English dropdown-ico

Manual Xerox 5335

17 pages 0.28 mb
Download

Go to site of 17

Summary
  • Xerox 5335 - page 1

    OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE MANUEL DE L'UTILISATEUR. PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL M ...

  • Xerox 5335 - page 2

    2 3 POWER TOOL USE AND CARE 16. Do not force the power tool. Use the correct power tool for your ap- plication. The correct power tool will do the job better and safer at the rate for which it was designed. 17. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be con- trolled with the switch is dangerou ...

  • Xerox 5335 - page 3

    4 5 The grounding prong in the plug is con- nected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool's ground- ing system and must never be attached to an electrically live terminal. Y our tool must be plugged into an appro- priate outlet, pr ...

  • Xerox 5335 - page 4

    6 7 W ARNING! To reduce the risk of injury, wear safety goggles or glasses with side shields. Unplug the tool before changing accessories or making adjustments. Use only specifically recommended MILWAUKEE hammer irons. Others may damage tool. OPERATION Grounded tools require a three wire ex- tension cord. Double insulated tools can use either a two ...

  • Xerox 5335 - page 5

    8 9 Trigger Trigger lock Fig. 3 St arting and Stopping the T ool 1. Pull the trigger to start the tool. 2. Release the trigger to stop the tool. Locking Trigger The lock button holds the trigger in the ON position for continuous full-speed use. Side handle knob Side handle Fig. 4 1. T o lock the trigger , hold in the lock but- ton while pulling the ...

  • Xerox 5335 - page 6

    10 11 Hammer Irons The MILWAUKEE Breaker Hammer is ideal for chipping, chiseling, and heavy-duty break- ing in many materials. A variety of hammer irons are available as shown. Bull Points This iron is ideal for general demolition work. It moves in a random pattern and effec- tively breaks the material from a corner or an edge into an open area. 12 ...

  • Xerox 5335 - page 7

    12 13 SÉCURITÉ DU LIEU DE TRAVAIL SÉCURITÉ ÉLECTRIQUE A VER TISSEMENT! LIRE SOIGNEUSEMENT TOUTES LES INSTRUCTIONS Le non respect des instructions ci-après peut entraîner des chocs électriques, des incendies et/ou des blessures graves. Le terme «outil électrique» figurant dans les avertissements ci-dessous renvoie à loutil électrique ...

  • Xerox 5335 - page 8

    14 15 Outils mis à la terre : Outils pourvus dune fiche de cordon à trois dents Les outils marqués « Mise à la terre requise » sont pourvus dun cordon à trois fils dont la fiche a trois dents. La fiche du cordon doit être branchée sur une prise correctement mise à la terre (voir Figure A). De cette façon, si une défectuosité dans ...

  • Xerox 5335 - page 9

    16 17 MANIEMENT A VER TISSEMENT! Pour minimiser les risques de blessures, portez des lunettes à coques latérales. Débranchez loutil avant de changer les accessoires ou deffectuer des réglages. Lemploi daccessoires autres que ceux qui sont expressément recommandés peut comporter des risques. Installation des pièces-outils (Fig. 1 ...

  • Xerox 5335 - page 10

    18 19 V errouillage de la détente Le bouton de verrouillage maintient la détente à la position de marche continue à plein régime. 1. Pour verrouiller la détente, appuyez sur le bouton de verrouillage et enfoncez la détente puis relâchez-la. 2. Pour déverrouiller la détente, enfoncez- la et relâchez-la. Le bouton de verrouillage va se dé ...

  • Xerox 5335 - page 11

    20 21 Outillage de percussion Le marteau de démolisseur MILWAUKEE est loutil idéal pour le décapage, le ciselage et le forage dans plusieurs genres de matériaux. Les pièces-outils disponibles sont décrites ci-dessous : Pièce pointue Cet outil est utile pour le travail général de démolition. Il attaque le matériau par mouvements asynch ...

  • Xerox 5335 - page 12

    22 23 16. No fuerce la herramienta eléctrica. Use la herramienta eléctrica correcta para la aplicación. L a herramienta eléctrica correcta funcionará mejor y de manera más segura a la velocidad para la que se diseñó. 17. No use la herramienta eléctrica si el interruptor no la enciende ni la apaga. Cualquier herramienta eléctrica que no se ...

  • Xerox 5335 - page 13

    24 25 Herramientas con conexión a tierra: Herramientas con enchufes de tres clavijas Las herramientas marcadas con la frase Se requiere conexión de puesta a tierra tienen un cable de tres hilo y enchufes de conexión de puesta a tierra de tres clavijas. El enchufe debe conectarse a un tomacorriente debidamente conectado a tierra (véase la ...

  • Xerox 5335 - page 14

    26 27 OPERACION Para reducir el riesgo de una lesión, use siempre lentes de seguridad o anteojos con protectores laterales. Desconecte la herramienta antes de cambiar algún accesorio o de hacerle algún ajuste. Utilice solamente los accesorios recomendados específicamente. Otros tipos pueden ser arriesgados. ¡ADVERTENCIA! La broca de martilleo ...

  • Xerox 5335 - page 15

    28 29 1. Para cerrar el gatillo, presione el botón de cierre mientras apriete el gatillo. Luego, suelte el gatillo. 2. Para desbloquear el gatillo, apriete el gatillo y suéltelo. El botón de cierre será soltado. Ajuste del mango lateral (Fig. 4) El modelo 5335 tiene un mango lateral que se puede ajustar a cualquier posición a los 360° alreded ...

  • Xerox 5335 - page 16

    30 31 Brocas de martilleo El martillo perforador de MILWAUKEE es ideal para astillar , cincelar y fragmentar muchos tipos de materiales. Muchos tipos de brocas están disponible como se muestra a continuación. Broca de punta Esta broca de martilleo es ideal para el trabajo de demolición general. Se mueve en un patrón aleatorio y fragmenta el ma- ...

  • Xerox 5335 - page 17

    MILWAUKEE ELECTRIC TOOL CORPORATION 13135 West Lisbon Road  Brookfield, Wisconsin, U.S.A. 53005 58-14-5335d6 10/04 Printed in Germany UNITED ST A TES - MIL W AUKEE Service MILWAUKEE prides itself in producing a premium quality product that is N OTHING B UT H EA VY D UTY ® . Y our satisfaction with our products is very import ant to us! If you e ...

Manufacturer Xerox Category Saw

Documents that we receive from a manufacturer of a Xerox 5335 can be divided into several groups. They are, among others:
- Xerox technical drawings
- 5335 manuals
- Xerox product data sheets
- information booklets
- or energy labels Xerox 5335
All of them are important, but the most important information from the point of view of use of the device are in the user manual Xerox 5335.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Xerox 5335, service manual, brief instructions and user manuals Xerox 5335. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Xerox 5335.

Similar manuals

A complete manual for the device Xerox 5335, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Xerox 5335 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Xerox 5335.

A complete Xerox manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Xerox 5335 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Xerox 5335, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Xerox 5335, that we can find in the current document
3. Tips how to use the basic functions of the device Xerox 5335 - which should help us in our first steps of using Xerox 5335
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Xerox 5335
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Xerox 5335 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Xerox 5335?

Use the form below

If you did not solve your problem by using a manual Xerox 5335, ask a question using the form below. If a user had a similar problem with Xerox 5335 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)