Bedienungsanleitung Bloomfield 9454

30 Seiten 1.52 mb
Download

Zur Seite of 30

Summary
  • Bloomfield 9454 - page 1

    721 OWNERS M A NUAL for POST-MIX DISPENSERS MODELS : 9454 9456 Includes: Installation Operation Use & Care Servicing Instructions p/n 83188 Rev. C ECN- 12 738 M 721 04 0811 cps Model 9456 3-Flavor Dispenser ...

  • Bloomfield 9454 - page 2

    NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1. VISIBLE LOSS OR DA M AGE: Be certain that any ...

  • Bloomfield 9454 - page 3

    MODEL STYLE VOLT S WAT TS AMP S 1ø POWER SUPPLY CORD 9454 2-FLAVOR 120 VAC 1ø 1500 W 12.5A 9456 3-FLAVOR NEMA 5-15P 1 TABLE OF CONTENTS SPECIFIC ATIONS Thank You for pu rchasing th is Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance w ill ensure that it gives you the very be ...

  • Bloomfield 9454 - page 4

    FE AT U R E S AN D OP E R AT I N G CO N T R O L S 2 ...

  • Bloomfield 9454 - page 5

    FEATURES AND OPER ATING CONTROLS (continued) 3 ITEM DESCRIPTION COMMENTS 1 WA TE R TA NK 2 WATER LEVEL PROBES SENSE HIGH AND LOW WATER LEVE LS 3 DISPENSER W ATER SUPPLY TUBES 9456 SHOWN. FOR 9454, CENTER TUBE I S BLANKED 4 WATER TANK FILL TUBE 5 VENT / OVERFLOW 6 HEATING ELEMENT 1500 W ATT ELEMENT TO HEAT W ATER IN TANK 7 DRAIN FITTING DRAIN W ATER ...

  • Bloomfield 9454 - page 6

    FEATURES AND OPERATING CONTROLS (continued) 4 INTERNAL COMPONENTS ITEM DESCRIPTION COMMENTS 30 W HIPPER MOTORS 31 AUGER MOTOR 32 VENT "TEE" 33 DISPENSE SOLENOIDS 34 TEMPERATURE CONTROL THERMOSTAT CONTROLS HEATING ELEMENT 35 HI-LIMIT THERMOSTAT OVER-TEMP PROTECTION 36 W ATER FILL SOLENOID SUPPLIES W ATER TANK 37 COLD W ATER "TEE" ...

  • Bloomfield 9454 - page 7

    PRECAUTIONS A ND GENERAL INFORM A TION 5 WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which requ ire the use of tools. Failure to heed this warning can result in electrical s hock. WARNING: INJURY HA ZARD All installation pro ...

  • Bloomfield 9454 - page 8

    INSTALL ATION 6 RE A D THIS CAREFULL Y BEFORE ST A RTING TH E INST A LLA TION Unpack the unit. Inspec t all com ponents for completeness and condition. Ensure that all packing materials have been removed from the unit. Read all instructions in this m anual carefully before st arting installation of this f ryer. READ AND UNDE RSTAND ALL LABELS AND D ...

  • Bloomfield 9454 - page 9

    INSTALLATION (continued) 7 WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide suc h a ground . Electrical shock will cause death or serious injury. IMPORTANT: Supply power mu st match nameplate for voltage and phase. Connecting to the wrong voltage will damage the brew ...

  • Bloomfield 9454 - page 10

    OPERATION 8 OPERATING MODES IMPORTANT: Dispensers used to dispense both hot and cold drinks, must be connected to a co ld wat erline . Portab l e un its ha ve no mean s of providing t wo diff erent wa ter tem per atures, INITIAL SET-UP: WATERLINE-CONNECTED DISPENSERS 1. Turn POWER switch OFF . Turn W ATERLINE / PORTABLE switch to WATE RLI NE Turn H ...

  • Bloomfield 9454 - page 11

    OPERATION (continued) 9 INITIAL SET-UP: PORTABLE DISPENSERS 1. Turn PO W ER switch OFF . Turn W ATERLINE / PORTABLE switch to PORTABLE Turn HE ATER switch OFF . Turn COLD/HOT / HOT/HOT switch to HOT/HOT Turn DISPE NSE / FLUSH switch to flush 2. Add water to tank. NOTE: To avoid an overflow when the water bottle is installed, f ill only until water ...

  • Bloomfield 9454 - page 12

    OPERATION (continued) NOTE : Hoppers and motors for various products are essenti ally identical. In a cold / hot dispensing mode, the cold product must be placed in the left dispen ser only . Otherwise, product m ay be place d in and dispen sed fr om either hopper. SUGGESTION : For eas y identification of the hopper contents, a 2” strip o f “fr ...

  • Bloomfield 9454 - page 13

    CLEANING I NSTRUCTIONS PROCEDURE: Daily Cleaning - Dispenser PRECAUTIONS: Avoid spla shing hot water f rom tank FREQUENCY: Daily TOOLS: Mild Detergent, Clean So ft Cloth or S ponge 1. Open f ront door. Turn the DISPENSE / FLUSH switch to the FLUSH position 2. Place a large cup under the right dispensing spout. Press and hold the left dispense butto ...

  • Bloomfield 9454 - page 14

    CLEANING I NSTRUCT IONS (continued) 12 PROCEDURE: Weekly Cleaning & Sanitizing PRECAUTIONS: Disconnect disp enser fro m electric pow er and allo w to cool. Av oid splashing hot water f rom tank FREQUENCY: Weekly TOOLS: Small Flat-Blade Screwdriver Bott le Brush of Stiff Bristle Brush Mild D etergent, Clean Sof t Cloth or Sponge 1. Disconnect di ...

  • Bloomfield 9454 - page 15

    CLEANING INSTRUCTIONS (continued) 13 PROCEDURE: Weekly Cleaning - Hoppers PRECAUTIONS: None FREQUENCY: Weekly, or as necessary TOOLS: Mild Detergent, Clean Soft Cloth or Sponge 1. W hen refilling hopper, insp ect auger spring, star wheel and inside of hopper for a "crusty" buildup. 2. W hen nece ssa ry, disassemble hopper and w ash all pa ...

  • Bloomfield 9454 - page 16

    TROUBLESHOOTING SUGGEST IONS 14 CAUTION: SHOCK HA ZA RD Opening access panels may expose un insulated electrical components. Disconnect dispenser from electrical pow e r before removing any panel. Do not attempt to repair or replace components without first unplugging the pow er cord. Use caution when adjusting water flow rates or testing voltages ...

  • Bloomfield 9454 - page 17

    TROUBLESHOOTING SUGGESTIONS (continued) 15 PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION WATER DRIPS OR FLOWS OUT SPOUT WITH POWER OFF Foreign particles inside dispense valve Remove valve coil, gently lif t off valve dome and diaphragm, clean diaph ragm Torn diaphragm in dispenser valv e Replace diaphragm Defective dispense valve Replace dispense valve ...

  • Bloomfield 9454 - page 18

    SERVICING INSTRUCTIONS 16 CAUTION: SHOCK HAZARD Opening access pan els may expose uninsu lated electr ical components. Disconnect dispenser f rom electrical power before removing any panel. Do not attemp t to repair or replace components without first unplugging the po wer cor d . Use caution when adjusting water flow rates or testing voltages with ...

  • Bloomfield 9454 - page 19

    SERVICING INSTRUCTIONS 17 COLD WATE R A DJUSTMENT The dispenser can dispense both hot and cold beverage on ly when connected t o a wat er line with the water suppl y valve open. Cold product is available from the left dispenser only, and only when the COLD/HOT, HOT/ HO T selector switch is set in COLD/HOT position. 1. Unplug po wer cord. 2. Remove ...

  • Bloomfield 9454 - page 20

    SERVICING INSTRUCT IONS (continued) 18 REPLACE PRODUCT DELIVERY AUGER Before at tempting majo r changes, such a s installi ng a diff erent rate product delivery auger, consult your product supplier for recommendations as to the required ratio product weight per volume of water. See th e char t belo w for auger spring delivery rates. p/n PRODUCT DEL ...

  • Bloomfield 9454 - page 21

    SERVICING INSTRUCTIONS (continued) 19 CAUTION: CHEMICA L BU RN HA ZA RD Deliming chemicals may be caustic. Wear appropriate protective gloves and goggles during this procedur e. Never siphon deliming chemicals or solutions by mouth. This operation sh ou ld on l y be performed by qualified and experienced service personnel. IMPORTANT: DO NOT spill, ...

  • Bloomfield 9454 - page 22

    EXPLODED VIEWS 20 ...

  • Bloomfield 9454 - page 23

    EXPLODED VIEWS (continued) 21 ...

  • Bloomfield 9454 - page 24

    EXPLODED VIEWS (continued) 22 ...

  • Bloomfield 9454 - page 25

    EXPLODED VIEWS (continued) 23 ...

  • Bloomfield 9454 - page 26

    EXPLODED VIEWS (continued) 24 ...

  • Bloomfield 9454 - page 27

    25 SERVICE PARTS LIST Nut w/ Lockwasher S0311 Nut, Nylon 1/2-13 S0313 Nut, Hex SS 6-32 x 5/15 S0316 Nut, NS 4-40 SS S0343 Screw SS 6-32 x 1/4 S0434 Screw SS 6-32 x 3/8 S0435 Screw SS 10-32 x 3/8 S0444 Washer SS .187 ID S0514 Washer SS .500 ID S0518 Washer Nylon .171 ID S0536 Panel Assy, Left Side S10036 Bracket, Vac (Model 9454) S10060 Harness LNC/ ...

  • Bloomfield 9454 - page 28

    WIRING DIA GRAM 26 9454 ...

  • Bloomfield 9454 - page 29

    WIRING DIA GRAM 27 9456 ...

  • Bloomfield 9454 - page 30

    Bloo mf iel d Indu st ri es, Inc . Division of Carrier Co mmercial Refrigeration In US and Can ada T elep h one: 775 -689- 5700 Fa x: 888 -492- 2783 Fa x: 800 -356- 5142 () websi te: www . wells bl oomfi eld. c om fo r order s onl y Bloomf i eld I ndust r ies p r oudly suppor ts CFESA Commerc ial Fo od Equ ipment Servi ce Associ a tio n ...

Produzent Bloomfield Kategorie Beverage Dispenser

Dokumente, die wir vom Produzenten des Geräts Bloomfield 9454 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Bloomfield
- Bedienungsanleitungen 9454
- Produktkarten Bloomfield
- Informationsbroschüren
- oder Energieetiketten Bloomfield 9454
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Bloomfield 9454.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Bloomfield 9454, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Bloomfield 9454. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Bloomfield 9454 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Bloomfield 9454, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Bloomfield 9454 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Bloomfield 9454 verständlich ist.

Eine gänzliche Bedienungsanleitung von Bloomfield sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Bloomfield 9454 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Bloomfield 9454 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Bloomfield 9454, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Bloomfield 9454 - die uns die ersten Schritte während der Nutzung von Bloomfield 9454 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Bloomfield 9454 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Bloomfield 9454 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Bloomfield 9454?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bloomfield 9454 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bloomfield 9454 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)