-
Vermont Casting 1990 - page 1
Homeowner ’ s Installation and Operating Manual For use in the United States and Canada Do Not Discard This Manual: Retain for Future Use 2000966 2/07 Rev . 19 The Intrepid II W oodburning Stove Model 1990 SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERL Y INST ALLED, OPERA TED AND MAIN- T AINED, A HOUSE FIRE MA Y RESUL T . TO REDUCE THE RISK OF F ...
-
Vermont Casting 1990 - page 2
2 Intrepid II W oodb ur ning Stove 2000966 W elcome All of us at CFM Corporation Ask your V ermont Castings dealer how these instal- lation accessories can enhance the versatility , ap- pearance, and safety of your Intrepid Stove. 0307 Bottom Heat Shield 0172 Rear Heat Shield Chimney connector heat shields Heavy-gauge enamel pipe to match the stove ...
-
Vermont Casting 1990 - page 3
3 Intrepid II W oodb ur ning Stove 2000966 Specifications Intrepid II, Model 1990 21 " (545 mm) 20" (510 mm) 25 " (640 mm) T op exit flue collar height 21 " (540 mm) 24" (610 mm) 7 " (180 mm) 21 " (545 mm) C L 21 " (540 mm) 18" (460 mm) 1 ? ...
-
Vermont Casting 1990 - page 4
4 Intrepid II W oodb ur ning Stove 2000966 Installation SAFETY NOTICE: IF YOUR STOVE IS NOT PROP- ERL Y INST ALLED, A HOUSE FIRE MA Y RESUL T . TO REDUCE THE RISK OF FIRE, FOLLOW THE INST AL- LA TION INSTRUCTIONS. CONT ACT LOCAL BUILD- ING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INST ALLA TION INSPECTION REQUIREMENTS IN YOUR AREA. Before you begin ...
-
Vermont Casting 1990 - page 5
5 Intrepid II W oodb ur ning Stove 2000966 If you use an existing masonry chimney , it must be inspected to ensure safe condition before the stove is installed. Y our local professional chimney sweep, build - ing inspector , or fire department official will be able to inspect the chimney or provide a referral to someone who can. The chimney must ...
-
Vermont Casting 1990 - page 6
6 Intrepid II W oodb ur ning Stove 2000966 Keep the horizontal run of chimney connector as short and direct as possible, with no more than two 90° turns. Slope horizontal runs of connector upward 1/4” per foot (20mm per m) going from the stove toward the chim- ney . The recommended maximum length of a horizontal run is 3’ (914mm). The recommen ...
-
Vermont Casting 1990 - page 7
7 Intrepid II W oodb ur ning Stove 2000966 The opening through the chimney wall to the flue (the “breach”) must be lined with either a ceramic or metal cylinder , called the “thimble”, which is cemented firmly in place. The fit must be snug and the joint between the thimble and the chimney wall must be cemented. (Fig. 6) A special piece ...
-
Vermont Casting 1990 - page 8
8 Intrepid II W oodb ur ning Stove 2000966 Fireplace Chimney Installations - Through a Fireplace If your fireplace height is at least 25” (635mm), you may install an Intrepid II with standard legs through the fireplace opening using a “positive connection” kit available from your local dealer . These positive connec- tion kits ensure a tigh ...
-
Vermont Casting 1990 - page 9
9 Intrepid II W oodb ur ning Stove 2000966 Y our local dealer or your local building inspector can provide details for other approved methods of passing a chimney connector through a combustible wall in your area. In Canada, this type of installation must conform to CAN/CSA-B365, Installation Code for Solid Fuel Burning Appliances and Equipment. T ...
-
Vermont Casting 1990 - page 10
10 Intrepid II W oodb ur ning Stove 2000966 Floor Protection for Fireplace Installations Do not assume your fireplace hearth is completely noncombustible. Many fireplace hearths do not satisfy the “completely noncombustible” requirement because the brick or concrete in front of the fireplace opening is supported by heavy wood framing as in F ...
-
Vermont Casting 1990 - page 11
1 1 Intrepid II W oodb ur ning Stove 2000966 connector) and nearby shields carries away heat. Do not block the air flow by filling this empty space with any insulating material. The shiny shield surface facing the heat source must be left unpainted, enabling it to reflect heat back towards the stove or connector and away from the wall. Shields a ...
-
Vermont Casting 1990 - page 12
12 Intrepid II W oodb ur ning Stove 2000966 Noncombustible shields installed 1” (25 mm) away from the combustible surface on noncombustible spacers, called ventilated shields, may be used to reduce clear- ances. (Fig. 14) 1" (25mm) 1/4" (6mm) ST501 mantel and trim shield 11/10/00 djt ST501 Fig. 14 A custom-formed mantel shield. ...
-
Vermont Casting 1990 - page 13
13 Intrepid II W oodb ur ning Stove 2000966 ST503 Alcove side view 1 1/10/00 djt Metal Stud Combustible facing may overlap metal studs by only 1” 1” air gap top and bottom, on both sides and back wall 7/16” Durock® (or equivalent) Joist Shield (Sup- plied by Chimney Manufacturer) ST503 Fig. 17 Alcove side section. St504 Alcov e cutawa y? ...
-
Vermont Casting 1990 - page 14
14 Intrepid II W oodb ur ning Stove 2000966 Intrepid II Clearance Chart See Pages 15 and 16 for illustrations of these clearances. * Clearances with double-wall connectors and protected surfaces have not been tested for the Intrepid II. 1. Shielding for a top exit stove must include the stove rear heat shield insert to protect the area behind the ? ...
-
Vermont Casting 1990 - page 15
15 Intrepid II W oodb ur ning Stove 2000966 D E F F C C A B J K L L I I G H ST507 Intrepid Clearance Diagrams 11/00 P Q M N Intrepid II Clearance Diagrams See the chart on Page 14 for dimensions indicated by letter in the diagrams below . Stove Installed Parallel to W all Stove in Corner Stove Installed Parallel to W all Protected Surface ...
-
Vermont Casting 1990 - page 16
16 Intrepid II W oodb ur ning Stove 2000966 W all Shield Requirements for Some Common Intrepid II Installations IN T R E PI D II C C C C D F A B E D ST508 Intrepid II wall shield 1 1/00 ST508 Fig. 21 Parallel installation, vertical chimney connector , two wall shields. Reduced clearances for both rear and side walls. W all shields may meet at corne ...
-
Vermont Casting 1990 - page 17
17 Intrepid II W oodb ur ning Stove 2000966 Distance from the Center of the Flue Collar to the W all in T op-Exit Installations The information on this page is helpful in planning stove placement for top-exiting installations, particularly those in- stallations with chimneys that pass through the ceiling. However , this is not a clearance chart. Fi ...
-
Vermont Casting 1990 - page 18
18 Intrepid II W oodb ur ning Stove 2000966 Clean the Griddle Before Use At the factory the griddle is coated with vegetable oil to prevent rusting while the stove is in transit and storage. Remove the oil with a dry rag or paper towel before you use the stove. Set Up the Stove Remove any loose parts from inside the stove. Place a protective pad on ...
-
Vermont Casting 1990 - page 19
19 Intrepid II W oodb ur ning Stove 2000966 ST515 reverse flue collar 1 1/17/00 djt Flue Collar Screws ST515 Fig. 30 Reversing the flue collar . Attach the Griddle Handle Install the handle on the griddle. Place the griddle upside down at the edge of a flat surface and assemble the handle as shown. (Fig. 31) With the handle pointing 45° from ...
-
Vermont Casting 1990 - page 20
20 Intrepid II W oodb ur ning Stove 2000966 A Damper Directs Air Flow Within the Stove The damper handle opens and closes the damper to direct air flow within the stove, and is next to, and to the right of, the primary air control lever on the right side of the stove. (Fig. 34) When the handle points to the floor , the damper is open, letting smo ...
-
Vermont Casting 1990 - page 21
21 Intrepid II W oodb ur ning Stove 2000966 W ARNING: For safety and greatest efficiency , oper- ate your stove only with all doors/griddles fully closed. The test standard for your stove when it is operated in this mode is UL 1482. Y our stove may be used as a fireplace with the front doors open or removed only when the spark screen is placed co ...
-
Vermont Casting 1990 - page 22
22 Intrepid II W oodb ur ning Stove 2000966 Use the Air Control Settings that Work Best for Y ou No single air control setting will fit every situation. Set- tings will differ depending on the quality of the fuel, the amount of heat desired, and how long you wish the fire to burn. The control setting also depends on your particular installation? ...
-
Vermont Casting 1990 - page 23
23 Intrepid II W oodb ur ning Stove 2000966 produce soot or large flakes of char or fly ash that can coat the combustor and cause smoke to spill into the room. Coal smoke also can poison the catalyst so that it won’t operate properly . In general, the fire must be sufficiently well-established to ensure catalytic activity is initiated. When ? ...
-
Vermont Casting 1990 - page 24
24 Intrepid II W oodb ur ning Stove 2000966 Continue adding split logs of this size to the briskly- burning fire until there is a glowing ember bed at least 3” (75mm) deep. A good ember bed is neces- sary for proper functioning of the catalytic system and may take an hour or more to establish. 5. Close the damper when the griddle temperature rea ...
-
Vermont Casting 1990 - page 25
25 Intrepid II W oodb ur ning Stove 2000966 A stove is part of a system, which includes the chimney , the operator , the fuel, and the home. The other parts of the system will affect how well the stove works. When there is a good match between all the parts, the system works well. Wood stove operation depends on natural (unforced) draft. Natural dr ...
-
Vermont Casting 1990 - page 26
26 Intrepid II W oodb ur ning Stove 2000966 Creosote Creosote is a by-product of slow wood-burning. It’s an organic tar that can condense in the flue if it’s dense in the smoke, and slow-moving, and cools off to less than 290°F . Condensed creosote is volatile, and can generate chimney fires if it gets hot enough. All the features that affec ...
-
Vermont Casting 1990 - page 27
27 Intrepid II W oodb ur ning Stove 2000966 Maintenance Let the fire in the stove go out and allow the stove to cool completely before beginning any maintenance procedure. Care of the Cast Iron Surface An occasional dusting with a dry rag will keep the painted cast iron of your Intrepid looking new . The stove’s paint can be touched up as needed ...
-
Vermont Casting 1990 - page 28
28 Intrepid II W oodb ur ning Stove 2000966 ST532 damper adj 11/00 Thermostat Cover D-plate Damper Actuator Rod Handle Damper Locking Nut Allen Head Ad - justment Screw ST532 Fig. 45 T ighten the damper adjustment screw for a snug seal. How to Adjust the Door Latch Over time, the gasketing around the doors will com- press, and the latch may n ...
-
Vermont Casting 1990 - page 29
29 Intrepid II W oodb ur ning Stove 2000966 The Catalytic Combustion System Inspection and Cleaning This wood heater includes a catalytic combustor , which needs periodic inspection and replacement for proper operation. In the United States, it is against the law to operate this wood heater in a manner inconsistent with the operating instructions i ...
-
Vermont Casting 1990 - page 30
30 Intrepid II W oodb ur ning Stove 2000966 6. Remove the damper housing. It is held in place by two weld screws and two chrome acorn nuts in the back of the stove. Loosen the chrome acorn nuts and rotate the tabs to release the damper housing. Y ou may find it necessary to remove or loosen the thermostat cover to access the one of acorn nuts inst ...
-
Vermont Casting 1990 - page 31
31 Intrepid II W oodb ur ning Stove 2000966 5. Lay an unbroken 1/8” (3mm) bead of gasket cement in the newly-cleaned channel. Starting at one end, press the gasket into the channel. Ensure a good joint where the gasket meets before trimming any excess. Do not overlap the gasket ends or leave ends with ragged edges. 6. Press the gasketed part fir ...
-
Vermont Casting 1990 - page 32
32 Intrepid II W oodb ur ning Stove 2000966 • Inspect and clean the catalytic block, and vacuum out the ash at the bottom of the back plate after removing the lower fireback. Lightly clean the refrac- tory assembly that houses the element. Be careful not to damage the refractory material, which is very fragile. • Inspect the secondary probe th ...
-
Vermont Casting 1990 - page 33
33 Intrepid II W oodb ur ning Stove 2000966 Appendix: Catalytic Combustor In any chemical reaction, including the combustion process, there are certain conditions which must be met before the reaction can take place. For example, a reaction may require a certain temperature, or a certain concentration of the reactants (the combustion gases and oxyg ...
-
Vermont Casting 1990 - page 34
34 Intrepid II W oodb ur ning Stove 2000966 1 2 3 4 5 6 7 8 9 10 12 13 16 17 18 20 9 21 22 25 26 24 23 21 36 37 38 39 40 41 15 1 1 12 9 42 43 43 27 28 29 30 31 32 33 35 34 0966 Intrepid II exploded view 1 1/00 22a 73 0966 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and prod ...
-
Vermont Casting 1990 - page 35
35 Intrepid II W oodb ur ning Stove 2000966 45 46 47 48 49 50 57 52 53 54 60 57 59 68 65 64 63 62 44 55 56 66 67 61 58 51 0966 Intrepid II exploded view 8/02 72 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. Item Description Part Numbe ...
-
Vermont Casting 1990 - page 36
36 Intrepid II W oodb ur ning Stove 2000966 Stove Serial No. _____________________ Dealer ____________________________ __________________________________________ __________________________________________ Phone _____________________________ Date Purchased _____________________ Installer ___________________________ __________________________________ ...
-
Vermont Casting 1990 - page 37
37 Intrepid II W oodb ur ning Stove 2000966 ...
-
Vermont Casting 1990 - page 38
38 Intrepid II W oodb ur ning Stove 2000966 ...
-
Vermont Casting 1990 - page 39
39 Intrepid II W oodb ur ning Stove 2000966 W arranty Limited 3 Y ear W arranty CFM Corporation warrants that this woodburning stove will be free of de- fects in material and workmanship for a period of three years from the date you receive it, except that the catalyst, thermostat assembly , handles, glass door panels, cement, and gasketing shall b ...
-
Vermont Casting 1990 - page 40
© CFM Corporation 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www .cfmcorp.com CFM Corporation ...
У вас вопрос, касающийся Vermont Casting 1990?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Vermont Casting 1990, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Vermont Casting 1990 со всей вероятностью он захочет поделиться методом ее решения.