-
Rosewill RC403 - page 1
PCI 56Kbps V .92 Data/fax V oice Modem Car d RC403 User Manual ...
-
Rosewill RC403 - page 2
1 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 Installation Guide Installation Guide for Windows Series 98/98SE/ME/2000 and XP . ........................................2 System Requirements ...................................................................................................... 2 Modem Installation................... ...
-
Rosewill RC403 - page 3
2 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 Installation Guide for Windows Series 98/98SE/ME/2000 and XP System Requir ements • Computer with Pentium 200 MMX or higher processor . • Windows 98/98SE/ME/2000 and XP Operating System. • 20 MB Hard Disk fr ee space or above • Sound card for voice featur es • 1 available PCI ...
-
Rosewill RC403 - page 4
3 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 Basic A T Command Guide T - Set T one Dial Default This command forces DTMF dialing until the next P dial modifier or P command is r eceived. The modem will set an S-Parameter bit to indicate that all subsequent dialing should be conducted in tone mode. Note that the DP command will o ...
-
Rosewill RC403 - page 5
4 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 Result Codes OK <value> = 0 or 1. ERROR Otherwise. O - Return to On-Line Data Mode This command specifies that the modem will enter the on-line data mode from the on-line command mode with or without a retrain. If in the of f-line command mode when this command is entered, the m ...
-
Rosewill RC403 - page 6
5 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 &V - Display Current Configuration and Stor ed Profile This command reports the curr ent (active) configuration and the stored (user) profiles. Syntax &V Result Code OK Example: A T&V ACTIVE PROFILE: E1 L1 M1 Q0 T V1 X0 &C1 &D2 &G0 &T0 S00:000 S01:000 S0 ...
-
Rosewill RC403 - page 7
6 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 the *B command. The format of the response is shown by the example below (delay times ar e shown as hours:minutes:seconds). If no numbers are delayed, only the OK r esult code is issued. Example: NO. - PHONE NUMBER -DELA Y ------ ------------------------------------------- 1; 826473466 ...
-
Rosewill RC403 - page 8
7 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 state of a negotiated handshake with a V .92-compliant server in V .92 Mode. Syntax +PMH=<value> Defined V alues <value> Decimal number corresponding to the selected operation. 0 Modem-on-hold enabled in V .92 Mode. (Default.) 1 Disabled modem-on-hold. Result Codes OK 0 or ...
-
Rosewill RC403 - page 9
8 User Manual PCI 56Kbps V .92 Data/fax V oice Modem Card RC403 13 Grant MOH with indefinite timeout Result Codes OK 0-13 in V .92 Mode (+MS=V92) ERROR Otherwise Reporting Current or Selected V alues Command: +PMHT? Response: +PMHT : <value> Example: +PMHT : 0 For the default setting. Reporting Supported Range of Parameter V alues Command: + ...
