Deutsch dropdown-ico

Bedienungsanleitung Brinkmann 2600 Series

32 Seiten 1.29 mb
Download

Zur Seite of 32

Summary
  • Brinkmann 2600 Series - page 1

    OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW M A X I M U M S I D E B U R N E R L O A D = 1 5 l b s . 1. Read and follow all warnings and instructions in owner’s manual before lighting. 2. Open lid before lighting burner. 3. Make sure all control knobs are in the OFF position. 4. Select the burner to be lit. Push and turn the control knob o ...

  • Brinkmann 2600 Series - page 2

    WE W ANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFEL Y AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO A TTRACT YOUR A TTENTION T O POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL. WHEN YOU SEE THE SAFETY ALERT SYMBOL P A Y CLOSE A TTENTION TO THE INFORMA TION WHICH FOLLOWS! READ ALL SAFETY W ARNINGS AND INSTRUCTIONS CAREFULL Y BEFOR ...

  • Brinkmann 2600 Series - page 3

    2 W ARNING • Never use natural gas in a unit designed for liquid propane gas. • Never use charcoal briquets or lighter fluid in a gas grill. • Leak test all connections before first use, even if grill was purchased fully assembled and after each tank refill. • Never check for leaks using a match or open flame. CAUTION! Strong odors, colds, ...

  • Brinkmann 2600 Series - page 4

    CYLINDER SPECIFICA TIONS: When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of T ransportation (DOT) or the National Standard of Canada, CAN/CSA-B339 as applicable with a listed over-filling prevention device (OPD). 3 W ARN ...

  • Brinkmann 2600 Series - page 5

    4 The cylinder must also be equipped with: • A shut-off valve terminating in a T ype 1 gas cylinder valve outlet. • A T ype 1 valve that prevents gas flow until a positive seal is obtained. • An arrangement for vapor withdrawal. • A collar to protect the cylinder shut-off valve. • A safety relief device having direct communication with th ...

  • Brinkmann 2600 Series - page 6

    W ARNING FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder . • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be filled beyond 80% capacity . Over-filled tanks can create a dangerous condition. Over-f ...

  • Brinkmann 2600 Series - page 7

    6 W ARNING • Never use your grill without leak testing all gas connections and hoses. See the section on "Leak T esting" in this manual for proper procedures. The pressure regulator and hose assembly supplied with your gas grill is designed to work with an LP gas supply cylinder . • DO NOT attempt to connect it to any other fuel suppl ...

  • Brinkmann 2600 Series - page 8

    LEAK TESTING: T o prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the grill is in use or while grill is still hot. WHEN TO PER ...

  • Brinkmann 2600 Series - page 9

    W ARNING 8 6. Check each place listed (A -K) for growing bubbles which indicates a leak. 7. Turn OFF gas supply at cylinder valve. 8. Turn on control knobs to release gas pressure in hose. 9. Turn control knobs to OFF position. 10. Tighten any leaking connections. 1 1. Repeat soapy water test until no leaks are detected. DO NOT use the grill if lea ...

  • Brinkmann 2600 Series - page 10

    LIGHTING INSTRUCTIONS: Follow the instructions exactly . 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the OFF position. 3. T urn on the fuel supply by rotating the ...

  • Brinkmann 2600 Series - page 11

    LIGHTING THE SIDE BURNER: 1. Open lid to the side burner before lighting. 2. T urn on the side burner by pressing in and rotating the control knob to the HIGH position. 3. Press and hold the igniter button on the main control panel for 3-5 seconds until the burner ignites. 4. If burner does not ignite immediately , turn the burner control knob to O ...

  • Brinkmann 2600 Series - page 12

    11 OPERA TING THE GRILL: Never use Charcoal or Lighter Fluid inside your Gas Grill. Read and follow all warnings and instructions contained in the preceding sections of this manual. BREAKING IN YOUR GRILL: • In manufacturing and preserving the components of your grill, oil residue may be present on the burner and cooking surfaces of your grill. ? ...

  • Brinkmann 2600 Series - page 13

    ROTISSERIE COOKING: • Y our grill was pre-drilled from factory to include mounting holes for a Brinkmann rotisserie (sold separately). Do not use a rotisserie not specifically manufactured for this grill. • Read and follow all instructions provided with the rotisserie. Save instructions for future reference. • Do not use the side burner when ...

  • Brinkmann 2600 Series - page 14

    TRANSPORTING AND STORAGE: • Never move a grill when it is hot or when objects are on the cooking surfaces. • Make sure that cylinder valve is shut off. After moving the grill check that all gas connections are free of leaks. Refer to instructions for leak test on page 7 of this manual. • DO NOT store a spare LP gas cylinder (filled or empty) ...

  • Brinkmann 2600 Series - page 15

    CLEANING AND MAINTENANCE: • For safe grilling and peak performance of your grill, perform these checks at least twice per year or after extended periods of storage. HARDW ARE • Be sure to tighten up all hardware (nuts, bolts, screws, etc.) at least twice per year . CASTINGS • Remove the cooking grills, heat shields, and burners from inside yo ...

  • Brinkmann 2600 Series - page 16

    TROUBLE SHOOTING: Problem: Possible Causes: • Burner will not light 1. Check LP cylinder fuel level. 2. Bad electrode spark. Check to see if the grill will “ match light. ” (See Page 9) Electrode or collector may need adjustment. 3. Burner may not be properly seated. 4. Burner may be obstructed. 5. The cylinder valve may be closed. 6. Regulat ...

  • Brinkmann 2600 Series - page 17

    16 • T o protect your grill from excessive rust, the unit must be kept clean and covered at all times when not in use. A grill cover may be ordered directly from Brinkmann by calling 1-800-468-5252 or 1-800-527-0717. • W ash cooking grills and heat shields with hot, soapy water , rinse well and dry . Lightly coat cooking grill with vegetable oi ...

  • Brinkmann 2600 Series - page 18

    ASSEMBL Y INSTRUCTIONS READ ALL SAFETY W ARNINGS & ASSEMBL Y INSTRUCTIONS CAREFULL Y BEFORE ASSEMBLING OR OPERA TING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT . The following provided tools are required to assemble this Brinkmann Pro Series 2600 Grill: • Flathead Screwdriver • Hex Nut Wrench 17 1 Electronic ...

  • Brinkmann 2600 Series - page 19

    (Proof of purchase will be required.) Inspect contents of the box to ensure all parts are included and undamaged. 1 FOR MISSING P ARTS, PLEASE CALL CUSTOMER SER VICE A T 1-800-527-0717. 18 2 3 4 5 6 7 8 9 10 24 11 13 12 14 15 16 17 18 19 20 21 22 23 27 25 26 28 15 29 30 31 32 33 34 35 36 37 ...

  • Brinkmann 2600 Series - page 20

    19 8 M6 X 12mm bolts 8 M6 X 20mm bolts 14 M6 X 60mm bolts 1 AA /1.5V Alkaline battery P AR TS CARD CONTENTS Make sure you have all items listed under P ARTS LIST and P ARTS BAG CONTENTS before you begin the installation process. Y our Parts Bag will include: M6 X 12mm bolts M6 X 20mm bolts M6 X 60mm bolts AA /1.5V Alkaline battery Screwdriver Hex n ...

  • Brinkmann 2600 Series - page 21

    Choose a good, cleared assembly area and get a friend to help you put your grill together . Lay cardboard down to protect grill finish and assembly area. Step 1 Assemble bottom cart panel and right side cart panel assembly by using four M6 X 60mm bolts (hand tighten only at this point). Step 2 Assemble bottom cart panel and left side cart panel ass ...

  • Brinkmann 2600 Series - page 22

    Note: With the help of a friend, turn the cart over , try to minimize the stress to the side panels. Step 3 Attach locking casters to the bottom of the cart. T ighten caster bolts securely using hex nut wrench provided in parts pack. Note: With the help of a friend, turn the cart to its upright position. Step 4 Attach back car t panel by using six ...

  • Brinkmann 2600 Series - page 23

    22 Step 5 Place tank tray assembly over vent holes in bottom cart panel and secure using four M6 X 12mm bolts. T ank tray should slide in and out of cart freely . Step 6 Install door bracket using the four #10 X 1/2 ” self taping screws. Make sure door stop is set toward back of cart. Wing Bolt Center Cut-out T ank T ray Assembly Door bracket ...

  • Brinkmann 2600 Series - page 24

    23 Step 7 Insert right side door , placing lower pivot into the pivot hole on bottom cart panel, then align door with cart frame. Depress spring pin located on top edge of door and slide door toward side cart panel until spring pin locks into hole in door bracket. Repeat for other door . Step 8 Attach the grease tray bracket onto the back cart pane ...

  • Brinkmann 2600 Series - page 25

    Note: When performing Step 9, Lift grill body from front and rear panels to avoid injury to hands and fingers. Step 9 With the help of a friend, place grill body assembly on grill cart. Grill body will rest between upper side sections of cart. Align front edge of grill body assembly with front edges of cart frame legs. Secure using four M6 X12mm bo ...

  • Brinkmann 2600 Series - page 26

    25 Step 10 Attach side burner assembly to grill body assembly by inserting four M6 X 20mm bolts through the holes in the side burner assembly and into holes of grill body assembly . T ighten all four bolts. Install side burner grate and control knob. Step 1 1 Remove the plastic cap on gas supply manifold and attach rubber gas hose to gas supply man ...

  • Brinkmann 2600 Series - page 27

    Step 13 Attach side table/ice bucket assembly to grill body assembly by inserting four M6 X 20mm bolts through the holes in the side table/ice bucket assembly and into holes of grill body assembly . T ighten all four bolts. Step 14 Insert tool drawer into front opening under control panel by dropping roller wheels into side channels. W arning: DO N ...

  • Brinkmann 2600 Series - page 28

    Step 15 Insert grill bottom into opening on backside of grill. Make sure to slide tray onto tracks as illustrated. Step 16 Slide grease tray into grease tray bracket located under grill bottom on backside of grill. Step 17 Hang stainless steel bucket in cut- out of left side table/ice bucket assembly . Step 18 Place ice bucket insulation around sta ...

  • Brinkmann 2600 Series - page 29

    28 Step 19 Place the porcelain coated heat shields on lower level of grill body assembly directly above burners. Step 20 Place porcelain cast iron cooking grills on support ribs directly above porcelain heat shields. Step 21 Place warming rack in slots above cast iron cooking grills. W arming Rack Cooking Grills Porcelain Heat Shields Pro Series 26 ...

  • Brinkmann 2600 Series - page 30

    PROFESSIONAL SHISH-KABOB SKEWERS These heavy-duty , 18" shish-kabob skewers are extra-long for fabulous restaurant style kabobs. Made of rust resistant stainless steel to last for years. SET OF 12 812-2904-0 ACCESSORIES 29 RIB RACK Chrome-plated rack can greatly increase the cooking capacity of your grill. Holds ribs, chicken halves, potatoes ...

  • Brinkmann 2600 Series - page 31

    ACCESSORIES LOOK FOR THESE AND OTHER BRINKMANN ACCESSORIES A T YOUR LOCAL RET AILER WHERE SMOKERS ARE SOLD, OR ORDER DIRECT BY CALLING 1-800-468-5252. THE UL TIMA TE 5-PIECE BBQ TOOL SET Yo u ’ ll be the envy of your fellow outdoor chefs with this ultimate BBQ tool set. It ’ s sleek ergonomic design combined with durable, heavy- gauge stainless ...

  • Brinkmann 2600 Series - page 32

    140-2601-1 8/02, 10/03 , 10/05 W ARRANTY ©2002 The Brinkmann Corporation Dallas, T exas 75244 U.S.A www .brinkmann .net The Brinkmann Corporation warrants to the original purchaser that the Brinkmann Stainless Steel Pro Series 2600 TM is free from defects due to workmanship or materials for: Stainless steel and die cast parts - Lifetime Electronic ...

Produzent Brinkmann Kategorie Gas Grill

Dokumente, die wir vom Produzenten des Geräts Brinkmann 2600 Series erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Brinkmann
- Bedienungsanleitungen 2600 Series
- Produktkarten Brinkmann
- Informationsbroschüren
- oder Energieetiketten Brinkmann 2600 Series
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Brinkmann 2600 Series.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Brinkmann 2600 Series, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Brinkmann 2600 Series. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Brinkmann 2600 Series ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Brinkmann 2600 Series, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Brinkmann 2600 Series hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Brinkmann 2600 Series verständlich ist.

Eine gänzliche Bedienungsanleitung von Brinkmann sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Brinkmann 2600 Series bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Brinkmann 2600 Series befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Brinkmann 2600 Series, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Brinkmann 2600 Series - die uns die ersten Schritte während der Nutzung von Brinkmann 2600 Series erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Brinkmann 2600 Series hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Brinkmann 2600 Series im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Brinkmann 2600 Series?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Brinkmann 2600 Series nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Brinkmann 2600 Series hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)