Инструкция обслуживания GE Monogram 49-90152-1

44 страниц 0.91 mb
Скачать

Перейти на страницу of 44

Summary
  • GE Monogram 49-90152-1 - page 1

    Safety Instr uctions . . . . . . . . . . . 2–5 Operating Instr uctions Controls . . . . . . . . . . . . . . . . . . . . . .6 Cycle Options . . . . . . . . . . . . . . . . . .8 Dryer Features . . . . . . . . . . . . . . . .15 Help . . . . . . . . . . . . . . . . . . . . .13, 14 Loading and Using the Dryer . . . . . . . . . . . . . . . . .16, 17 ? ...

  • GE Monogram 49-90152-1 - page 2

    2 IMPOR T ANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING. WHA T TO DO IF YOU SMELL GAS: Do not try to light a match, or cigarette, or turn on any gas or electrical appliance. Do not touch any electrical switch; do not use any phone in your building. Clear the room, building, or area of all occupants. Immediately call your gas supplier f ...

  • GE Monogram 49-90152-1 - page 3

    3 PROPER INST ALLA TION • Properly ground dryer to conform with all governing codes and ordinances. Follow details in Installation Instructions. • Install or store where it will not be exposed to temperatures below freezing or exposed to the weather . • Connect to a properly rated, protected and sized power supply circuit to avoid electrical ...

  • GE Monogram 49-90152-1 - page 4

    4 WHEN USING YOUR DR YER • Never reach into the dryer while the drum is moving. Before loading, unloading, or adding clothes, wait until the drum has completely stopped. • Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room. DO NOT OPERA TE THE DRYER WITHOUT THE LINT FIL TER IN PLACE. • Do not w ...

  • GE Monogram 49-90152-1 - page 5

    IMPOR T ANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING. 5 READ AND FOLLOW THIS SAFETY INFORMA TION CAREFULL Y . SA VE THESE INSTRUCTIONS. WHEN USING YOUR DR YER (cont.) • Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. ? ...

  • GE Monogram 49-90152-1 - page 6

    Dr yer Control Panel www .GEAppliances.com P O W E R M Y C Y C L E S B A C K H E L P S T ART S TOP H O M E Features of the dr yer control panel 1 POWER. Press to “wake up” the display . If the display is active, press to put the dryer into standby mode. Y ou may also press the T ouch Screen or any button to “wake up” the display . NOTE: Pre ...

  • GE Monogram 49-90152-1 - page 7

    7 Quick Start www .GEAppliances.com Getting Star ted If the T ouch Screen is dark, press POWER or the T ouch Screen to access the dr y cycles menu. Clean the lint filter . IMPORT ANT: Clean the lint filter each time you use the dryer . Add clothes. Do not overload. This wastes energy and promotes wrinkling. Select one of the four drying methods fro ...

  • GE Monogram 49-90152-1 - page 8

    8 Dr y Cycles www .GEAppliances.com Dr ying by Fabric T ype If the T ouch Screen is dark, press POWER or the T ouch Screen to access the dr y cycles menu. The default cycle settings are based on standard load types. Always follow the fabric manufactur er’s care label when laundering. • Blends • Cottons • Delicates • Knits • Polyester ? ...

  • GE Monogram 49-90152-1 - page 9

    9 Summar y Screen www .GEAppliances.com SUMMAR Y SCREEN 0:36 TIME OPTIONS TEMP DR YNESS CYCLE COTTONS MORE DR Y About the Summar y Screen After selecting a dr y cycle, the Summar y Screen displays the automatic settings for the cycle you have chosen. Y ou can adjust these by touching the screen location for any of the settings shown. If you change ...

  • GE Monogram 49-90152-1 - page 10

    Summar y Screen www .GEAppliances.com OPTIONS END OF CYCLE SIGNAL EXTENDED TUMBLE DELA Y ST ART OK 1 HOUR About the Dr ying Options T ouch the OPTIONS pad on the T ouch Screen to select drying options. After selecting any dr ying options, press OK to save your setting. Delay Start T ouch the DELA Y ST ART pad repeatedly to set a delay time of up to ...

  • GE Monogram 49-90152-1 - page 11

    11 “My Cycles” www .GEAppliances.com About the “My Cycles” Feature The “My Cycles” feature allows you to create, store and reuse up to 6 custom cycles. Create your own cycles from scratch or adjust the settings of a predefined dry cycle; then save for one-touch recall. Creating and Using a “My Cycle” Y ou can create “My Cycles” ...

  • GE Monogram 49-90152-1 - page 12

    “My Cycles” www .GEAppliances.com Modifying, Renaming or Deleting a “My Cycle” T o modify the settings of a “My Cycle” from the Home Screen: 1 Press the MY CYCLES button. 2 Select MODIFY from the T ouch Screen menu. 3 Select the cycle name from the T ouch Screen menu. 4 Change any of the automatic settings and select any options. 5 Pres ...

  • GE Monogram 49-90152-1 - page 13

    13 Help www .GEAppliances.com TROUBLE SHOOTER MACHINE PREFERENCES HOME SCREEN HELP About the Help Feature Pressing the HELP button from the Home Screen allows you to locate troubleshooting tips for common dr yer problems, to find help with using the Home Screen or to set machine preferences. Pressing the HELP button while on any other screen allows ...

  • GE Monogram 49-90152-1 - page 14

    The machine settings on the Help feature allow you to control the volume of the button beep and end-of-cycle signal, and turn the washer/dryer communication feature on or off. Press the HELP button, then select from the on-screen options. Button Beep The button beep controls the volume of the beep that is made when you press any of the buttons on t ...

  • GE Monogram 49-90152-1 - page 15

    Changing the Drum Lamp Before replacing the drum lamp, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker . The drum lamp is located at the top left of the door frame. 1 Remove the screw holding the drum lamp shield in place. 2 Slide the shield ...

  • GE Monogram 49-90152-1 - page 16

    16 Loading and Using the Dr yer www .GEAppliances.com Sor ting and Loading Hints As a general rule, if clothes are sorted properly for the washer , they are sorted properly for the dryer . T ry also to sort items according to size. For example, do not dry a sheet with socks or other small items. Do not add fabric softener sheets once the load has b ...

  • GE Monogram 49-90152-1 - page 17

    Dr yer Interior and Duct: The interior of the appliance and exhaust duct should be cleaned once a year by qualified service personnel. The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away f ...

  • GE Monogram 49-90152-1 - page 18

    BEFORE YOU BEGIN Read these instructions completely and carefully . • IMPOR T ANT – Save these instructions for local electrical inspector’ s use. • IMPOR T ANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer . • Note to Consumer – Keep these instructions fo ...

  • GE Monogram 49-90152-1 - page 19

    Installation Instructions 19 UNP ACKING YOUR DR YER T ilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them away from the dryer legs. Be sure to remove all of the foam pieces around the legs. Remove the bag containing the drying rack, literature and serial cable. DRYER DIMENSIONS 27” (68.6 cm) 43 1 ⁄ ...

  • GE Monogram 49-90152-1 - page 20

    20 Installation Instructions LOCA TION OF YOUR DR YER (cont.) REQUIREMENTS FOR ALCOVE OR CLOSET INST ALLA TION • Y our dryer is approved for installation in an alcove or closet, as stated on a label on the dryer back. • The dryer MUST be vented to the outdoors. See the EXHAUST INFORMA TION section. • Minimum clearance between dryer cabinet an ...

  • GE Monogram 49-90152-1 - page 21

    ❒ Flat- or straight-blade screwdriver (may be needed for cord strain relief) ❒ Flexible stainless steel or plastic-coated brass connecting tube (if allowed by building code) ❒ Open-end wrenches for flexible tube and connector ❒ Adjustable pliers (to adjust leveling legs) ❒ Pipe wrench for holding dryer gas inlet while attaching adapter el ...

  • GE Monogram 49-90152-1 - page 22

    22 Installation Instructions GAS REQUIREMENTS W ARNING • Installation must conform to local codes and ordinances, or in their absence, the NA TIONAL FUEL GAS CODE, ANSI Z223. • This gas dryer is equipped with a V alve and Burner Assembly for use only with natural gas. Using conversion kit WE25X10014, your local service organization can convert ...

  • GE Monogram 49-90152-1 - page 23

    Install a 1/8” NPT plugged tapping to the dryer gas line shut-off valve for checking gas inlet pressure. Install a flare union adapter to the plugged tapping. NOTE: Apply pipe compound or T eflon ® tape to the threads of the adapter and plugged tapping. 23 Installation Instructions Attach the flexible metal gas line connector to the adapter . B ...

  • GE Monogram 49-90152-1 - page 24

    CONNECTING A GAS DR YER (cont.) Installation Instructions 24 TEST FOR LEAKS W ARNING – Never use an open flame to test for gas leaks. Check all connections for leaks with soapy solution or equivalent. Apply a soap solution. The leak test solution must not contain ammonia, which could cause damage to the brass fittings. If leaks are found, close t ...

  • GE Monogram 49-90152-1 - page 25

    Installation Instructions 25 TOOLS AND MA TERIALS YOU WILL NEED FOR CONNECTING THE ELECTRICAL SUPPL Y ❒ Flat- or straight-blade screwdriver (may be needed for cord strain relief) ❒ #2 Phillips-head screwdriver (for terminal connections) ❒ UL-listed strain relief (may be supplied with cord) ❒ UL-listed power cord – 30-amp – 240V – #10 ...

  • GE Monogram 49-90152-1 - page 26

    Installation Instructions 26 CONNECTING AN ELECTRIC DR YER (cont.) ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS This dryer must be connected to an individual branch circuit, protected by the required time- delay fuses or circuit breakers. A three- or four -wire, single phase, 120/240V or 120/208V , 60Hz, 30-amp circuit is required. If the electric s ...

  • GE Monogram 49-90152-1 - page 27

    Installation Instructions 27 For 3-wire Connection ONL Y : Be sure the dryer’ s green ground wire is connected to neutral (center) terminal of block and to green ground screw on cabinet rear . D For 4-wire Connection ONL Y : Remove and discard the dryer’ s ground wire between the cabinet and the center of the terminal block. IMPORT ANT : Do NOT ...

  • GE Monogram 49-90152-1 - page 28

    Installation Instructions 28 EXHAUSTING THE DR YER W ARNING – T o reduce the risk of fire or personal injury: • This dryer must be exhausted to the outdoors. • Use only metal duct. • Do not terminate exhaust in a chimney , any gas vent, under an enclosed floor (crawl space) or into an attic. The accumulated lint could create a fire hazard. ...

  • GE Monogram 49-90152-1 - page 29

    Installation Instructions 29 USING FLEXIBLE MET AL DUCT FOR TRANSITION VENTING Rigid or semi-rigid metal ducting is recommended for use as transition ducting between the dryer and the wall. In special installations when it is impossible to make a connection with the above recommendations, then a UL-listed flexible metal transition duct may be used ...

  • GE Monogram 49-90152-1 - page 30

    EQUIV ALENT RIGID NUMBER EQUIV ALENT DUCT PIECES LENGTH X USED = LENGTH Rigid Metal 1 Ft. X (4) = 4 Ft. Ducting (Preferred) Elbows 10 Ft. X (3) = 30 Ft. (90°/45°) T urns Less 2 Ft. X (1) = 2 Ft. Than 4 Ft. Rigid Ducting 1 Ft. X (5) = 5 Ft. 4” W all Cap 5 Ft. X (1) = 5 Ft. T otal Ductwork Length = Ft. TOT AL MUST BE LESS THAN OR EQUAL TO 150 FT ...

  • GE Monogram 49-90152-1 - page 31

    EQUIV ALENT RIGID NUMBER EQUIV ALENT DUCT PIECES LENGTH X USED = LENGTH Rigid Metal 1 Ft. X ( ) = Ft. Ducting (Preferred) Semi-Rigid 25 Ft. X ( ) = Ft. Metal Ducting (inside diameter does not change) Flexible Metal 50 Ft. X ( ) = Ft. Ducting (inside diameter changes) Elbows (90°/45°) 10 Ft. X ( ) = Ft. T urns less 2 Ft. X ( ) = Ft. Than 4 Ft. Rig ...

  • GE Monogram 49-90152-1 - page 32

    Installation Instructions 32 BEFORE YOU BEGIN Remove any lint from the wall exhaust opening. EXHAUSTING THE DR YER (cont.) Internal Duct Opening Wa l l Check that exhaust hood damper opens and closes freely . ST ANDARD REAR EXHAUST We recommend that you install your dryer before installing your washer . This will permit direct access for easier exh ...

  • GE Monogram 49-90152-1 - page 33

    Installation Instructions 33 LEVEL THE DRYER Stand the dryer near the final location. Place a level against the side and bottom of the dryer door frame and use the four leveling legs to level your dryer . Lower Raise A TT ACH SERIAL CABLE Attach the serial cable for washer and dryer connection to the serial port on the back of the dryer . Attach th ...

  • GE Monogram 49-90152-1 - page 34

    Installation Instructions 34 DRYER ST AR TUP Press the POWER button. FINAL SETUP (cont.) P O W E R NOTE: If the dryer has been exposed to temperatures below freezing for an extended period of time, allow it to warm up before pressing POWER. Otherwise, the display will not come on. The dryer will begin a setup mode that tests the dryer’ s operatio ...

  • GE Monogram 49-90152-1 - page 35

    REMOVE FILLER PLUGS Installation Instructions 35 REVERSING THE DOOR SWING (if desired) Open the door and remove the filler plugs opposite the hinges. 1 REMOVE DOOR • With the door completely open, remove the BOTTOM screw from each hinge on the dryer face. • Insert the screws about halfway into the TOP holes, for each hinge, on the opposite side ...

  • GE Monogram 49-90152-1 - page 36

    Installation Instructions 36 REVERSE HANDLE REVERSING THE DOOR SWING (cont.) Install the handle on the opposite side of the door . 5 REMOVE HINGES AND REHANG DOOR Remove the hinges from the door and install them on the opposite side with the hinge pin toward the outside of the door . 6 REMOVE HINGES AND REHANG DOOR (cont.) Insert the door on the op ...

  • GE Monogram 49-90152-1 - page 37

    37 Installation Instructions SWITCHING THE W ASHER AND DR YER BACKSPLASHES (not required for most installations) When viewed from the front, the washer is shipped for installation on the left and the dryer is shipped for installation on the right. If your hose utility connections are arranged so that the units must be installed with the washer on t ...

  • GE Monogram 49-90152-1 - page 38

    38 Installation Instructions DISCONNECT W ASHER CONTROL BOARD Disconnect the ribbon at the right of the control board by pulling the connector at the end of the ribbon off the metal pins on the control board. NOTE: Do not disconnect any other wires from the control board. 3 Rear of W asher REMOVE CONTROL BOARD FROM W ASHER BACKSPLASH Remove the fou ...

  • GE Monogram 49-90152-1 - page 39

    39 Installation Instructions REMOVE CONTROL BOARD FROM DRYER BACKSPLASH Remove the four screws holding the control board to the backsplash. Remove the control board and set it aside. 7 SWITCH BACKSPLASHES Place the backsplash from the dryer on top of the washer and place the backsplash from the washer on top of the dryer . 8 A TT ACH DRYER CONTROL ...

  • GE Monogram 49-90152-1 - page 40

    40 Installation Instructions RECONNECT W ASHER CONTROL BOARD Connect the washer control board to the new backsplash by sliding the ribbon connector on the new backsplash onto the metal pins on the control board and pushing in. Make sure the ribbon is not twisted before inserting the connector . A TT ACH W ASHER CONTROL BOARD TO NEW BACKSPLASH Repla ...

  • GE Monogram 49-90152-1 - page 41

    41 Problem Solver www .GEAppliances.com Problem Possible Cause What T o Do Dr yer won’ t operate Control panel is asleep • This is normal. Press POWER , the touch screen or any button to activate the control panel. Dryer is unplugged • Make sure cord is plugged securely into a working outlet. Controls are not set properly • Make sure the cy ...

  • GE Monogram 49-90152-1 - page 42

    42 Notes www .GEAppliances.com ...

  • GE Monogram 49-90152-1 - page 43

    43 Staple your receipt her e. Proof of the original pur chase date is needed to obtain ser vice under the warranty. For The Period Of: W e Will Replace: One Y ear Any part of the dryer which fails due to a defect in materials or workmanship. During this From the date of the full one-year warranty , GE will also provide, fr ee of charge, all labor a ...

  • GE Monogram 49-90152-1 - page 44

    Consumer Support GE Appliances W eb Site www .GEAppliances.com Have a question or need assistance with your appliance? T r y the GE Appliances W eb site 24 hours a day , any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, order parts, catalogs, or even schedule service on-line. Y ou can also “A ...

Производитель GE Monogram Категория Clothes Dryer

Документы, которые мы получаем от производителя устройства GE Monogram 49-90152-1 мы можем разделить на несколько групп. Это в частности:
- технические чертежи GE Monogram
- инструкции обслуживания 49-90152-1
- паспорта изделия GE Monogram
- информационные брошюры
- энергетические этикетки GE Monogram 49-90152-1
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания GE Monogram 49-90152-1.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа GE Monogram 49-90152-1, инструкции обслуживания, короткие инструкции или инструкции пользователя GE Monogram 49-90152-1. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия GE Monogram 49-90152-1.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства GE Monogram 49-90152-1, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании GE Monogram 49-90152-1 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей GE Monogram 49-90152-1.

Полная инструкция обслуживания GE Monogram, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией GE Monogram 49-90152-1 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания GE Monogram 49-90152-1, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся GE Monogram 49-90152-1, которое найдем в данном документе
3. Советы по использованию основных функций устройства GE Monogram 49-90152-1 - которые должны облегчить нам первые шаги во время использования GE Monogram 49-90152-1
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем GE Monogram 49-90152-1
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра GE Monogram 49-90152-1 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся GE Monogram 49-90152-1?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с GE Monogram 49-90152-1, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с GE Monogram 49-90152-1 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Комментарии (0)