Bedienungsanleitung JBL A3000GTI

12 Seiten 0.54 mb
Download

Zur Seite of 12

Summary
  • JBL A3000GTI - page 1

    car audio pow er amplifier owner’ s manual THANK Y OU for purchasing a JBL A6000GT i or A3000GT i amplifier . For warranty support, please register your purchase at www.jbl.com. Select Car Audio, then click on Support, and then click on Product Registration. Also, please retain your original purchase receipt and packing crate in case you must shi ...

  • JBL A3000GTI - page 2

    INST ALLA TION W ARNING: Playing loud music in an automobile can hinder your ability to hear traffic and permanently damage your hearing. We recommend listening at low or moderate levels while driving your car . JBL accepts no liability for hearing loss, bodily injury or property damage resulting from the use or misuse of this product. IMPORT ANT : ...

  • JBL A3000GTI - page 3

    DESIGNING A SPEAKER SY STEM FOR THE GTI AMPLIFIER NOTE: Although the JBL A6000GT i or A3000GT i amplifier will drive a system made up of any subwoofers, we recommend using JBL GT i subwoofers with GT i amplifiers. Both the JBL A6000GT i and A3000GT i amplifiers provide RMS power that exceeds the RMS power-handling rating of nearly every subwoofer a ...

  • JBL A3000GTI - page 4

    4 SUPPL YING POWER TO THE GTI AMPLIFIER POWER IN IS POWER OUT In order to get full power out of your amplifier , you must provide full power to your amplifier . That’ s a basic rule of physics. The A6000GT i amplifier can draw nearly 800 amperes when reproducing sine waves at full output. Both JBL A6000GT i and A3000GT i ampli- fiers can quickly ...

  • JBL A3000GTI - page 5

    5 MAKING THE CONNECTIONS POWER CONNECTIONS Use 0-gauge cable to connect the amplifier’ s GND – terminal directly to the vehicle’ s chassis (see Figure 5). Scrape off all paint from the metal area for a good, clean ground connection. Make sure the ground wire is as short as possible and is connected to metal on the vehicle’ s body. Do not co ...

  • JBL A3000GTI - page 6

    6 MAKING THE CONNECTIONS A6000GTi SPEAKER CONNECTIONS The A6000GT i is a 2-channel amplifier designed to drive subwoofers only . The left and right input signals are com- bined inside the amplifier to provide a mono output signal, no matter which output mode is selected. The A6000GT i can be connected to two independent speaker systems in 2-channel ...

  • JBL A3000GTI - page 7

    7 MAKING THE CONNECTIONS A3000GTI SPEAKER CONNECTIONS Included below are three application diagrams that will help you plan your A3000GT i installation. Figures 10 through 12 show how to configure the JBL A3000GT i amplifier for bridged-mono, parallel-mono and 2-channel operation (also see Setting Up the GT i Amplifier). NOTE: For simplicity , Figu ...

  • JBL A3000GTI - page 8

    8 SETTING UP THE GTI AMPLIFIER SETTING INPUT SENSITIVITY NOTE: Y ou can use the supplied REMOTE LEVEL control to fine-tune the input sensitivity or to adjust the level of the bass according to the program material after the amplifier’ s LEVEL control has been set properly . Connect the remote module’ s attached cable to the REMOTE LEVEL (RJ45) ...

  • JBL A3000GTI - page 9

    9 SETTING UP THE GTI AMPLIFIER REPLACING THE FUSE OR NEON TUBES The JBL A6000/A3000GT i amplifier is equipped with an internal fuse, a 20-inch neon tube and two 6-inch neon tubes. Should the fuse or a neon tube fail, perform the following steps to replace the part: NOTE: For neon tube replacement, see your authorized JBL car audio dealer to purchas ...

  • JBL A3000GTI - page 10

    10 SETTING UP THE GTI AMPLIFIER 7. Using a T -15 screwdriver , remove the two T orx-head screws on the display board and set them aside (see Figure 16 below). Disconnect the ribbon cable from display board. 8. Using a T -15 screwdriver , remove the 16 T orx-head screws on the perforated shield and set them aside (see Figure 16). Figure 16. Removing ...

  • JBL A3000GTI - page 11

    11 TROUBLESHOOTING SYMPTOM LIKEL Y CA USE SOLUTION No audio No voltage at power Check BA TT+, REMOTE and (Power LED is off) or remote terminal GND – terminals with VOM for blown fuse or poor connection Internal fuse blown Replace internal fuse (incorrect power (see Replacing the Fuse connections) or Neon T ubes section) No audio Low or high volta ...

  • JBL A3000GTI - page 12

    Declaration of Conf or mity We, Har man Consumer Group Inter national 2, route de T ours 72500 Chateau-du-Loir Fr ance declare in own responsibility that the products described in this owner’s man ual are in compliance with technical standards: EN 55013:2001 EN 55020:2002 Emmanuel Millot Harman Consumer Group Inter national Chateau-du-Loir, F ran ...

Produzent JBL Kategorie Car Amplifier

Dokumente, die wir vom Produzenten des Geräts JBL A3000GTI erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen JBL
- Bedienungsanleitungen A3000GTI
- Produktkarten JBL
- Informationsbroschüren
- oder Energieetiketten JBL A3000GTI
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung JBL A3000GTI.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen JBL A3000GTI, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen JBL A3000GTI. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts JBL A3000GTI ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts JBL A3000GTI, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von JBL A3000GTI hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von JBL A3000GTI verständlich ist.

Eine gänzliche Bedienungsanleitung von JBL sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von JBL A3000GTI bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von JBL A3000GTI befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich JBL A3000GTI, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts JBL A3000GTI - die uns die ersten Schritte während der Nutzung von JBL A3000GTI erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit JBL A3000GTI hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von JBL A3000GTI im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich JBL A3000GTI?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit JBL A3000GTI nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit JBL A3000GTI hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)