English dropdown-ico

Manual Apple Drive Interconnect Board

11 pages 0.28 mb
Download

Go to site of 11

Summary
  • Apple Drive Interconnect Board - page 1

    073-0673 Re v . C  Xserve Drive Interconnect Board Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Online instructions covering customer-installab le par ts are av ailab le at http://www .info .apple.com/installpar ts/. ...

  • Apple Drive Interconnect Board - page 2

    Xserve Drive Interconnect Board - 2 4. If the ser v er is in the loc k ed position (the y ellow security LED on the front panel is on), use the Allen ke y that came with the server to unloc k it. 5. If the cable management arm is not in use, unplug all e xternal cables e xcept the power cord. 6. T ouch the ser ver’ s metal case to discharge any s ...

  • Apple Drive Interconnect Board - page 3

    Xserve Drive Interconnect Board - 3 9. Grasp the thumbscre ws and slide the bottom housing f orward part wa y to e xpose the two chassis le v ers . (Figure 2) 10. While depressing both le v ers , pull the bottom housing all the w a y forw ard and remo v e it from the rac k. Figure 2 11. Place the bottom housing on a sturdy , flat surf ace and ESD ...

  • Apple Drive Interconnect Board - page 4

    Xserve Drive Interconnect Board - 4 F or each installed drive , do the f ollowing: 1. Press the handle on the front of the drive module so the handle pops out. (Figure 3) Figure 3 2. Grasp the drive handle , and pull the drive module out of the server . (Figure 4) Figure 4 ...

  • Apple Drive Interconnect Board - page 5

    Xserve Drive Interconnect Board - 5 Blowers 1. Disconnect the cable f or the r ight blo wer from the driv e interconnect board. (Figure 5) 2. Lift the right blow er straight up off its mounting pegs and remo v e it from the ser v er . 3. Repeat steps 1 and 2 f or the left blo wer . Figure 5 ...

  • Apple Drive Interconnect Board - page 6

    Xserve Drive Interconnect Board - 6 Heatsink Duct Note: There are two versions of Xserve. If your v ersion does not include a plastic duct ov er the heatsink, skip to “A T A Controller Board” on the f ollo wing page. 1. Release the latch on the heatsink duct from its slot, slide the duct aw a y from the blo wer , and lift the end of the duct as ...

  • Apple Drive Interconnect Board - page 7

    Xserve Drive Interconnect Board - 7 A T A Controller Board 1. Press in on both ends of the clip securing the r ight side of the A T A controller board and remov e the clip from the server . Repeat f or the clip on the left side of the board. 2. Lift the A T A controller board straight up to disconnect it from the drive interconnect and logic boards ...

  • Apple Drive Interconnect Board - page 8

    Xserve Drive Interconnect Board - 8 Drive Inter connect Board 1. Disconnect the f ollowing cab les from the drive interconnect board: (Figure 8) • optical drive cable • power supply cable • locking switch cable • front panel board cable • FireWire cable Figure 8 2. Release the three thumbscrews that secure the driv e interconnect board to ...

  • Apple Drive Interconnect Board - page 9

    Xserve Drive Interconnect Board - 9 Installing the Replacement Driv e Inter connect Board 1. Install the replacement drive interconnect board on the two mounting pegs in the chassis. (Figure 10) 2. Check that the board engages with the three br ack ets on the chassis . 3. Press the board fir mly to ward the front of the server , and tighten the th ...

  • Apple Drive Interconnect Board - page 10

    Xserve Drive Interconnect Board - 10 5. Reconnect the A T A controller board to the dr iv e interconnect and logic boards. Note: When replacing the ATA controller board, align it over the two pairs of connectors on the drive interconnect and logic boards, making sure the “MLB” arrow points toward the logic board, and press down. (Figure 12) Fig ...

  • Apple Drive Interconnect Board - page 11

    Xserve Drive Interconnect Board - 11 7. If you remo v ed it earlier , replace the heatsink duct on the heatsink. 8. Reinstall the blo wers . 9. Reinstall the hard drives. Closing the Serv er 1. Carefully slide the bottom housing back into the r ack. 2. Tighten the front thumbscrews to secure it. W arning: Never turn on the server unless all of its ...

Manufacturer Apple Category Computer Hardware

Documents that we receive from a manufacturer of a Apple Drive Interconnect Board can be divided into several groups. They are, among others:
- Apple technical drawings
- Drive Interconnect Board manuals
- Apple product data sheets
- information booklets
- or energy labels Apple Drive Interconnect Board
All of them are important, but the most important information from the point of view of use of the device are in the user manual Apple Drive Interconnect Board.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Apple Drive Interconnect Board, service manual, brief instructions and user manuals Apple Drive Interconnect Board. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Apple Drive Interconnect Board.

Similar manuals

A complete manual for the device Apple Drive Interconnect Board, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Apple Drive Interconnect Board by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Apple Drive Interconnect Board.

A complete Apple manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Apple Drive Interconnect Board - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Apple Drive Interconnect Board, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Apple Drive Interconnect Board, that we can find in the current document
3. Tips how to use the basic functions of the device Apple Drive Interconnect Board - which should help us in our first steps of using Apple Drive Interconnect Board
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Apple Drive Interconnect Board
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Apple Drive Interconnect Board in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Apple Drive Interconnect Board?

Use the form below

If you did not solve your problem by using a manual Apple Drive Interconnect Board, ask a question using the form below. If a user had a similar problem with Apple Drive Interconnect Board it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)