-
Shure SCM410 - page 1
SCM410/SCM410E FOUR CHANNEL AUT OMA TIC MICROPHONE MIXER Shure Brothers Incorporated 222 Hartrey Avenue Evanston IL 60202-3696 U.S.A. Model SCM410/SCM410E User Guide 27A8690 (SG) 1999, Shure Brothers Incorporated Printed in U.S.A. U.S. Patents 4,658,425; 5,297,210 ...
-
Shure SCM410 - page 2
2 T ABLE OF CONTENTS DESCRIPTION 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FEA TURES 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Shure SCM410 - page 3
3 DESCRIPTION The Shure Model SCM410/E is a four-channel automatic mi- crophone mixer designed for use in sound reinforcement, au- dio recording, and broadcast applications. The SCM410 dra- matically improves audio quality in any application where mul- tiple microphones are required. Any low-impedance dynamic or condenser microphone (including wire ...
-
Shure SCM410 - page 4
4 REAR P ANEL MODEL SCM410 REAR P ANEL FIGURE 2 1. Power Connector: Unit is energized when the power cord is plugged into a 100–120 V ac (SCM410) or 220–240 V ac (SCM410E) power source. Can be internally modified.Refer to the “Internal Modification” section. NOTE: There is no power On/Off switch on this mixer . 2. DIP Switch: The 4-position ...
-
Shure SCM410 - page 5
5 INST ALLA TION SUPPLIED HARDW ARE 4 rubber feet 1 rackmount bracket, long 1 rackmount bracket, short 2 straddle brackets 10 bracket screws, 6 mm (1/4 in.) 4 rackmount screws, 2.54 cm (1 in.) 4 plastic washers 4 wood screws, 1.25 cm (1/2 in.) RACK MOUNTING The SCM410 is supplied with hardware for mounting one or two ...
-
Shure SCM410 - page 6
6 T ABLE-TOP MOUNTING Adhere the four (4) supplied rubber feet to the bottom of the mixer at each corner , as shown in Figure 9. This will keep it from sliding and protect the table surface. A TT ACHING RUBBER FEET FOR T ABLE–TOP MOUNTING FIGURE 9 FIXED MOUNTING T op Mount 1. Fasten the straddle brackets to the recessed edges of the chassis, u si ...
-
Shure SCM410 - page 7
7 SCM410 CONNECTIONS 1. Connect microphone signal sources to the Channel Input connectors, as shown in Figure 14. Use conventional 2-con- ductor shielded audio cables. 2. I f any condenser microphones are connected, set the +12V phantom power DIP switch to ON. 3. Connect the SCM410 Mic/Line Level Output to the input of mixers, EQs, amplifiers or re ...
-
Shure SCM410 - page 8
8 BASIC MIXER OPERA TION 1. Adjust each channel level so that its Overload LED flickers only during very loud speech or noise. 2. Adjust the Low-Cut and High-Frequency controls adjacent to each Input Gain control so that the microphones sound similar . 3. Adjust the Master level control for the required output level, as indicated by the output peak ...
-
Shure SCM410 - page 9
9 SPECIFICA TIONS Measurement Conditions (unless otherwise specified): Line voltage 120 V ac, 60 Hz (SCM410) or 230 V ac, 50 Hz (SCM410E); full gain; 1 kHz, one channel activated; source impedances: Mic 150 Ω ; terminations: Line/Mic Aux 10 k Ω Frequency Response (at 1 kHz, channel controls centered) 50 Hz to 20 kHz ± 2 dB; -3 dB corner at 25 ...
-
Shure SCM410 - page 10
10 Replacement Parts Knob, Master (white) 95A8238 . . . . . . . . . . . . . . . . . . . . . . . Knob, Channel Gain (blue) 95B8238 . . . . . . . . . . . . . . . . . Line (Power) Cord (SCM410) 95A8762 . . . . . . . . . . . . . . . Line (Power) Cord (SCM410E) 95A8778 . . . . . . . . . . . . . . Link Cable 95A8889 . . . . . . . . . . . . . . . . . . . ...
-
Shure SCM410 - page 11
11 ADV ANCED FUNCTIONS CAUTION : Use of Advanced Functions is recommended only for qualified audio technicians. LOGIC CONNECTION SPECIFICA TIONS The SCM410 logic functions expand the range of installation an d control options. Logic can be used for everything from sim- ple cough switches to elaborate computer-controlled room systems. (Shure’s AMS ...
-
Shure SCM410 - page 12
12 SUGGESTED LOGIC APPLICA TIONS This section contains suggestions on the uses of the SCM410’s logic capabilities. Note that uses of these functions ar e not limited to the listed applications. The user is limited only by imagination and creativity . For additional suggestions and solutions to installation problems, contact the Shure Applica- tio ...
-
Shure SCM410 - page 13
13 Inhibiting Gating for Unwanted Sounds MaxBus attempts to activate only one microphone per sound source. Muting a microphone channel prevents its audio from appearing at the mixer ’ s output. However , the muted micro- phone still communicates with other mic channels via Max- Bus. A sound source picked up by a muted microphone will not activate ...
-
Shure SCM410 - page 14
14 Inhibit Function For information on the inhibit function, refer to the Internal Modifications section. Remote V olume Control Th e level of the Aux or Master output can be controlled from an external VCA (V oltage Controlled Amplifier) such as the RU- VCA1 from Radio Design Labs (T el. 1–800–281–2683, or www .rdlnet.com). T o connect a VCA ...
-
Shure SCM410 - page 15
15 INTERNAL MODIFICA TIONS W ARNING: V oltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel. NOTE: • Only make changes to jumpers (X) and resistors (R). The circuit board contains holes where resistors are to be added. • For Channel modifications, the first charact ...
-
Shure SCM410 - page 16
16 INSERTING AN INPUT LINE P AD T o insert a 40 dB line pad for a given microphone input, remove the resistors specified in the following table. Channel Remove Resistor 1 R1005, R1006 2 R2005, R2006 3 R3005, R3006 4 R4005, R4006 DISABLING THE MASTER LEVEL CONTROL Th e Master gain control can be disabled to prevent tampering. Refer to the following ...
-
Shure SCM410 - page 17
17 When both MUTE IN and OVERRIDE IN logic are grounded, the Override mode will take precedence (as supplied, the MUTE IN takes precedence over OVERRIDE IN). Procedure: 1. Short jumper X1005. 2. Remove resistor R1087. DEAD ZONE ON MUTE IN DEFEA T As supplied, MUTE IN is intended for use as a momentary cough button or privacy function (mute when nec ...
-
Shure SCM410 - page 18
18 This modification is equivalent to shorting one of the channel OVERRIDE IN t o the LOGIC GROUND pin via the high density DB-15 logic connector . With this modification, a channel is al- ways on. Procedure: Short jumper X1003. SHORTING MUTE IN T O LOGIC GROUND INTERNALL Y This modification is equivalent to shorting a channel MUTE IN to the LOGIC ...
Haben Sie eine Frage bezüglich Shure SCM410?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Shure SCM410 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Shure SCM410 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.