Deutsch dropdown-ico

Bedienungsanleitung Weider WESY96400

34 Seiten 0.91 mb
Download

Zur Seite of 34

Summary
  • Weider WESY96400 - page 1

    USER'S MANUAL P A TENT PENDING QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete sat- isfaction through direct assis- tance from our factory . TO A VOID UNNECESSARY DELA YS, PLEASE CALL DIRECT TO O ...

  • Weider WESY96400 - page 2

    2 T ABLE OF CONTENTS LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . ...

  • Weider WESY96400 - page 3

    3 IMPORT ANT PRECAUTIONS W ARNING: T o reduce the risk of serious injury , read the following important precautions before using the home gym system. W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all inst ...

  • Weider WESY96400 - page 4

    4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76 in. Width: 89 in. Length: 64 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Military Press Arm Press Arm Weight Stacks Backrests VKR Arms Leg Press Plate Thank you for selecting the versatile WEIDER ® PRO 9640 Home Gym System. The PRO 9640 of fers a selecti ...

  • Weider WESY96400 - page 5

    5 ASSEMBL Y 1 8 11 51 27 1 4 3 1 51 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press two 2” Square Outer Caps (51) onto the indicated locations on the Stabilizer (5). Press a 2” Square Inner Cap (27) into the end of ...

  • Weider WESY96400 - page 6

    6 2. Slide the VKR Upright (74) and the Leg Press Upright (56) onto the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the VKR Upright and Leg Press Upright should be on the side shown. Hand-tighten four 5/16” Nylon Locknuts (3) onto the Carriage Bolts. Do not tighten the Nylon Locknuts yet ...

  • Weider WESY96400 - page 7

    7 4. Press a 2” Square Inner Cap (27) into the end of the T op Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the T op Frame. Press two 1” Round Inner Caps (49) into the top of the crossbar . Attach the T op Frame (55) to the VKR Upright (74) and the Leg Press Upright (56) with two 5/16” x 2 3/4” Bolts ( ...

  • Weider WESY96400 - page 8

    8 7. Press a Weight T ube Bumper (64) into the end of a Weight T ube (63). Insert the Weight T ube into the front stack of Weights (25). Be sure that the pin on the Weight T ube is sit- ting in the pin grooves in the top Weight. Lubricate the inside of the holes in a T op Weight (65). Set the T op Weight onto the front stack of Weights (25). Insert ...

  • Weider WESY96400 - page 9

    9 9. Attach the upper ends of the Short Weight Guides (73) to the T op Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Lockn ...

  • Weider WESY96400 - page 10

    10 12. Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3). Assemble the other Press Arm (46) in the same manner . 13. Identify the Right Ar ...

  • Weider WESY96400 - page 11

    11 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (101) with two 5/16” x 2 1/4” Bolts (33) and two 5/16” Nylon Locknuts (3). Press two 1 1/2” Square Inner Caps (32) into the indicated end of the Military Press Arm (84). Press two 1” Round Inner Caps (49) into the Military Press Arm. Slide two 5” Plastic G ...

  • Weider WESY96400 - page 12

    12 18. Wrap the High Cable (58) around a “V”-Pulley (50). Attach the “V”-Pulley and a Long Cable T rap (31) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the Long Cable T rap is positioned to hold the Cable in place. 19. Route the High Cable (58) around th ...

  • Weider WESY96400 - page 13

    13 22. See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable T rap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable T rap is inside the Long “U”- Bracket. Note: This may come pre-assem- bled. Route the High Cable (58) through the Long “U”- ...

  • Weider WESY96400 - page 14

    14 25. Locate the Low Cable (23). Route the Low Cable under the 3 1/2” Low Pulley (76) attached to the lower hole in the Press Frame (17). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame and that the Cable is between the Pulley and the crossbar on the Press Frame. T ighten the 3/8” Nylon Locknut (21) ...

  • Weider WESY96400 - page 15

    15 29. Attach the end of the Low Cable (23) to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing. 30. Attach the High ...

  • Weider WESY96400 - page 16

    16 32. Wrap the Military Press Cable (72) around a 3 1/2” Pulley (15). Attach the Pulley to the T op Frame (55) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). See the inset drawing. Wrap the Long Cable (72) around a 3 1/2” Pulley (15). Attach the Pulley and a Cable T rap (66) to the bracket on the Stabilizer (5) with a 3/8” x ...

  • Weider WESY96400 - page 17

    17 34. See inset drawing A. Attach a 3 1/2” Pulley (15) and a Cable T rap (66) to the upper hole in the Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable T rap is inside the Long “U”-Bracket. (Note: This may come pre- assembled. ) Route the Military Press Cable (72) through the Lo ...

  • Weider WESY96400 - page 18

    18 36. Attach the Press Bracket (94) to the Leg Press Arm (96) with a 5/16” x 3” Bolt (75) and a 5/16” Nylon Locknut (3). Wrap the Leg Press Cable (99) around a 3 1/2” Pulley (15). Attach the Pulley to the Press Bracket (94) with the 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Slide a 5/16” Flat W asher (8) onto a 5/16” x 2 ...

  • Weider WESY96400 - page 19

    19 39. Attach the Front Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Flat W ashers (10). The Backrest must be oriented as shown. 40. Press a 1 1/2” Square Inner Cap (32) into the Front Seat Frame (36). Insert a 1/4” x 2” Carriage Bolt (38) through the center hole in the Seat Plate (37). Attach ...

  • Weider WESY96400 - page 20

    20 43. Press two 3/4” Round Inner Caps (34) into each Pad T ube (28). Insert a Pad T ube (28) into the Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Foam Pad (30) onto each end of the Pad T ube. 44. Locate and open the parts bag labeled “VKR ASSEMBL Y ...

  • Weider WESY96400 - page 21

    21 46. Remove the adhesive backing from the PRO 9640 decal and apply it to the Front Upright (42) under the “WEIDER” nameplate as shown. 47. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW T O USE THE HOME GYM SYSTEM, beginning on page 22 of this manual. Before using the home gym sy ...

  • Weider WESY96400 - page 22

    22 HOW T O USE THE HOME GYM SYSTEM The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPORT ANT : When attaching the lat bar or nylon strap, make sure that the attachments are in the cor- rect ...

  • Weider WESY96400 - page 23

    23 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed. First, be sure that the chain i ...

  • Weider WESY96400 - page 24

    24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. WEIGHT PRESS BUTTERFL Y LEG HIGH LOW MILIT ARY LEG ARM ARM LEVER PULL ...

  • Weider WESY96400 - page 25

    TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the home gym system, can stretch slightly ...

  • Weider WESY96400 - page 26

    26 CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the home gym sys- tem ...

  • Weider WESY96400 - page 27

    27 Military Press Cable (72) Leg Press Cable (99) Rear Weight Stack— 1 2 3 4 5 3 2 4 — Rear Seat Frame 6 — Pivot Arm 1 — Long “U”-Bracket Military Press Cable (72) and Leg Press Cable (99) ...

  • Weider WESY96400 - page 28

    ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (WESY96400). 2. The NAME ...

  • Weider WESY96400 - page 29

    WESY96400 R1296A Please Note: The assembly is divided into five stages: 1) frame assembly , 2) arm assembly , 3) cable and pulley assembly , 4) seat and backrest assembly , and 5) VKR assembly . The hardware for each stage is packaged separately . W AIT UNTIL YOU BEGIN EACH ASSEMBL Y ST AGE T O OPEN THE P ARTS BAG LABELED FOR THA T ASSEMBL Y ST AGE ...

  • Weider WESY96400 - page 30

    1" Round Inner Cap (49)–8 1" Round Cover Cap (70)–2 3/4" Round Inner Cap (34)–4 1/2" x 3/4" Spacer (61)–4 5/16" x 2" Eyebolt (35)—1 1 1/2" Square Inner Cap (32)–6 1 3/4" Square Inner Cap (44)–6 2" Square Inner Cap (27)–8 2" Square Outer Cap (51)–2 1" Square Inner Cap (6)? ...

  • Weider WESY96400 - page 31

    5/16" Nylon Locknut (3)–34 1/4" Flat Washer (10)–17 5/16" Flat Washer (8)–9 1" Retainer (69)–4 3/8" Flat Washer (9)–6 1/4" x 2 1/2" Screw (43)–6 3/8" Nylon Locknut (21)–20 1/4" x 2" Machine Screw (81)–5 5/16" Nylon Jam Nut (93)–4 5/16" x 2 1/2" Carriage Bolt (1)–10 ...

  • Weider WESY96400 - page 32

    REMOVE THIS P AR T LIST/EXPLODED DRA WING FROM THE MANUAL! 81 ...

  • Weider WESY96400 - page 33

    P ART LIST—Model No. WESY96400 R1296A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty . Description 1 10 5/16” x 2 1/2” Carriage Bolt 2 6 1/4” Nylon Locknut 3 34 5/16” Nylon Locknut 4 1 Base 5 1 Stabilizer 6 1 1” Square Inner Cap 7 1 5/8” x 9/16” Spacer 8 9 5/16” Fla ...

  • Weider WESY96400 - page 34

    60 27 21 15 55 12 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 63 64 25 26 19 21 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 48 50 31 86 13 40 38 37 18 32 34 30 28 3 49 83 33 10 2 36 14 88 15 29 35 30 34 34 30 28 3 8 32 30 34 10 49 49 81 88 44 44 83 66 66 66 90 89 89 7 3 1 1 ...

Produzent Weider Kategorie Home Gym

Dokumente, die wir vom Produzenten des Geräts Weider WESY96400 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Weider
- Bedienungsanleitungen WESY96400
- Produktkarten Weider
- Informationsbroschüren
- oder Energieetiketten Weider WESY96400
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Weider WESY96400.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Weider WESY96400, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Weider WESY96400. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Weider WESY96400 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Weider WESY96400, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Weider WESY96400 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Weider WESY96400 verständlich ist.

Eine gänzliche Bedienungsanleitung von Weider sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Weider WESY96400 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Weider WESY96400 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Weider WESY96400, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Weider WESY96400 - die uns die ersten Schritte während der Nutzung von Weider WESY96400 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Weider WESY96400 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Weider WESY96400 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Weider WESY96400?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Weider WESY96400 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Weider WESY96400 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)