English dropdown-ico

Manual Directed Electronics 20.7

52 pages 8.77 mb
Download

Go to site of 52

Summary
  • Directed Electronics 20.7 - page 1

    Responder LC Model 20.7 Remote Start Keyless Entr y Owner’ s Guide © 2008 Directed Electronics, Vista, CA G4702X 2008-08 ...

  • Directed Electronics 20.7 - page 2

    ...

  • Directed Electronics 20.7 - page 3

    Contents Government regulations .....................................................................................4 W arning! Safety first .........................................................................................5 What’ s included ................................................................................................8 ...

  • Directed Electronics 20.7 - page 4

    4 © 2008 Directed Electronics. All rights reserved. Government regulations This device complies with Par t 15 of FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including inter ference that may cause undesirable operati ...

  • Directed Electronics 20.7 - page 5

    5 © 2008 Directed Electronics. All rights reserved. Control Center T o satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm or more from the person’ s body , except for the hand and wrists, to satisfy RF exposure compliance. This device complies with the Industr y Canada Radio S ...

  • Directed Electronics 20.7 - page 6

    6 © 2008 Directed Electronics. All rights reserved. W ar ning! Safety first The following safety warnings must be obser ved at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer . When properly installed, this system can start the vehicle via a command signal from ...

  • Directed Electronics 20.7 - page 7

    7 © 2008 Directed Electronics. All rights reserved. cy brake properly functions. Failure to do so can result in personal injury or prop- erty damage. W e recommend the owner have the parking / emergency brake system inspected and adjusted by a qualified automotive shop bi-annually . Use of this product in a manner contrar y to its intended mode o ...

  • Directed Electronics 20.7 - page 8

    8 © 2008 Directed Electronics. All rights reserved. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. ...

  • Directed Electronics 20.7 - page 9

    9 © 2008 Directed Electronics. All rights reserved. What’ s included One ve-button/2-way Supercode Responder LC Remote Control • One ve-button/1-way Supercode companion remote • The control module • Control center with integrated status LED and V alet override switch • A remote start defeat toggle switch • Window decals • Y our ...

  • Directed Electronics 20.7 - page 10

    10 © 2008 Directed Electronics. All rights reserved. ➤ Out of range notification If a command is issued from the remote, but the remote is beyond the range of the vehicle to receive the command, the remote will respond with an out-of range notification. If this occurs, the out-of-range icon displays on the LCD and the remote emits an error ton ...

  • Directed Electronics 20.7 - page 11

    11 © 2008 Directed Electronics. All rights reserved. outline stops flashing and the remote becomes operational while still displaying CHARGE. Sa tm ode, bank selector AUDIO PWR 12 RE WF F PL AY /PROG NR 34 56 DISC- DISC+ 11:53 XM1-1 CH-001 CH VOL SCAN SOUND AM/FM CD/AUX SA T RADIO SEEK SKIP RPT DISP - MODE A.SEL RDM TUNE AU TO OFF DUAL A/C MODE C ...

  • Directed Electronics 20.7 - page 12

    12 © 2008 Directed Electronics. All rights reserved. ➤ Multi-car control capability Y ou can use the Responder LC 2-way remote control system for two cars, with full command capability for both vehicles. T o change the car to be operated: Press/hold the 1. A U X button for 3 seconds or until the remote beeps. The car  ALL or  ALL ashes. ...

  • Directed Electronics 20.7 - page 13

    13 © 2008 Directed Electronics. All rights reserved. Responder LC 2-way  5319 ,&$ )&&,'(=6'(,  531; ,&$ )&&, ...

  • Directed Electronics 20.7 - page 14

    14 © 2008 Directed Electronics. All rights reserved. ➤ LC 1-way companion 10  5313 ,&$ )&&,'(=6'(, %$77( 5< &5 A U X  531; ,& ...

  • Directed Electronics 20.7 - page 15

    15 © 2008 Directed Electronics. All rights reserved. Using the system Please note the screen shot to the right of a feature indicates what the display looks like when this feature is activated. A U X Lock Command : Press one time to Lock Feedback : Lock Icon appears, and parking lights flash once. Notes : Press/hold for 1.5 seconds to Lock the sy ...

  • Directed Electronics 20.7 - page 16

    16 © 2008 Directed Electronics. All rights reserved. A U X Unlock Command : Press one time to Unlock Feedback : Unlock icon appears. Notes : The vehicle horn, honks two-times and the parking lights flash two-times. The door locks (if connected) unlock, the 2-way remote beeps two-times and the LCD displays the A U X icon. Unlocking without the hon ...

  • Directed Electronics 20.7 - page 17

    17 © 2008 Directed Electronics. All rights reserved. Points to remember : If the hood is open or if the brake pedal is pressed, the vehicle will not remote start. The remote start shuts down: When the brake pedal is pressed. • The hood is opened. • When the remote start command is sent again from a remote control. • When the runtime expires. ...

  • Directed Electronics 20.7 - page 18

    18 © 2008 Directed Electronics. All rights reserved. A U X Aux Command : Press and hold for 1.5 seconds to acti- vate the T runk Release. Feedback : The trunk icon appears and the remote plays a short tone. Notes : This is an optional feature. See your sales rep/installer for details. The factor y default screen displays the trunk icon and text. T ...

  • Directed Electronics 20.7 - page 19

    19 © 2008 Directed Electronics. All rights reserved. V alet mode Command: Press A U X two-times and then A U X . Feedback: Unlock icon appears hollow , "V alet" dis - plays in the text area when entering V alet mode. Notes: If the system is already locked the remote beeps one time when entering V alet mode. When exiting V alet mode the u ...

  • Directed Electronics 20.7 - page 20

    20 © 2008 Directed Electronics. All rights reserved. Car finder Command : Press A U X three-times and then A U X . Feedback : Remote beeps 1 short beep, the vehicle emits 1 long hor n honk (if connected), and the parking lights flash 10 times. Notes : Lock/Unlock cancels the light ashes. Cabin temperature Command : Press A U X one time, then H ...

  • Directed Electronics 20.7 - page 21

    21 © 2008 Directed Electronics. All rights reserved. Command : Press A U X one- time and then press A U X . Feedback : Screen changes to unlock icon Notes : Unlocks the system without chirps ➤ Overriding the optional starter kill T o bypass the optional star ter kill without a remote control: Use your override switch located on the control cente ...

  • Directed Electronics 20.7 - page 22

    22 © 2008 Directed Electronics. All rights reserved. Additional remote star t features Manual transmission If the vehicle has manual transmission the proper steps must be followed before leaving the parked vehicle or the remote start feature is disabled. Make sure the engine is running and the doors are closed. 1. Put the transmission in neutral. ...

  • Directed Electronics 20.7 - page 23

    23 © 2008 Directed Electronics. All rights reserved. Note: T o enable V alet take-over with a manual transmission, open the door and enter into manual transmission mode, as described above. The parking lights ash one-time when entering V alet take-over . Once you exit the vehicle you can lock the system and the car will remain running. If the v ...

  • Directed Electronics 20.7 - page 24

    24 © 2008 Directed Electronics. All rights reserved. Timer Mode is exited automatically after the sixth run cycle. The parking lights slowly ash 4 times when exiting timer mode. Note: The Bitwriter® can change the amount of times the remote start activates and, it can change the inter vals between activations in timer mode. T urbo Timer mode T ...

  • Directed Electronics 20.7 - page 25

    25 © 2008 Directed Electronics. All rights reserved. T o activate turbo timer mode with a manual transmission: Enter MTS mode with the door open. 1. T ransmit the timer mode feature with the remote by pressing 2. A U X two-times, and then A U X . After exiting the vehicle, lock the system and the vehicle remains running for 3. the programmed runti ...

  • Directed Electronics 20.7 - page 26

    26 © 2008 Directed Electronics. All rights reserved. Runtime check Command : While the remote start is running, press A U X two-times, and then Hold for 1.5 seconds. Feedback : T ext reads runtime and displays time left Notes : This feature is only available on the 2way remote. Runtime reset Command : While the remote star t is running, press A U ...

  • Directed Electronics 20.7 - page 27

    27 © 2008 Directed Electronics. All rights reserved. Smart star t Command : Press A U X three-times and then press A U X . Feedback : The parking lights flash 5 times fast and 'Smar t Star t On" dis- plays in the text area. Notes : Enables or disables the Smar tStart feature. The smar t star t fea- ture of this system will allow you to ...

  • Directed Electronics 20.7 - page 28

    28 © 2008 Directed Electronics. All rights reserved. The Smart Start function works similar to the T imer mode. The system must be in the locked mode. Using the system default settings, it has a maximum of 6 starting cycles ,and checks the voltage/cabin temperature every 3 hours to see if the thresholds have been met. If thresholds have been met t ...

  • Directed Electronics 20.7 - page 29

    29 © 2008 Directed Electronics. All rights reserved. Auxiliar y features Aux 1 Command : Press A U X one time and then press A U X . Feedback : T ext displays the item activated. Notes : This is an optional feature. See your sales rep/installer for details. Aux 2 Command : Press A U X two times and then press A U X . Feedback : T ext display . the ...

  • Directed Electronics 20.7 - page 30

    30 © 2008 Directed Electronics. All rights reserved. Remote control feature programming The Responder LC 2-way remote control has menus for configuring the remote control user features and for programming the remote to the system control mod - ule. Before you start make sure the keypad is unlocked. (See page 12) T o program the remote user featur ...

  • Directed Electronics 20.7 - page 31

    31 © 2008 Directed Electronics. All rights reserved. ➤ Remote setup options Feature Opt 1 Opt 2 Opt 3 Opt 4 Opt 5 Auto keypad lock On Off Back Page On Off Power save Back Page aler t Vibe T one Both Screen only Back R e m o t e s t a r t display Clock T emp Runtime Back Low runtime alert On Off Back Car 2 On Off Home Back Back light color Off 1- ...

  • Directed Electronics 20.7 - page 32

    32 © 2008 Directed Electronics. All rights reserved. ➤ Menu option descriptions Auto keypad lock • Automatically locks the remote buttons when the buttons are not used for 60 seconds. Prevents “accidental” presses of the remote. Press A U X then A U X to unlock the keypad. Note : If the auto keypad lock feature is programmed On, the remote ...

  • Directed Electronics 20.7 - page 33

    33 © 2008 Directed Electronics. All rights reserved. Low Runtime Alert • The remote reports with one shor t beep followed by 1 short error tone (repeated twice) and the text area displays "run time" when the remote start runtime is at the 3-minutes remaining. The remote beeps one more time when 1 minute is remaining. Y ou have the opti ...

  • Directed Electronics 20.7 - page 34

    34 © 2008 Directed Electronics. All rights reserved. ➤ Pair remote mode It is recommended that this feature for programming the remote to the system is performed by your installer . ➤ Demo modes One-time with sound • The LCD icons display one at a time with icon name displayed in the text field, while the remote is playing tones. One-time w ...

  • Directed Electronics 20.7 - page 35

    35 © 2008 Directed Electronics. All rights reserved. Safety features This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components. ➤ Optional starter anti-grind circuitr y Whenever the vehicle is remote started, advanced anti-grind circuitr y prevents the ...

  • Directed Electronics 20.7 - page 36

    36 © 2008 Directed Electronics. All rights reserved. Diagnostics The microprocessor at the hear t of the system is constantly monitoring the switch- es that are connected to the main unit. ➤ Locking If the system is locked at the same time that the door is active, you will hear one horn honk to indicate locking and a second horn honk to indicate ...

  • Directed Electronics 20.7 - page 37

    37 © 2008 Directed Electronics. All rights reserved. ➤ Remote start This system can provide you with infor mation to indicate what the problem is when using the remote start. When the remote start is activated and fails to engage, count the parking light flashes to determine the problem. The parking lights will flash between 5 - 8 times to ind ...

  • Directed Electronics 20.7 - page 38

    38 © 2008 Directed Electronics. All rights reserved. Owner recognition Owner recognition lets up to four users of the system have unique settings that meet their specific needs. It is almost like having four separate systems in your vehicle, one for each user . This feature is only available to authorized dealers using the Bitwriter or Bitwriter ...

  • Directed Electronics 20.7 - page 39

    39 © 2008 Directed Electronics. All rights reserved. ➤ 2-way remote Y our Responder LC 2way remote control has a feature called remote power save mode. When programmed On under remote options, the remote conserves power by disabling the paging function if unused for more than 72 hours. Pressing any button on the remote restores the paging functi ...

  • Directed Electronics 20.7 - page 40

    40 © 2008 Directed Electronics. All rights reserved. dows after remote locking. Note: Comfort closure can only be used on cars that have the capability of closing the windows (and on some cars the sunroof as well) with the key cylinder in the door . Convenience expansions Listed below are some of the expansion options available. Please consult you ...

  • Directed Electronics 20.7 - page 41

    41 © 2008 Directed Electronics. All rights reserved. Glossar y of terms 2-W ay Remote: A hand-held, remote control which operates the various func- tions of your system and receives feedback and pages from the system. Control Center: The control center contains the system’ s radio-frequency antenna, the valet and override switch, and the Status ...

  • Directed Electronics 20.7 - page 42

    42 © 2008 Directed Electronics. All rights reserved. LCD Iayout  ALL  ALL  ALL ALL ALL  ALL  ALL A L L A L L ALL ALL ➤ LCD remote features 1  ALL Lock 9  ALL Thermometer/Smart star t 2  ALL Locked in valet 10  ALL Batter y Status 3  ALL Unlock 11  ALL Hood (T rigger)* 4  ALL Unlocked in valet 12  ALL Hood ( ...

  • Directed Electronics 20.7 - page 43

    43 © 2008 Directed Electronics. All rights reserved. 17  ALL Vibe On 27  ALL Car Door 18  ALL Pager T one On 28  ALL Home (Garage - Open)** 19  ALL Siren* 29  ALL Home (Garage Close)** 20  ALL Silent Mode 2* 30  ALL Car 1 21  ALL T ransmit 31  ALL Car 2 22  ALL Receive 32  ALL All Zones* 23  ALL Out of Range ...

  • Directed Electronics 20.7 - page 44

    44 © 2008 Directed Electronics. All rights reserved. ...

  • Directed Electronics 20.7 - page 45

    45 © 2008 Directed Electronics. All rights reserved. Quick reference guide ➤ • Locking T o lock, press the A U X button . The remote beeps one-time and the LCD displays "locked" ➤ • Unlocking T o unlock press the A U X button. The remote beeps two-times and the LCD displays "unlock". ➤ • Bypassing the optional start ...

  • Directed Electronics 20.7 - page 46

    46 © 2008 Directed Electronics. All rights reserved. ➤ Rear Defogger Press A U X four-times, and then press A U X (only after remote star t is On.) The remote beeps one-time. ➤ • T o disable the remote star t system Move the shutdown toggle switch to the Off position. Location of Shutdown T oggle Switch___________________ ➤ • V alet Mode ...

  • Directed Electronics 20.7 - page 47

    47 © 2008 Directed Electronics. All rights reserved. Limited lifetime consumer warranty Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at Directed’ s election) with a comparable reconditioned model any Directed unit (hereafter the “unit”), excluding without limitation the siren, the remote tra ...

  • Directed Electronics 20.7 - page 48

    48 © 2008 Directed Electronics. All rights reserved. WITHOUT LIMIT A TION, LIABILITY FOR THEFT , DAMAGE AND/OR V ANDALISM. THIS W ARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOV AL OR REINST ALLA TION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOL VING DIRECTED OR ITS SUBSIDIARY , THE VEN ...

  • Directed Electronics 20.7 - page 49

    ...

  • Directed Electronics 20.7 - page 50

    ...

  • Directed Electronics 20.7 - page 51

    ...

  • Directed Electronics 20.7 - page 52

    G4702X 2008-08 Vista, CA 92081 www .directed.com © 2008 Directed Electronics—All rights reser ved The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 1 ...

Manufacturer Directed Electronics Category Automobile Electronics

Documents that we receive from a manufacturer of a Directed Electronics 20.7 can be divided into several groups. They are, among others:
- Directed Electronics technical drawings
- 20.7 manuals
- Directed Electronics product data sheets
- information booklets
- or energy labels Directed Electronics 20.7
All of them are important, but the most important information from the point of view of use of the device are in the user manual Directed Electronics 20.7.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Directed Electronics 20.7, service manual, brief instructions and user manuals Directed Electronics 20.7. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Directed Electronics 20.7.

Similar manuals

A complete manual for the device Directed Electronics 20.7, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Directed Electronics 20.7 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Directed Electronics 20.7.

A complete Directed Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Directed Electronics 20.7 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Directed Electronics 20.7, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Directed Electronics 20.7, that we can find in the current document
3. Tips how to use the basic functions of the device Directed Electronics 20.7 - which should help us in our first steps of using Directed Electronics 20.7
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Directed Electronics 20.7
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Directed Electronics 20.7 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Directed Electronics 20.7?

Use the form below

If you did not solve your problem by using a manual Directed Electronics 20.7, ask a question using the form below. If a user had a similar problem with Directed Electronics 20.7 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (1)

louise nadeau

code support 5011