Manual Barco R9002038

45 pages 2.05 mb
Download

Go to site of 45

Summary
  • Barco R9002038 - page 1

    R9002031 R9002038 INST ALLA TION MANUAL DA T A 808s ...

  • Barco R9002038 - page 2

    BARCO PROJECTION SYSTEMS Date : 170397 Art. No. : R5975607 R9002031 R9002038 INST ALLA TION MANUAL DA T A 808s ...

  • Barco R9002038 - page 3

    Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, March 1997. All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium ...

  • Barco R9002038 - page 4

    Table of contents i-1 5975607 BARCODATA 808s 110397 TABLE OF CONTENTS .............................................................................................................. .................. I-1 SAFETY INSTRUCTIONS On saf ety ................................................................................................................... ...

  • Barco R9002038 - page 5

    Table of contents i-2 5975607 BARCODATA 808s 110397 Connecting a Component Video source to Port 4/5 ............................................................................. 7 - 3 Connecting a RGB Analog source with Tri-level sync to Port 4/5 (option) ............................................ 7 - 4 Connecting a Component Video source with T ...

  • Barco R9002038 - page 6

    Safety instructions 1-1 5975607 BARCODATA 808s 110397 1 SAFETY INSTRUCTIONS Projectors are built in accordance with the requirements of the international safety standards IEC950, UL 1950 and CSA C22.2 No. 950, which are the safety standards of information technology equipment including electrical business equipment. These safety standards impose im ...

  • Barco R9002038 - page 7

    Safety instructions 1-2 5975607 BARCODATA 808s 110397 unless proper ventilation is provided. On servicing Do not attempt to service this projector yourself, as opening or removing covers may expose you to dangerous voltage potential and risk of electric shock! Refer all projector service to a qualified BARCO service center. Call for service in the ...

  • Barco R9002038 - page 8

    Unpacking and dimensions 2-1 5975607 BARCODATA 808s 110397 2 UNP ACKING AND PROJECT OR DIMENSIONS Unpacking Contents of the shipping carton : ρ 1 BARCODATA 808s projector ρ 1 Remote Control Unit plus 1 battery 9V ρ 1 power cord with outlet plug type CEE7 or ANSI 73.11 ρ 1 Owner's Manual ρ 1 Installation Manual To open the banding around t ...

  • Barco R9002038 - page 9

    Unpacking and dimensions 2-2 5975607 BARCODATA 808s 110397 Projector dimensions (in mm) 1040 A 596 169. 5 ROTATION COVER *SERVICE* GRAVITY POINT CRT POINT 362 B 286 226 170 84 27 45.5 136 72 8 960 M AX 500 FIXATION POINT *4 X M8* MAX 10 76 AIRFLOW AIRFLOW AIRFLOW AIRFLOW 703 148 MAX 428 590 FRONT IR RECEIVE R 456 558 576 POWER SUPPLY BACK IR RECEIV ...

  • Barco R9002038 - page 10

    Installation guidelines 3-1 5975607 BARCODATA 808s 170397 3 INST ALLA TION GUIDELINES Installation guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to optimize the use of the projection system. Environment Do not install the projection system in a site nea ...

  • Barco R9002038 - page 11

    Installation guidelines 3-2 5975607 BARCODATA 808s 170397 Where to install the projector ? To indicate a correct installation position it is necessary to know :  The distance from projector to ceiling in case of Ceiling mounted or the distance from projector to floor in case of Table mounted;  The distance from projector to screen. To find th ...

  • Barco R9002038 - page 12

    Installation setup 4-1 5975607 BARCODATA 808s 170397 4 INST ALLA TION SETUP Removing the top cover During some installations, it will be convenient to remove the top cover from the projector totally. Proceed as follows :  Pivot the top cover backwards 90° (fully extended);  Push carefully the top cover to the left side (viewing from the rear ...

  • Barco R9002038 - page 13

    Installation setup 4-2 5975607 BARCODATA 808s 170397 Scan Adaptation The scan switches must be placed in the correct position which corresponds to the desired scanning configuration. To change the scanning, it is necessary to remove the projector top cover and to open the protection plate. For opening the projector's top cover, see 'Acces ...

  • Barco R9002038 - page 14

    Installation setup 4-3 5975607 BARCODATA 808s 170397 - Press the module lock and lift up the module handle; - Repeat this action on both sides of the module and extract the module out of the main frame. Side view Top view Top view Side view Push Connectors for the vertical deflection module Vertical scan switch Vertical Scan Switch One vertical swi ...

  • Barco R9002038 - page 15

    Installation setup 4-4 5975607 BARCODATA 808s 170397 To check the current positions of the scan switches, proceed as follows: Attention : This procedure can only be done after power (mains) connection. So, first continue with the projector setup and the connections and then return to this procedure.  Switch on the projector. The projector starts ...

  • Barco R9002038 - page 16

    Projector setup 5-1 5975607 BARCODATA 808s 170397 5 PROJECT OR SETUP StdBY MA IN POWER PROC ESSOR CY C BLOC K MATC H ERROR RCU RCV DS PC PA US E PRO J EC TO R A DDRES S (sum ) OF F ON BAUD R A T E T ABLE T O COM PUTE R POW ER UP M O DE OPER AT I N G MO D E W H EN P OW ER IS S W I TCHED ON ON OFF PLA YIN G StdBY PASSWOR D MO DE ON OFF YE S NO RE S E ...

  • Barco R9002038 - page 17

    Projector setup 5-2 5975607 BARCODATA 808s 170397 1 128 2 6 4 3 3 2 4 1 6 5 8 6 4 7 2 8 1 Setting the address is a hardware SETUP of your projector which must be done during installation. Use the 8 DIP switches provided on the controller board labelled 'Projector Address'. Each DIP switch has its own decimal value. The sum of the values a ...

  • Barco R9002038 - page 18

    Projector setup 5-3 5975607 BARCODATA 808s 170397 Position of DIP switches and baud rate codes : Baud Rate for communication with a computer The communication speed between the projector and the computer has 8 possible settings. With DIP Switch No. 6, No.7 and No.8 of the 8 DIP switches on the controller board, labelled as Baud rate code (sum)? ...

  • Barco R9002038 - page 19

    Projector setup 5-4 5975607 BARCODATA 808s 170397 ...

  • Barco R9002038 - page 20

    AC power connection 6-1 5975607 BARCODATA 808s 170397 6 AC POWER CONNECTION AC Power (mains) cord connection Use the supplied cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the back of the projector. This projector may be connected to an IT-power system. The IT- power system is a power ...

  • Barco R9002038 - page 21

    AC power connection 6-2 5975607 BARCODATA 808s 170397 AC Power check Check the power voltage which is determined by the ART. NR. (Article number) included in the label pasted on the backside of the projector. Projectors with the ART. NR. R9000901 and R9000902 must be connected to a 230 VAC power source. Projectors with the ART. NR. R9000908 and R90 ...

  • Barco R9002038 - page 22

    AC power connection 6-3 5975607 BARCODATA 808s 170397 Switching on the projector Push the power (mains) switch located on the rear panel of the projector to switch the projector ON and OFF :  If the switch is pressed in : ON  If the switch is Not pressed in : OFF The projector can be started up in the 'Operational mode' (image displ ...

  • Barco R9002038 - page 23

    AC power connection 6-4 5975607 BARCODATA 808s 170397 ...

  • Barco R9002038 - page 24

    Source connections 7-1 5975607 BARCODATA 808s 170397 4/5 Component video 8 with Tri-level sync R, G and B with composite sync on Green; 3 RGB 3 R, G and B with separate composite or with separate Horizontal and Vertical sync. Port No Projector input Numeric button Description of input signal 1 Composite Video 1 S-video : Y/C (luma/chroma). The Comp ...

  • Barco R9002038 - page 25

    Source connections 7-2 5975607 BARCODATA 808s 170397 Connecting a S-Video (or Composite Video) source to Port 2 Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals can be connected to Port 2 . The composite video can also be connected to this port. To select the S-video input : Press the numeric button 2 on the RCU or ...

  • Barco R9002038 - page 26

    Source connections 7-3 5975607 BARCODATA 808s 170397 RGB Input Auto Sync Tracking Module Procedure to remove the line termination resistors :  Turn off the projector and unplug the projector power cord.  Remove the top cover from the projector (see p.4-1).  Remove the RGB Input Auto Sync Tracking Module from the main frame.  Unsolder an ...

  • Barco R9002038 - page 27

    Source connections 7-4 5975607 BARCODATA 808s 170397 Connecting a RGB Analog source with Tri- level sync to Port 4/5 (option) RGB analog input terminals with Tri-level sync input or with Tri-level sync on green can be connected to the projector via Port 4/5. The projector detects automatically where the sync signal is located. This feature requires ...

  • Barco R9002038 - page 28

    Installation adjustment mode 8-1 5975607 BARCODATA 808s 120397 8 INST ALLA TION ADJUSTMENT MODE Before starting any adjustment. The BARCODATA 808s is factory optimized for a screen with range 1.9m (74.8 inch) to 3.2m (126.0 inch) You wish an optimal focused image for a screen width between 1.2m to 1.9m or between 3.2m and 6m? then, carry out the fo ...

  • Barco R9002038 - page 29

    Installation adjustment mode 8-2 5975607 BARCODATA 808s 120397 Adaptation procedure : 1. Open and remove the top cover LENSES Le ns nut 2. Remove the lenses by : - remove for each lens the 4 nuts, holding lens to picture tube support (nutdriver 8 mm). - remove the lens from the bolts 3. Placing the required washers : a) optimal focus in the screen ...

  • Barco R9002038 - page 30

    Installation adjustment mode 8-3 5975607 BARCODATA 808s 120397 Access to Installation Adjustment Mode It will be necessary to perform several mechanical adjustments while in the Installation Adjustment Mode. It will be required to open and remove the projector's top cover in order to gain access to the adjustment points. To enter into the inst ...

  • Barco R9002038 - page 31

    Installation adjustment mode 8-4 5975607 BARCODATA 808s 120397 Optical Lens Focusing The optical focusing procedure is performed separately for each lens. The appropriate CRT will be switched on as the user proceeds through the optical focusing adjustment sequence. Each lens has two focus adjustment points, one at the rear of the lens and one at th ...

  • Barco R9002038 - page 32

    Installation adjustment mode 8-5 5975607 BARCODATA 808s 120397 Raster Centering The raster must be centered on the CRT faceplate of each tube, therefore, it is necessary to look into the lenses. Caution : To avoid eye discomfort while performing these adjust- ments, reduce the contrast and gradually increase the brightness level until the raster be ...

  • Barco R9002038 - page 33

    Installation adjustment mode 8-6 5975607 BARCODATA 808s 120397 CRT Projection Angle Adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. NOTE : Never try to correct this misalignment wi ...

  • Barco R9002038 - page 34

    Installation adjustment mode 8-7 5975607 BARCODATA 808s 120397 Loosen bolts E, F, G and H to pivot the blue CRT until the center of the Blue image and the center of the Green image coincide. When the angle of the blue CRT is corrected, tighten the four bolts. Press the <ENTER> key to continue with the diagonal focusing menu. Press the <EXI ...

  • Barco R9002038 - page 35

    Installation adjustment mode 8-8 5975607 BARCODATA 808s 120397 ...

  • Barco R9002038 - page 36

    Messages, warnings and failure codes 9-1 5975607 BARCODATA 808s 120397 9 MESSAGES, W ARNINGS AND F AILURE CODES SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz Announcement of the selected source. enter password xxxx Message to enter your password. Password contains 4 digits. text on text off These messages will be displayed on ...

  • Barco R9002038 - page 37

    Messages, warnings and failure codes 9-2 5975607 BARCODATA 808s 120397 WARNING : go to stand by Projector will switch to 'Standby' when the RCVDS is no longer available. WARNING : invalid frequency input The entered frequency or applied frequency of the source is out of the projector's range. WARNING : default settings loaded in the ...

  • Barco R9002038 - page 38

    Appendix A: BARCO ceiling mount support A-1 5975607 BARCODATA 808s 170397 A BARCO CEILING MOUNT SUPPORT This appendix gives only an overview of the contents of the installa- tion guidelines and some overview drawings. The installation guidelines for the BARCO ceiling mounting support can be ordered from BARCO. The order number: R5975693 . Contents ...

  • Barco R9002038 - page 39

    Appendix A: BARCO ceiling mount support A-2 5975607 BARCODATA 808s 170397 Projector position corrections  Water-level adjustment D  Projector axis adjustment C ...

  • Barco R9002038 - page 40

    Appendix B: G2 adjustment B-1 5975996 BARCODATA 808s 170397 B G2 ADJUSTMENT Once the on-screen menu "G2 ADJUSTMENT" is displayed, proceed as follows : < E X IT > t o re tu rn Use the potent iometer s on the G2-ADJ. module t o set t he scr een gri d vol t age for Red, Green and B lue. Adjus t unt i l t he LED on the cor res pondi ng ...

  • Barco R9002038 - page 41

    Appendix B: G2 adjustment B-2 5975607 BARCODATA 808s 170397 ...

  • Barco R9002038 - page 42

    Gamma corrections C-1 5975607 BARCODATA 808s 170397 C GAMMA CORRECTIONS When entering the gamma corrections, a warning will be displayed : "RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR. THE GAMMA CORRECTIONS ARE FACTORY ADJUSTED USING AN ACTAS COLOR ANALYZER ! THEREFORE, ONLY QUALIFIED INSTALLATION OR SERVICE PERSONNEL SHOULD PERFORM THESE AD ...

  • Barco R9002038 - page 43

    Gamma Corrections C-2 5975607 BARCODATA 808s 170397 To carry out the Red and Blue Midlights Correction :  Push the control stick forward or backward to highlight the item R & B MIDLIGHTS in the menu and then press the <ENTER> key. If the <EXIT> key is pressed, the projector will return to the Service menu.  After the <ENTER ...

  • Barco R9002038 - page 44

    FORMULA OUTSIDE PACKAGE DIMENSIONS (Inches) CHEMICAL FAMILY FEDERAL STOCK NUMBER (FSN) GROSS WEIGHT (LBS) % TRESHOLD LIMIT VALUE (Units) ALLOYS AND METALLIC COATINGS % % PIGMENTS SOLVENTS ADDITIVES CATALYST VEHICLE HAZARDOUS MIXTURES OF OTHER LIQUIDS, SOLIDS, OR GASES APPEARANCE AND ODOR BOILING POINTS (°C.) SPECIFIC GRAVITY (H 2 O=1) VAPOR PRESSU ...

  • Barco R9002038 - page 45

    STABILITY UNSTABLE STABLE CONDITIONS TO AVOID INCOMPATABILITY (Materials to avoid) HAZARDOUS DECOMPOSITION PRODUCTS HAZARDOUS POLYMERIZATION WILL NOT OCCUR CONDITIONS TO AVOID MAY OCCUR STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED WASTE DISPOSAL METHOD RESPIRATORY PROTECTION (Specific type) VENTILATION LOCAL EXHAUST MECHANICAL (General ...

Manufacturer Barco Category Projector

Documents that we receive from a manufacturer of a Barco R9002038 can be divided into several groups. They are, among others:
- Barco technical drawings
- R9002038 manuals
- Barco product data sheets
- information booklets
- or energy labels Barco R9002038
All of them are important, but the most important information from the point of view of use of the device are in the user manual Barco R9002038.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Barco R9002038, service manual, brief instructions and user manuals Barco R9002038. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Barco R9002038.

Similar manuals

A complete manual for the device Barco R9002038, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Barco R9002038 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Barco R9002038.

A complete Barco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Barco R9002038 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Barco R9002038, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Barco R9002038, that we can find in the current document
3. Tips how to use the basic functions of the device Barco R9002038 - which should help us in our first steps of using Barco R9002038
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Barco R9002038
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Barco R9002038 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Barco R9002038?

Use the form below

If you did not solve your problem by using a manual Barco R9002038, ask a question using the form below. If a user had a similar problem with Barco R9002038 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)