Инструкция обслуживания Cisco Systems 2600

32 страниц 0.34 mb
Скачать

Перейти на страницу of 32

Summary
  • Cisco Systems 2600 - page 1

    1 Cisco IOS Release 12.1(5)T Cisco Hoot and Holler over IP The voi ce multicasting feature on Cisco 2600 and Cisco 3600 series rout ers uses Cisco V oice-ov er -IP (V oIP) technology to creat e a p erman en tly conn ect ed po int-to -mul tipoin t h oot an d holl er netw o rk o v er an IP connection. Four -wire E&M, E1/T1, FX O, and FXS conf igu ...

  • Cisco Systems 2600 - page 2

    Cisco Hoot and Holler over IP Feature Overview 2 Cisco IOS Release 12.1(5)T Hoot and holler is used in these v arious industries as a way to pro vide a one-to -man y or man y-to-m an y conferencing service for v oice commu nications. In the p ast, hoot and holler w as deplo yed using point-to-poin t telco circuits and a hoot an d holler bridging an ...

  • Cisco Systems 2600 - page 3

    Cisco Hoot and Holle r over IP Feature Overview 3 Cisco IOS Release 12.1(5)T Hoot and holler net works are typically spread ov er four to eight sites, although financial retail netwo rks may hav e hundreds of sites interconnected. W ithin a site, bridging (mixing v oice signals) is done locall y with a standard anal og or digital bri dge that may b ...

  • Cisco Systems 2600 - page 4

    Cisco Hoot and Holler over IP Feature Overview 4 Cisco IOS Release 12.1(5)T Figure 2 Hoot and Holler o ver IP us ing Cisco 2600 and Cisco 3600 Ser ies Routers Four -wire E&M, E1/T1, FX O, and FXS conf igurations provide continu ous V oIP connections across a packet netw ork. By using the i nherent point-to -mul tipoint characteristic of IP mc, ...

  • Cisco Systems 2600 - page 5

    Cisco Hoot and Holle r over IP Feature Overview 5 Cisco IOS Release 12.1(5)T IP/TV Access The Cisco Hoot and Holler o ver IP feature enables yo u to access ongoi ng IP/TV multicasts for listening to v oice content of the IP/ TV session. For complete information on IP/TV , see the IP/TV Co ntent Manag er Installation a nd User Guide . Figur e 3 Cisc ...

  • Cisco Systems 2600 - page 6

    Cisco Hoot and Holler over IP Feature Overview 6 Cisco IOS Release 12.1(5)T – The port number mu st be 80, becau se it is HTTP . – Click OK and e xit. Note In the Content Manager , be sure to speci fy the multicast IP addres s and R TP port for the Cisco Hoot and Holl er ov er IP session. Interactive Voi ce Response (IVR) The Cisco Hoot and Hol ...

  • Cisco Systems 2600 - page 7

    Cisco Hoot and Holle r over IP Feature Overview 7 Cisco IOS Release 12.1(5)T Technical Details of the Cisco Hoot and Holler over IP Solution This section describes ho w Cisco Hoot and Holler o v e r IP works from a technical perspecti ve. It co vers design considerat ions in terms of IO S configur ations and DSP mixing funct ionality as well as ban ...

  • Cisco Systems 2600 - page 8

    Cisco Hoot and Holler over IP Feature Overview 8 Cisco IOS Release 12.1(5)T is handled by the onboard DSPs on each voice- card (NM-1V , NM-2V or NM -HD V). Arbitration in volves identifying the v arious so urces of the voice stream, and mixin g inv olves taking some of those voi ce streams and combining them into a si ngle-sourced v oice stream. Ci ...

  • Cisco Systems 2600 - page 9

    Cisco Hoot and Holle r over IP Feature Overview 9 Cisco IOS Release 12.1(5)T The uncompressed bandwidth in cludes IP/UDP/R TP head ers (40 bytes) in the band width calculation. Compressed R TP (cR TP) reduces the IP/UDP/R TP headers to between 2 to 4 byt es per packet. Th e calculation of compressed bandwidth below uses 4 bytes for a compressed IP/ ...

  • Cisco Systems 2600 - page 10

    Cisco Hoot and Holler over IP Feature Overview 10 Cisco IOS Release 12.1(5)T enabled or disabled, b ut since the DSPs also hav e to do arbitration and mixing, V AD mu st be disabled to reduce the DSPs proc essing load. In addition to enabling V A D (which is on b y default) , network administrators should modify the V AD paramet ers that sense b ac ...

  • Cisco Systems 2600 - page 11

    Cisco Hoot and Holle r over IP Feature Overview 11 Cisco IOS Release 12.1(5)T In this ex ample, the digits in th e connection trunk 111 string match the destination pat tern of the V oIP dial peer . Also, the session protocol is set to multicast and th e session target is pointing to the IPmc group number with the UDP port (22222) predef ined. Bene ...

  • Cisco Systems 2600 - page 12

    Cisco Hoot and Holler over IP Supported Platforms 12 Cisco IOS Release 12.1(5)T Supported Platforms Router Platforms: • Cisco 2600 • Cisco 3600 s eries Network Modules: • NM-HD V • NM-1V • NM-2V Supported Standards, MIBs, and RFCs Standards No ne w or modif ied standards are support ed by this featu re. MIBs No ne w or modif ied MIBs are ...

  • Cisco Systems 2600 - page 13

    Cisco Hoot and Holle r over IP Configuration Tasks 13 Cisco IOS Release 12.1(5)T Configuring Multicast Routing (Required) T o enable multicast routing on the pl atform, perform the follo wing steps: Configuring the Virtual Interface (Required) T o configure the v irtual interface fo r multicast fast switching, perform t he follo wing steps: Configu ...

  • Cisco Systems 2600 - page 14

    Cisco Hoot and Holler over IP Configuration Tasks 14 Cisco IOS Release 12.1(5)T Step 5 Router(config-dial-peer)# ip precedence number (Optional) Specifies the IP precedence. Step 6 Router(config-dial-peer)# codec ( codec-type } Conf igures t he codec. Y ou must conf igure the same codec on all dial peers in a session. When the default codec, g729r8 ...

  • Cisco Systems 2600 - page 15

    Cisco Hoot and Holle r over IP Configuration Tasks 15 Cisco IOS Release 12.1(5)T Configuring E&M Voice Ports (Required, if used) If using E&M v oice ports, co nf igure them by p erforming the follo wing steps: Command Purpose Step 1 Router(config)# voice class permanent tag1 Def ines voice class for transmit-receiv e mode. Step 2 Router(con ...

  • Cisco Systems 2600 - page 16

    Cisco Hoot and Holler over IP Configuration Tasks 16 Cisco IOS Release 12.1(5)T Configuring for Receive Only Mode (Optional) T o configure Cisco Hoot and Holler o ve r IP as recei ve-only mod e, perform the follo wing st eps: Configuring Relevant Interfa ce (Serial/Ethernet) (Required) T o configure either the serial or Ethernet interf ace, perform ...

  • Cisco Systems 2600 - page 17

    Cisco Hoot and Holle r over IP Configuration Examples 17 Cisco IOS Release 12.1(5)T Configuring Voice Ports in High-Density Voice Network Modules (Required, if using T1/E1) A multiflex t runk interface car d (NM-HD V) in a high-densit y voice netw ork module requi res special voi ce-port conf iguration when conn ecting for T1/E1 operation. Perform ...

  • Cisco Systems 2600 - page 18

    Cisco Hoot and Holler over IP Configuration Examples 18 Cisco IOS Release 12.1(5)T Note In all of the foll owi ng conf iguration e xamples, th e routers are conf igured wit h an interface vif1 command. This is a virtual interf ace that is similar to a loopback interface—it is a logical IP in terface that is a lways up wh en the router is activ e. ...

  • Cisco Systems 2600 - page 19

    Cisco Hoot and Holle r over IP Configuration Examples 19 Cisco IOS Release 12.1(5)T Note The connection-trunk connecti on type is a point-to-point connection, similar to a tie-line on a PBX network. A ll voi ce traf f ic—including sig naling—placed at one end is immediately transferred to the other . Note The E&M voice port must be conf igu ...

  • Cisco Systems 2600 - page 20

    Cisco Hoot and Holler over IP Configuration Examples 20 Cisco IOS Release 12.1(5)T Verifying the Configuration If you ha ve con figured your routers b y follo wing these e xamples, you shoul d no w be able to talk o ver the telephones. Y ou can also use the show di al -pe er vo ice command on each router to verify that the data you conf igured is c ...

  • Cisco Systems 2600 - page 21

    Cisco Hoot and Holle r over IP Configuration Examples 21 Cisco IOS Release 12.1(5)T Dial peers are identif ied b y numbers, b ut to a vo id confusing these numb ers with telephone numb ers, they ar e usually ref erred to as t ags. Dial peer ta gs are inte gers that can range fro m 1 to 2 31 -1 (2147483647). Dial peers on th e same router must ha v ...

  • Cisco Systems 2600 - page 22

    Cisco Hoot and Holler over IP Configuration Examples 22 Cisco IOS Release 12.1(5)T Voice Multicasting over a WAN The config uration for voice multicasting sessions ov er IP on Frame Relay is the same as for the Ethernet LAN in the pre vious e xample. Conf igure th e W AN interface on each router with the ip address and ip pim sparse-dense-mode comm ...

  • Cisco Systems 2600 - page 23

    Cisco Hoot and Holle r over IP Configuration Examples 23 Cisco IOS Release 12.1(5)T Cisco Hoot and Holler over IP with Ethernet Topology (Two Hoot Groups) Figur e 5 Cisco Hoot and Ho ller o ver I P with Ether net T opology In this conf iguratio n, two hoot and holler grou ps are set up by defi ning two mul ticast groups (237.111.0.111 and 237.111.0 ...

  • Cisco Systems 2600 - page 24

    Cisco Hoot and Holler over IP Configuration Examples 24 Cisco IOS Release 12.1(5)T music-threshold -30 operation 4-wire ! voice-port 1/0/1 voice-class permanent 1 connection trunk 112 music-threshold -30 operation 4-wire ! dial-peer voice 111 voip destination-pattern 111 session protocol multicast session target ipv4:237.111.0.111:22222 ip preceden ...

  • Cisco Systems 2600 - page 25

    Cisco Hoot and Holle r over IP Configuration Examples 25 Cisco IOS Release 12.1(5)T Router-3 (FXO Po rts) hostname Router-3 ! ip multicast-routing ! voice class permanent 1 signal timing oos timeout disabled signal keepalive 65535 ! interface Vif1 ip address 3.3.3.3 255.255.255.0 ip pim sparse-dense-mode ! interface Ethernet0/0 ip address 1.5.13.3 ...

  • Cisco Systems 2600 - page 26

    Cisco Hoot and Holler over IP Configuration Examples 26 Cisco IOS Release 12.1(5)T broadcast-queue is only 40 packet s deep and Cisco Hoot and Holler over IP transmits packets at 50 packets per second. Unless the queue is disabled, so me packets would be dropped and v oice QoS would be degraded. Router-1 hostname Router-1 ! ip multicast-routing ! v ...

  • Cisco Systems 2600 - page 27

    Cisco Hoot and Holle r over IP Configuration Examples 27 Cisco IOS Release 12.1(5)T ip precedence 5 Router-2 hostname Router-2 ! ip multicast-routing ! voice class permanent 1 signal timing oos timeout disabled signal keepalive 65535 ! interface Vif1 ip address 2.2.2.2 255.255.255.0 ip pim sparse-dense-mode ! router rip network 2.2.2.0 network 5.5. ...

  • Cisco Systems 2600 - page 28

    Cisco Hoot and Holler over IP Configuration Examples 28 Cisco IOS Release 12.1(5)T ! interface Vif1 ip address 3.3.3.3 255.255.255.0 ip pim sparse-dense-mode ! router rip network 3.3.3.0 network 5.5.6.0 ! interface Serial0/0 no ip address ip pim sparse-dense-mode encapsulation frame-relay frame-relay traffic-shaping no frame-relay broadcast queue ! ...

  • Cisco Systems 2600 - page 29

    Cisco Hoot and Holle r over IP Command Reference 29 Cisco IOS Release 12.1(5)T Command Reference This section documents a ne w command. Al l other comma nds used with this feature are documented in the Cisco IOS Release 12.1 command reference publications. • session prot ocol multicast ...

  • Cisco Systems 2600 - page 30

    Cisco Hoot and Holler over IP session protocol multicast 30 Cisco IOS Release 12.1(5)T session protocol multicast T o set the session protocol as multicast, use the session pr otocol multicast dial-peer configuration command. T o negate this command and return to the cisco def ault session protocol , use the no vers i on of this command. session pr ...

  • Cisco Systems 2600 - page 31

    Cisco Hoot and Holle r over IP Glossary 31 Cisco IOS Release 12.1(5)T Glossary CIR —Committed information rate. The a verag e rate of information transfer a subscrib er (for example, the network admi nistrator) has st ipulated for a Frame-Relay PVC. Codec —Coder-d ecoder . Devi ce that typical ly uses pu lse-co de modulation (PCM) to transform ...

  • Cisco Systems 2600 - page 32

    Cisco Hoot and Holler over IP Glossary 32 Cisco IOS Release 12.1(5)T VNM —V oice network module. Vo I P —V oice over Internet Protocol. ...

Производитель Cisco Systems Категория Computer Accessories

Документы, которые мы получаем от производителя устройства Cisco Systems 2600 мы можем разделить на несколько групп. Это в частности:
- технические чертежи Cisco Systems
- инструкции обслуживания 2600
- паспорта изделия Cisco Systems
- информационные брошюры
- энергетические этикетки Cisco Systems 2600
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Cisco Systems 2600.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Cisco Systems 2600, инструкции обслуживания, короткие инструкции или инструкции пользователя Cisco Systems 2600. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Cisco Systems 2600.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Cisco Systems 2600, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Cisco Systems 2600 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Cisco Systems 2600.

Полная инструкция обслуживания Cisco Systems, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Cisco Systems 2600 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Cisco Systems 2600, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Cisco Systems 2600, которое найдем в данном документе
3. Советы по использованию основных функций устройства Cisco Systems 2600 - которые должны облегчить нам первые шаги во время использования Cisco Systems 2600
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Cisco Systems 2600
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Cisco Systems 2600 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Cisco Systems 2600?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Cisco Systems 2600, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Cisco Systems 2600 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Комментарии (0)