Bedienungsanleitung Telex XO-AP XO-1

19 Seiten 1.13 mb
Download

Zur Seite of 19

Summary
  • Telex XO-AP XO-1 - page 1

    XO-AP XO-1 Wireless Intercom System Telex ® Operating Manual Wireless Intercom System Telex Communicat ions, Inc. ...

  • Telex XO-AP XO-1 - page 2

    Table of Contents Section 1 Introduction 1-1 General Description .............................................................................................................1-1 System Features ...................................................................................................................1-1 Section 2 XO-AP Base S tation 2-1 Con ...

  • Telex XO-AP XO-1 - page 3

    General Descript ion The Telex Legacy ä Series is a full duple x (simultaneou s talk and listen), m ulti-channel, wirele ss intercom system. Legacy of fers a complete solution for 2 to 7 coaches per sideline, fast and easy set-up, durable beltpacks, 64 bit audio encrypt ion, and professional grade headsets. The main components of the Legacy ä ser ...

  • Telex XO-AP XO-1 - page 4

    1. On/Off Switch – Turns the powe r on/off to the ba se station. 2. Power / Low Batt ery Light – Indicates the ba se station has power , either fr om the int ernal battery or external power c onnected to the unit. Battery Indicat ion: • GREEN - Battery OK • RED - Battery Low (n eeds charged) 3. Transmit Antenna Jack – This reverse TNC jac ...

  • Telex XO-AP XO-1 - page 5

    1. On/Off & Volume Control – Turns the beltpac k power on/off and control s headset volume. 2. Battery Light – • GREEN - Battery OK • RED - Battery Low (n eeds charged) 3. "O" Channel Button and Light – Selects the “Offense” i ntercom channel. The light next to the button will light when s electe d. Also control s headse ...

  • Telex XO-AP XO-1 - page 6

    Section 4 - Specifications RF Technology ............................................................................................................IEEE 802.11 ( Wi Fi) Frequency Band of Operation ......................................................................................2.412 to 2.462 GHz FCC License ................................... ...

  • Telex XO-AP XO-1 - page 7

    Set-up Prior to use, the XO-1 beltpacks and the XO-AP base station need to have their batter y packs fully charged. Refer to the charging instructions of this sect ion for instructions on charging. 1. Place the XO-AP base station in the area of use. 2. Attached the two antenna cables from the antenna to the XO-AP . The cable marked, “Receive” c ...

  • Telex XO-AP XO-1 - page 8

    2. You can now scan for another channel, manually select a channel or lock the current channel by using one of the following procedures: • Clear Scan – Hold the <SELECT> button until the decimal point sta rts to blink (about 3 seconds) then release. The XO-AP will scan all available channels and then set itself to the clearest channel ava ...

  • Telex XO-AP XO-1 - page 9

    ° Release the “O” or “X” button, and the <TALK> button when at the desired level. • The higher the microphone gain the louder that beltpack user’s voice will sound to ot her users and themselves. Halftime 1. During halftim e leave the XO-AP base station “On”. 2. The XO-1 beltpacks may be turned off for halftime to conserve ba ...

  • Telex XO-AP XO-1 - page 10

    Li-Ion Batteries The Li-Ion batteries used in the XO-1 and XO-AP are excellent batteries for portab le, outdoor app lications. They have a high energy density (energy per weight ) compare to other rechargeable battery tec hnologies ( NiCd , NiMH, Alkaline, G el Cells), are low maintenance, and offer superior perfo rmance at low temperatures. For be ...

  • Telex XO-AP XO-1 - page 11

    Encryption Code The Legacy system uses a 64 bit DES (Digital Encryption Standard) encryption algori thm to encrypt all audio in the system. The beltpacks in the system have a “key” in the software that the algorithm uses as the basis for the encryption. The same “key” m ust be used in all beltpacks on the system for communication to occur. ...

  • Telex XO-AP XO-1 - page 12

    9. Press and hold down the “X” button on the beltpack. Keep holding the “X” button and turn-on the beltpack. Hold the beltpack button down until the green LED next to the “X” button lights up (about 20 seconds), then release button ( Places the beltpack in programming mode). 10. Plug the other end of the Ethernet cable into t he beltpac ...

  • Telex XO-AP XO-1 - page 13

    Please rerea d the operat ion and encry ption secti on of this m anual to make s ure you have c omplet ed syste m set -up properly. The following contai ns troubl eshooting tips t hat m ay be helpf ul in solving the problem . Section 7 - Troubleshooting If you are unabl e to solve t he problem , contact the manufac turer or dealer from whom you pur ...

  • Telex XO-AP XO-1 - page 14

    Section 7 - Trouble shooting continued Problem Possible Cause Solution When the XO-1 beltpack powe r was turned on, the unit 's power l ight cam e up, but the "O" butt on light neve r cam e up and comm unicati on never star ted. • Internal battery is nearly exhaused. • On boot, an error was enc ountered and the unit coul d not fi ...

  • Telex XO-AP XO-1 - page 15

    802.11 RF Channels The Legacy system has the ability to operate on any one of eleven RF channels. Although there are several different frequency channel settings, there is overlap between the channels. There are three non-overlapping channels available in t he FCC regulatory domain. When choosing frequency channels for systems in the vicinity of ea ...

  • Telex XO-AP XO-1 - page 16

    Regulatory Infor mation The XO-1 and XO-AP comply with Part 15 of FCC rules and Canada RSS-210 . Operation is subject to the following conditions: 1. This device may not cause harm ful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3. Use only the manufacturer or dealer ...

  • Telex XO-AP XO-1 - page 17

    Section 10 - Accessories and Replacement Items Model Number Part Number Description LP-XO1 301950002 XO-1 Beltpack and Batter y Charger. NOTE: User must provide XO-AP serial num ber and IP address of all XO-1/XO-APs in system with order. PH-1 64438100LG Single si ded w/flexibl e dynam ic boom m ic, 150 ohm earphone, 6" (1.8m) cord and A4F conn ...

  • Telex XO-AP XO-1 - page 18

    Model Number Part Number Description ANT-FP 302054001 Dual Diversity, Flat Patch Antenna with Dua l Coax, 11dB i ANT-FPM 302054000 Metal Tilt and Sw ivel Antenna Mounting bracket for ANT-FP Antenna. Use for perm anent mount of ANT -FP Flat Panel Antenna. XOB 302054002 Nylon Belt, Ad justable 10-2 Section 10 - Acce ssories and Repl acement Ite ms Co ...

  • Telex XO-AP XO-1 - page 19

    8601 East Cornhusker Highway, Lincoln, NE 68507 Made in U.S.A. PN 804233-TX ...

Produzent Telex Kategorie Intercom System

Dokumente, die wir vom Produzenten des Geräts Telex XO-AP XO-1 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Telex
- Bedienungsanleitungen XO-AP XO-1
- Produktkarten Telex
- Informationsbroschüren
- oder Energieetiketten Telex XO-AP XO-1
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Telex XO-AP XO-1.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Telex XO-AP XO-1, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Telex XO-AP XO-1. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Telex XO-AP XO-1 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Telex XO-AP XO-1, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Telex XO-AP XO-1 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Telex XO-AP XO-1 verständlich ist.

Eine gänzliche Bedienungsanleitung von Telex sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Telex XO-AP XO-1 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Telex XO-AP XO-1 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Telex XO-AP XO-1, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Telex XO-AP XO-1 - die uns die ersten Schritte während der Nutzung von Telex XO-AP XO-1 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Telex XO-AP XO-1 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Telex XO-AP XO-1 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Telex XO-AP XO-1?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Telex XO-AP XO-1 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Telex XO-AP XO-1 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)