Deutsch dropdown-ico

Bedienungsanleitung Weider WESY29520

34 Seiten 2.63 mb
Download

Zur Seite of 34

Summary
  • Weider WESY29520 - page 1

    USER'S MANUAL CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY29520 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under seat) Visit our website at www .weiderfitness.com new products, prizes, fitness tips ...

  • Weider WESY29520 - page 2

    2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASSEMBL Y . . . . . . . . . . . . . . . . . . . ...

  • Weider WESY29520 - page 3

    3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only . ...

  • Weider WESY29520 - page 4

    4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 77 in. Width: 81 in. Length: 59 in. Foot Plate Low Pulley Station Ab Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arm Press Arm Weight Seat Seat Backrest Backrest Leg Press Plate Thank you for selecting the versatile WEIDER ® PRO 3200 weight system. The PRO 3200 weight system offer ...

  • Weider WESY29520 - page 5

    26 5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. • T ighten all parts as you assemble them, unless instructed to do otherwise. • ...

  • Weider WESY29520 - page 6

    6 4. Press a 2” x 2 1/2” Inner Cap (22) into the top of the Right Leg (73). Press a 1 1/2” Square Inner Cap (41) into the Right Upright (6). Attach the Right Upright (6) to the Right Base (1) with the two indicated 5/16” x 2 1/2” Carriage Bolts (57) and two 5/16” Nylon Locknuts (71). Attach the Bumper (25) to the Right Leg (73) with the ...

  • Weider WESY29520 - page 7

    7 7. Set two Weight Bumpers (83) over the indicated holes in the Center Base (67). Insert the two Weight Guides (20) into the holes. Attach the Weight Guides to the Center Base with two 5/16” x 2 3/4” Bolts (60), four 5/16” W ashers (26), and two 5/16” Nylon Locknuts (71). 26 26 26 26 73 71 6 5 59 59 71 5 71 71 83 83 26 26 26 60 26 67 20 7 ...

  • Weider WESY29520 - page 8

    8 10. Press a 2” x 2 1/2” Inner Cap (22) into the end of the Right T op Frame (8). Attach the Right T op Frame (8) to the Right Upright (6) with two 5/16” x 3 1/4” Bolts (59), a Support Plate (21), and two 5/16” Nylon Locknuts (71). Attach the Right T op Frame (8) to the Left T op Frame (3) with two 5/16” x 2 3/4” Bolts (60), two 5/16 ...

  • Weider WESY29520 - page 9

    9 13. Lubricate a 3/8” x 2” Bolt (62) with grease. Attach the Pivot Bracket (48) to the Right Butterfly Arm (1 1) with the Bolt and a 3/8” Nylon Jamnut (50). Do not overtighten the Locknut; the Pivot Bracket must be able to pivot easily . Press a 1 1/2” x 2” Inner Cap (23) into the indicat- ed end of the Right Butterfly Arm (1 1). Wet the ...

  • Weider WESY29520 - page 10

    10 16. Press a 2” x 2 1/2” Inner Cap (22) into the top of the Leg Press Frame (30). Lubricate a 3/8” x 3” Bolt (61) with grease. Attach the Leg Press Frame (30) to the Left Base (2) with the Bolt and a 3/8” Nylon Locknut (70). Do not overtighten the Locknut; the Leg Press Frame must be able to pivot easily . 14. Lubricate a 3/8” x 3” ...

  • Weider WESY29520 - page 11

    11 20. Note: The following drawings are shown from the left side of the weight system, with the Left T op Frame (3) removed for clarity . Wrap the High Cable (45) around a 3 1/2” Pulley (38). Attach the Pulley at the rear hole, inside of the bracket on the Center T op Frame (14) with a 3/8” x 1 3/4” Bolt (66) and a 3/8” Nylon Locknut (70). ...

  • Weider WESY29520 - page 12

    12 23. Locate the Leg Press Cable (95). Attach the Cable inside the Left Leg (36) with a 3/8” x 2 3/4” Bolt (81), two 3/8” W ashers (75), two Long Spacers (80), and a 3/8” Nylon Locknut (70). 24. Wrap the Leg Press Cable (95) around a 3 1/2” Pulley (38). Attach the Pulley inside the Leg Press Frame (30) with a 3/8” x 2 3/4” Bolt (81), ...

  • Weider WESY29520 - page 13

    13 27. Remove the preattached 3 1/2” Pulley (not shown) from the “U”-Bracket (85). Attach the end of the Leg Press Cable (95) to the “U”-Bracket (85) with a 1/4” W asher (35) and a 1/4” Nylon Locknut (65). Note: Do not complete- ly tighten the Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the ins ...

  • Weider WESY29520 - page 14

    14 31. Wrap the Butterfly Cable (46) around a “V”-Pulley (39). Attach the Pulley and a Long Cable Trap (40) to the bracket on the Right Upright (6) with a 3/8” x 2 1/2” Bolt (63) and a 3/8” Nylon Locknut (70). Be sure the Cable T rap is turned to hold the Cable in the groove of the Pulley . 32. Attach the Butterfly Cable (46) to the Pivot ...

  • Weider WESY29520 - page 15

    15 35. Route the Leg Lever Cable (96) through the Right Upright (6) and around a 3 1/2” Pulley (38). Attach the Pulley and a Cable T rap (91) to the Upright with a 3/8” x 3 3/4” Bolt (84), a 3/8” W asher (75), and a 3/8” Nylon Locknut (70). 36. Wrap the Leg Lever Cable (96) around a 3 1/2” Pulley (38). Attach the Pulley to the Double ? ...

  • Weider WESY29520 - page 16

    16 39. Route the Low Cable (47) through the Left Leg (36) and the Left Upright (7). Attach a 3 1/2” Pulley (38) inside the Upright with a 3/8” x 2 3/4” Bolt (81), two 3/8” W ashers (75), two 1/2” Spacers (34), and a 3/8” Nylon Locknut (70). 40. Wrap the Low Cable (47) around a 3 1/2” Pulley (38). Attach the Pulley and a Cable Trap (91 ...

  • Weider WESY29520 - page 17

    17 41. Wrap the Low Cable (47) around a 3 1/2” Pulley (38). Attach the Pulley to the indicated bracket on the Left Base (2) with a 3/8” x 2” Bolt (62) and a 3/8” Nylon Locknut (70). 43. Wrap the Low Cable (47) around a 3 1/2” Pulley (38). Attach the Pulley and a Cable Trap (91) to the second set of holes from the bottom of the indicated A ...

  • Weider WESY29520 - page 18

    18 45. Wrap the Low Cable (47) around a 3 1/2” Pulley (38). Attach the Pulley to the indicated bracket on the Right Base (1) with a 3/8” x 2” Bolt (62) and a 3/8” Nylon Locknut (70). 47. Wrap the Low Cable (47) around a 3 1/2” Pulley (38). Attach the Pulley and a Cable Trap (91) to the side of the Right Upright (6) with a 3/8” x 3 3/4? ...

  • Weider WESY29520 - page 19

    19 50. Press two 3/4” x 1 1/2” Inner Caps (103) and a 1 1/4” Square Inner Cap (104) into the Adjustable Backrest Frame (100). Attach a Backrest (15) to the Adjustable Backrest Frame (100) with four 1/4” x 3/4” Bolts (13). Insert the Adjustable Backrest Frame (100) into the Right Upright (6) and secure it with an Adjustment Knob (101). Att ...

  • Weider WESY29520 - page 20

    This section explains how to adjust the weight system. See the EXERCISE GUIDELINES on page 26 for impor- tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise. Make sure all parts are properly tightened each time the weight system is us ...

  • Weider WESY29520 - page 21

    21 TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. See drawing A. Slack can be removed by moving the 3 1/2” Pulley (38) and Cable T rap (91) to a higher set of holes in the adjustab ...

  • Weider WESY29520 - page 22

    22 53 6 CONVERTING THE BUTTERFL Y ARMS T o use the Butterfly Arms (10, 1 1) as butterfly arms, insert the Locking Pins (53) into the butterfly holes in the Right Upright (6). T o use the Butterfly Arms (10, 1 1) as press arms, insert the Locking Pins (53) into the press holes in the Butterfly Frame (9). Make sure that the Locking Pins (53) are full ...

  • Weider WESY29520 - page 23

    23 WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each exercise station. “T op” refers to the 6 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. Weight resistance shown for the butterfly arm sta- tion is for each butterfly arm. Note: The actual resistance at each station may vary due to ...

  • Weider WESY29520 - page 24

    High Cable (45) CABLE DIAGRAMS The cable diagrams below show the proper routing of the High Cable (45), the Butterfly Cable (46), the Low Cable (47), the Leg Press Cable (95), and the Leg Lever Cable (96). Use the diagrams to make sure that the cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, ...

  • Weider WESY29520 - page 25

    25 4 1 2 5 2 1 3 5 Leg Lever Cable (96) Leg Press Cable (95) 3 4 CABLE ID CHART — (46) 47 3/7” — (96) 97 3/4” — (95) 148 1/4” — (47) 276 3/4” — (45) 1 16 3/4” ...

  • Weider WESY29520 - page 26

    26 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise. Y ou can adjust the intensity level of an individual exercise in two w ...

  • Weider WESY29520 - page 27

    27 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout. Plan to spend the first couple of weeks familiarizing yourself wit ...

  • Weider WESY29520 - page 28

    ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (WESY29520) 2. The NAME ...

  • Weider WESY29520 - page 29

    This chart is provided to help you identify the small parts used in assembly . The number in parenthesis below each part refers to the key number of the part from the P ART LIST in the center of this manual. Important: Some parts may have been pre-assembled for shipping. If you cannot find a part in the parts bags, check to see if it has been pre-a ...

  • Weider WESY29520 - page 30

    3/8" Nylon Locknut (70) 3/8" Nylon Jamnut (50) 1/4" W asher (35) 1" Round Inner Cap (24) 1 1/2" x 2” Inner Cap (23) 2" x 2 1/2” Inner Cap (22) 2" Square Inner Cap (33) 3/4" Round Inner Cap (27) 3/8" W asher (75) 5/16" W asher (56) 1/4" Nylon Locknut (65) 5/16" Nylon Locknut (71) 1 1/2& ...

  • Weider WESY29520 - page 31

    3/8" x 5 1/2" Bolt (58) 3/8" x 1 3/4" Bolt (66) 3/8" x 2" Bolt (62) 3/8" x 2 1/2" Bolt (63) 3/8" x 3" Bolt (61) 3/8" x 3 3/4" Bolt (84) 3/8" x 3" Button Head Bolt (97) 5/16" x 2 1/2" Carriage Bolt (57) 5/16" x 1" Shoulder Bolt (78) #8 x 3/4" Screw (68) 1/ ...

  • Weider WESY29520 - page 32

    8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE ...

  • Weider WESY29520 - page 33

    Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY29520 R1002A 1 1 Right Base 2 1 Left Base 3 1 Left T op Frame 4 1 Leg Lever 5 1 Right Seat Frame 6 1 Right Upright 7 1 Left Upright 8 1 Right T op Frame 9 1 Butterfly Frame 10 1 Left Butterfly Arm 1 1 1 Right Butterfly Arm ...

  • Weider WESY29520 - page 34

    2 7 62 71 60 67 5 15 16 39 39 40 41 40 71 71 71 71 71 63 63 70 70 26 1 28 38 57 71 70 57 71 71 60 71 60 38 47 57 70 57 13 71 38 70 62 21 59 8 22 53 54 54 9 97 97 61 70 68 22 54 55 54 55 50 50 60 71 60 62 33 82 32 71 81 75 80 71 71 70 71 70 70 58 71 26 26 26 26 26 83 26 71 26 26 65 65 19 11 12 23 46 48 62 78 71 50 64 64 76 10 12 19 46 48 62 78 64 50 ...

Produzent Weider Kategorie Home Gym

Dokumente, die wir vom Produzenten des Geräts Weider WESY29520 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Weider
- Bedienungsanleitungen WESY29520
- Produktkarten Weider
- Informationsbroschüren
- oder Energieetiketten Weider WESY29520
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Weider WESY29520.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Weider WESY29520, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Weider WESY29520. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Weider WESY29520 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Weider WESY29520, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Weider WESY29520 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Weider WESY29520 verständlich ist.

Eine gänzliche Bedienungsanleitung von Weider sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Weider WESY29520 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Weider WESY29520 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Weider WESY29520, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Weider WESY29520 - die uns die ersten Schritte während der Nutzung von Weider WESY29520 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Weider WESY29520 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Weider WESY29520 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Weider WESY29520?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Weider WESY29520 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Weider WESY29520 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)