-
Omega IP710 SERIES - page 1
U ser ’ s Guide IP710 SERIES I/P Conver ters Shop online at omega.com e-mail: info@omega.com For latest product manuals: omegamanual.info ...
-
Omega IP710 SERIES - page 2
Servicing Nor th America: USA: One Omega Drive, P .O. Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 F AX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada TEL: (514) 856-6928 F AX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: S ...
-
Omega IP710 SERIES - page 3
W ARRANTY / DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months fro m d ate of pu rcha se. OMEGA ’ s W ARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA ’ s c ...
-
Omega IP710 SERIES - page 4
Page 1 1 .00 25.4 2.94 74.7 1 2 3.69 93.7 2.18 55.4 .125 3.17 .500 12.7 1.80 45.7 1.30 33.0 1.50 38.1 Mounting Holes #10 –32 UNF –2B X 3/8 Deep 2 Places 22 GA. wire leads approx. 18" long pos, neg, grd In and out ports 1/4 –20 NPT 4 places 1.13 28.7 3.12 79.2 .516 13.1 .383 9.72 ...
-
Omega IP710 SERIES - page 5
DANGER, W ARNING, CAUTION and NOTE statements R efers to conditions or hazards which could result in serious personal injury or death. Refers to conditions or hazards which could result in personal injury . Refers to conditions or hazards which could result in equipment or proper ty damage. Alerts you to facts or special instructions. ALL DANGER, W ...
-
Omega IP710 SERIES - page 6
1. DESCRIPTION and INST ALLA TION 1.1 Description 1.1.1 The Omega IP710 converts a curr ent input signal to a linearly proportional pneumatic output pressur e. This unit utilizes a closed loop pressur e feedback system that closely controls output and compensates for vibration, mounting angle, temperature and supply pr essure variations. The contr ...
-
Omega IP710 SERIES - page 7
Figure 3 - DIN 43650 Connector DIN Rail mounting kit IP610-DM 1.4 Pneumatic Connections 1.4.1 Clean all pipe lines to remove dirt and scale befor e installation. 1.4.2 Supply air must be filtered to 40 micr ons and free of moistur e and lubricants. 1.4.3 The 1/4” NPT inlet and outlet connections ar e labeled on the body . Plug all unused ports wi ...
-
Omega IP710 SERIES - page 8
1.6 Factory Mutual Research Corporation (FM) and Canadian Standards association (CSA) Factory Mutual and Canadian Standards Association I.S. Installation Drawing Notes: 1. Control equipment connected to the Associated Apparatus must not use or generate mor e than 250 V rms or Vdc. 2. The IS Barriers or Equipment (Associated Apparatus) must be FM Ap ...
-
Omega IP710 SERIES - page 9
2. OPERA TION 2.1 Calibration 2.1.1 All units ar e shipped from the factory calibrated, direct acting. 2 .1.2 If the user r equires a differ ent mode of operation (i.e. reverse acting, split range) it is necessary to r eposition inter- n al electrical switches as indicated below . Though the units are factory calibrated for direct acting it is sugg ...
-
Omega IP710 SERIES - page 10
2.3 Reverse Acting Calibration 2.3.1 When calibrated to operate in the r everse acting mode the minimum input signal produces the maximum output pressur e and increasing the input signal r esults in decreasing the output pressur e. Setting the unit to operate in the reverse acting mode is accomplished by positioning internal electrical switches. Do ...
-
Omega IP710 SERIES - page 11
Page 8 3. MAINTENANCE AND REP AIRS U nder normal circumstances, no maintenance should be required. 3.1 Cleaning 3.1.1 If clean, dry air is not used the orifice can become blocked. T o clear , first tur n off supply air , then remove the screw located under the zer o adjustment. The orifice is located between the two black o-rings. Y ou may need a m ...
-
Omega IP710 SERIES - page 12
M-4063/ 0 3 0 7 Where Do I Find Ever ything I Need for Pr ocess Measurement and Contr ol? OM EGA…Of Course! Shop online at www .omega.com TEMPERA TURE M U Thermocouple, R TD & Thermistor Probes, Connectors, Panels & Assemblies M U W ire: Thermocouple, R TD & Thermistor M U Calibrators & Ice Point References M U Recorders, Contr ol ...
