Deutsch dropdown-ico

Bedienungsanleitung Philips TDA5360

34 Seiten 0.14 mb
Download

Zur Seite of 34

Summary
  • Philips TDA5360 - page 1

      TDA5360 Pre–Amplifier for Hard Disk Drive with MR-Read / Inductive W rite Heads Objective specification, Revision 2.2 1998 Jul 30 INTEGRA TED CIRCUITS ...

  • Philips TDA5360 - page 2

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 2 1 FEATURES 2 APPLICATIONS 3 QUICK REFERENCE DATA 4 DESCRIPTION 5 ORDERING INFORMATION 6 BLOCK DIAGRAM 7 PINOUT DIAGRAM 8 PIN DESCRIPTIONS 9 FUNCTIONAL DESCRIPTION 9.1 ACTIVE READ MODE 9.2 ACTIVE ...

  • Philips TDA5360 - page 3

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 3 1 FEATURES • 12 channels design for Single-stripe (SAL and GMR) Read / Thin-film Write heads. • Design target 350 Mbps, for d=0 (16 / 17) rate code. • Differential Hybrid sense Reader archi ...

  • Philips TDA5360 - page 4

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 4 3 QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT V CC DC Supply voltage +4.5 +5 +5.5 V V EE -4.5 -5 -5.5 V NF Noise Figure Note 3, Section 14 1.7 1.7 dB IRNV Input Referred ...

  • Philips TDA5360 - page 5

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 5 4 DESCRIPTION The +/- 5.0 volt pre-amplifier for HDD described here has been designed for 12 terminals, comprised of a SAL or GMR magneto-resistive reader and an inductive thin film writer. In re ...

  • Philips TDA5360 - page 6

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 6 6 BLOCK DIAGRAM HEADMUX d/dt Av MUX SERIAL INTERFACE FAULT DETECTION BUFFER MR BIAS / POWER SETTING WRITE BANDGAP THERMAL ASPERITY DETECTOR RDp RDn FLT Rext WDp WDn SDATA SCLK SEN + CURRENT RFE h ...

  • Philips TDA5360 - page 7

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 7 7 PAD ARRANGEMENT Fig.2 TDA5360 pad arrangement pads up. WN11 WP11 RP11 RN11 RN10 RP10 WP10 WN10 WN9 WP9 RP9 RN9 RN8 RP8 WP8 WN8 VEE WN4 WN5 WN6 WP5 RP5 RN5 RN4 RP4 WP4 VCC WN7 WP7 RP7 RN7 RN6 RP ...

  • Philips TDA5360 - page 8

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 8 8 PAD DESCRIPTION SYMBOL Pin Description VCC +5V supply GND Ground VEE -5V supply RDP,RDN output Read Data, Differential read signal outputs RWN logic input Read/Write : read = HIGH, write = LOW ...

  • Philips TDA5360 - page 9

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 9 9 FUNCTIONAL DESCRIPTION 9.1 Active READ mode Taking RWN high and programming bits MODE0 and MODE1 (see Reg.09) selects the read mode. The Head select inputs, in serial register, select the appro ...

  • Philips TDA5360 - page 10

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 10 9.2 Active WRITE mode Taking RWN low from an Active READ mode selects the Active WRITE mode. The head select inputs, in a serial register, select the appropriate head. In write mode the circuit ...

  • Philips TDA5360 - page 11

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 11 9.5 SLEEP mode The sleep mode is selected by programming bits MODE0 and MODE1. (see Reg.09) In Sleep Mode, the IC is accessible via the Serial Interface. All circuits, other than those of the CM ...

  • Philips TDA5360 - page 12

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 12 10 BIASING OF THE MR ELEMENT This preamplifier has been designed for SAL and GMR elements. Programming bit GMR in Reg. 01 select either a SAL range (LOW) or a GMR range (HIGH). By programming bi ...

  • Philips TDA5360 - page 13

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 13 10.2 Fault Mode Fault conditions are indicated on the FLT pin (HIGH during write mode and LOW during read mode). The fault condition is coded and stored in Reg. 07 for monitoring purposes. The f ...

  • Philips TDA5360 - page 14

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 14 The following are valid READ fault conditions which set FLT=LOW • Rext pin open or shorted to GND or Vcc • Thermal Asperity detected • Read Head open • Power supplies too low (VCC and/or ...

  • Philips TDA5360 - page 15

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 15 10.3 Serial Interface Address bit Allocation 10.4 Serial Interface Register bit Allocation 9 Register A 7 A 6 A 5 A 4 A 3 A 2 A 1 A 0 0 X 0 0 0 0 CS1 CS0 RWN 1 X 0 0 0 1 CS1 CS0 RWN 2 X 0 0 1 0 ...

  • Philips TDA5360 - page 16

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 16 10.5 Serial Interface Operations The serial interface communication consists of an adress word of 8 bits followed by a data word of 8 bits. See section 11, page 24 and 25 for timing diagrams. 10 ...

  • Philips TDA5360 - page 17

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 17 10.6 Registers description Nb Register Name Contents 0 Head Select Register HS3..HS0 = 0,0,0,0 to 1,0,1,1 = H0 to H11 SELT : if HIGH, the multiple selection detector is enabled. Inactive in STW ...

  • Philips TDA5360 - page 18

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 18 3 Reader Bandwith Register HFZ3, HFZ2, HFZ1, HFZ0 = high frequency gain boost/ differentiator control ( Note 3 ) LFP1, LFP0 = low frequency pole. (0,0) = 1 MHz (0,1) = 2 MHz (1,0) = 3 MHz (1,1) ...

  • Philips TDA5360 - page 19

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 19 8 Measurement Register M4...M0 = 5 bits for Rmr/Temperature digitazation (read back only bits) RANGE1,RANGE0 = 2bits to define which measurement to be done (0,0) RMR measurement for 15 Ω < ...

  • Philips TDA5360 - page 20

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 20 Note 0 : MDS (Multiple Device Selected) detector : When several preamps are connected in parallel, this function allows the user detection of wrong adressing withing the preamps. When SELT is hi ...

  • Philips TDA5360 - page 21

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 21 Formula to link real TAD threshold with LF pole of the reader and programmed input impedance : where : fLFP is the low frequency pole of the read amplifer (1 to 4 MHz, programmable via Reg. 03) ...

  • Philips TDA5360 - page 22

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 22 - Temperature digitizer This measurement can be done either in Active Read mode or in Active Write mode. Note 9a : RSTDMY define DRN pin functionality Note 9b : MODE1,MODE0 power management cont ...

  • Philips TDA5360 - page 23

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 23 The aim of the TAC is to limit the amplitude and the duration of the perturbation seen at the reader output. Because thermal asperity amplitude is not constant, the TAC need some threshold progr ...

  • Philips TDA5360 - page 24

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 24 11 SERIAL INTERFACE TIMING 0...Reg.00 H SEN SCLK SDATA a0=0 a2 a1 a3 a4 a5 a6 a7 Address Data 1 Tclk 0.5 Tclk d0 d1 d2 d3 d4 d5 d5 d7 SEN SCLK SDATA a0=1 a2 a1 a3 a4 a5 a6 a7 Address Data 2 Tclk ...

  • Philips TDA5360 - page 25

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 25 (*) either positive or negative, but ABS (tclklow) > 5ns SEN timing Description Min Nom Max Unit tr_sen_sclk 90% of SEN to 10% of SCLK 5 ns tf_sclk_sen last SCLK to 90% of SEN 5 ns tr,tf rise ...

  • Philips TDA5360 - page 26

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 26 12 ELECTRICAL PARAMETERS 12.1 DC Characteristics Unless otherwise specified, recommended operating conditions apply CS0=CS1=LOW, DRN=HIGH, BFAST=LOW, STWn=HIGH, RIN=18 Ohm, LFP = 1MHz, Imr = 8mA ...

  • Philips TDA5360 - page 27

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 27 12.2 Read Characteristics Unless otherwise specified, recommended operating conditions apply. Voltage compliance for WDP and WDN in current mode CMM of the inputs in current mode 1.5 Vcc -1.7 V ...

  • Philips TDA5360 - page 28

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 28 C IN Differential Input Capacitance 10 pF R IN Differential Input Resistance RIN0=0, RIN1=1 18 Ohm DR Dynamic Range AC input where AVd falls to 90% of its value at@f = 20MHz TBD mV PP CMR Common ...

  • Philips TDA5360 - page 29

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 29 12.3 Write Charateristics Unless otherwise specified, recommended operating conditions apply, I W =50mA, L H =75nH, R H = 10 Ω , f DATA =5MHz, Ambient temperature. SYMBOL PARAMETERS CONDITIONS ...

  • Philips TDA5360 - page 30

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 30 12.4 Switching Characteristics Unless otherwise specified, recommended operating conditions apply Notes: 1. The differential peak to peak voltage swing could be from 0.4V to 1.5V and the common ...

  • Philips TDA5360 - page 31

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 31 5. The noise figure is defined as : NF[dB] = 10xlog[(Vnout/Av) 2 / (4kTxR MR )] where Av is the gain and Vnout is the noise voltage at the output of the amplifier 6. See Section 11 for Serial In ...

  • Philips TDA5360 - page 32

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 32 13 LIMITING VALUES / RECOMMENDED OPERATION CONDITIONS In accordance with the Absolute Maximum System (IEC 134) SYMBOL PARAMETER CONDITIONS MIN. TYP MAX. UNIT V CC Positive Supply voltage range n ...

  • Philips TDA5360 - page 33

    1998 July 30 Philips Semiconductors Objective Specification, Revision 2.2 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads TDA5360 33 Notes 1. A supply by-pass capacitor from V CC to ground or a low pass filter may be used to optimize the PSRR. 2. A supply by-pass capacitor from V EE to ground or a low pass filter may be used ...

  • Philips TDA5360 - page 34

    Philips Semiconductors Objective specification, Revision 2.2 TDA5360 Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or d ...

Produzent Philips Kategorie Stereo Amplifier

Dokumente, die wir vom Produzenten des Geräts Philips TDA5360 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Philips
- Bedienungsanleitungen TDA5360
- Produktkarten Philips
- Informationsbroschüren
- oder Energieetiketten Philips TDA5360
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Philips TDA5360.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Philips TDA5360, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Philips TDA5360. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Philips TDA5360 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Philips TDA5360, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Philips TDA5360 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Philips TDA5360 verständlich ist.

Eine gänzliche Bedienungsanleitung von Philips sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Philips TDA5360 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Philips TDA5360 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Philips TDA5360, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Philips TDA5360 - die uns die ersten Schritte während der Nutzung von Philips TDA5360 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Philips TDA5360 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Philips TDA5360 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Philips TDA5360?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Philips TDA5360 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Philips TDA5360 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)