-
Mitsubishi Electronics DX-ZD6UE - page 1
1 HDD Extension Unit INST ALLA TION AND OPERA TION MANUAL MODEL DX-ZD6UE THIS INSTRUCTION MANUAL IS IMPORT ANT T O YOU. PLEASE READ IT BEFORE USING YOUR HDD EXTENSION UNIT . ENGLISH DEUTSCH FRANÇAIS ESP AÑOL IT ALIANO NEDERLANDS ...
-
Mitsubishi Electronics DX-ZD6UE - page 2
2 HEA VY OBJECTS SHOULD NEVER BE PLACED ON THE UNIT (E.G., MONIT OR) NEVER TOUCH OR INSERT ANY OBJECT INSIDE THE UNIT T ouching the inside of the cabinet or inserting foreign objects of any kind through the ventilation holes not only creates a safety hazard but can also cause extensive damage. PROTECT THE POWER CORD Damage to the power cord may cau ...
-
Mitsubishi Electronics DX-ZD6UE - page 3
ENGLISH 3 The HDD and cooling fan of this unit are driving parts. For stable recording, it is recommended that both of these parts are replaced every 30,000 hours. (This interval is for reference purpose only and does not indicate the warranty period of the parts.) MAINS LEAD CONNECTION The mains lead on this Unit is fitted with a non-rewireable m ...
-
Mitsubishi Electronics DX-ZD6UE - page 4
4 W arning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Important safeguards ................................................... i-iv Caution and care .............................................................. 2 Features ......... ...
-
Mitsubishi Electronics DX-ZD6UE - page 5
ENGLISH 5 1 2 3 4 1 POWER indicator When the EXTERNAL CONTROL switch is set to OFF or it is set to ON with the connected recorder turned on, this indicator illuminates while the MAIN switch on the rear panel is turned on. 2 HDD1, HDD2 indicators (ACCESS indicators) While HDD 1 or HDD 2 is being accessed, the corresponding indicator momentarily blin ...
-
Mitsubishi Electronics DX-ZD6UE - page 6
6 TEMP ALM terminal T erminal for informing of high internal temperature. F AN ALM terminal T erminal for informing of abnormality of the fan. HDD ALM terminal T erminal for informing of abnormality of the HDD. 4 EXTERNAL CONTROL switch Set this switch to ON (left side) to turn on and off the power of this unit linking with the recorder ’s switch ...
-
Mitsubishi Electronics DX-ZD6UE - page 7
ENGLISH 7 Notice • It is impossible to supply 5V DC power from this port. • Do not connect any devices other than DX-ZD6UE to these output ports. ...
-
Mitsubishi Electronics DX-ZD6UE - page 8
8 Connections Connectable recorders MITSUBISHI DIGIT AL RECORDER • DX-TL5000 series (DX-TL5000U, DX-TL5000E, DX-TL5000UA, DX-TL5000E400, DX-TL5000E(Z)) • DX-TL4500 series (DX-TL4516E, DX-TL4516E(Z), DX-TL4516U, DX-TL4509E, DX-TL4509E(Z), DX-TL4509U) The above stated models are connectable as of October 2007. Consult your dealer for the connecti ...
-
Mitsubishi Electronics DX-ZD6UE - page 9
ENGLISH 9 Precautions for connection Notice • When connecting 5 or more HDD extension units (with 2 HDDs mounted on each unit) to the digital recorder , you are recommended to use USB cable as illustrated below to prevent recognition error of digital recorder due to different start-up times among HDDs. Furthermore, before you start operation or w ...
-
Mitsubishi Electronics DX-ZD6UE - page 10
10 Startup Step 1 T urn ON the MAIN switch on the rear of this unit. Step 2 T urn on the MAIN switch on the rear of the recorder . • The POWER indicator of this unit illuminates when the power supply of this unit is not linked with the recorder . Step 3 After “POWER OFF” is displayed on the LCD of the recorder , press the POWER button on the ...
-
Mitsubishi Electronics DX-ZD6UE - page 11
ENGLISH 1 1 Setting the ID number of this unit Step 1 T urn OFF the MAIN switch on the rear of this unit. Step 2 Remove the cover of this unit according to steps 1 to 3 of “Removing the HDD” on page 14. • The ID number is set using the ID rotary switch inside the cover . ID rotary switch ＜ Inside the front cover ＞ Step 3 Set the ID rotary ...
-
Mitsubishi Electronics DX-ZD6UE - page 12
12 HDD operation mode This unit has 2 HDD operation modes as described below . Spanning mode This mode regards and uses 2 built-in HDDs as 1 HDD. The total data capacity of 2 HDDs is available. Notice • When either of the HDDs fails in the spanning mode, both of the HDDs become unusable and the recorded data are deleted. Mirroring mode T h i s m ...
-
Mitsubishi Electronics DX-ZD6UE - page 13
ENGLISH 13 Step 7 Attach the cover of this unit according to steps 9 to 1 1 of “Attaching the HDD” on page 17. Step 8 T urn ON the MAIN switch on the rear of the unit. ...
-
Mitsubishi Electronics DX-ZD6UE - page 14
14 Replacing the HDD Precautions for replacing the HDD W ARNING • Do not remove the top cover of the unit. Notice • Before you replace the HDD, read "Important safeguards" on pages i to iv and "Caution and Care" on pages 2 and 3 again. • Do not attach or remove the HDD unnecessarily . Attaching or removing the HDD of this ...
-
Mitsubishi Electronics DX-ZD6UE - page 15
ENGLISH 15 Step 4 Disconnect 2 cords connected to the circuit board on the metal part. Step 5 Remove the metal part. • Remove 4 screws on the metal part. Step 6 Pull out the HDD tray halfway . HDD 1 HDD 2 Step 7 Remove the cords. Notice • Because S-A T A connectors of HDD are very delicate, connect or disconnect the cords gently without applyin ...
-
Mitsubishi Electronics DX-ZD6UE - page 16
16 Attaching the HDD Notice • Whe n yo u at tach mul tipl e HD Ds, atta ch t hem in the order of HDD 1 and 2. Step 1 Attach the new HDD onto the HDD tray with 4 screws. • Make s ure to at tach the HDD in t he correc t orienta tion. Notice • When attaching the HDD to this unit, use the supplied screws. Step 2 Insert the HDD tray halfway . Step ...
-
Mitsubishi Electronics DX-ZD6UE - page 17
ENGLISH 17 Step 9 Attach the front covers. • Attach the left cover first and push it to the left. • Then, attach the right cover . Step 10 Fix the front covers with 2 screws. Step 1 1 C l o s e t h e s c r e w c o v e r s o n b o t h s i d e s o f t h e cover . Tips • Follow the same procedures to attach or remove HDD 2. ...
-
Mitsubishi Electronics DX-ZD6UE - page 18
18 No No No No No Y es Y es Y es Mirroring Spanning Y es Y es Y es Both indicators of HDD 1 and HDD 2 illuminate red. Both indicators of HDD 1 and HDD 2 blink red. Is the operation mode set to spanning or mirroring? Is the operation mode set to mirroring? Either indicator of HDD 1 or HDD 2 illuminates red. Is the MODE rotary switch set correctly? I ...
-
Mitsubishi Electronics DX-ZD6UE - page 19
ENGLISH 19 T roubleshooting If problems with the unit persist even after you followed the suggestions below , please stop using the unit, disconnect the power cord and contact the retailer from whom you purchased the unit. Please check the following Description of problem • Is the power cord properly plugged in? • Is the EXTERNAL CONTROL switch ...
-
Mitsubishi Electronics DX-ZD6UE - page 20
20 Specifications General Rated Power Supply: 100 to 240 V AC, 50/60 Hz Rated Input: 0.75 - 0.4 A (100-240 V) Operating T emperature: 41 °F-104 °F (5 °C to 40 °C) Relative Humidity: Max. 80 (%) Altitude: Max. 2000 (m) Dimensions: 424 (Width) x 361 (Depth) x 49 (Height) (mm) Weight: 6.3 kg (with 2 HDD mounted) Control terminals CONT IN Input te ...
-
Mitsubishi Electronics DX-ZD6UE - page 21
IT AL Y Mitsubishi Electric Europe B.V . Italian Branch Of fi ce Centro Direzionale Colleoni Palazzo Perseo - Ingresso 2, Via Paracelso 12, 20041 Agrate Brianza, Italy T elephone: +39 (039)-605 31 Fax: + 39 (039)-605 3214 The Netherlands Mitsubishi Electric Benelux A Division of Mitsubishi Electric Europe B.V . Niiverheidsweg 23A, 3641 RP Mijdrech ...
У вас вопрос, касающийся Mitsubishi Electronics DX-ZD6UE?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Mitsubishi Electronics DX-ZD6UE, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Mitsubishi Electronics DX-ZD6UE со всей вероятностью он захочет поделиться методом ее решения.