Русский dropdown-ico

Инструкция обслуживания Nortel Mediant TP-1610 SIP

280 страниц 4.66 mb
Скачать

Перейти на страницу of 280

Summary
  • Nortel Mediant TP-1610 SIP - page 1

    Mediant™ 2000 & TP-1610 SIP User’s Manual Version 4.4 Document #: LTRT-72504 ...

  • Nortel Mediant TP-1610 SIP - page 2

    Notice This document describes the Audio Codes Mediant™ 2000 SIP (Session Initialization Protocol) gateway and the TP-1610 SIP cPCI board. Information contained in this document is believed to be accurate and reliabl e at the time of printing. However, due to ongoin g product improvem ents and revisions, AudioCodes cannot guarante e accuracy of p ...

  • Nortel Mediant TP-1610 SIP - page 3

    Mediant 2000 SIP User’s Manual Contents Version 4.4 3 July 2005 Table of Contents 1 Overview ..................................................................................................................... 13 1.1 Available Conf igurat ions ....................................................................................................... ...

  • Nortel Mediant TP-1610 SIP - page 4

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 4 Document #: LTRT-72504 5.8.3.2 Numbering Plans and Type of Nu mber ...................................................................................... 48 5.8.4 Configuring the Ro uting Tables ...........................................................................................49 5.8.4.1 T ...

  • Nortel Mediant TP-1610 SIP - page 5

    Mediant 2000 SIP User’s Manual Contents Version 4.4 5 July 2005 8.4 Using IS DN NF AS ................................................................................................................ ........141 8.4.1 NFAS Interface ID .............................................................................................................1 41 ...

  • Nortel Mediant TP-1610 SIP - page 6

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 6 Document #: LTRT-72504 11.6.4.2 Configurati on via SNMP ......................................................................................................... .. 181 11.7 SNMP Manager Backwa rd Compat ibility...................................................................................... ...

  • Nortel Mediant TP-1610 SIP - page 7

    Mediant 2000 SIP User’s Manual Contents Version 4.4 7 July 2005 Appendix J SS7 Tunnelin g ........................................................................................... 231 J.1 MTP2 Tunneli ng Technol ogy ...................................................................................................... ..232 J.2 SS7 Characteristi ...

  • Nortel Mediant TP-1610 SIP - page 8

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 8 Document #: LTRT-72504 List of Figures Figure 1-1: Typical Mediant 2000 Gateway Application .................................................................................. .14 Figure 2-1: Mediant 20 00 Front View .................................................................................. ...

  • Nortel Mediant TP-1610 SIP - page 9

    Mediant 2000 SIP User’s Manual Contents Version 4.4 9 July 2005 Figure 8-3: SIP Call Fl ow Exam ple..................................................................................................... ............ 153 Figure 5-2: IP to Trunk Gr oup Routi ng Table .................................................................................... ...

  • Nortel Mediant TP-1610 SIP - page 10

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 10 Document #: LTRT-72504 List of Tables Table 2-1: Mediant 2000 Front View Component De scriptio ns ........................................................................19 Table 2-2: Chassis LE D Indicators ......................................................................................... ...

  • Nortel Mediant TP-1610 SIP - page 11

    Mediant 2000 SIP User’s Manual Contents Version 4.4 11 July 2005 Table K-5: VoiceXML Supported Pr operties ....................................................................................... ...........260 Table L-1: acBoardFat alError Alarm Trap ........................................................................................ ........ ...

  • Nortel Mediant TP-1610 SIP - page 12

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 12 Document #: LTRT-72504 Tip: When viewing this manual on CD, Web site or on any other electronic copy, all cross-references are h yperlinked. Click on the p age or section num bers (shown in blue) to reach the individual cross-referenced item directly. To return back to the point from where you ac ...

  • Nortel Mediant TP-1610 SIP - page 13

    Mediant 2000 SIP User’s Manual 1. Overview Version 4.4 13 July 2005 1 Overview The Mediant 2000 SIP Voice over IP ( VoIP) gateway enables voice, fax, and data traffic to be sent over the same IP network. The Medi ant 2000 pr ovides ex cellent voice quality and optimized packet voice streaming over IP networks. The Mediant 2000 uses the award-winn ...

  • Nortel Mediant TP-1610 SIP - page 14

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 14 Document #: LTRT-72504 Figure 1-1 below illustrates typical Mediant 2000 gate way applications over VoIP Network. Figure 1-1: T ypical Mediant 2000 Gateway Application SI P Se r v i c e N ode LAN PST N LAN T e le phone LAN SIP Pr o xy M e d ian t 2000 E 1 /T1 P R I/CAS Ro u t e r M e d ian t 2000 ...

  • Nortel Mediant TP-1610 SIP - page 15

    Mediant 2000 SIP User’s Manual 1. Overview Version 4.4 15 July 2005 • 48 Channels on 2 T1 spans with gate way-1 only • 96 Channels on 4 T1 spans with gate way-1 only • 192 Channels on 8 T1 spans with g ateway-1 only • 384 Channels on 16 T1 spans with gateway-1 and gateway-2 1.2 SIP Overview SIP is an application-layer control (signaling ) ...

  • Nortel Mediant TP-1610 SIP - page 16

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 16 Document #: LTRT-72504 1.3.3 PSTN-to-SIP Interworking The Mediant 2000 gateway performs int erworking between ISDN and CAS via E1/T1/J1 digital spans and SIP IETF signaling protocol. 16 E1, T1 or J1 spans are supported (480 ch annels) in a two modules gateway. The Mediant 2000 gateway supports va ...

  • Nortel Mediant TP-1610 SIP - page 17

    Mediant 2000 SIP User’s Manual 1. Overview Version 4.4 17 July 2005 • Works with Proxy or without Proxy, using an internal routing table. • Fallback to internal routing table if Proxy is not responding. • Supports up to four Proxy server s. If the primary Proxy fails, the Mediant 2000 automatically switches to a redundant Proxy. • Support ...

  • Nortel Mediant TP-1610 SIP - page 18

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 18 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 19

    Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 19 July 2005 2 Mediant 2000 Physical Description This section provides detailed inform ation on the Mediant 2000 h ardware compon ents, the location and functionality of the LEDs, buttons and connecto rs on the front and rear panels. 2.1 General The Mediant 2000 gatew ...

  • Nortel Mediant TP-1610 SIP - page 20

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 20 Document #: LTRT-72504 2.2 The Mediant 2000 Chassis The Mediant 2000 chassis is an ind ustrial platform, 19” wide, 1U high and 1 2” deep that houses the TP-1610 board in its front cage , slot #1 (the lower slot) and the TP-161 0 RTM in its rear cage, slot #1 (the lower slot). Slot # 2 in the ...

  • Nortel Mediant TP-1610 SIP - page 21

    Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 21 July 2005 Figure 2-2: F ront and Upper Vie w of the TP-1610 cPCI Board Table 2-3: Fr ont and Upper View of the TP-1610 cP CI Board Component Descriptions Item # Label Component Description 1 Status LEDs 2 ETH Ethernet LEDs 3 Reset button 4 cPCI LEDs 5 cPCI Latch 6 ...

  • Nortel Mediant TP-1610 SIP - page 22

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 22 Document #: LTRT-72504 Note 1: Before removing or inserting boa rds from / to the chassis, attach a wrist strap for electrostatic discharge (ESD) and connect it to the rack fram e using an alligator clip. Note 2: Do not set components down without protecting them with a static bag. 2.3.1.1 Removi ...

  • Nortel Mediant TP-1610 SIP - page 23

    Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 23 July 2005 2.3.2 TP-1610 Front Panel LED Indicators The functionality of the front panel LEDs for the TP-1610 is described in the following four ta bles and illustrated in Figure 2-2 on page 21 . Note that there is a choice of front panels according to the number of ...

  • Nortel Mediant TP-1610 SIP - page 24

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 24 Document #: LTRT-72504 2.4 Rear Transition Module The Mediant 2000 RTM includes a PST N trunks and an Ethernet interfaces. The Ethernet interface features dual 1 0/100 Base-TX, RJ-45 shielded connect ors for (an active / standby) redundancy sche me providing prot ection against the event of a fai ...

  • Nortel Mediant TP-1610 SIP - page 25

    Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 25 July 2005 Figure 2-4: Rear Panel with 8 RJ-48c Connectors for 8 Trunks Table 2-9: Rear Panel with 8 RJ-48c Connect ors for 8 Trunks Component Descriptio ns Item # Label Component Description 1 ETHERNET 2 Ethernet Ports. 2 RJ-45 network conne ctors 2 TRUNKS 8 E1/T-1 ...

  • Nortel Mediant TP-1610 SIP - page 26

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 26 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 27

    Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 27 July 2005 3 Installing the Mediant 2000 This section describe s the hardware installation procedures fo r the Mediant 2000. For information on how to start using the gateway, refer to Section 4 on page 35 . For detailed information on the Mediant 2000 connectors, LEDs an ...

  • Nortel Mediant TP-1610 SIP - page 28

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 28 Document #: LTRT-72504 Figure 3-1: 19-inch Rack & Desktop Accessories 3.3 Mounting the Mediant 2000 The Mediant 2000 can be mounted on a desktop, or installe d in a standard 19-inch rack. Ref er to Section 3.4 on page 30 for cabling the Mediant 2000. 3.3.1 Mounting the Mediant 2000 on a Deskt ...

  • Nortel Mediant TP-1610 SIP - page 29

    Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 29 July 2005 Figure 3-2: Mediant 2000 Front Vie w with 19-inch Rack Mount Brackets Rack Mount Safety Instructions (UL) When installing the cha ssis in a rack, be sure to implement the following Safety instructions recommended by Underwriters L aboratories: • Elevated Oper ...

  • Nortel Mediant TP-1610 SIP - page 30

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 30 Document #: LTRT-72504 2. You’re now recommended to take the optional steps of fastening the device to the frame of the rack (as described above) while it is pl aced on the shelf, so preventing it from sliding when inserting cables into con nectors on the rear panel. 3.4 Cabling the Mediant 200 ...

  • Nortel Mediant TP-1610 SIP - page 31

    Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 31 July 2005 Figure 3-4: Mediant 2000 Rear Panel Cabling (8 Trunks, DC Po wer)) Table 3-2: Mediant 2000 Rear Panel Cabling (8 Trunks, DC Power) Compo nent Descriptions Item # Label Component Description 1 RTM latches. 2 ETH A Category 5 network cable, conn ected to the Ethe ...

  • Nortel Mediant TP-1610 SIP - page 32

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 32 Document #: LTRT-72504 3. Repeat steps 1 and 2 for the other Trunk cable but this time connect it to the connector labeled “Trunks 9  16”. The 50-pin male Telco cable connector must be wired accordi ng to the pinout in Table 3-3 be low, and to mate with the female connector illustrate d in ...

  • Nortel Mediant TP-1610 SIP - page 33

    Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 33 July 2005 Figure 3-7: Pinout of RJ-45 Connector s 1 2 3 4 5 6 7 8 RJ-45 LAN Connect or and Pi nout 4, 5, 7, 8 not connected 1 = Tx+ 2 = Tx- 3 = Rx+ 6 = Rx- 3.4.3 Connecting the Power Supply Connect the Mediant 2000 to the power sup ply using one of the following methods: ...

  • Nortel Mediant TP-1610 SIP - page 34

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 34 Document #: LTRT-72504 Figure 3-8: DC Terminal Block Screw Connector  When using a DC terminal block cr imp connector, take these 3 steps: 1. Remove the DC adaptor (screw connection type) that is attached to the Mediant 2000 rear panel. 2. Connect the two ins ulated wires to the correct DC pow ...

  • Nortel Mediant TP-1610 SIP - page 35

    Mediant 2000 SIP User’s Manual 4. Getting Started Version 4.4 35 July 2005 4 Getting Started The Mediant 2000 is supplied with application softwar e already re sident in its flash memory (wit h factory default parameters). Section 4.1 below describes how to assign IP addres ses to the Mediant 2000, while Section 4.1.2 on page 35 describes how to ...

  • Nortel Mediant TP-1610 SIP - page 36

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 36 Document #: LTRT-72504 correspond with your network IP settings. If your network doesn’t feature a default gateway, enter a dummy value in the ‘Default Gateway IP Address’ field. 5. Click the Reset button and click OK in the prompt; The Mediant 2000 applies the changes and restarts. This ta ...

  • Nortel Mediant TP-1610 SIP - page 37

    Mediant 2000 SIP User’s Manual 4. Getting Started Version 4.4 37 July 2005 This option is currently supported on one media gateway module (trunks 1 -8) only.  To restore networking parameters to their initial state, take these 6 steps: 1. Disconnect the Mediant 2000 from the power and network cables. 2. Reconnect the power cable; the gateway i ...

  • Nortel Mediant TP-1610 SIP - page 38

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 38 Document #: LTRT-72504  Enable the DMZ (Demilitarized Zone ) configuratio n on the resi dential router for the LAN port where the Mediant 2000 gateway is conn ected. This enable s unknown packets to be routed to the DMZ port. 2. Under ‘SIP Parameters’, enter the Mediant 2000 domain name in ...

  • Nortel Mediant TP-1610 SIP - page 39

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 39 July 2005 5 Web Management 5.1 Configuration Concepts Users can utilize the Mediant 2000 in a wide vari ety of applications, enabled by its param eters and configuration files (e.g., Call Progres s Tones (CPT), etc.). The param eters can be configur ed and configuration files can be ...

  • Nortel Mediant TP-1610 SIP - page 40

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 40 Document #: LTRT-72504 5.4 Password Control The Embedded Web Server is p rotected by a unique username and pa ssword combination. The first time a browser request i s made, the User is reque sted to provide his use rname and password to obtain access. Subsequent reque sts are negotiated by the br ...

  • Nortel Mediant TP-1610 SIP - page 41

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 41 July 2005 5.6 Accessing the Embedded Web Server  To access the Embedded Web Server, take these 4 steps: 1. Open a standard Web-browsing applica tion such as Microsoft™ Internet Explorer™ (Version 6.0 and higher) or Netscape™ Navig ator™ (Version 7.0 and higher). 2. In the ...

  • Nortel Mediant TP-1610 SIP - page 42

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 42 Document #: LTRT-72504 5.7 Getting Acquainted with the Web Interface Figure 5-2 shows the general layout of the We b Interface screen. Figure 5-2: Mediant 2000 Web Interface The Web Interface screen features the following components: • Title bar - contains three configurable elements : corporat ...

  • Nortel Mediant TP-1610 SIP - page 43

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 43 July 2005 • Advanced Configuration – Use this menu to set the gateway’s advanced configuration parameters (for advance d users only) (refer to Section 5.9 on page 62 ). • Status & Diagnostics – Use thi s menu to view and monitor the gateway’s channels, Syslo g message ...

  • Nortel Mediant TP-1610 SIP - page 44

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 44 Document #: LTRT-72504 5.8 Protocol Management Use this menu to configure the gateway’s SIP parameters an d tables. 5.8.1 Protocol Definition Parameters Use this submenu to configure the following ga teway’s specifi c SIP protocol parameters: • General Parameters • Proxy & Registratio ...

  • Nortel Mediant TP-1610 SIP - page 45

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 45 July 2005 5.8.2 Advanced Parameters Use this submenu to configure the following gateway’s advance d control protocol parameters. • Disconnect and Answer Supervision • CDR and Debug • Miscellaneous Parameters • Supplementary Services 5.8.3 Number Manipulation Tables The VoIP ...

  • Nortel Mediant TP-1610 SIP - page 46

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 46 Document #: LTRT-72504 Figure 5-4: Source Phone Number Manipulation T able for Tel  IP Calls 2. In the ‘Table Index’ drop-down list, select the r ange of entries that you want to edit (up to 20 entries can be configured for Source Number Manipulation and 50 entries for Destination Number M ...

  • Nortel Mediant TP-1610 SIP - page 47

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 47 July 2005 Table 5-1: Number Manipulation Parameters Parameter Description Prefix / Suffix to add • Prefix - Enter the number / string you want to add to the front of the phone number. For example, if you enter 9 and the phone number is 123 4, the new number is 91234. • Suffix - E ...

  • Nortel Mediant TP-1610 SIP - page 48

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 48 Document #: LTRT-72504 • [2,3,4]xxx# represents four-digit numbers that start with 2, 3 or 4 • 54324 represents any number that sta rts with 54324 • 54324xx# represents a 7 digit number that starts with 54324 • 123[100-200]# repre sents all numbers from 123100 to 12320 0. The VoIP gateway ...

  • Nortel Mediant TP-1610 SIP - page 49

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 49 July 2005 5.8.4 Configuring the Routing Tables Use this submenu to configure the ga teway’s IP  Tel and Tel  IP routing tables and their associated parameters. 5.8.4.1 Tel to IP Routing Table The Tel to IP Routing Table is used to route incomi ng Tel call s to IP addresses. T ...

  • Nortel Mediant TP-1610 SIP - page 50

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 50 Document #: LTRT-72504 Alternative Routing’ table, the gateway imme di ately initiates a call to the redund ant destination using the next matched entry in the ‘Tel to IP Routing’ table. Note th at if a domain name in this table is resolved to two IP addresse s, the timeout for Invite retra ...

  • Nortel Mediant TP-1610 SIP - page 51

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 51 July 2005 Table 5-3: Tel to IP Routing Table Parameter Description Any telephone number whose destination number matches the prefix defin ed in the ‘Desti nation Phone Prefix’ field and its source number matches the prefix defined in the adjace nt ‘Source Phone Prefix‘ field, ...

  • Nortel Mediant TP-1610 SIP - page 52

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 52 Document #: LTRT-72504 • You can configure the Trunk Group Se ttings t able to determine the method in which new calls are assigned t o channels within the trunk groups (a differe nt method for each trunk group can be config ured). For information on ho w to enable this option, refer to Section ...

  • Nortel Mediant TP-1610 SIP - page 53

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 53 July 2005 Table 5-4: IP to Trunk Group Routing Table Parameter Description Any SIP incoming call whose destination number matches t he prefix defined in the ‘Des tination Pho ne Prefix’ field and its source number matches the prefix defined in the adjacent ‘Source Phone Prefi x ...

  • Nortel Mediant TP-1610 SIP - page 54

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 54 Document #: LTRT-72504 5.8.4.4 Reasons for Alternative Routing The Reasons for Alternative Routi ng screen includes two tables (T el  IP and IP  Tel). Each t able enables you to define up to 4 different release reaso ns. If a call is released as a result of one of these reasons, the gateway ...

  • Nortel Mediant TP-1610 SIP - page 55

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 55 July 2005 5.8.5 Configuring the Profile Definitions Utilizing the Profiles feature, the Media nt 2000 pr ovides high-level adaptat ion whe n connected to a variety of equipment (from both Tel and IP side s) and protocols, each of which req uire a different system behavior. Using Prof ...

  • Nortel Mediant TP-1610 SIP - page 56

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 56 Document #: LTRT-72504 Note 2 : If not specified, the ptime gets a default value. Note 3 : The ptime specifies the maximum packeti zation time the gateway can receive. 5. Repeat steps 3 and 4 for the seco nd to fifth coders (optional). 6. Repeat steps 2 to 5 for the second to forth coder groups ( ...

  • Nortel Mediant TP-1610 SIP - page 57

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 57 July 2005 3. In the ‘Profile Preference’ drop-down list, select the preference (1-10) of the cu rrent Profile. The preference option is used to determine the prio rity of the Profile. If both IP and Tel profiles apply to the same call, the co ders an d other common parameters of ...

  • Nortel Mediant TP-1610 SIP - page 58

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 58 Document #: LTRT-72504 2. In the ‘Profile ID’ drop-down list, select the IP Profile you want to edit (up to four IP Profiles can be configured). 3. In the ‘Profile Preference’ drop-down list, select the preference (1-10) of the cu rrent Profile. The preference option is used to determine ...

  • Nortel Mediant TP-1610 SIP - page 59

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 59 July 2005 Table 5-5: Trunk Group Table Parameter Description Trunk ID The numbers (1-8) in the Trunk ID drop-do wn list represent the physical trunks on the back of the VoIP gateway. Channels To enable the trunk’s B-chann els, you must enter their number in this field. [n-m] repres ...

  • Nortel Mediant TP-1610 SIP - page 60

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 60 Document #: LTRT-72504 5.8.7 Configuring the Trunk Group Settings The Trunk Group Settings Table is u sed to determi ne the method in which new calls are assigned to B-channels within each trunk group. If such a rule doesn’t exist (for a specifi c Trunk group), the global rule, defined by the C ...

  • Nortel Mediant TP-1610 SIP - page 61

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 61 July 2005 Table 5-6: Channel Select Modes Mode Description By phone number Select the gateway port acco rding to the called number (ref er to the note below). Cyclic Ascending Select the next available channel i n an ascending cycle order. Al ways select the next higher channel n umb ...

  • Nortel Mediant TP-1610 SIP - page 62

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 62 Document #: LTRT-72504 5.9 Advanced Configuration Use this menu to set the gateway’s advanced configuration parameters (f or advanced users only). 5.9.1 Configuring the Network Settings From the Network Settings page you can define: • IP settings. • NTP settings. • Syslog settings. • SN ...

  • Nortel Mediant TP-1610 SIP - page 63

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 63 July 2005 5.9.1.1 Configuring the SNMP Managers Table The SNMP Managers table allows you to configur e the attributes of up to five SNMP managers.  To configure the SNMP Managers Table, take these 6 steps: 1. Access the ‘Network Settings’ screen ( Advanced Configuration menu & ...

  • Nortel Mediant TP-1610 SIP - page 64

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 64 Document #: LTRT-72504 maintenance, and debugging actions b ecome simp lified for the network admini strator. The NTP client follows a simple process in managing system time; the NTP client requests an NTP update, receives an NTP re sponse, and updates the lo cal system clock based on a configure ...

  • Nortel Mediant TP-1610 SIP - page 65

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 65 July 2005 5.9.2 Configuring the Channel Settings The Channels Settings screen enables you to set th e VoIP gatewa y channel parameters, such as Input and Output voice gain, Jitter buffer ch arac teristics, Modem, Fax and DTMF transport modes. These parameters are applied to all Media ...

  • Nortel Mediant TP-1610 SIP - page 66

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 66 Document #: LTRT-72504 5.9.3 Configuring the Trunk Settings  To configure the Trunk Settings, take these 9 steps: 1. Open the ‘Trunk Settings’ screen ( Advanced Config uration menu > Trunk Settings ); the ‘Trunk Settings’ screen is displayed. Initially, the screen appears with the p ...

  • Nortel Mediant TP-1610 SIP - page 67

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 67 July 2005 Table 5-7: Trunks Status Color Indicator Keys Indicator Color Description Gray Disabled Green Active-OK Yellow RAI Alarm Red LOS Alarm Blue AIS Alarm Orange D-channel Alarm (ISDN only) 3. To modify the selected trunk’s parameters, click the Stop Trunk button; the trunk is ...

  • Nortel Mediant TP-1610 SIP - page 68

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 68 Document #: LTRT-72504  Click the Close Windo w button. 7. After modifying the parameters:  To apply the changes to the selected trunk only, cli ck the Apply Trunk Settings button.  To apply the changes to all the trunks, click the Appl y to all Trunks button. The screen is refreshed, pa ...

  • Nortel Mediant TP-1610 SIP - page 69

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 69 July 2005 5.9.5 Restoring and Backing up the Gateway Configuration The Configuration File screen enabl es you to restore (load a ne w ini file to the gateway) or t o back up (make a copy of the VoIP gateway ini file and store it in a directo ry on your computer) the current configura ...

  • Nortel Mediant TP-1610 SIP - page 70

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 70 Document #: LTRT-72504 5.9.6 Regional Settings The ‘Regional Settings’ screen enabl es you to set an d view the gateway’s i nternal date and time and to load to the gate way the following configurat ion files: Call Progress To nes, CAS and Voice Prompts. For detailed information on the conf ...

  • Nortel Mediant TP-1610 SIP - page 71

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 71 July 2005 7. To save the loaded auxiliary files so they are available after a power fail, refer to Section 5.12 on page 84 . 8. To reset the Mediant 2000, refer to Section 5.12 on page 84 . 5.9.7 Changing the Mediant 2000 Username and Password To prevent unauthorized access to th e M ...

  • Nortel Mediant TP-1610 SIP - page 72

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 72 Document #: LTRT-72504 Note: The information in columns ‘Quality Status’ and ‘Quality Info.’ (per IP address) is reset if two minutes elapse without a call to that destination.  To view the IP connectivity information, take these 2 steps: 1. Set ‘AltRoutingTel2IPEnable’ to 1 or 2. ...

  • Nortel Mediant TP-1610 SIP - page 73

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 73 July 2005 Table 5-8: IP Connectivity Parameters Column Name Description Quality Info. Displays QoS information: delay and packet l oss, calculated according to previous calls. Note 1: This field is applicable only if the p arameter ‘AltRoutingTel2IPMode’ is set to 2 o r 3. Note 2 ...

  • Nortel Mediant TP-1610 SIP - page 74

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 74 Document #: LTRT-72504 Table 5-9: Call Counters Description (continues on pages 7 3 to 74) Counter Description Number of Established Calls This counter indicates the numbe r of estab lished calls. It is incremented as a result of one of the following release reasons, if the duration of the call i ...

  • Nortel Mediant TP-1610 SIP - page 75

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 75 July 2005 5.10.2 Monitoring the Mediant 2000 Trunks & Channels The Trunk & Channel Stat us screen provides real time monitorin g on the current status of the Mediant 2000 trunks & channels.  To monitor the status of the trun ks and B-channels take this step: • Open t ...

  • Nortel Mediant TP-1610 SIP - page 76

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 76 Document #: LTRT-72504 2. Click the submenu links to check/view a specific channel’s p arameter settings. Figure 5-26: Channel Status Details Screen 5.10.3 Activating the Internal Syslog Viewer The Message Log screen display s Syslog debug messages sent by the gateway. Note that it is not recom ...

  • Nortel Mediant TP-1610 SIP - page 77

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 77 July 2005 3. Select the messages, copy them and paste them into a text editor such as Notepad. Send this txt file to our Technical Support for diagnosis and troubleshooting. 4. To clear the screen of messages, click on the subm enu Message Log ; the screen is cleared and new messages ...

  • Nortel Mediant TP-1610 SIP - page 78

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 78 Document #: LTRT-72504 5.11 Software Update Menu The ‘Software Update’ menu enables users to upgra de the Mediant 2000 software by loading a new cmp file along with the ini and a suite of auxiliary files, or to update the exist ing auxiliary files. The ‘Software Update’ menu comprise s tw ...

  • Nortel Mediant TP-1610 SIP - page 79

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 79 July 2005 Note: At this point, the process can be canceled with no conse quence to the Mediant 2000 (click the Cancel button). If you continue the process (by clicking t he Start Software Upgrade button, the process must be follo wed through and completed with a Mediant 2000 reset at ...

  • Nortel Mediant TP-1610 SIP - page 80

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 80 Document #: LTRT-72504  Click Cancel ; the Mediant 2000 resets ut ilizing the cmp, ini and all other configuration files that were previously stored in flash me mory. Note that these are NOT the files you loaded in the previous Wizard steps.  Click Back ; the ‘Load a cmp File’ screen is ...

  • Nortel Mediant TP-1610 SIP - page 81

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 81 July 2005 Figure 5-33: Load a CPT File Screen 7. Follow the same procedure you followed when loading the ini file (refer to Step 6 ). The same procedure applies to the ‘Load a VP file’ (not applicable to the Mediant 2000 g ateway) screen and ‘Load a coefficient file’ screen. ...

  • Nortel Mediant TP-1610 SIP - page 82

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 82 Document #: LTRT-72504 Figure 5-35: ‘End Process’ Screen 9. Click the End Process button; the ‘Quick Setup’ screen appears and the full Web application is reactivated. 5.11.2 Auxiliary Files The ‘Auxiliary Files’ screen enables y ou to load to the gateway the following files: CAS, Cal ...

  • Nortel Mediant TP-1610 SIP - page 83

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 83 July 2005 Figure 5-36: Auxiliary Files Screen 2. Click the Browse button that is in the field for the type of file you want to load. 3. Navigate to the folder that contai ns the file you want to load. 4. Click the file and click the Open button; the name and path of the file appear i ...

  • Nortel Mediant TP-1610 SIP - page 84

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 84 Document #: LTRT-72504 5.12 Save Configuration The Save Configuration screen enables users to sav e the current paramete r configuration and the loaded auxiliary files to the non-volatile memory so they are availabl e after a power fail. Parameters that are only saved to th e volatile memory reve ...

  • Nortel Mediant TP-1610 SIP - page 85

    Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 85 July 2005 5.13 Resetting the Mediant 2000 The Reset screen enables you to remotely reset the gateway. Before reset you can choo se to save the gateway configuration to flash memory.  To reset the Mediant 2000, take these 3 steps: 1. Click the Reset button on the main menu bar; the ...

  • Nortel Mediant TP-1610 SIP - page 86

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 86 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 87

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 87 July 2005 6 ini File Configuration of the Mediant 2000 As an alternative to configuring th e VoIP gateway using the Web Interface (refe r to Section 5 on page 39 ), it can be configured by loading the ini file containing Customer-configured pa rameters. Th ...

  • Nortel Mediant TP-1610 SIP - page 88

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 88 Document #: LTRT-72504 6.3 The ini File Content The ini file contains the following SIP gateway information: • Basic, Logging, Web and RA DIUS parameters shown in Table 6-1 on page 90 . • SNMP parameters shown in Table 6-2 on page 98 . • SIP Configuration parameters shown in Table 6-3 on pa ...

  • Nortel Mediant TP-1610 SIP - page 89

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 89 July 2005 6.5 The ini File Example Figure 6-2 shows an example of an ini file for the VoIP gateway. Figure 6-2: SIP ini File Example PCMLawSelect = 1 ProtocolType = 1 TerminationSide = 0 FramingMethod = 0 LineCode = 2 TDMBusClockSource = 4 ClockMaster = 0 ...

  • Nortel Mediant TP-1610 SIP - page 90

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 90 Document #: LTRT-72504 6.6 Basic, Logging, Web and RADIUS Parameters Note: In Table 6-1 , parameters in brackets are the format in the Embedded Web Server * . Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range a ...

  • Nortel Mediant TP-1610 SIP - page 91

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 91 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription DNS2IP [Internal DNS Table] Internal DNS table, used to r esolve host names to IP addresses. ...

  • Nortel Mediant TP-1610 SIP - page 92

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 92 Document #: LTRT-72504 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription BaseUDPport [RTP Base UDP Port] Lower boundary of UDP port used for RT P, RTCP (Real-Time Control Protocol) (RT P port + ...

  • Nortel Mediant TP-1610 SIP - page 93

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 93 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription GwDebugLevel [Debug Level] Defines the S yslog logging level (usually set to 5 if debug trac ...

  • Nortel Mediant TP-1610 SIP - page 94

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 94 Document #: LTRT-72504 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription RAILowThreshold Low Threshold (in percentage ) that def ines the gateway‘s busy endpo ints. The range is 0 to 100. The ...

  • Nortel Mediant TP-1610 SIP - page 95

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 95 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription ResetWebPass word Allo ws resetting to default of Web password to: Username: “Admin” Pas ...

  • Nortel Mediant TP-1610 SIP - page 96

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 96 Document #: LTRT-72504 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription RA DIUSA uthPo rt [RADIUS Authentication Port] Port number of Authentication and Authorizat ion server. The default valu ...

  • Nortel Mediant TP-1610 SIP - page 97

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 97 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues on pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription BootPDelay The interval between the device’s startup and the first BootP/DHCP request that ...

  • Nortel Mediant TP-1610 SIP - page 98

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 98 Document #: LTRT-72504 6.7 SNMP Parameters Note: In Table 6-2 , parameters in brackets are the format in the Embedded Web Server * . Table 6-2: SNMP Parameter (continues on pages 9 8 to 99) ini File Field Name Web Parameter Name * Valid Range and De scription DisableSNMP [Enable SNMP] 0 = SNMP is ...

  • Nortel Mediant TP-1610 SIP - page 99

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 99 July 2005 Table 6-2: SNMP Parameter (continues on pages 9 8 to 99) ini File Field Name Web Parameter Name * Valid Range and De scription SetCommunityString Note: Obsolete parameter, use SNMPReadWriteCommunityString_x instead. SNMP community string (up to 1 ...

  • Nortel Mediant TP-1610 SIP - page 100

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 100 Document #: LTRT-72504 6.8 SIP Configuration Parameters Note: In Table 6-3 , parameters in brackets are the format in the Embedded Web Server * . Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription ControlI ...

  • Nortel Mediant TP-1610 SIP - page 101

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 101 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription EnableProxySRVQuery [Enable Proxy SRV Queries] Enables the use of DNS Service Record (SR V) queries to ...

  • Nortel Mediant TP-1610 SIP - page 102

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 102 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription ProxyRedundancy Mode [Redundancy Mode] 0 = Parking mode: gateway continues working wi th the last active Proxy until the next failu ...

  • Nortel Mediant TP-1610 SIP - page 103

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 103 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription AssertedIdMode [Asserted Identity Mode] 0 = None (default). 1 = P-asserted. 2 = P-preferred. The Assert ...

  • Nortel Mediant TP-1610 SIP - page 104

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 104 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription CoderName [Coders] CoderName = Coder,ptime (can ap pear up to 5 times) The following coder names can be selected: g711Alaw64k – G ...

  • Nortel Mediant TP-1610 SIP - page 105

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 105 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription AMRSendRate Determines the selected rate for the AMR coder . This parameter is releva nt only if AMR is ...

  • Nortel Mediant TP-1610 SIP - page 106

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 106 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription CngDetectorMode [CNG Detector Mode] 0 = Don’t detect CNG (default) 2 = Detect CNG on caller side and start fax session (if IsFaxU ...

  • Nortel Mediant TP-1610 SIP - page 107

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 107 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription XferPrefix [Transfer Prefix] Defined string t hat is added, as a pref ix, to the transferred called num ...

  • Nortel Mediant TP-1610 SIP - page 108

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 108 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription OutOfBandDTMFFormat [Out-of-Band DTMF Format] The exact method to send out-of-band DT MF digits 1 = INFO format (Nortel) 2 = INFO f ...

  • Nortel Mediant TP-1610 SIP - page 109

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 109 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription Profile Parameters CoderName_ID [Coder Group Settings] Coder list for Profiles (up to five coders in ea ...

  • Nortel Mediant TP-1610 SIP - page 110

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 110 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 110) ini File Field Name Web Parameter Name * Valid Range and De scription IPProfile_ID [IP Profile Settings] IPProfile_<Profile ID> = <Profile Name>,< Preference>,<Coder Group ID>,& ...

  • Nortel Mediant TP-1610 SIP - page 111

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 111 July 2005 6.9 ISDN and CAS Interworking-Related Parameters Note: In Table 6-4 , parameters in bracket s are the format in the Embedded Web Server * . Table 6-4: ISDN and CAS Inter working-Related Parameters (continues on pages 11 1 to 114) ini File Field ...

  • Nortel Mediant TP-1610 SIP - page 112

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 112 Document #: LTRT-72504 Table 6-4: ISDN and CAS Inter working-Related Parameters (continues on pages 11 1 to 114) ini File Field Name Web Parameter Name * Valid Range and De scription PlayRBTone2IP [Play Ringback Tone to IP] 0 = Ringback tone isn’t played (defau lt). 1 = Ringback tone is played ...

  • Nortel Mediant TP-1610 SIP - page 113

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 113 July 2005 Table 6-4: ISDN and CAS Inter working-Related Parameters (continues on pages 11 1 to 114) ini File Field Name Web Parameter Name * Valid Range and De scription PSTNAlertTimeout [PSTN Alert Timeout] Alert Timeout in seconds (ISDN T301 timer) for ...

  • Nortel Mediant TP-1610 SIP - page 114

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 114 Document #: LTRT-72504 Table 6-4: ISDN and CAS Inter working-Related Parameters (continues on pages 11 1 to 114) ini File Field Name Web Parameter Name * Valid Range and De scription CASTransportType [CAS Transport Type] 0 = Disable CAS relay (defa ult). 1 = Enable CAS relay mode u sing RFC 2833 ...

  • Nortel Mediant TP-1610 SIP - page 115

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 115 July 2005 6.10 Number Manipulation and Routing Parameters Note: In Table 6-5 , parameters in bracket s are the format in the Embedded Web Server * . Table 6-5: Number Manipulation and Routing Parameters (co ntinues on pages 115 to 121) ini File Field Name ...

  • Nortel Mediant TP-1610 SIP - page 116

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 116 Document #: LTRT-72504 Table 6-5: Number Manipulation and Routing Parameters (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription ChannelSelectMode [Channel Select Mode] Defines common rule of port allo cation for IP to TEL calls. • 0 = By phon ...

  • Nortel Mediant TP-1610 SIP - page 117

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 117 July 2005 Table 6-5: Number Manipulation and Routing Parameters (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription UseSourceNumber AsDisplay Name [Use Source Number as Display Name] 0 = Interworks the Te ...

  • Nortel Mediant TP-1610 SIP - page 118

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 118 Document #: LTRT-72504 Table 6-5: Number Manipulation and Routing Parameters (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription RouteModeTel2IP [Tel to IP routing Mode] 0 = Route calls before number manipulation (default) 1 = Route calls after ...

  • Nortel Mediant TP-1610 SIP - page 119

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 119 July 2005 Table 6-5: Number Manipulation and Routing Parameters (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription SourceNumberMapTel2IP [Source Phone Number Manipulation Table for T el  IP calls] Sou ...

  • Nortel Mediant TP-1610 SIP - page 120

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 120 Document #: LTRT-72504 Table 6-5: Number Manipulation and Routing Parameters (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription For ETSI ISDN variant, the following Number Plan and Type co mbi nations (Plan/Type) are supported in t he Destinati ...

  • Nortel Mediant TP-1610 SIP - page 121

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 121 July 2005 Table 6-5: Number Manipulation and Routing Parameters (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription FilterCalls2IP [Filter Calls To IP] 0 = Disabled (default) 1 = Enabled If the filter cal ...

  • Nortel Mediant TP-1610 SIP - page 122

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 122 Document #: LTRT-72504 6.11 E1/T1 Configuration Parameters Note: In Table 6-6 , parameters in bracket s are the format in the Embedded Web Server * . Table 6-6: E1/T1/J1 Configuration Parameters (c o ntinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scripti ...

  • Nortel Mediant TP-1610 SIP - page 123

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 123 July 2005 Table 6-6: E1/T1/J1 Configuration Parameters (c o ntinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription TerminationSide [ISDN Termination Side] Selects the ISDN termination side. A pplicable only to I ...

  • Nortel Mediant TP-1610 SIP - page 124

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 124 Document #: LTRT-72504 Table 6-6: E1/T1/J1 Configuration Parameters (c o ntinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDNNFASInterfaceID_x [NFAS Interface ID] Defines a different Interface ID for each T1 trunk. The valid range is 0 to 100. T ...

  • Nortel Mediant TP-1610 SIP - page 125

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 125 July 2005 Table 6-6: E1/T1/J1 Configuration Parameters (c o ntinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDNRxOverlap_x [Enable Receiving of Overlap Dialing] Enable / disable Rx ISDN overlap p er trun ...

  • Nortel Mediant TP-1610 SIP - page 126

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 126 Document #: LTRT-72504 Table 6-6: E1/T1/J1 Configuration Parameters (c o ntinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDN Flexible Behavior Parameters ISDN protocol is implemented in different Switches / PBXs b y different vendors. Several i ...

  • Nortel Mediant TP-1610 SIP - page 127

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 127 July 2005 Table 6-6: E1/T1/J1 Configuration Parameters (c o ntinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDNGeneralCCBehavior [General Call Control Behavior] 16 = The gateway clears down the call if i ...

  • Nortel Mediant TP-1610 SIP - page 128

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 128 Document #: LTRT-72504 6.12 Channel Parameters The Channel Parameters d efine the DTMF, fax and modem transf er modes. Refer to Appendix D on page 203 for a detailed description of Fax and Modem transfer mode s; refer to Section 8.2 on page 139 for detailed description on DTMF transport mode s. ...

  • Nortel Mediant TP-1610 SIP - page 129

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 129 July 2005 Table 6-7: Channel Parameters (continues on pages 128 to 1 31) ini File Field Name Web Parameter Name * Valid Range and Description CNGDetectorMode [CNG Detector Mode] 0 = Disable (default). 1 = Event Only (N/A). 2 = Relay. T.38 fax relay sessio ...

  • Nortel Mediant TP-1610 SIP - page 130

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 130 Document #: LTRT-72504 Table 6-7: Channel Parameters (continues on pages 128 to 1 31) ini File Field Name Web Parameter Name * Valid Range and Description V34ModemTransportTy pe [V.34 Modem Transport Type] V.34 Modem T ransport Type that the gateway uses. You can select: 0 = Transparent 2 = Mode ...

  • Nortel Mediant TP-1610 SIP - page 131

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 131 July 2005 Table 6-7: Channel Parameters (continues on pages 128 to 1 31) ini File Field Name Web Parameter Name * Valid Range and Description RFC2833PayloadTy pe [RFC 2833 Payload T ype] The RFC 2833 DT MF relay dynamic payload type. Range: 96 to 99, 106 ...

  • Nortel Mediant TP-1610 SIP - page 132

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 132 Document #: LTRT-72504 6.12.1 Dynamic Jitter Buffer Operation Voice frames are transmitte d at a fixed rate. If the frames arrive at th e other end at the same rat e, voice quality is perceived as good. In many ca ses, however, some frames can arrive slightly faster or slower than the other fram ...

  • Nortel Mediant TP-1610 SIP - page 133

    Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 133 July 2005 6.13 Configuration Files Parameters The configuration files (Call Prog ress Tones, PR T, Voice Prompt s and CAS) can be loaded to the Mediant 2000 via the Embedded Web Server (refer to Section 5.11.2 on page 82 ), or via TFTP session.  To loa ...

  • Nortel Mediant TP-1610 SIP - page 134

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 134 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 135

    Mediant 2000 SIP User’s Manual 7. Configuration Files Version 4.4 135 July 2005 7 Configuration Files This section describes the configuration ( dat ) files that are load (in addition to the ini file) to the gateway. The configuration files are: • Call Progress Tones file (refer to Section 7.1 below). • Prerecorded Tones file (ref er to Secti ...

  • Nortel Mediant TP-1610 SIP - page 136

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 136 Document #: LTRT-72504 • [CALL PROGRESS TONE #X] – containing the Xth tone definition (starting f rom 1 and not exceeding the number of Call Progress Tones d efi ned in the first section) using the followin g keys:  Tone Type – Call Progress Tone type Figure 7-1: Call Progress Tone Type ...

  • Nortel Mediant TP-1610 SIP - page 137

    Mediant 2000 SIP User’s Manual 7. Configuration Files Version 4.4 137 July 2005 7.2 Prerecorded Tones (PRT) File The Call Progress Tones mecha nism has several limitations, such a s a limited number of predefined tones and a li mited number of frequen cy integrations in o ne tone. To work a round these limitations and provide tone g eneration cap ...

  • Nortel Mediant TP-1610 SIP - page 138

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 138 Document #: LTRT-72504 When the list of recorded file s is converted to a single voiceprompts.dat file, every Voice Prompt is tagged with an ID number, starting with “1”. This ID is used la ter by the Mediant 2000 to start playing the correct announcement. Up to 1000 Voice Prompts can be use ...

  • Nortel Mediant TP-1610 SIP - page 139

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 139 July 2005 8 Gateway Capabilities Description 8.1 Proxy or Registrar Registration Example REGISTER sip:servername SIP/2.0 VIA: SIP/2.0/UDP 212.179.22.229;branch=z9hG4bRaC7AU234 From: <sip:GWRegistrationName@sipgatewayname>;tag=1c29347 To: <sip:GWRegistratio ...

  • Nortel Mediant TP-1610 SIP - page 140

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 140 Document #: LTRT-72504 8.3 ISDN Overlap Dialing Overlap dialing is a dialin g scheme used by severa l ISDN varia nts to send and / or receive called number digits one right aft er the other (or several at a time). As opposed to the enbloc dialing scheme in which a complete number is sent. The Me ...

  • Nortel Mediant TP-1610 SIP - page 141

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 141 July 2005 8.4 Using ISDN NFAS In regular (non-NFAS) T1 I SDN trunks, a single 64 kbps channel carrie s signaling for the oth er 23 B-channels of that particular T1 trunk. This ch annel is called the D-channel a nd usually reside s on timeslot # 24. The ISDN Non-Fac ...

  • Nortel Mediant TP-1610 SIP - page 142

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 142 Document #: LTRT-72504 To define an explicit Interface I D for a T1 tr unk (that is differe nt from the default), use the following parameters: • ISDNBehavior_x = 512 (x = 0 to 7 identi fying the Mediant 2000 physical trunk) • ISDNNFASInterfaceID_x = ID (x = 0 to 255) Note 1: Usually the Int ...

  • Nortel Mediant TP-1610 SIP - page 143

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 143 July 2005 8.5 Configuring the DTMF Transport Types You can control the way DTMF digits are transpo rte d over the IP network to the remote endpoint. The following five modes are suppo rted: 1. Using INFO message according to the Nortel IETF draft: In this mode DTMF ...

  • Nortel Mediant TP-1610 SIP - page 144

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 144 Document #: LTRT-72504 5. Sending DTMF digits (in RTP packets) as part of the audio stream (DTMF Rel ay is disabled): Note that this method is normally used with G.711 coders; with other Low Bit Rate (LBR) coders the quality of the DTMF digits is reduced. To set this mode:  ‘IsDTMFUsed = 0? ...

  • Nortel Mediant TP-1610 SIP - page 145

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 145 July 2005 Table 8-3: Summary of DTMF Configuration Param eters (continues on pages 144 to 1 45) ini File Field Name [Web Name] Valid Range and Description RxDTMFOption Defines the supporte d Receive DTMF negoti ation method. 0 = Don’t declare RFC 2833 Tele phony- ...

  • Nortel Mediant TP-1610 SIP - page 146

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 146 Document #: LTRT-72504 8.6 Configuring the Gateway’s Alternative Routing (based on Connectivity and QoS) The Alternative Routing fe ature enables reliable routing of Tel to I P calls when Proxy isn’t used. The Mediant 2000 gatewa y periodically checks th e av ailability of connectivity and s ...

  • Nortel Mediant TP-1610 SIP - page 147

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 147 July 2005 8.6.4 Relevant Parameters The following parameters (descri bed in Table 6-5 ) are used to configure the Alternative Rou ting mechanism: • AltRoutingTel2IPEnable • AltRoutingTel2IPMode • IPConnQoSMaxAllowedPL • IPConnQoSMaxAllowedDelay 8.7 Working ...

  • Nortel Mediant TP-1610 SIP - page 148

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 148 Document #: LTRT-72504 In the transfer scenario there are three parties: Party A - transferring, Party B – tr ansferred, Party C – transferred to. • A Calls B. • B answers. • A presses the hookflash and puts B on-h old (party B hears a hold tone) • A dials C. • After A completed di ...

  • Nortel Mediant TP-1610 SIP - page 149

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 149 July 2005 8.8 TDM Tunneling The Mediant 2000 TDM T unneling feature allo ws you to tunnel groups of digit al trunk spans o r timeslots (B-channels) ov er the IP network. TDM Tunneling utilizes the internal routi ng capabilities of the Mediant 2000 (working without ...

  • Nortel Mediant TP-1610 SIP - page 150

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 150 Document #: LTRT-72504 Figure 8-1: ini File Example for TDM Tunneling (Originating Side) EnableTDMOverIP = 1 ;E1_TRANSPARENT_31 ProtocolType_0 = 5 ProtocolType_1 = 5 ProtocolType_2 = 5 ProtocolType_3 = 5 prefix = '*,10.8.24.12' ;(IP address of the Mediant 2000 in the opposite location) ...

  • Nortel Mediant TP-1610 SIP - page 151

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 151 July 2005 8.9 Call Detail Report The Call Detail Report (CDR) contains vital statistic information on calls made by the gateway. CDRs are generated at the end and (optionally) at the begin ning of each call (determined by the parameter ‘CDRReportL evel ’ ). The ...

  • Nortel Mediant TP-1610 SIP - page 152

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 152 Document #: LTRT-72504 8.10 Trunk to Trunk Routing Example This example describes two Mediant 2000 gateways , each interfa ce with the PSTN through f our E1 spans. Gateway "A" is config ured to route all incoming Tel  IP calls to gateway "B". Gateway "B" generate ...

  • Nortel Mediant TP-1610 SIP - page 153

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 153 July 2005 8.11 SIP Call Flow Example The Call Flow, shown in Figure 8-3 , describes SIP messages exchanged between Mediant 2000 gateway and an MP-108 gateway during a simple call. MP-108 with phone number “8000”, calls Mediant 2000 with phone number “1 000” ...

  • Nortel Mediant TP-1610 SIP - page 154

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 154 Document #: LTRT-72504 F2 10.8.201.10 ==> 10.8.201.108 Try ing SIP/2.0 100 Trying Via: SIP/2.0/UDP 10.8.201.108;branch=z9hG4bKacsiJkDGd From: <sip:8000@10.8.201.108>;tag=1c5354 To: <sip:1000@10.8.201.10> Call-ID: 534366556655skKw-8000--1000@10.8.201.108 Server: Audiocodes-Sip-Gate ...

  • Nortel Mediant TP-1610 SIP - page 155

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 155 July 2005 CSeq: 18153 ACK Supported: 100rel,em Content-Length: 0 Note: Phone "8000" goes on-hook; gateway 10.8.201.108 sends "BYE" to gateway 10.8.201.10. Voice path is established. F6 10.8.201.108 ==> 10.8.201.10 BYE BYE sip:1000@10.8.201.10 ...

  • Nortel Mediant TP-1610 SIP - page 156

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 156 Document #: LTRT-72504 8.12 SIP Authentication Example Mediant 2000 gateway supports basic and dig est authentication types, according to SIP RFC 3261 standard. A proxy server mi ght require au thentication before forwarding an INVITE message. A Registrar/Pro xy server may also require authentic ...

  • Nortel Mediant TP-1610 SIP - page 157

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 157 July 2005 Using SIP protocol “sip” Proxy IP from ini file “10.2.2.222” The equation to be evaluated: “REGISTER:sip:10.2.2.222”. The MD5 algorithm is run on this equati on and stored for future usage. The result is:”a9a031 cfddcb10d91c8e7b 4926086f7e? ...

  • Nortel Mediant TP-1610 SIP - page 158

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 158 Document #: LTRT-72504 8.13 Nortel IMS Specific Features and Configuration 8.13.1 SIP2PRI Gateway  To enable Nortel’s IMS SIP2PRI gateway specific features, add the following parameters to the ini file: ApplicationProfile = 4444 IsProxyUsed = 1 SendInviteToProxy = 1 ProxyIP = <Proxy IP a ...

  • Nortel Mediant TP-1610 SIP - page 159

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 159 July 2005 For the SIP2PRI gateway to be able to apply the ro uting rule s on the combined string, the prefix (domain name and tru nk group) must previously b e defined in the IP to Tru nk Group Routing table either using the Embedded Web Server (refer to screen b e ...

  • Nortel Mediant TP-1610 SIP - page 160

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 160 Document #: LTRT-72504 Note: Usually each E1/T1 span is c onfigured as a separate trunk group. Different Domain names, according to the originated trunk group (or E1/T 1 spans), can be determined via the Tel to IP Routing table. To enable different domain names add the followin g parameters to t ...

  • Nortel Mediant TP-1610 SIP - page 161

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 161 July 2005 2. Use the number manipulation table (exemplified below) to assign NPI/TON val ues according to the number’s prefix: NumberMapIP2TEL= nortelnetworks.com/TrunkGroup3,30,$$,$$,1,2 In the above example, all numbers starting with t he ‘nortelnetworks.com/ ...

  • Nortel Mediant TP-1610 SIP - page 162

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 162 Document #: LTRT-72504 8.13.2 SIP2CAS (Call Pilot) Gateway  To enable SIP2CAS gateway specifi c features, take these 2 steps: 1. Add the following parameters to the ini file: ApplicationProfile=1 IsProxyUsed = 1 SendInviteToProxy = 1 ProxyIP = <Proxy IP address> EnableHold = 1 EnableTra ...

  • Nortel Mediant TP-1610 SIP - page 163

    Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 163 July 2005 • If the call transfer fails, the gateway either plays a busy tone (if the destination client to whom the call is transferred is b usy) or it plays a reorder tone (fo r all other reasons). The tone is played for 10 seconds (TimeForRe orderTone=10) towar ...

  • Nortel Mediant TP-1610 SIP - page 164

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 164 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 165

    Mediant 2000 SIP User’s Manual 9. Diagnostics Version 4.4 165 July 2005 9 Diagnostics Several diagnostic tools a re provided, enabling you to identify correct fu nctioning of the Mediant 2000, or an error condition with a probable cause and a solutio n or workaround. • Front panel indicator LEDs on the Mediant 2000. Th e location and functional ...

  • Nortel Mediant TP-1610 SIP - page 166

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 166 Document #: LTRT-72504 9.2.1 Syslog Servers Users can use the provided Syslog serv er (ACSyslog08.exe) or other third-party Syslog serv ers. Examples of Syslog serv ers available as sharew are o n the Internet: • Kiwi Enterprises: http://www.kiwisyslog.com/ • The US CMS Server: http://uscms. ...

  • Nortel Mediant TP-1610 SIP - page 167

    Mediant 2000 SIP User’s Manual 10. BootP/DHCP Support Version 4.4 167 July 2005 10 BootP/DHCP Support 10.1 Startup Process The startup proces s (illustrated in Figure 10-1 on page 168 ) begins when the gateway is reset (physically or from the We b / SNMP) and ends when the operational software is run ning. In the startup process, the netwo rk par ...

  • Nortel Mediant TP-1610 SIP - page 168

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 168 Document #: LTRT-72504 Figure 10-1: Mediant 2000 Startup Process DHCP x time s BootP/DHCP reply contains firmware file name ? Download firmware v ia TFTP BootP/DHCP reply contains ini file name? Download configuration files via TFTP Run operational software No No Update network parameters from B ...

  • Nortel Mediant TP-1610 SIP - page 169

    Mediant 2000 SIP User’s Manual 10. BootP/DHCP Support Version 4.4 169 July 2005 10.2 DHCP Support When the gateway is co nfigured to use DHCP (DHCPEnable = 1), it attempts to contact the enterprise’s DHCP server to obtain the networki ng parameters (IP address, subnet mask, default gateway, primary/secondary DNS server and SI P server ad dress) ...

  • Nortel Mediant TP-1610 SIP - page 170

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 170 Document #: LTRT-72504 • From version 4.4 to version 4.4 or to any highe r version, the devi ce retains its configuration ( ini file), however, the auxiliary file s (CPT, logo, etc.) may be erased. When using the Software Upgrade wizard, available through the Web Interface (refer to Section 5. ...

  • Nortel Mediant TP-1610 SIP - page 171

    Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 171 July 2005 11 SNMP-Based Management Simple Network Manage ment Protocol (SNMP) is a standard-based netwo rk control protoco l used to manage element s in a network. The SN MP M anager (usually implement ed by a Network Manager (NM) or an Element Manag er (EM)) co nnect s to a ...

  • Nortel Mediant TP-1610 SIP - page 172

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 172 Document #: LTRT-72504 • Trap Message - The SNMP standard furnishes a mech anism by which devices can ‘re ach out’ to a Network Manager on their own (via a ‘t rap’ message) to notify or alert the man ager of a problem with the device. This typically requires ea ch device on the n etwor ...

  • Nortel Mediant TP-1610 SIP - page 173

    Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 173 July 2005 11.2 Carrier Grade Alarm System The basic alarm system has been extended to a carrier-grade alarm system. A carrier-grade alarm system provide s a reliable alarm report ing mechanism that takes into ac count EMS outages, network outages , and transport mechanism su ...

  • Nortel Mediant TP-1610 SIP - page 174

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 174 Document #: LTRT-72504 11.4 Third-Party Performance Monitoring Measurements Performance measurements are avail able for a third-party performance m onitoring system through an SNMP interfa ce. These measurements can be polled at sche duled intervals by an external poller or utility in a media se ...

  • Nortel Mediant TP-1610 SIP - page 175

    Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 175 July 2005 Note: The acBoard MIB is still supported but is being replaced by five newer proprietary MIBs. The acBoard MIB has the following groups:  boardConfiguration  boardInformation  channelConfiguratio n  channelStatus  reset  acTrap As noted above, fiv ...

  • Nortel Mediant TP-1610 SIP - page 176

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 176 Document #: LTRT-72504 acAlarmVarbinds and also in acBoar d.acTrap. acBoardTrapDefinitions. oid_1_3_6_1_4_1_500 3_9_10_1_21_2_0). The table size can be altered via notificationLogMIB.notificati onLogMIBObjects.nlmConfig.nlmCo nfigGlobalEntryLimit or notificationLogMIB.notificationLogMIBOb jects. ...

  • Nortel Mediant TP-1610 SIP - page 177

    Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 177 July 2005 11.6 SNMP Interface Details This section describes det ails of the SNMP inte rface that is requi red when developing an Element Manager (EM) for any of the Tru nkPack-VoP Series products, or to manage a device with a MIB browser. Currently, both SNMP and ini file c ...

  • Nortel Mediant TP-1610 SIP - page 178

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 178 Document #: LTRT-72504  To change the only r ead-write community string from v2admin to v2mgr, take these 4 steps: 1. Follow the procedure above to add a read-write com munity string to a row for v2mgr. 2. Set up the EM so that subsequent ‘set’ requ ests use the new community string, v2mg ...

  • Nortel Mediant TP-1610 SIP - page 179

    Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 179 July 2005 1. Add a row to the snmpTargetAddrTable with these values: Name=mgr0, TagList =MGR, Params= v2cparams. 2. Add a row to the tgtAddressMaskTable table with these values: Name=m gr0, tgtAddressMask=255.255.255.25 5:0. The agent does not allow creation of a row in this ...

  • Nortel Mediant TP-1610 SIP - page 180

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 180 Document #: LTRT-72504 11.6.4 Multiple SNMP Trap Destinations An agent can now send traps to up to five managers. For each man ager, set the following parameters defined in the snmpMan agersTable in the acBoardMIB: • snmpTrapManagerSen ding • snmpManagerIsUsed • snmpManagerTrapPort • snm ...

  • Nortel Mediant TP-1610 SIP - page 181

    Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 181 July 2005 Figure 11-1: Example of Entries in a Dev i ce ini file Rega rding SNMP ; SNMP trap destinations ; The board maintains a table of trap destinations containing 5 ;rows. The rows are numbered 0..4. Each block of 4 items below ;apply to a row in the table. ; To configu ...

  • Nortel Mediant TP-1610 SIP - page 182

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 182 Document #: LTRT-72504  To disable a trap destination: • Change TagList on the approp riate row in the snmpTargetAddrTabl e to the empty string.  To enable a trap destination: • Change TagList on the approp riate row in the snmpTargetAddrTabl e to ‘AC_TRAP’. 11.7 SNMP Manager Backw ...

  • Nortel Mediant TP-1610 SIP - page 183

    Mediant 2000 SIP User’s Manual 12. Selected Technical Specifications Version 4.4 183 July 2005 12 Selected Technical Specifications Table 12-1: Mediant 2000 Selected Technical Spe cifications (continues on pages 183 to 185) Function Specification Trunk & Channel Capacity 1 Capacity with E1 1, 2, 4, 8 or 16 E1 spans, 30, 60, 120, 240 or 480 di ...

  • Nortel Mediant TP-1610 SIP - page 184

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 184 Document #: LTRT-72504 Table 12-1: Mediant 2000 Selected Technical Spe cifications (continues on pages 183 to 185) Function Specification Fax Transparen cy Automatic fax bypass (pass-through) to G.711, ADPCM or NSE bypass mode Modem Transparenc y Automatic s witching (pass-through) to PC M, ADPC ...

  • Nortel Mediant TP-1610 SIP - page 185

    Mediant 2000 SIP User’s Manual 12. Selected Technical Specifications Version 4.4 185 July 2005 Table 12-1: Mediant 2000 Selected Technical Spe cifications (continues on pages 183 to 185) Function Specification Environmental (AC) Operation Temp: 0° to 40° C / 32° to 104° F Storage: -40° to 70° C / -40° to 158° F Humidity: 10 to 90% non-con ...

  • Nortel Mediant TP-1610 SIP - page 186

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 186 Document #: LTRT-72504 Reader's Notes ...

  • Nortel Mediant TP-1610 SIP - page 187

    Mediant 2000 SIP User’s Manual A. Mediant 2000 SIP Software Kit Version 4.4 187 July 2005 Appendix A Mediant 2000 SIP Sof tware Kit Table A-1 describes the standard supplied software kit for Me diant 2000 SIP gateways. The supplied documentation include s this User’s Manual, the Mediant 2000 Fast Track and the Mediant 2000 & TP-1610 SIP Rel ...

  • Nortel Mediant TP-1610 SIP - page 188

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 188 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 189

    Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 189 July 2005 Appendix B The BootP/TFTP Configuration Utility The BootP/TFTP utility enables you to easily configure and provision our b oards and media gateways. Similar to third-party BootP/TFTP utilities (which are al so supported) but with added functionality; ...

  • Nortel Mediant TP-1610 SIP - page 190

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 190 Document #: LTRT-72504 • Protection against entering faulty information. • Rem ote r ese t. • Unicast BootP response. • User-initiated BootP respond, for remote provisioning over WA N. • Filtered display of BootP requests. • Location of other BootP utilities t hat contain the same MA ...

  • Nortel Mediant TP-1610 SIP - page 191

    Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 191 July 2005 B.7 BootP/TFTP Application User Interface Figure B-1 shows the main application sc reen for the BootP/TFTP utility. Figure B-1: Main Screen B.8 Function Buttons on the Main Screen Pause: Click this button to pause the BootP Tool so that no replies are ...

  • Nortel Mediant TP-1610 SIP - page 192

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 192 Document #: LTRT-72504 When a gateway resets, it first sen ds a BootRe quest. Therefore, Reset can be used to force a BootP session with a gateway without needing to power cycle the gateway. As with any BootP session, the comp uter running the BootP Tool mu st be located on the same subnet as th ...

  • Nortel Mediant TP-1610 SIP - page 193

    Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 193 July 2005 B.10 Setting the Preferences The Preferences windo w, Figure B-3 , is used to configure the BootP Tool parameters. Figure B-3: Preferences Screen B.10.1 BootP Preferences ARP is a common acronym for Address Resoluti on Protocol, and is the method used ...

  • Nortel Mediant TP-1610 SIP - page 194

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 194 Document #: LTRT-72504 • ARP Type: The type of entry made into the ARP cache on the computer, once ARP Manipulation is enabled, can be eithe r Dyn ami c or Static . Dynamic entries expire after a period of time, keeping the cache clean so t hat stale entries do not consume computer resources. ...

  • Nortel Mediant TP-1610 SIP - page 195

    Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 195 July 2005 B.11 Configuring the BootP Clients The Clients window, shown in Figure B-4 below, is used to set up the pa rameters for each specific VoIP gateway. Figure B-4: Client Configuration Screen B.11.1 Adding Clients Adding a client creates an entry in the B ...

  • Nortel Mediant TP-1610 SIP - page 196

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 196 Document #: LTRT-72504  To add a client to the list using a template, take these 5 steps: 1. Click on the Add New Client Icon; a client with blank parameters i s displayed. 2. In the field Template , located on the right side of the Client Configuration Windo w , click on the down arrow to th ...

  • Nortel Mediant TP-1610 SIP - page 197

    Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 197 July 2005 B.11.5 Setting Client Parameters Client parameters are liste d on the right side of the Client Configuration Window . • Client MAC: The Client MAC is used by BootP to identify the VoIP gateway. The MAC address for the VoIP gateway is printed on a la ...

  • Nortel Mediant TP-1610 SIP - page 198

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 198 Document #: LTRT-72504 • Call Agent: This field spe cifies the IP address of the MGCP Call Agent that is controlling the gateway. This field can be ignored for all other control /signaling protocol s. B.11.6 Using Command Line Switches You can add command line swit ches in the field Boot File ...

  • Nortel Mediant TP-1610 SIP - page 199

    Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 199 July 2005 B.12 Managing Client Templates Templates can be used to simplify configuratio n of clients when most of the parameters are the same. Figure B-5: Templates Screen  To create a new template, take these 4 steps: 1. Click on the Add New Template button ...

  • Nortel Mediant TP-1610 SIP - page 200

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 200 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 201

    Mediant 2000 SIP User’s Manual C. RTP/RTCP Payload Types and Port Allocation Version 4.4 201 July 2005 Appendix C RTP/RTCP P ayload T ypes and Port Allocation RTP Payload Types are defined in RFC 18 89 and RFC 1890. We have ad ded new payload types to enable advanced use of other coder types. These types are rep ort edly not used by other applica ...

  • Nortel Mediant TP-1610 SIP - page 202

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 202 Document #: LTRT-72504 Payload Ty pe Description Basic Packet Rate [msec] 53 NetCoder 8.0 kbps 20 54 NetCoder 8.8 kbps 20 55 NetCoder 9.6 kbps 20 56 Transparent PCM 20 96 DTMF rela y per RFC 2833 102 Fax Bypass 20 103 Modem Bypass 20 104 RFC 2198 (Redun dancy) Same as channel’s voice coder. 10 ...

  • Nortel Mediant TP-1610 SIP - page 203

    Mediant 2000 SIP User’s Manual D. Fax and Modem Transport Mode s Version 4.4 203 July 2005 Appendix D Fax and Modem T ransport Modes D.1 Fax/Modem Settings Users can choose to use f or fax, and for each m odem type (V.22/ V.23/Bell/V.32/V.34), one of the following transport methods: • Fax relay mode (demodulation / remodul ation, not applicable ...

  • Nortel Mediant TP-1610 SIP - page 204

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 204 Document #: LTRT-72504 D.1.3 Supporting V.34 Faxes V.34 fax machine support is available only in by pa ss mode (fax relay is not supported ) when the channel is configured in one of the confi gurations described below: FaxTransportMode = 2 (Bypass) V34ModemTransportType = 2 (Modem bypass) In thi ...

  • Nortel Mediant TP-1610 SIP - page 205

    Mediant 2000 SIP User’s Manual E. Mediant 2000 Clock Settings Version 4.4 205 July 2005 Appendix E Mediant 2000 Clock Settings The gateway can either ge nerate its own timing sign al s, using an internal clo ck, or recover them from one of the E1/T1 trunks. a . To use the internal gateway clock source configure the following parameters: • TDMBu ...

  • Nortel Mediant TP-1610 SIP - page 206

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 206 Document #: LTRT-72504 Reader's Notes ...

  • Nortel Mediant TP-1610 SIP - page 207

    Mediant 2000 SIP User’s Manual F. Cu stomizing the Mediant 2000 Web Interface Version 4.4 207 July 2005 Appendix F Customizing the Mediant 2000 W eb Interface Customers incorporating the Me diant 2000 into their portfolios can customize the device’s Web Interface to suit their specific corp orate logo an d product naming conventions. Customers ...

  • Nortel Mediant TP-1610 SIP - page 208

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 208 Document #: LTRT-72504 2. In the URL field, append the suffix ‘AdminPage’ (note that it’s case-sensitive) to the IP address, e.g., http://10.1.229.17/AdminPage. 3. Click Image Load to Device ; the Image Download screen is displayed (shown in Figure F-3 ). Figure F-3: Image Download Screen ...

  • Nortel Mediant TP-1610 SIP - page 209

    Mediant 2000 SIP User’s Manual F. Cu stomizing the Mediant 2000 Web Interface Version 4.4 209 July 2005 Table F-1: Cu stomizable L ogo ini File Parameters Parameter Description LogoFileName The name of the image f ile contain ing your corporate lo go. Use a gif, jpg or jpeg image file. The default is AudioCodes ’ logo file. Note: The length of ...

  • Nortel Mediant TP-1610 SIP - page 210

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 210 Document #: LTRT-72504 6. To save the image to flash memory so it is available after a power fail, refer to Section 5.12 on page 84 . The new background appe ars on all Web Interface screens. Tip 1: If you encounter any problem during the loading of the files, or y ou want to restore the default ...

  • Nortel Mediant TP-1610 SIP - page 211

    Mediant 2000 SIP User’s Manual F. Cu stomizing the Mediant 2000 Web Interface Version 4.4 211 July 2005 F.4 Modifying ini File Parameters via the Web AdminPage  To modify ini file parameters via the Ad minPage, take these 6 steps: 1. Access the Mediant 2000 Embedded Web Server (refer to Section 5.6 on page 41 ). 2. In the URL field, append the ...

  • Nortel Mediant TP-1610 SIP - page 212

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 212 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 213

    Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 213 July 2005 Appendix G Accessory Programs and T ool s The accessory applications and tools shipped with th e device provide you with friendly interfaces that enhance device usability and smooth your tr ansition to the new VoIP inf rastructure. The following applications ...

  • Nortel Mediant TP-1610 SIP - page 214

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 214 Document #: LTRT-72504 G.1.1 Converting a CPT ini File to a Binary dat File For detailed information on creatin g a CPT ini file, refer to Section 7.1 on page 135 .  To convert a CPT ini file to a binary dat file, take these 10 steps: 1. Execute the TrunkPack Downloadable Conversi on Utility, ...

  • Nortel Mediant TP-1610 SIP - page 215

    Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 215 July 2005 G.1.2 Creating a Loadable Voice Prompts File For detailed information on the Voic e Prompts file, ref er to Section 7.2 on page 137 .  To create a loadable Voice Prompts dat file from your voice recording files, take these 7 steps: 1. Execute the TrunkPac ...

  • Nortel Mediant TP-1610 SIP - page 216

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 216 Document #: LTRT-72504 4. Arrange the files according to your require ments by dragging and droppin g them from one location in the list to another. Note that the sequence of the files determines their assigned Voice Prompt ID. Tip 1: Use the Play button to play wav files through your PC speaker ...

  • Nortel Mediant TP-1610 SIP - page 217

    Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 217 July 2005 G.1.3 Encoding / Decoding an ini File For detailed information on secure d ini file, refer to Section 6.1 on page 87 .  To encode an ini file, take these 6 steps: 1. Execute the TrunkPack Downloadable Conversi on Utility, DConvert240.exe (supplied with th ...

  • Nortel Mediant TP-1610 SIP - page 218

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 218 Document #: LTRT-72504 G.1.4 Creating a Loadable Prerecorded Tones File For detailed information on the PRT file, refer to Section 7.2 on page 137 .  To create a loadable PRT dat file from your raw da ta files, take these 7 steps: 1. Prepare the prerecorded tones (raw data PCM or L8) files yo ...

  • Nortel Mediant TP-1610 SIP - page 219

    Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 219 July 2005  Click the Add File(s) button; the ‘Select Files’ screen opens. Select the requi red Prerecorded Tone files an d press the Add>> button. Close the ‘Select Files’ screen. 5. For each raw data file, define a Tone Type, a Coder and a Defa ult D ...

  • Nortel Mediant TP-1610 SIP - page 220

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 220 Document #: LTRT-72504 G.2 PSTN Trace Utility These utilities are designed to convert PSTN trace binary files to textual form. The binary PSTN trace files are generated when the User se ts the PSTN interface to trace mode. G.2.1 Operation Generating textual trace/audit file for CAS pro toc o ls ...

  • Nortel Mediant TP-1610 SIP - page 221

    Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 221 July 2005 Figure H-8: Trunk Traces Figure H-9: UDP2File Utility ...

  • Nortel Mediant TP-1610 SIP - page 222

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 222 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 223

    Mediant 2000 SIP User’s Manual H. Software Upgrade Key Version 4.4 223 July 2005 Appendix H Sof tware Upgrade Key H.1 About the Software Upgrade Key Mediant 2000 gateways are sup plied with a Software Upgrade Key alrea dy pre-configured for each of its TrunkPack Modules (TPM). Users can later upg rade their Mediant 2000 fe atur es, capabilities a ...

  • Nortel Mediant TP-1610 SIP - page 224

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 224 Document #: LTRT-72504 H.3.1 Loading the Software Upgrad e Key Using the Embedded Web Server  To load a Software Upgrade Key us ing the Web Server, take these 5 steps: 1. Access the devices Embedded Web Server (refer to Section 5.5 on page 40 ). 2. Click the Softw are Update button. 3. Click ...

  • Nortel Mediant TP-1610 SIP - page 225

    Mediant 2000 SIP User’s Manual H. Software Upgrade Key Version 4.4 225 July 2005 Figure H-2: Example of a Soft ware Upgrade Key File Containing Multiple S/N Lines H.3.2 Loading the Software Upgr ade Key Using BootP/TFTP  To load the Software Upgrade Key file using Boot P/TFTP, take these 5 steps: 1. Place the file in the same location you’ve ...

  • Nortel Mediant TP-1610 SIP - page 226

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 226 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 227

    Mediant 2000 SIP User’s Manual I. Release Reason Mapping Version 4.4 227 July 2005 Appendix I Release Reason Mapping Table I-1 below de scribes the mapping of ISDN release rea son to SIP response. Table I-2 on page 229 describes the mapping of SIP response to ISDN relea se reason. Table I-1: Mapping of ISDN Release Reason to SIP Response (continu ...

  • Nortel Mediant TP-1610 SIP - page 228

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 228 Document #: LTRT-72504 ISDN Release Reason Description SIP Response Description 66 Channel type not implem ented 480 * Temporaril y unavailable 69 Requested facility not implem ented 503 * Service unavailable 70 Only restricted digital information be arer capability is availabl e 503 * Service u ...

  • Nortel Mediant TP-1610 SIP - page 229

    Mediant 2000 SIP User’s Manual I. Release Reason Mapping Version 4.4 229 July 2005 Table I-2: Mapping of SIP Response to ISDN Release Reason SIP Response Description ISDN Release Reason Description 400 * Bad request 31 Normal, unspecified 401 Unauthoriz ed 21 Call rejected 402 Payment required 21 Call rejected 403 Forbidden 21 Call re jected 404 ...

  • Nortel Mediant TP-1610 SIP - page 230

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 230 Document #: LTRT-72504 Reader’s Notes ...

  • Nortel Mediant TP-1610 SIP - page 231

    Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 231 July 2005 Appendix J SS7 T unneling The Signaling System 7 (SS7) tunneling feature fa cilitates peer-to-pee r transport of SS7 links between gateways that support A udioCodes' unique MTP2 (Message Transfer Part) Tunnel ing application (M2TN) for transferring S S7 MTP2 link data ...

  • Nortel Mediant TP-1610 SIP - page 232

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 232 Document #: LTRT-72504 J.1 MTP2 Tunneling Technology The SS7 tunneling technology is based on a pairi ng of remote and central gate ways, as shown in Figure J-3 . The remote gateways are configured to bac khaul MTP layer 2 signaling over the IP network using standard M 2UA protocol (over SCTP p ...

  • Nortel Mediant TP-1610 SIP - page 233

    Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 233 July 2005 J.3 SS7 Parameters The parameters in Table J-1 below configure all MTP attributes simultaneo usly. To set each MTP attribute individually, add _xx (xx equals the element number in th e range of 0 to 2) to the end o f the ini file field name. Table J-1: SS7 Parameters (conti ...

  • Nortel Mediant TP-1610 SIP - page 234

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 234 Document #: LTRT-72504 Table J-1: SS7 Parameters (continue s on pages 2 33 to 234) ini File Parameter Name Description SS7_MTP2_Param_Timer _T6 Defin es the SS7 MTP2 Remote Congestion timer (in msec). The valid range is 0 to 10000. The default value is 6000. SS7_MTP2_Param_Timer _T7 Defin es the ...

  • Nortel Mediant TP-1610 SIP - page 235

    Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 235 July 2005 Table J-2: SIGTRAN Interface Groups (con tinues o n pages 234 to 235) ini File Parameter Name Description SS7_LOCAL_SCTP_PORT Determines the SIGTRAN group SCTP port. The valid range is 0 to 0x FFFE. The default value is 0Xfffe. SS7_SIG_NETWORK Determines the SIGTRAN group N ...

  • Nortel Mediant TP-1610 SIP - page 236

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 236 Document #: LTRT-72504 J.4.3 SS7 Signaling Link Table J-4: SS7 Signaling Link (continues on page s 236 to 2 37) ini File Parameter Name Description SS7_LINK_INDEX Determines the index field for a line. The valid range is 0 to 7. The default value i s 0. SS7_LINK_ROWSTATUS Determines the Ro wStat ...

  • Nortel Mediant TP-1610 SIP - page 237

    Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 237 July 2005 Table J-4: SS7 Signaling Link (continues on page s 236 to 2 37) ini File Parameter Name Description SS7_LINK_GROUP_ID Determines the group ID (M3 UA) of signaling link. The valid range is 0 to 0x FFFF. The default value is 0 . ATM_SAAL_LINK_PROFILE_NUM Determines the ATM SA ...

  • Nortel Mediant TP-1610 SIP - page 238

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 238 Document #: LTRT-72504 • There are 8 SS7 links - 4 links of type: MTP2 MGC, and 4 links of type MTP2. Each pair of links (1 MTP2 MGC and 1 MTP2) defines an MTP2 tunnel. • There is 1 interface that is used for the M2UA MGC <=> M2UA SG (Signaling Gateway) connectio n. • There are 4 int ...

  • Nortel Mediant TP-1610 SIP - page 239

    Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 239 July 2005 Figure J-4: SS7 MTP2 Tunneling ini File Example - MGC SS7_MTP2_PARAM_TIMER_T4E_0=500 SS7_MTP2_PARAM_TIMER_T4N_0=8200 SS7_MTP2_PARAM_TIMER_T5_0=100 SS7_MTP2_PARAM_TIMER_T6_0=3000 SS7_MTP2_PARAM_TIMER_T7_0=2000 [syslog] SYSLOGSERVERIP = 168.100.0.1 ENABLESYSLOG = 1 ;FORCEEXCE ...

  • Nortel Mediant TP-1610 SIP - page 240

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 240 Document #: LTRT-72504 Figure J-4: SS7 MTP2 Tunneling ini File Example - MGC SS7_SIG_IF_GROUP_TABLE 4 = 4, 77, 4, 1, 2000, 2000, 30000, 1, 0, 2904, 1,2904,168.100.0.2,3,3; [ SS7_SIG_IF_GROUP_TABLE ] [ SS7_SIG_INT_ID_TABLE ] FORMAT SS7 _ SIG _ IF _ ID _ INDEX = SS7 _ SIG _ IF _ ID _ VALUE, SS7 _ ...

  • Nortel Mediant TP-1610 SIP - page 241

    Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 241 July 2005 Figure J-5: SS7 MTP2 Tunneling ini File Example - SG SS7_LINK_TABLE 1 = new_link_1, 0, 2, 1,1, 2, 12, 12; SS7_LINK_TABLE 2 = new_link_2, 0, 2, 1, 1, 4, 7,18; SS7_LINK_TABLE 3 = new_link_3, 0, 2, 1, 1, 5, 3,1; [SS7_LINK_TABLE] [ SS7_SIG_IF_GROUP_TABLE ] FORMAT SS7_SIG_IF_GR ...

  • Nortel Mediant TP-1610 SIP - page 242

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 242 Document #: LTRT-72504 Table J-5: Table of Parameter Values Example - Remote Mana gement Connections Index Fields: 1. Connection Number Connection Number User Name User Password Time Connected (msec) Permissions 0 Admin Yellow9 0 All 1 Gillian Red5 1266656 Read Only 2 David Orange6 0 Read Write ...

  • Nortel Mediant TP-1610 SIP - page 243

    Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 243 July 2005 J.6.3 Tables of Parameter Value Rules in the ini File Structure The ini file allows you to add/modify parameters in tables. When using tables, Read-Only parameters are not loaded, since they cau se an error when trying to download the loaded file. Therefore read-only param ...

  • Nortel Mediant TP-1610 SIP - page 244

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 244 Document #: LTRT-72504 • The order of the Data fields in the Format line is not significant (unli ke the Index-fields). Field values in Data lines are int erpreted according to the order sp ecified in the Format line. • The sign '$$' in the Data line means that t he user wants the ...

  • Nortel Mediant TP-1610 SIP - page 245

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 245 July 2005 Appendix K RADIUS Bil ling and VXML Calling Card Application The Mediant 2000 calling card appli cation capability (included in its IVR - Interactive Voice Response - feature) e nables Internet Telephony Service Provid ers (ITSPs) to provi ...

  • Nortel Mediant TP-1610 SIP - page 246

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 246 Document #: LTRT-72504 • Loads the VXML scripts once and stores them in t he RAM; scripts can be changed witho ut the need of reset • Barge-in dialing (to shorten menu time), once p rompt has started K.3 Supported Architecture Figure K-1: Mediant 2000 Supported Architecture Figure K-1 illust ...

  • Nortel Mediant TP-1610 SIP - page 247

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 247 July 2005 K.4 Implementation The Mediant 2000 uses an emb edded VoiceXML interpreter to in terpret and execute standard VoiceXML scripts, which are lo aded from an outbound HTTP server and stored in the gateway ’s volatile memory (RAM). The pre de ...

  • Nortel Mediant TP-1610 SIP - page 248

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 248 Document #: LTRT-72504 K.4.2 Call Flow Description Figure K-2 on the previous p age depicts a n example of a standard PSTN  IP call (billin g-model: debit). • An incoming PSTN call with a publi shed access number reaches the Mediant 2000. • The Mediant 2000 accepts the call (sen ds an Ale ...

  • Nortel Mediant TP-1610 SIP - page 249

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 249 July 2005 K.5 Operation & Configuration  To start working with the IVR system, take these 6 steps: 1. Install the Mediant 2000 (refer to Section Installing the Mediant 2000 on page 27 and to Section Getting Started on page 35 ). 2. Create and ...

  • Nortel Mediant TP-1610 SIP - page 250

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 250 Document #: LTRT-72504 ini File Field Name Valid Range and Description IVR Reference NumberMapIP2Tel Manipulate the destinati on number for IP to Tel calls. NumberMapIP2Tel = a,b,c,d,e,f,g,h,i a = Destination number prefix b = Number of stripped digits from the left, or (if brackets are used) fr ...

  • Nortel Mediant TP-1610 SIP - page 251

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 251 July 2005 • RADIUSAuthServerIP • RADIUSAuthPort • RADIUSAccServerIP • RADIUSAccPort • AAAIndications • RADIUSAccountingType K.7 Supported RADIUS Attributes Use Table K-3 below for explanations on the RADIUS attributes contained in th e c ...

  • Nortel Mediant TP-1610 SIP - page 252

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 252 Document #: LTRT-72504 Table K-3: Supported RADIUS Attributes (continues on page s 251 to 252) Attribut e Number Attribute Name VS A No. Pu rpose Value Format Sample AAA 2 26 h323-gw-id 33 Name of the gate way String SIPIDString Start Acc Stop Acc String 80045 67145 Start Acc 30 Called-Station-I ...

  • Nortel Mediant TP-1610 SIP - page 253

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 253 July 2005 K.8 RADIUS Server Messages Note: In Figure K-4 , Figure K-5 and Figure K-6 non-standard parameters are preceded with brackets. K.8.1 Authentication Figure K-4: Authentication Example Access-Request (116) user-name = 111 user-password = (en ...

  • Nortel Mediant TP-1610 SIP - page 254

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 254 Document #: LTRT-72504 12.1.2 Accounting Figure K-6: Accounting Example Accounting-Request (361) user-name = 111 acct-session-id = 1 nas-ip-address = 212.179.22.213 nas-port-type = 0 acct-status-type = 2 acct-input-octets = 4841 acct-output-octets = 8800 acct-session-time = 1 acct-input-packets ...

  • Nortel Mediant TP-1610 SIP - page 255

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 255 July 2005 The user_passwd parameter (that initially containe d the user pa ssword collected from the user) is being assigned the value ‘domain'+user_pa sswd + '.com’. • Calling number (recived form SIP incoming call ) can optionally ...

  • Nortel Mediant TP-1610 SIP - page 256

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 256 Document #: LTRT-72504 K.10 Supported Elements & Attributes Table K-4: VoiceXML Supported Elements & Attributes (continues on pa g es 256 to 260) Element Element’s Description Parameter s Parameter’s D escription Supported name T he name of the modified variable <assign> Assign ...

  • Nortel Mediant TP-1610 SIP - page 257

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 257 July 2005 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa g es 256 to 260) Element Element’s Description Parameter s Parameter’s D escription Supported modal If this is false (the default) all active grammars are turned ...

  • Nortel Mediant TP-1610 SIP - page 258

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 258 Document #: LTRT-72504 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa g es 256 to 260) Element Element’s Description Parameter s Parameter’s D escription Supported label A string which may be used. <log> Generate a debug message expr An ECMAscript expression e ...

  • Nortel Mediant TP-1610 SIP - page 259

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 259 July 2005 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa g es 256 to 260) Element Element’s Description Parameter s Parameter’s D escription Supported finalsilence The interval of silence that indicates end of speec h. ...

  • Nortel Mediant TP-1610 SIP - page 260

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 260 Document #: LTRT-72504 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa g es 256 to 260) Element Element’s Description Parameter s Parameter’s D escription Supported transferaudi o The URI of audio source to play while the transfer attempt is in progress (before far-e ...

  • Nortel Mediant TP-1610 SIP - page 261

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 261 July 2005 8. “Your account number and password do not match”. 9. “We are having technical difficulties, please call agai n later”. 10. “Please enter the number that you wi sh to call followed by the poun d key”. 11. “The number you are ...

  • Nortel Mediant TP-1610 SIP - page 262

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 262 Document #: LTRT-72504 K.11.2 VXML Flow Chart Figure K-7: VXML Script Opening Menu Play VP 1 No No No No No Yes Start No Yes Yes Yes Yes Go To Start Go To 1 Go To 4 Go To St art Go To End Play VP 3 Play VP 4 Play VP 2 Pressed 1? DTMF Pres sed? Pressed 2? Yes Go To 2 Pressed 3? Go To 3 Pressed 4? ...

  • Nortel Mediant TP-1610 SIP - page 263

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 263 July 2005 Figure K-8: VXML Script Option 1, Make a Call No Yes 1 No Yes Yes No No Wa i t s f o r Authentication No Yes Yes Go To 1 Go To T ransf er Go To En d Play VP 5 Play VP 3 Play VP 6 Play VP 3 Play VP 7 Play VP 7 Play VP 4 DTMF Pr essed? DTMF ...

  • Nortel Mediant TP-1610 SIP - page 264

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 264 Document #: LTRT-72504 Figure K-9: VXML Script, Call Transfer Procedure End DTMF Pres sed? No Play VP 3 Yes Play VP 15 Go to Trans fer Call for tr ansfer service Transf er Failed? Play either VP 11, 12 or 13 accordi ng t o Tran sfer fa il u re reason Go to End No No Yes Debit? Final alert time e ...

  • Nortel Mediant TP-1610 SIP - page 265

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 265 July 2005 Figure K-10: VXML Script, Options 2, 3 and 4 2 Play VP 17 Go To St art 3 End Tra nsf er C a ll To an Opera tor 4 End Play VP 16 Figure K-11: VXML Script, Call Termination No End Yes End Play VP 16 Go To Sta rt VXML Scr ipt Term inated? Fre ...

  • Nortel Mediant TP-1610 SIP - page 266

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 266 Document #: LTRT-72504 K.12 VXML Script Example Figure K-12: VXML Script Example (continues on pages 266 to 270) <?xml version="1.0" encoding="UTF-8"?> <vxml version="1.0" application="http://phoenix1.iperia.com:8080/sa3/jsp/sa.jsp"> <var na ...

  • Nortel Mediant TP-1610 SIP - page 267

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 267 July 2005 Figure K-12: VXML Script Example (continues on pages 266 to 270) <if cond="AAStatus==0"> <goto next="#PerformAuthen"/> <else/> <goto next="#PerformTransfer"/> </if> <elseif con ...

  • Nortel Mediant TP-1610 SIP - page 268

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 268 Document #: LTRT-72504 Figure K-12: VXML Script Example (continues on pages 266 to 270) </form> <form id="GetCalledPartyTelephone"> <log label="starting get called party telephone form" cond="'1' == '1'"/> <field name="d ...

  • Nortel Mediant TP-1610 SIP - page 269

    Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 269 July 2005 Figure K-12: VXML Script Example (continues on pages 266 to 270) <param name="password" expr="AuthenticationInfo.user_passwd"/> <nomatch> <prompt> <audio src="/8.wav"> your account and ...

  • Nortel Mediant TP-1610 SIP - page 270

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 270 Document #: LTRT-72504 Figure K-12: VXML Script Example (continues on pages 266 to 270) called transfer failed </audio> </prompt> <goto next="#main_menu"/> <elseif cond="mycall.Result=='busy'"/> <prompt> <audio src="/11.wav" ...

  • Nortel Mediant TP-1610 SIP - page 271

    Mediant 2000 SIP User’s Manual L. SNMP Traps Version 4.4 271 July 2005 Appendix L SNMP T rap s This section provides information on proprietary SNMP traps currently su ppo rted by the gateway. There is a separation bet ween traps that are alar m s and traps that are not (log s). Currently all have the same structu re made up of the same 10 varbin ...

  • Nortel Mediant TP-1610 SIP - page 272

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 272 Document #: LTRT-72504 Table L-2: acBoardConfigurationErr or Alarm Trap Corrective Action: Inspect the run-time specific string to determine the nature of t he configuration err or. Fix the configuration error using t he appr opriate tool: Web interf ace, EMS, or ini file. Save the configuration ...

  • Nortel Mediant TP-1610 SIP - page 273

    Mediant 2000 SIP User’s Manual L. SNMP Traps Version 4.4 273 July 2005 Table L-5: acFeatureKeyError Alarm T rap Condition: After raise Alarm status: Status stays critical until reboot. A clear trap is not sent. Corrective Action: Obtain a corrected feature key from AudioCodes, activa te it by loading to the dev ice, then reset the device. Table L ...

  • Nortel Mediant TP-1610 SIP - page 274

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 274 Document #: LTRT-72504 Table L-8: acBoardOverloadAlarm Ala rm Trap Condition: An overloa d condition exists in one or more of the system components. Alarm Status: Major Condition: T he overload condition passed Alarm Status: Cleared ...

  • Nortel Mediant TP-1610 SIP - page 275

    Mediant 2000 SIP User’s Manual L. SNMP Traps Version 4.4 275 July 2005 L.1.2 Component: AlarmManager#0 Table L-9: acActiveAlarmTableOv erflow Alarm Trap Alarm: acActiveAlarmTableOverflo w OID: 1.3.6.1.4.15003. 9.10.1.21.2.0.12 Default Severity Major Event Ty pe: processingErrorAlarm Probable Cause: resourceAtOrNearingCapacit y (43) Alarm Text: Ac ...

  • Nortel Mediant TP-1610 SIP - page 276

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 276 Document #: LTRT-72504 L.1.4 Other Traps The following are provided as SNMP traps an d are not alarms. Table L-11: coldStart Trap Trap Name: coldStart OID: 1.3.6.1.6. 3.1.1.5.1 MIB SNMPv2-MIB Note: This is a trap from the standar d SNMP MIB. Table L-12: authenticatio nFailure Tra p Trap Name: au ...

  • Nortel Mediant TP-1610 SIP - page 277

    Mediant 2000 SIP User’s Manual M. Regulatory Information Version 4.4 277 July 2005 Appendix M Regulatory Information Declaration of Conformity Application of Council Direc tives : 73/23/EEC (including amendments), 89/336/EEC (including amendments), 1999/5/EC Annex-II of the Directive Standards to which Confor mity is Declared : EN55022: 1998, Cla ...

  • Nortel Mediant TP-1610 SIP - page 278

    Mediant 2000 SIP Mediant 2000 SIP User’s Manual 278 Document #: LTRT-72504 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment technical specif ications. This is confirmed by the registration numbers. The abbreviation, IC, before the registrati on number signifies that regist ration was performed based on ...

  • Nortel Mediant TP-1610 SIP - page 279

    Mediant 2000 SIP User’s Manual M. Regulatory Information Version 4.4 279 July 2005 Original printed on recycled paper and available on CD or Web site ...

  • Nortel Mediant TP-1610 SIP - page 280

    AudioCodes Offices International Headquarte rs AudioCodes Ltd. 1 Hayarden Street, Airport City, Lod 70151, Israel. Tel: +972-3-976 4000 Fax: +972-3-976 4040 Email: info@audiocodes.com USA Headquarters AudioCodes, Inc. 2099 Gateway Place, Suite 500 San Jose, CA 95110 Tel: +1-408-411-1175 Fax: +1-408-451-9520 Email: info@audiocodes.com USA Offices Bo ...

Производитель Nortel Категория Network Router

Документы, которые мы получаем от производителя устройства Nortel Mediant TP-1610 SIP мы можем разделить на несколько групп. Это в частности:
- технические чертежи Nortel
- инструкции обслуживания Mediant TP-1610 SIP
- паспорта изделия Nortel
- информационные брошюры
- энергетические этикетки Nortel Mediant TP-1610 SIP
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Nortel Mediant TP-1610 SIP.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Nortel Mediant TP-1610 SIP, инструкции обслуживания, короткие инструкции или инструкции пользователя Nortel Mediant TP-1610 SIP. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Nortel Mediant TP-1610 SIP.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Nortel Mediant TP-1610 SIP, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Nortel Mediant TP-1610 SIP пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Nortel Mediant TP-1610 SIP.

Полная инструкция обслуживания Nortel, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Nortel Mediant TP-1610 SIP - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Nortel Mediant TP-1610 SIP, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Nortel Mediant TP-1610 SIP, которое найдем в данном документе
3. Советы по использованию основных функций устройства Nortel Mediant TP-1610 SIP - которые должны облегчить нам первые шаги во время использования Nortel Mediant TP-1610 SIP
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Nortel Mediant TP-1610 SIP
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Nortel Mediant TP-1610 SIP в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Nortel Mediant TP-1610 SIP?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Nortel Mediant TP-1610 SIP, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Nortel Mediant TP-1610 SIP со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)