Bedienungsanleitung Bunn G1

21 Seiten 2.16 mb
Download

Zur Seite of 21

Summary
  • Bunn G1 - page 1

    C L E A N I N G L E V E R G R O UN D C O FF EE 1 . S e l e c t t h e de s i r e d g r in d . 2 . L i f t t h e l i d a n d p o u r c o f f e e b e a n s in t o t h e h op p e r . 3 . S l i p b a g u n d e r t h e c h u t e . R e s t t he b a g o n t h e t r a y . 4 . P r e s s t h e s ta r t s w i t c h . 5 . F l i p t h e c l e a n in g le v e r a ...

  • Bunn G1 - page 2

    2 10191 070306 BUNN-O-MA TIC COMMERCIAL PRODUCT W ARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years par ...

  • Bunn G1 - page 3

    3 SPECIAL R E G U L A R E L E C P E R C A U T O M A T I C D R I P ...

  • Bunn G1 - page 4

    4 ELECTRICAL REQUIREMENTS The 120 volt and 240 volt grinders have an attached cordset and requires 2-wire, grounded service rated 120 volts ac and 240 volts ac, 15 amp, single phase, 60 Hz. The 230 volt grinders have a power connector and requires 2-wire, grounded service rated 230 volts ac, 15 amp, single phase, 50 Hz. INITIAL SET -UP CAUTION - Un ...

  • Bunn G1 - page 5

    5 COFFEE GRINDING 1. T urn the selector knob to align the red arrow with the desired grind. 2. Raise the top lid and add the whole bean coffee. Close the top lid. 3. Locate the back of a bag behind the dispense chute. (The grinder will not operate unless the bag is behind the chute.) 4. Allow the bag to rest on the screen beneath the chute. 5. Pres ...

  • Bunn G1 - page 6

    6 A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department. • Inspection, testing, and repair of electrical equipment should be performed only by qualified service ...

  • Bunn G1 - page 7

    7 PROBABLE CAUSE 3. Bag Sensor . (cont.) 4. Motor overload protector . 1. Off/On/Start Switch 2. Bag Sensor 3. Relay TROUBLESHOOTING (cont.) PROBLEM Grinder will not start. (cont.) Grinder will not shut off. REMEDY (B) Refer to Ser vice - Bag Sensor Switch for testing and adjustment procedures. See page 9. Remove the plug located on the right side ...

  • Bunn G1 - page 8

    8 TROUBLESHOOTING (cont.) PROBABLE CAUSE 1. Hopper 2. Entrance to grind chamber 3.Shear Plate PROBLEM Grinder starts, but will not dis- pense. REMEDY Coffee must be poured into hopper before grinding. Foreign materials must not block the opening at the bottom of the hopper . Remove both black fillister head screws holding the grinder selector dial ...

  • Bunn G1 - page 9

    9 CONTENTS Bag Sensor Switch ..............................................9 Motor and Grind Chamber (AC) ........................10 Motor and Grind Chamber (DC) ........................13 Off/On/Start Switch ...........................................16 Rectifier ............................................................17 Relay ............... ...

  • Bunn G1 - page 10

    10 4. Disconnect the grinder from the power source. If voltage is present as described, proceed to #5. If voltage is not present as described, refer to the Wiring Diagrams and check the grinder wiring harness. 5. Check for continuity across the terminals on the bag sensor switch. If continuity is present as described, reconnect the wires, the switc ...

  • Bunn G1 - page 11

    11 SERVICE (cont,) AC MOTOR AND GRIND CHAMBER (cont.) WHI/BLU to Relay N.O.(K4) WHI to Cordset (120V) RED/BLK to Cordset (230V) GRN to Ground (120V) GRN/YEL to Ground (230V) P1310 Removal and Replacement - Grind Chamber - Refer to Fig. 6: 1. Lo osen the tw o set scre ws (1 6) sec uri ng the gri nd selector knob to the grind selector dial plate (18) ...

  • Bunn G1 - page 12

    12 SERVICE (cont.) ...

  • Bunn G1 - page 13

    13 17. Ins tal l grind selec tor dial plat e (18) with adju sting scr ew w/be aring (19) onto the gr ind cham ber and secure with two .250”-20 screws (1). 18. Install grind selector knob (17) onto the grind selector dial plate (18). NOTE: Refer to ADJUSTMENTS and reset the burrs. SERVICE (cont.) DC MOTOR AND GRIND CHAMBER - G1MD ONL Y ...

  • Bunn G1 - page 14

    14 SERVICE (cont,) DC MOTOR AND GRIND CHAMBER - G1MD ONL Y (cont.) ...

  • Bunn G1 - page 15

    15 SERVICE (cont,) DC MOTOR AND GRIND CHAMBER - G1MD ONL Y (cont.) ...

  • Bunn G1 - page 16

    16 Location: The Off/On/Start switch is located in the up- per front wrapper above and to the right of the grind selector knob (left side when viewed from rear). T est Procedure: 1. Disconnect the grinder from the power source. 2. Check the voltage across the black wire on the Off/On/Star t switch and the white wire or the red/ black on the relay c ...

  • Bunn G1 - page 17

    17 + A C A C SERVICE (cont.) Removal and Replacement: 1. Disconnect the wires from the rectifier . 2. Remove the #10-32 screw securing the rectifier to the motor mounting bracket. 3. Remove the rectifier and discard. 4. Install new rectifier on the rear of the motor mounting bracket and secure with a #10-32 screw . 5. Refer to Fig. 13 and recon ...

  • Bunn G1 - page 18

    18 Location: The relay is located on the grinder base inside the lower housing. T est Procedure: 1. Disconnect the grinder from the power sour ce and place a coffee bag behind the dispense chute. 2. Check the voltage across the white/orange and white or red/black wires on terminals A & B of the relay with a voltmeter . Hold the Off/On/Start swi ...

  • Bunn G1 - page 19

    19 ...

  • Bunn G1 - page 20

    20 WHI/VIO WHI/VIO WHI/BLU WHI/ORA 1 or A GRN L1 N SW1 BLK WHI/RED SW2 K 0 or B M L1 L2 120 VOL T AC 2 WIRE SINGLE PHASE 60 HZ WHI WHI K-2 or K-7 K-8 or K-9 K-6 K-4 SCHEMA TIC WIRING DIAGRAM G1, G2 & G3 10190.0000G 07/05 © 1985 BUNN-O-MA TIC CORPORA TION 10191 070306 ...

  • Bunn G1 - page 21

    21 WHI/VIO WHI/VIO WHI/BLU WHI/ORA SCHEMA TIC WIRING DIAGRAM G1A, G2A & G3A GRN/YEL L1 L2 SW1 BLK WHI/RED WHI/RED SW2 N.O. N.O. M L1 L2 RED (230V) RED/BLK (240V) RED (230V) RED/BLK (240V) 10754.0000E 07/05 © 1993 BUNN-O-MA TIC CORPORA TION K-4 K-6 230 VOL TS AC 240 VOL TS AC 2 WIRE SINGLE PHASE K 1 or A 0 or B K-2 or K-7 K-8 or K-9 10191 07030 ...

Produzent Bunn Kategorie Coffee Grinder

Dokumente, die wir vom Produzenten des Geräts Bunn G1 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Bunn
- Bedienungsanleitungen G1
- Produktkarten Bunn
- Informationsbroschüren
- oder Energieetiketten Bunn G1
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Bunn G1.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Bunn G1, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Bunn G1. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Bunn G1 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Bunn G1, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Bunn G1 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Bunn G1 verständlich ist.

Eine gänzliche Bedienungsanleitung von Bunn sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Bunn G1 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Bunn G1 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Bunn G1, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Bunn G1 - die uns die ersten Schritte während der Nutzung von Bunn G1 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Bunn G1 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Bunn G1 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Bunn G1?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bunn G1 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bunn G1 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)