Инструкция обслуживания Chamberlain ATS 2113X

32 страниц 1.36 mb
Скачать

Перейти на страницу of 32

Summary
  • Chamberlain ATS 2113X - page 1

    Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System ® is connected and properly aligned. ■ Periodic checks of the opener are required to ensure safe operation. ■ The model number label is ...

  • Chamberlain ATS 2113X - page 2

    2 Introduction 2-5 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning .....................................................................4 Carton inventory ....................... ...

  • Chamberlain ATS 2113X - page 3

    3 T o prevent damage to garage door and opener: • AL W A YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJUR Y OR DEA TH: • AL W A YS call a trained door systems technician if garage door binds, sticks, or is out of ...

  • Chamberlain ATS 2113X - page 4

    Safety Re versing Sensor Horizontal and vertical reinforcement is needed for lightw eight garage doors (fiberglass, steel, aluminum, door with glass panels , etc.). See page 18 for details . Suppor t brac ket & fastening hardw are is required. See page 1 1. — — — — — — — — Header W all Safety Rev ersing Sensor Gap between floor ...

  • Chamberlain ATS 2113X - page 5

    5 Straight Door Arm Door Bracket Plate Door Bracket Safety Labels and Literature "C" Wrap (2) 2 -Conductor Bell Wire White & White/Red Curved Door Arm Rail Styrofoam Chain Pulley Bracket Trolley Chain Safety Reversing Sensor Mounting Bracket With Slot (2) Safety Reversing Sensor Mounting Bracket With Square Holes (2) Mounting Hardware ...

  • Chamberlain ATS 2113X - page 6

    6 ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Place the opener on packing material to protect the cover . • Remove the (2) 5/16"-18x1/2" washered bolts mounted in the top of the motor unit. • Position rail at a 45˚ angle to op ...

  • Chamberlain ATS 2113X - page 7

    7 ASSEMBL Y STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain from twisting. • When the chain is approximately 1/2" (1.27 cm) above the base of the rail at its midpoint, re-tight ...

  • Chamberlain ATS 2113X - page 8

    8 INST ALLA TION STEP 1 Determine the Header Bracket Location 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket within 4 feet (1.22 m) of the left or right of the door center only if a torsion spring or center bearing plate is in ...

  • Chamberlain ATS 2113X - page 9

    9 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HEA ...

  • Chamberlain ATS 2113X - page 10

    10 Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Chain Pulley Bracket Temporary Support Header Wall Garage Door Rail Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Chain Pulley Bracket Rail HARDW ARE SHOWN ACTUAL SIZE INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage f ...

  • Chamberlain ATS 2113X - page 11

    11 INST ALLA TION STEP 4 Position the Opener SECTIONAL DOOR ONL Y A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 laid flat on the top section beneath the rail. T rolley ...

  • Chamberlain ATS 2113X - page 12

    12 Drywall Anchors Insulated Staples Screw 6ABx1-1/2" Lighted Door Control Button HARDW ARE SHOWN ACTUAL SIZE T o prevent possible SERIOUS INJUR Y or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires. T o prevent possible SERIOUS INJUR Y or DEA TH from ...

  • Chamberlain ATS 2113X - page 13

    13 INST ALLA TION STEP 7 Install the Light • Install a 75 watt maximum light bulb in the socket. The light will turn O N and remain lit for approximately 4-1/2 minutes when power is connected. Then the light will turn OFF . • If the bulb burns out prematurely due to vibration, replace with a “Garage Door Opener” bulb. NOTE: Use only standar ...

  • Chamberlain ATS 2113X - page 14

    14 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, co ...

  • Chamberlain ATS 2113X - page 15

    15 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direct ...

  • Chamberlain ATS 2113X - page 16

    16 Inside Garage Wall “C” Shaped Wrap Mounting Bracket with Square Holes 1/4-20x1/2" Carriage Bolts 1/4"-20 Lock N uts Drill 3/8" Holes Garage Door Track Figure 3 Garage DOOR Track Installation Mounting Bracket With Square Holes #10-32x3/8" Screws “C” Wrap #10-32 Lock N uts Figure 1 Garage WALL or DOOR Track Installation ...

  • Chamberlain ATS 2113X - page 17

    17 Hex Bolt 1/4-20 x 1-1/2" "C" Wrap Sensor with Wire Wing N ut Indicator Light Figure 6 Invisible Light Beam Protection Area Sensor Sensor Connect Wire to Opener Terminals Bell Wire Bell Wire Finished Ceiling Sensor Connections Wall Control Connections (dotted line) OPENER TERMINAL SCREWS 1 2 3 Figure 7 MOUNTING AND WIRING THE SAFET ...

  • Chamberlain ATS 2113X - page 18

    If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes for the door bracket, fasten as shown in Figure 2. INST ALLA TION STEP 11 Fasten the Door Bracket A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should cover the height of the top panel. The ...

  • Chamberlain ATS 2113X - page 19

    19 INST ALLA TION STEP 12 Connect Door Arm to T rolley SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from the door) about 2" (5 cm) as shown in Figures 1, 2 and 3. • Figure 1: – Fasten straight do ...

  • Chamberlain ATS 2113X - page 20

    20 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not rev ...

  • Chamberlain ATS 2113X - page 21

    ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather ...

  • Chamberlain ATS 2113X - page 22

    Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested every month. • If one control (for ce or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...

  • Chamberlain ATS 2113X - page 23

    OPERA TION Using Y our Garage Door Opener Y our opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. Activate your opener with any of the following: • The hand-held Remote Control: Hold the large push button down until the door starts to move. • The wall-mounted Door Control: Hold th ...

  • Chamberlain ATS 2113X - page 24

    24 T o Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually . T o reconnect the door to the opener , press the door control push bar . The lockout feature prevents the trolley from reconnecting automatically . Pull the emergency release handle down and back (toward ...

  • Chamberlain ATS 2113X - page 25

    25 Having a Problem? 1. The opener doesn’t operate from either the Door Control or the remote control: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn’t light, check the fuse box or the circuit breaker . (Some outlets are controlled by a wall switch.) • Have you disabled all door locks? Review installation in ...

  • Chamberlain ATS 2113X - page 26

    26 The 300 Series remote control works only with door openers and light controls having a purple “Learn” button. Programming instructions are described and illustrated below . The additional push buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those access ...

  • Chamberlain ATS 2113X - page 27

    27 1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button. 3. Release the button when the motor unit lights blink. It has learned the code. ...

  • Chamberlain ATS 2113X - page 28

    28 Multi-Function Door Control (Optional) OPERA TION OF THE MUL TI-FUNCTION DOOR CONTROL Press the push button to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it’s opening. Light feature Press the Light button to turn the opener light on or off. It will not control the opener lights w ...

  • Chamberlain ATS 2113X - page 29

    6 UP CEILING MOUNT ONL Y 10 1 N O TIC E 3 5 4 9 8 11 12 2 7 29 2 1 3 4 5 Installation Parts REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A2780 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 CD1008 8 Foot (2.44 m) Rail Assy . CD1010 10 Foot (3.05 m) Rail Assy . CD1012 12 Foot (3.66 m) Rail ...

  • Chamberlain ATS 2113X - page 30

    30 Motor Unit Assembly Parts 9 7 12 13 14 15 18 4 8 11 17 10 16 3 5 6 18 15 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 1 2 KEY P ART NO. NO. DESCRIPTION 1 41C5069 Rail support bracket assembly kit 2 41B4569 Pulley (Chain) 3 41A5668 Gear and sprocket assembly . Complete with: ...

  • Chamberlain ATS 2113X - page 31

    31 ACCESSORIES LOCK LIGHT 370LM CD1008 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 8 Foot (2.44 m) Complete Rail: T o allow an 8 foot (2.44 m) door to open fully . 10 Foot (3.05 m) Complete Rail: T o allow a 10 foot (3.05 m) door to op ...

  • Chamberlain ATS 2113X - page 32

    © 2006, The Chamberlain Group, Inc. 1 14A3155D All Rights Reserved LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SIX DA YS A WEEK. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Std. Time) 6:00 A.M. TO 7:00 P .M. - Monday thro ...

Производитель Chamberlain Категория Garage Door Opener

Документы, которые мы получаем от производителя устройства Chamberlain ATS 2113X мы можем разделить на несколько групп. Это в частности:
- технические чертежи Chamberlain
- инструкции обслуживания ATS 2113X
- паспорта изделия Chamberlain
- информационные брошюры
- энергетические этикетки Chamberlain ATS 2113X
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Chamberlain ATS 2113X.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Chamberlain ATS 2113X, инструкции обслуживания, короткие инструкции или инструкции пользователя Chamberlain ATS 2113X. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Chamberlain ATS 2113X.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Chamberlain ATS 2113X, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Chamberlain ATS 2113X пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Chamberlain ATS 2113X.

Полная инструкция обслуживания Chamberlain, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Chamberlain ATS 2113X - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Chamberlain ATS 2113X, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Chamberlain ATS 2113X, которое найдем в данном документе
3. Советы по использованию основных функций устройства Chamberlain ATS 2113X - которые должны облегчить нам первые шаги во время использования Chamberlain ATS 2113X
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Chamberlain ATS 2113X
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Chamberlain ATS 2113X в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Chamberlain ATS 2113X?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Chamberlain ATS 2113X, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Chamberlain ATS 2113X со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Комментарии (0)