Deutsch dropdown-ico

Bedienungsanleitung Axis Communications M1145

60 Seiten 1.21 mb
Download

Zur Seite of 60

Summary
  • Axis Communications M1145 - page 1

    AXIS M1 145 Network Camera User Manual ...

  • Axis Communications M1145 - page 2

    About this Document This manual is intended for administrators and users of the AXIS M1 145 Fixed Dome Network Camera, and is applicable to rmware 5.55 and later . It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux- ...

  • Axis Communications M1145 - page 3

    Japan こ の 装 置 は 、 ク ラ ス B 情 報 技 術 装 置 で す 。 こ の 装 置 は 、 家 庭 環 境 で使 用 す る こ と を 目 的 と し て い ま す が 、 この 装 置 が ラ ジ オ やテ レ ビ ジ ョ ン 受 信 機 に 近 接 し て 使用 さ れ る と 、 受 信 障 害 を引 き 起 こ す こ ...

  • Axis Communications M1145 - page 4

    AXIS M1145 Network Camera T able of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Axis Communications M1145 - page 5

    AXIS M1145 Network Camera T able of Contents Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 P erformance Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 5 ...

  • Axis Communications M1145 - page 6

    AXIS M1145 Network Camera Hardware Overview Hardware Overview 1 2 3 4 5 6 7 8 1. Light sensor (only for AXIS M1 145–L) 2. microSD card slot 3. I/O connector 4. Network connector 5. Network LED 6. Status LED 7. P ower LED 8. Control button Dimensions (HXWXD) 44 x 75 x 1 14 mm (1.7 x 3.0 x 4.4 in) Connectors and Buttons For technical specication ...

  • Axis Communications M1145 - page 7

    AXIS M1145 Network Camera Hardware Overview • Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > P orts & Devic ...

  • Axis Communications M1145 - page 8

    AXIS M1145 Network Camera Accessing the Product Accessing the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems. S ...

  • Axis Communications M1145 - page 9

    AXIS M1145 Network Camera Accessing the Product The default administrator user name root is permanent and cannot be deleted. If the password for root is lost, the product must be reset to the factory default settings. See Reset to Factory Default Settings on page 5 1 . To set the password via a standard HTTP connection, enter it directly in the dia ...

  • Axis Communications M1145 - page 10

    AXIS M1145 Network Camera Accessing the Product The Manual T rigger button is used to trigger an action rule from the Live View page. For information about how to congure and enable the button, see Manual Trigger on page 1 0 . Click Snapshot to save a snapshot of the video image. This button is primarily intended for use when the AXIS Media Cont ...

  • Axis Communications M1145 - page 11

    AXIS M1145 Network Camera Accessing the Product Note These controls are available if digital PTZ is enabled in the selected view area, see View Area on page 20 . With the PTZ Control Queue enabled the time each user is in control of the PTZ settings is limited. Click the buttons to request or release control of the PTZ controls. The PTZ Control Que ...

  • Axis Communications M1145 - page 12

    AXIS M1145 Network Camera Media Streams Media Streams The Axis product provides several video stream formats. Y our requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream proles. Other applicatio ...

  • Axis Communications M1145 - page 13

    AXIS M1145 Network Camera Media Streams The AMC Control P anel can be used to congure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on rst use, after which it can be congured. Open the AMC Control P anel from: • Windows Control P anel (from ...

  • Axis Communications M1145 - page 14

    AXIS M1145 Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later . • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this. 14 ...

  • Axis Communications M1145 - page 15

    AXIS M1145 Network Camera Setting Up the Product Setting Up the Product The Axis product can be congured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all ...

  • Axis Communications M1145 - page 16

    AXIS M1145 Network Camera Setting Up the Product 4. Click in the Focus position bar to focus on a desired location. The buttons < and > move the focus position one step in either direction. The buttons << and >> move the focus position in multiple steps in either direction. 5. When satised, click Enable iris to enable the iris. ...

  • Axis Communications M1145 - page 17

    AXIS M1145 Network Camera Setting Up the Product Video It is possible to congure the following video features in your Axis product: • Video stream. See page 17 . • Stream proles. See page 18 . • Camera settings. See page 18 . • View areas. See page 20 . • Overlay image. See page 2 1 . • Privacy mask. See page 22 . • Focus and zo ...

  • Axis Communications M1145 - page 18

    AXIS M1145 Network Camera Setting Up the Product H.264 H.264, also known as MPEG-4 P art 1 0/AVC, is a video compression standard that provides high quality video streams at low bit rates. An H.264 video stream consists of different types of frames such as I-frames and P-frames. An I-frame is a complete image whereas P-frames only contain the diffe ...

  • Axis Communications M1145 - page 19

    AXIS M1145 Network Camera Setting Up the Product Image Appearance Increasing the Color level increases the color saturation. The value 1 00 gives maximum color saturation. The value 0 gives a black and white image. The image Brightness can be adjusted in the range 0–100, where a higher value produces a brighter image. Increasing the Sharpness can ...

  • Axis Communications M1145 - page 20

    AXIS M1145 Network Camera Setting Up the Product Gain , measured in decibel (dB), is the amount of amplication applied to the image. A high gain may provide a better image in low light situations but will increase the amount of image noise. Set Gain to • Auto to set the gain automatically . If required, use Max gain to limit the applied gain. ...

  • Axis Communications M1145 - page 21

    AXIS M1145 Network Camera Setting Up the Product 1. Go to Video > View Area . 2. Click Add . 3. The new view area appears under Selected view area . Enter a descriptive name in the Name eld. 4. Select an Aspect ratio and a Video stream resolution . 5. A new view area covers the whole image. Use the mouse to move and resize the view area. 6. S ...

  • Axis Communications M1145 - page 22

    AXIS M1145 Network Camera Setting Up the Product 2. Click Browse and browse to the le. 3. Click Upload . 4. Select the image to use from the Use overlay image list. 5. Click Save . To display the overlay image: 1. Go to Video > Video Stream and select the Image tab . 2. Under Overlay Settings , select Include overlay image at the coordinates ...

  • Axis Communications M1145 - page 23

    AXIS M1145 Network Camera Setting Up the Product Y ou can add a new mask, re-size the mask with the mouse, choose a color for the mask, and give the mask a name. For more information, see the online help Important Adding many privacy masks may affect the product’s performance. Focus & Zoom For installation instructions, refer to the product? ...

  • Axis Communications M1145 - page 24

    AXIS M1145 Network Camera Live View Config Live View Config Y ou can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 18 . • Default Viewer for Browser . See page 24 . • Viewer Settings. See page 24 . • Action Buttons. T ...

  • Axis Communications M1145 - page 25

    AXIS M1145 Network Camera Live View Config • Select Use PTZ joystick mode as default to enable joystick mode. The mode can be changed temporarily from the PTZ control panel. • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer . The recordings are saved to the location ...

  • Axis Communications M1145 - page 26

    AXIS M1145 Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area. For more information on view areas, see View Area on page 20 . Preset P ositions A preset position is a predened view that can be used to quickly steer the camera to a specic loc ...

  • Axis Communications M1145 - page 27

    AXIS M1145 Network Camera PTZ (Pan Tilt Zoom) Tour Recording The guard tour function in this product includes tour recording, which allows recording of a custom tour using an input device such as a joystick, mouse, keyboard or through the VAPIX® Application Programming Interface (API). A recorded tour displays the video stream of the recorded sequ ...

  • Axis Communications M1145 - page 28

    AXIS M1145 Network Camera Detectors Detectors Camera T ampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. T o send an alarm, for example an email, an action rule must be set up. To congure tampering: 1. Go to Detectors > Camera Tampering . 2. Set the ...

  • Axis Communications M1145 - page 29

    AXIS M1145 Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window . Set Up Motion Detection ...

  • Axis Communications M1145 - page 30

    AXIS M1145 Network Camera Detectors Note • T o trigger on small objects or movements, use several small motion detection windows rather than one large window and select a low object size. • T o avoid triggering on small objects, select a high object size. • While monitoring an area where moving objects are not expected, select a high history ...

  • Axis Communications M1145 - page 31

    AXIS M1145 Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, download ...

  • Axis Communications M1145 - page 32

    AXIS M1145 Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings . 32 ...

  • Axis Communications M1145 - page 33

    AXIS M1145 Network Camera Events Events The Axis product can be congured to perform actions when different events occur , for example, start a recording when motion is detected. The set of conditions that denes how and when the action is triggered is called an Action Rule . Available action rule triggers and conditions include: • Applicatio ...

  • Axis Communications M1145 - page 34

    AXIS M1145 Network Camera Events - Recurrence – T rigger the rule periodically . See Recurrences on page 36 . This can for example be used to upload an image every 5 minutes. - Use Schedule – T rigger the rule according to the selected schedule. See Schedules on page 36 . Available actions include: • Day/Night Vision Mode – Set day mode (IR ...

  • Axis Communications M1145 - page 35

    AXIS M1145 Network Camera Events To add additional criteria, select the Additional conditions option and add additional triggers. T o prevent an action from being triggered repeatedly , a Wait at least time can be set. Enter the time in hours, minutes and seconds, during which the trigger should be ignored before the action rule can be activated ag ...

  • Axis Communications M1145 - page 36

    AXIS M1145 Network Camera Events 5. Click Test to test the connection to the recipient. 6. Click OK . Setting Up an Email Recipient Email recipients can be congured by selecting one of the listed email providers, or by specifying the SMTP server , port and authentication used by , for example, a corporate email server . Note Some email providers ...

  • Axis Communications M1145 - page 37

    AXIS M1145 Network Camera Events To use the recurrence in an action rule, rst select Time from the T rigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list. To modify or remove recurrences, select the recurrence in the Recurrences List and click Modify or Remove . 37 ...

  • Axis Communications M1145 - page 38

    AXIS M1145 Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 38 . • To set up action rules, see page 34 . • To access recordings, see Recording List on page 38 . • To congure camera controlled storage, see Stora ...

  • Axis Communications M1145 - page 39

    AXIS M1145 Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. T o switch languages, go to Setup > Languages and rst upload the new language le. Browse and locate the le and click the Upload Language button. Select ...

  • Axis Communications M1145 - page 40

    AXIS M1145 Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may acc ...

  • Axis Communications M1145 - page 41

    AXIS M1145 Network Camera System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally , click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection P olicy for the different user groups. 5. Click Save to enable the settings. To access the Axis product via the desired prot ...

  • Axis Communications M1145 - page 42

    AXIS M1145 Network Camera System Options To install a self-signed certicate: 1. Go to Setup > System Options > Security > Certicates . 2. Click Create self-signed certicate and provide the requested information. To create and install a CA-signed certicate: 1. Create a self-signed certicate as described above. 2. Go to Setup ...

  • Axis Communications M1145 - page 43

    AXIS M1145 Network Camera System Options IPv4 Address Conguration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP . The IPv4 settings are congured under System Options > Network > T CP/IP > Basic . DHCP (Dynamic Host Conguration Protocol) allows network administrat ...

  • Axis Communications M1145 - page 44

    AXIS M1145 Network Camera System Options 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar . 6. Open a browser and type http://<IP address> in the Location/Address eld. For other methods of assigning the IP address, see the Installation and Management Software CD or the document Assign an IP ...

  • Axis Communications M1145 - page 45

    AXIS M1145 Network Camera System Options NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are congured under System Options > Network > T CP/IP > Advanced . Select Obtain NTP server address via DHCP to use the NTP settings provided by the DHCP server . To mak ...

  • Axis Communications M1145 - page 46

    AXIS M1145 Network Camera System Options Use manually selected NA T router - Select this option to manually select a NA T router and enter the IP address for the router in the eld. If no router is specied, the product automatically searches for NA T routers on your network. If more than one router is found, the default router is selected. Alt ...

  • Axis Communications M1145 - page 47

    AXIS M1145 Network Camera System Options Note If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled. Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that sh ...

  • Axis Communications M1145 - page 48

    AXIS M1145 Network Camera System Options • ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required. • vFAT — supported by most operating systems for personal co ...

  • Axis Communications M1145 - page 49

    AXIS M1145 Network Camera System Options P orts & Devices I/O P orts The Axis product provides one input port and one output port for connection of external devices. For information about how to connect external devices, see Connectors on page 58 . The I/O ports are congured under System Options > P orts & Devices > I/O P orts . Th ...

  • Axis Communications M1145 - page 50

    AXIS M1145 Network Camera System Options See also T roubleshooting on page 52 . System Overview To get an overview of the Axis product’s status and settings, go to System Options > Support > System Overview . Information that can be found here includes rmware version, IP address, network and security settings, event settings, image setti ...

  • Axis Communications M1145 - page 51

    AXIS M1145 Network Camera System Options Plain Cong Plain Cong is for advanced users with experience of Axis product conguration. Most parameters can be set and modied from this page. To open Plain Cong, go to System Options > Advanced > Plain Cong . Axis Support does not provide assistance. Reset to Factory Default Settings ...

  • Axis Communications M1145 - page 52

    AXIS M1145 Network Camera Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version. The latest version may contain a correction that xes your particular problem. The cu ...

  • Axis Communications M1145 - page 53

    AXIS M1145 Network Camera Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www .axis.com/techsup/ Symptoms, Possible Causes and Remedial Actions Problems setting the IP address When using ARP/Ping Try the installa ...

  • Axis Communications M1145 - page 54

    AXIS M1145 Network Camera Troubleshooting Problems with streaming H.264 Problems with AXIS Media Control ( Internet Explorer only ) To enable the updating of video images in Internet Explorer , set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer . No H.264 displayed in the client Check th ...

  • Axis Communications M1145 - page 55

    AXIS M1145 Network Camera Troubleshooting Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur . T o identify the source of the problem, check the System Log under System Options > Support > Logs & Repor ...

  • Axis Communications M1145 - page 56

    AXIS M1145 Network Camera T echnical Specifications T echnical Specifications Function/group Item Specications Models AXIS M1 145: 2 MP/ HDTV 1 080p Image sensor 1/2.9 progressive scan RGB CMOS Lens Varifocal, P-iris, with built in IR-cut lter and motorized focus/zoom, 3-1 0.5 mm, F1.4 Horizontal angle of view: 95°- 34° V ertical angle of ...

  • Axis Communications M1145 - page 57

    AXIS M1145 Network Camera T echnical Specifications Function/group Item Specications Application Programming Interface Open API for software integration, including VAPIX® and AXIS Camera Application Platform; specications at www .axis.com AXIS Video Hosting System (A VHS) with One-Click Camera Connection. ONVIF Prole S; specication at ...

  • Axis Communications M1145 - page 58

    AXIS M1145 Network Camera T echnical Specifications Function/group Item Specications Optional accessories AXIS T9 1A04 Camera Holder AXIS T9 1A05 Camera Holder AXIS P822 1 Audio Module AXIS T90A White LED Illuminators AXIS P oE products Languages German, French, Spanish, Italian, Russian, Simplied Chinese, Japanese, K orean, P ortuguese Warr ...

  • Axis Communications M1145 - page 59

    AXIS M1145 Network Camera T echnical Specifications 3. 3 V max 50 m A 1 2 3 4 SD Card Slot Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 1 0. P erformance Considerations When settings up your system, it is important to consider how various settings and situati ...

  • Axis Communications M1145 - page 60

    User Manual V er . M2.2 AXIS M1 145 Network Camera Date: April 20 14 © Axis Communications AB, 20 14 P art No. 57266 ...

Produzent Axis Communications Kategorie Security Camera

Dokumente, die wir vom Produzenten des Geräts Axis Communications M1145 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Axis Communications
- Bedienungsanleitungen M1145
- Produktkarten Axis Communications
- Informationsbroschüren
- oder Energieetiketten Axis Communications M1145
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Axis Communications M1145.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Axis Communications M1145, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Axis Communications M1145. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Axis Communications M1145 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Axis Communications M1145, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Axis Communications M1145 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Axis Communications M1145 verständlich ist.

Eine gänzliche Bedienungsanleitung von Axis Communications sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Axis Communications M1145 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Axis Communications M1145 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Axis Communications M1145, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Axis Communications M1145 - die uns die ersten Schritte während der Nutzung von Axis Communications M1145 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Axis Communications M1145 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Axis Communications M1145 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Axis Communications M1145?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Axis Communications M1145 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Axis Communications M1145 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)