Bedienungsanleitung Audiovox APS-700

24 Seiten 0.46 mb
Download

Zur Seite of 24

Summary
  • Audiovox APS-700 - page 1

    APS-700 Installation Guide Remote Control Security System With Pager/Satellite Control Interface Installation Instructions Kit Contents APS-700 Control Module 4 Channel Code Learning Receiver 2 Three Button Anti-Code Grabbing T ransmitters Six T one Multi-T one Siren Starter Inhibit Relay w/Socket Main Wiring Harness Auxiliary Wiring Harness Plug I ...

  • Audiovox APS-700 - page 2

    The APS-700 is a full featured security system with on board paging technology that provides the consumer a direct link to their vehicle from anywhere in the world. This patent pending technology allows the user to operate the vehicle from any land or mobile telephone. The vehicle's owner can command the security system to arm or disarm, relea ...

  • Audiovox APS-700 - page 3

    VALET/PROGRAM SWITCH: Select a mounting location that is easily accessible to the operator of the vehicle. The switch can be mounted to the lower dash panel in the driver's area. Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch, as well that the drill will not penetrate any existing fac ...

  • Audiovox APS-700 - page 4

    White w/ Black T race W ire: Positive (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren location. Connect the White w/ Black T race wire to the Red wire of the Siren. Secure the Black wire of the Siren to a known chassis ground or solid clean metal surface. Black Wire: Chassis Grou ...

  • Audiovox APS-700 - page 5

    Dark Green Wire: (-) Instant T rigger Zone 2 The Dark Green wire is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin switches previously installed. Note: This wire will be shunted when remote control channel 2 is accessed, (trunk release). This wire will remain shunted all the while there is ground pre ...

  • Audiovox APS-700 - page 6

    2 Pin Auxiliary Harness: (Red Connector) The two pin auxiliary connector is used to control vehicle shut down from a paging theft command. See supplement for wiring information. Connecting The Dash Mounted LED: Plug the two pin white connector from the previously installed LED into the mating two pin white female connector shell of the control modu ...

  • Audiovox APS-700 - page 7

    LED Flash Pattern 1 Flash Pause etc. 2 Falsh Pause etc. 3 Flash Pause etc. 4 Flash Pause etc. 5 Flash Pause etc. 6 Flash Pause ect. ALARM SELECT ABLE FEA TURES RF Programmable Features: Feature Selection 1 Chirp 2 Chirp Default First 1 Second Door Locks 3.5 Second Door Lock 1 Second Second Auto Lock On Auto Lock Off Auto Lock Off Third Auto Unlock ...

  • Audiovox APS-700 - page 8

    8 LEFT FRONT & REAR COMMON RIGHT FRONT & REAR COMMON RIGHT SIDE ...

  • Audiovox APS-700 - page 9

    VEHICLE YEAR VEHICLE MFG. VEHICLE MOD. VEHICLE COLOR LICENSE PLA TE# VIN# CHANNEL 2 AUXILIARY OUTPUT 1 IS CONNECTED TO CHANNEL 3 AUXILIARY OUTPUT 2 IS CONNECTED TO CHANNEL 4 AUXILIARY OUTPUT 3 IS CONNECTED TO VEHICLE INFORMA TION PRODUCT INFORMA TION SERIAL # COUNTRY CODE DLR/DIST ID# INST ALLA TION DA TE ALARM P AGER THE FOLLOWING OPTIONS HA VE BE ...

  • Audiovox APS-700 - page 10

    10 DARK BLUE CHANNEL 2 / AUXILIARY 1 OUTPUT SHOCK SENSOR RED, BLACK, BLUE AND GREEN WIRES TO PLUG IN SHOCK SENSOR +12 VOL T BA TTER Y CONNECT TO A +12 VOL TS FULL TIME BA TTER Y SOURCE RED w/WHITE WHTIE w/BLACK Clean Non-Painted Metal Surface BLACK CHASSIS GROUND WHITE LOW CURRENT OUTPUT RIGHT SIDE LIGHT FLASHER SEE SPECIAL NOTES REGARDING APPLICA ...

  • Audiovox APS-700 - page 11

    11 APS - 700 FROM DOME LIGHT FUSE BROWN (DOOR -) PURPLE (DOOR +) YELLOW IGNITION SOURCE Connect to a Source that has +12 with the Key in the ON and Start Modes WHITE w/BLUE HEADLIGHT OUTPUT 30 Second Output During Arm and Disarm. Relay Required LIGHT GREEN ZONE 1 Connect to Optional Negative Triggering Devices RED GREEN RED DOOR LOCK OUTPUTS (+) LO ...

  • Audiovox APS-700 - page 12

    VSS WIRING SUPPLEMENT The two pin auxiliary harness with the red connector shell provides a input signal to the control module from the vehicle's S peed Sensor ( VSS), and provides a low current ground switched output to control a shut down relay . The relay can be used to interrupt any circuit in the vehicle which will cause the vehicle' ...

  • Audiovox APS-700 - page 13

    Modelo APS-700 Guía de instalación Sistema de seguridad a control remoto con sistema de aviso/interfaz de control de satélite Instrucciones de instalación Contenido del kit: Módulo de control APS-700 Receptor con captación de código de 4 canales 2 transmisores de 3 botones con escalonamiento de frecuencias de código Sirena de seis tonos Rel ...

  • Audiovox APS-700 - page 14

    14 El sistema APS 700 es un sistema de seguridad de múltiples funciones con la tecnología de aviso incorporada que proporciona al consumidor en enlace directo con su vehículo desde cualquier lugar del mundo. Esta nueva tecnología, cuya patente se encuentra pendiente, permite al usuario operar el vehículo desde cualquier teléfono común o móv ...

  • Audiovox APS-700 - page 15

    15 INTERRUPTOR V ALET / PROGRAMACIÓN : Elija un lugar de montaje al que el operador del vehículo tenga fácil acceso. Se puede montar el interruptor en el panel inferior del tablero en el área del conductor . Asegúrese de fijarse detrás del tablero para comprobar si hay el suficiente espacio para la caja del interruptor y para confirmar que el ...

  • Audiovox APS-700 - page 16

    16 Cable testigo blanco y negro: Salida positiva de la sirena (+) Es una cable de alimentación positiva de la sirena. Pase este cable por un ojal del muro contrafuego hacia el lugar de la sirena. Conecte el cable testigo blanco y negro de la sirena. Fije el cable negro de la sirena a una conexión a tierra del chasis o a una superficie metálica l ...

  • Audiovox APS-700 - page 17

    17 Cable verde oscuro: Entrada (-) de activación instantánea Zona 2 Es el cable de entrada de activación instantánea o conexión a tierra. Este cable tiene que estar conectado a los interruptores de clavija del capó o baúl que se instalaron antes. Nota: Este cable se derivará cuando se acceda al canal 2 del control remoto (desenganche del ba ...

  • Audiovox APS-700 - page 18

    18 Arnés auxiliar de 2 clavijas (conector rojo): Se usa el conector auxiliar de 2 clavijas para controlar el apagado del vehículo con un comando de robo enviado por el sistema de aviso. V er suplemento para obtener información de cableado. Conexión del indicador LED que va montado en el tablero: Enchufe el conector blanco de dos clavijas del in ...

  • Audiovox APS-700 - page 19

    Conexión y ajuste del detector de choque: Pase el cable de 4 clavijas del detector de choque ya instalado hacia el módulo de control. Enchúfelo en el conector blanco de 4 clavijas ubicado al lado del conector de 8 clavijas del conector del arnés de la unidad de control. Ajuste el detector de choque ya instalado accediendo primero al tornillo de ...

  • Audiovox APS-700 - page 20

    20 DELANTERA Y TRASERA IZQUIERDAS EN COMÚN DELANTERA Y TRASERA DERECHAS EN COMÚN A LA FUENTE DE +12 VOL TIOS CON FUSIBLES AL PRIMER CABLE BLANCO DEL MÓDULO DE CONTROL AL SEGUNDO CABLE BLANCO DEL MÓDULO DE CONTROL DEL INTERRUPTOR DIRECCIONAL DEL VEHÍCULO LADO DERECHO LADO DERECHO LADO IZQUIERDO Corte A LA FUENTE DE +12 VOL TIOS CON FUSIBLES TRA ...

  • Audiovox APS-700 - page 21

    INFORMACIÓN SOBRE EL VEHÍCULO AÑO DEL VEHÍCULO F ABRICANTE DEL VEHÍCULO MODELO DEL VEHÍCULO COLOR DEL VEHÍCULO CHAP A P A TENTE VIN# 21 ALARMA SISTEMA DE A VISO CANAL 2 SALIDA AUXILIAR 1 ESTÁ CONECT ADA A __________ CANAL 3 SALIDA AUXILIAR 2 ESTÁ CONECT ADA A __________ CANAL 4 SALIDA AUXILIAR 3 ESTÁ CONECT ADA A __________ INFORMACIÓN S ...

  • Audiovox APS-700 - page 22

    22 AZUL OSCURO SALIDA CANAL 2 / AUXILIAR 1 DETECTOR DE CHOQUE CABLES ROJO, NEGRO, AZUL Y VERDE P A R A ENCHUF AR EL DETECTOR DE CHOQUE BA TERÍA DE +12 VOL TIOS CONECT AR A UNA BA TERÍA D E +12 VOL TIOS CONST ANTES ROJO Y BLANCO BLANCO Y NEGRO Superficie metálica limpia y sin pintura NEGRO CONEXIÓN A TIERRA DEL CHASIS BLANCO SALIDA DE BAJA CORRI ...

  • Audiovox APS-700 - page 23

    23 APS - 700 Del fusible de luces MARRÓN (puerta -) VIOLET A (puerta +) AMARILLO FUENTE DE ENCENDIDO Conectar a una fuente que tenga +12 voltios cuando la llave esté en los modos “on” y “start”. BLANCO Y AZUL SALIDA DE FAROS Saluda a tierra de 30 segundos durante la activación y desactivación Se requiere un relé VERDE CLARO ZONA 1 Cone ...

  • Audiovox APS-700 - page 24

    24 SUPLEMENTO DE CABLEADO DEL VSS El arnés de cableado auxiliar de dos clavijas que tiene el conector rojo proporciona una señal de entrada al módulo de control del Detector de velocidad del vehículo (VSS por las siglas en inglés) y proporciona una salida conmutada de conexión a tierra de baja corriente para controlar un relé de apagado. Se ...

Produzent Audiovox Kategorie Remote Starter

Dokumente, die wir vom Produzenten des Geräts Audiovox APS-700 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Audiovox
- Bedienungsanleitungen APS-700
- Produktkarten Audiovox
- Informationsbroschüren
- oder Energieetiketten Audiovox APS-700
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Audiovox APS-700.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Audiovox APS-700, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Audiovox APS-700. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Audiovox APS-700 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Audiovox APS-700, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Audiovox APS-700 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Audiovox APS-700 verständlich ist.

Eine gänzliche Bedienungsanleitung von Audiovox sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Audiovox APS-700 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Audiovox APS-700 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Audiovox APS-700, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Audiovox APS-700 - die uns die ersten Schritte während der Nutzung von Audiovox APS-700 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Audiovox APS-700 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Audiovox APS-700 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Audiovox APS-700?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Audiovox APS-700 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Audiovox APS-700 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)