaling System 7 ( SS7) Cause co des fo r SS7 ASGC P call s to th e TAOS un it APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-21 ft1-caller = 0 calling-number = { "" unknown unknown unspecified unspecified } force-56kbps = 0 redirect-number = "" call-direction = 0 global-call-id = 0 ...

  • Lucent Technologies 7820-0802-003 - page 212

    18-22 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Cause co des for S S7 ASGC P call s to the T AOS un it DIS_Q850_TEMPORARY_FAILURE 841 T emporary failure DIS_Q850_NETWORK_CONGESTION 842 Switching equipment conges tion DIS_Q850_ACCESS_INFO_DISCARDED 843 Access information discar ...

  • Lucent Technologies 7820-0802-003 - page 213

    Signaling System 7 ( SS7) SNMP s upport fo r SS7 APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-23 SNMP support for SS7 The SS7 MIB ( mgstat.mib) is implemented as a b ranch object with the main o bject, mgGroup , linked i nto t he As cend en ter pris e MIB. F or defi ni ti ons and descr ip ti ons of ob ...

  • Lucent Technologies 7820-0802-003 - page 214

    ...

  • Lucent Technologies 7820-0802-003 - page 215

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 19- 1 19 Confi gur in g Call Routi ng : The T A OS unit uses a set of call -routing algorith ms to ro ute inboun d and ou tbound calls to devices that handle the ap propriate call type. For example, the unit routes an inbound voice-service call to a mod em and ...

  • Lucent Technologies 7820-0802-003 - page 216

    19-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Understa nding the cal l-routing database Some slot cards act in a dual capaci ty , performing b oth network and hos t funct ions. Some dual-purpose cards provide their own HDLC reso urces. For examp le, T1 and E 1 FrameLine cards ...

  • Lucent Technologies 7820-0802-003 - page 217

    Configuring Call Routing Unde rsta ndi n g th e cal l-r outi ng databa se APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 3 How call routes affect device usage The system sorts its call-routing databa se en tries after a reset. During active use, the system applies operational criteria, such as availabil ...

  • Lucent Technologies 7820-0802-003 - page 218

    19-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Understa nding the cal l-routing database 3:1:4 ... The system uses the first modem on the lower -number ed card, then the first mo dem on the next card. It then u ses the second mo dem on each of the cards, and so forth. Th is sor ...

  • Lucent Technologies 7820-0802-003 - page 219

    Configuring Call Routing Working with Call-Ro ute profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 5 Hybrid Access card. See “ Dedicat ing Series 56 cards t o modem pro cessing ” on page 19-9 for related information . T runk li ne usage and sort ord er T runk lines are sorted in the order in ...

  • Lucent Technologies 7820-0802-003 - page 220

    19-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Working wi th Call-Rou te profil es Outbound call routing by trunk group If no exp licit call routes are defined, the T AOS unit always routes a call to the first entry in its database that matches the call ’ s parameters and is ...

  • Lucent Technologies 7820-0802-003 - page 221

    Configuring Call Routing Working with Call-Ro ute profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 7 W ith out an explicit call r oute for trunk group 8 , the system always tr ies the first E1 card, f inds that it d oes not use trun k group 8, and then drops t he call. The following com mands cr ...

  • Lucent Technologies 7820-0802-003 - page 222

    19-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Working wi th Call-Rou te profil es The next set o f commands creates an other Call-Route prof ile for the Hybr id Access card and sets the preferred source to the secon d E1 interface in s lot 2: admin> new call-route { { { she ...

  • Lucent Technologies 7820-0802-003 - page 223

    Configuring Call Routing Another way to ro ute incom ing calls (deprecat ed) APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 9 The following commands create a Call-R oute profile to rou te calls received on trunk group 4 to the Hybrid Access card in slot 4: admin> new call-route { { { 1 4 0 } 0} 0} CA ...

  • Lucent Technologies 7820-0802-003 - page 224

    19-10 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Call Routing Call rout ing algo rithms For example, the f ollowing commands specify that calls received o n the tenth T1 channel on line 1 of a card installed in shelf 1, slot 22 is always routed to the specified host d evice: admin> read t ...

  • Lucent Technologies 7820-0802-003 - page 225

    Configuring Call Routing Call routing algorithms APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 19-11 How the system finds a route After sorting the call-routing d atabase, the T AOS unit compares t he information i t has gathered about a call to the values in the da tabase, looking for a match. V alues are ...

  • Lucent Technologies 7820-0802-003 - page 226

    19-12 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Call Routing Call rout ing algo rithms Det ails of how a r oute is chosen The system comp ares call information to its database entries. The entries are accessed in th e order in which they are sorted, with devices that are us ed less frequent ...

  • Lucent Technologies 7820-0802-003 - page 227

    Configuring Call Routing Call routing algorithms APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 19-13 equal to the i npu t numb er , and its digits mus t match the add- on digits of the i np ut nu mber . For example, suppose the calling switch sent the fo llowing number to the T AOS unit: 555-1212 Profiles ...

  • Lucent Technologies 7820-0802-003 - page 228

    19-14 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Call Routing Call rout ing algo rithms voice service, all profiles that speci fy Digital-Call-T ype are removed from cons ideration. Only profiles that specify V oice-Call-T ype or Any-C all-T ype r e mai n in the list. Note: For T1 lines that ...

  • Lucent Technologies 7820-0802-003 - page 229

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 A- 1 A Provisioning the Switc h This appendix pr ovides th e information neces sary for p roperly p rovisioning a sw itch for T1/EI or T1/E1 PRI access to the W AN. Provisioning the switch for T1 access If you u se an inb and signaling line, the T1 circu it at t ...

  • Lucent Technologies 7820-0802-003 - page 230

    A-2 Prelimi nary May 9, 200 0 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide What you need from your T1 s ervice p rovider What you need from your T1 service provider Request the f ollowing infor mation about you r T1 interface from your W AN provider: • T ype of signal ing (inban d or ISD N D channel) • T ype of line enco ding ...

  • Lucent Technologies 7820-0802-003 - page 231

    APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Index-1 Index A ACM. See address complete mes sage (ACM) activation, for serial W AN card , 12-3 add-on nu mbers desc ribed , 7-19 specifying , 7-19 addresses requiring call to accept dyn amic , 1-9 used to route calls received on chann el , 19-13 used to route calls to a d evice , 19- ...

  • Lucent Technologies 7820-0802-003 - page 232

    Index-2 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide bearer capability and , 9-10 signalin g modes des cribed , 9-8 cause codes access S S7 gateway c ontro l protocol (ASGCP) calls , 18-19 disco nnect, sign aling s ystem 7 (S S7) supp ort f or call ID , 18-20 CCITT . See Co nsultative Com mi ttee for International T elephone and ...

  • Lucent Technologies 7820-0802-003 - page 233

    APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-3 serial W AN card configurati on requir ements , 12-2 setting date and time , 1-5 setting log level , 1- 5 shelf-contro ller redu ndan c y , 2-1 , 2-6 signaling interface parameter s , 18-5 sign a ling s ystem 7 (SS7) ga teway , 18-4 specifying defau lt gateway , 1-6 specifyi ...

  • Lucent Technologies 7820-0802-003 - page 234

    Index-4 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide DS3-A TM physical interface , 14-2 DS3-A TM port physi cal-a ddress , 14-2 DSL config uring naile d connect ions , 17-5 configuring switched co nnections , 17-4 data transfer rates, configuring , 17-6 enabling on ly active ports , 17-4 IDSL voice connections , 17-17 incoming ID ...

  • Lucent Technologies 7820-0802-003 - page 235

    APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-5 Ethernet configu ring full duplex m ode on E thernet-2 card , 4-3 installing Ethernet-2 card , 4-2 overview of Ether net card configuration , 4-2 related prof iles , 4-2 shelf cont roller and r outin g load , 1-4 shelf controller interface f or managem ent , 4-2 specifying d ...

  • Lucent Technologies 7820-0802-003 - page 236

    Index-6 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide I IAM. See initial address message (IAM) ICD. See Internet Call Diversion (ICD) ICMP redir ects, conf iguring s ystem to ig nore , 1-9 Idle mode for T1 lines , 7-5 , 7-22 IDS L incoming vo ice calls , 17-18 outg oing vo ice c alls , 17 -18 suppor ted CPE devi ces , 17-4 voice c ...

  • Lucent Technologies 7820-0802-003 - page 237

    APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-7 modems A T modem st rings , configur ing addi tional , 5-3 conf iguri ng V . 34 m odul atio n , 5-3 specifying nego tiation settings , 5-2 modulati on, conf iguring V .34 fo r 56K mod em , 5-3 MP/MP+ calls FrameLine card and , 8-2 , 10-2 multichannel calls disrup ted by fo r ...

  • Lucent Technologies 7820-0802-003 - page 238

    Index-8 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide T AOS default valu e , 18-6 Use-System-IP -Address-As-S ource , 18- 7 pass word s assigni ng to seri al port , 1-8 changing Admin , 1-8 not saved by defau lt , 1-8 SNMP comm unity strings , 1-1 1 Te l n e t , 1-8 perm i s s ions, A llow- Passwo rd not enab l e d by def ault , 1 ...

  • Lucent Technologies 7820-0802-003 - page 239

    APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-9 shelf -con troll er , 2- 6 shelf-control ler primary election , 2-1 shelf-control ler startup electio n , 2-1 robbed-bit config uration , 7-1 1 routing protoco ls supporte d by E1 F rameLine card , 10-2 protoco ls support ed by FrameLine car d , 8-2 shelf controlle r Ethern ...

  • Lucent Technologies 7820-0802-003 - page 240

    Index-10 APX 8000/MAX TNT/DSLTNT Physical Interface Co nfiguration Guide cause codes for access SS7 gateway control proto co (ASG CP) ca lls , 18-19 connections statistics , 18-15 connectio ns, error r eporting , 18-15 control protocol s pecification , 18-6 E1 lines as data trunks , 18- 10 gatewa y , confi guration , 18-4 incoming calls , 18-4 inte ...

  • Lucent Technologies 7820-0802-003 - page 241

    APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-11 usage , 7-4 , 7-18 T1 line continuity check, two -wire , 18-11 T1 lines assign ing name t o profi le , 7-7 call control for , 7-1 1 call control for line-sid e , 7-1 1 call control for trunk-sid e , 7-1 1 clock so urce and pri ority , 7-4 , 7-17 clo c king for , 7-17 conf i ...

  • Lucent Technologies 7820-0802-003 - page 242

    Index-12 APX 8000/MAX TNT/DSLTNT Physical Interface Co nfiguration Guide transport ser vice TCP/ IP , 18- 4 trans port-la yer options configuration , 18- 6 Tra p p f o f i l e sett i ng up , 2-1 1 Tra p p r o f i l e configuri ng , 2-11 trunk groups assigning to E1 chan nels , 9- 14 , 9-15 assigning to T1 chan nels , 7- 20 configuri ng , 7-20 expla ...

Manufacturer Lucent Technologies Category Wheelchair

Documents that we receive from a manufacturer of a Lucent Technologies 7820-0802-003 can be divided into several groups. They are, among others:
- Lucent Technologies technical drawings
- 7820-0802-003 manuals
- Lucent Technologies product data sheets
- information booklets
- or energy labels Lucent Technologies 7820-0802-003
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lucent Technologies 7820-0802-003.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lucent Technologies 7820-0802-003, service manual, brief instructions and user manuals Lucent Technologies 7820-0802-003. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lucent Technologies 7820-0802-003.

Similar manuals

A complete manual for the device Lucent Technologies 7820-0802-003, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lucent Technologies 7820-0802-003 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lucent Technologies 7820-0802-003.

A complete Lucent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lucent Technologies 7820-0802-003 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lucent Technologies 7820-0802-003, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lucent Technologies 7820-0802-003, that we can find in the current document
3. Tips how to use the basic functions of the device Lucent Technologies 7820-0802-003 - which should help us in our first steps of using Lucent Technologies 7820-0802-003
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lucent Technologies 7820-0802-003
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lucent Technologies 7820-0802-003 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lucent Technologies 7820-0802-003?

Use the form below

If you did not solve your problem by using a manual Lucent Technologies 7820-0802-003, ask a question using the form below. If a user had a similar problem with Lucent Technologies 7820-0802-003 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)