Bedienungsanleitung Baldor NEMA 4X

16 Seiten 0.18 mb
Download

Zur Seite of 16

Summary
  • Baldor NEMA 4X - page 1

    ADJUST ABLE SPEED DRIVE Series 5 Inverter NEMA 4X, IP-65 8/01 MN781B Installation & Operating Manual ...

  • Baldor NEMA 4X - page 2

    T ABLE OF CONTENTS Section Page i. Simplified Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ii. Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I. Introduction . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Baldor NEMA 4X - page 3

    i . SIMPLIFIED OPERA TING INSTRUCTIONS W ARNING! Disconnect main power when making connections to the control. A . AC Line Connection – Connect the AC line to L1 and L2 terminals of T erminal Block TB1 and the ground wire (Earth) to the green ground screw as shown in Figure 4, on page 6, and as described in Section IIA, on page 6, and Section IIB ...

  • Baldor NEMA 4X - page 4

    I. INTRODUCTION The Baldor ID5601-BO Adjustable Speed Drive is a variable speed control in a NEMA-4X / IP- 65 and watertight enclosure. It is designed to operate 208 - 230 Volt 3-phase AC induction motors through 3.6 Amps RMS. The sine wave coded Pulse Width Modulated (PWM) output, which operates at a frequency of 8 kHz, provides high motor torque, ...

  • Baldor NEMA 4X - page 5

    3 VIOLET WHITE ORANGE (BACK VIEW) MAIN SPEED POTENTIOMETER (BACK VIEW) START/STOP SWITCH 1. 2. FOR OPTIONAL ID5SI-2 SIGNAL ISOLATOR. ARE USED FOR OPTIONAL R/F, B- AND B+ TERMINALS FWD-STOP-REV SWITCH. REV TERMINAL IS USED RED BLACK WHITE CL BOOST COMP ACCEL DECEL MIN MAX P2 P1 P3 STOP FWD RUN REV COM STOP R/F G B R Y POWER STATUS LED BOARD CON1 J1 ...

  • Baldor NEMA 4X - page 6

    4 POWER ST ATUS REVERSE FORW ARD STOP ST ART POWER 50 40 0 60 70 80 90 100 ON OFF 30 20 10 AUTO MANUAL STOP % SPEED SHOWN WITH OPTIONAL AUTO/MANUAL AND FORWARD-STOP-REVERSE RECOMMENDED MOUNTING SCREW: 1/4" (M6) 2.53 [139.97] 5.51 [128.59] 5.06 [7.97] 0.31 5.86 9.53 [224.00] 8.82 [208.17] 8.20 [241.96] [64.35] [148.94] ADJUST ABLE SPEED DRIVE N ...

  • Baldor NEMA 4X - page 7

    5 II. WIRING INSTRUCTIONS W ARNING! Read Safety W arning, on page 1, before using this control. Disconnect the AC line before wiring. Note: T o avoid erratic operation, do not bundle AC line and motor wires with wires from sig- nal following, Start/Stop Switch or any other signal wires. Use shielded cables on all signal wiring over 12” (30cm). Sh ...

  • Baldor NEMA 4X - page 8

    A. AC Line Connection – Wire the AC line input to L1 and L2 terminals of T erminal Block TB1 as shown in Figure 4. Be sure both Jumpers J1 and J2 are set to the “1 15V” posi- tion for 1 15 V olt AC line input or to the “230V” position for 208/230 V olt AC line input. B. Ground Connection – Earth ground the control chassis using the gree ...

  • Baldor NEMA 4X - page 9

    Note: T o eliminate the Start/Stop function, connect RUN and COM terminals with the jumper that is provided. See Figure 7, on page 6. CAUTION! Using a jumper to eliminate the Start/Stop function will cause the motor to run at the Main Speed Potentiometer setting when the AC line is applied. F . V oltage Following Connection – An isolated 0 - 5 V ...

  • Baldor NEMA 4X - page 10

    8 fault). T o set the control to automatically reset after a fault has been cleared, set Jumper J3 to the "AUTO" position. See Figure 12. (Also see section VIB, on page 9 and T able 4, on page 10.) W ARNING! The motor will automatically restart when the AC line is applied, if Jumper J4 is set to the "AUT O" or “ MAN ” positi ...

  • Baldor NEMA 4X - page 11

    9 B. The hi-pot tester must have an automatic ramp-up to the test voltage and an automatic ramp-down to zero voltage. Note: If the hi-pot tester does not have automatic ramping, then the hi-pot output must be manually increased to the test voltage and then manually reduced to zero. This pro- cedure must be followed for each machine to be tested. A ...

  • Baldor NEMA 4X - page 12

    10 W ARNING! The motor will automatically start when the AC line is applied or a fault is cleared, if Jumper J4 is set to the “ AUT O ” or “ MAN ” position and the Start/Stop Switch is eliminated. VII. AC LINE FUSING This control does not contain AC line fuses. Most electrical codes require that each ungrounded conductor contain circuit pro ...

  • Baldor NEMA 4X - page 13

    11 more rapid deceleration time, rotate the DECEL trimpot coun- terclockwise. For longer deceleration time, rotate the DECEL trimpot clockwise. See Figure 20. Note: T o provide increased resolution of the ACCEL and DECEL trimpots, 50% rotation covers 0.3 - 5 seconds. Application Note: On applications with high inertial loads, the deceleration may a ...

  • Baldor NEMA 4X - page 14

    12 The CL trimpot is factory set for 160% of Jumper J3 range setting. For a higher current limit setting, rotate the CL trimpot clockwise. For a lower current limit setting, rotate the CL trimpot counterclockwise. The current limit also contains I 2 t trip function. The control will trip according to a predetermined current vs. time function. The t ...

  • Baldor NEMA 4X - page 15

    IX. DIAGNOSTIC LEDs The motor control is designed with LEDs mounted on the front cover to display the control’s operational status. A . Power On (ON) – Indicates the presence of bus voltage. B. Status (ST A TUS) – The Status LED is a tricolor LED that provides indication of the con- trol’s operational status including installation problems ...

  • Baldor NEMA 4X - page 16

    (A40299) – Rev . A – 3/2001 XI. LIMITED W ARRANTY For a period of 2 years from date of original purchase, BALDOR will repair or replace without charge controls which our examination proves to be defective in material or workmanship. This warranty is valid if the unit has not been tampered with by unauthorized persons, mis- used, abused, or impr ...

Produzent Baldor Kategorie Power Supply

Dokumente, die wir vom Produzenten des Geräts Baldor NEMA 4X erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Baldor
- Bedienungsanleitungen NEMA 4X
- Produktkarten Baldor
- Informationsbroschüren
- oder Energieetiketten Baldor NEMA 4X
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Baldor NEMA 4X.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Baldor NEMA 4X, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Baldor NEMA 4X. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Baldor NEMA 4X ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Baldor NEMA 4X, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Baldor NEMA 4X hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Baldor NEMA 4X verständlich ist.

Eine gänzliche Bedienungsanleitung von Baldor sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Baldor NEMA 4X bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Baldor NEMA 4X befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Baldor NEMA 4X, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Baldor NEMA 4X - die uns die ersten Schritte während der Nutzung von Baldor NEMA 4X erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Baldor NEMA 4X hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Baldor NEMA 4X im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Baldor NEMA 4X?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Baldor NEMA 4X nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Baldor NEMA 4X hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)