Deutsch dropdown-ico

Bedienungsanleitung SUPER MICRO Computer SYSF617R2RT

87 Seiten 38.61 mb
Download

Zur Seite of 87

Summary
  • SUPER MICRO Computer SYSF617R2RT - page 1

    SCF418 Chassis Series USER’S MANUAL 1.0 S UPER ® SCF418BC-R1K62BP SCF418IF-R1K62BP SCF418IL-R1K62BP ...

  • SUPER MICRO Computer SYSF617R2RT - page 2

    SCF418 Chassis Manual ii Manual Revision 1.0 Release Date: April 1 1, 2013 The information in this User ’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this man ...

  • SUPER MICRO Computer SYSF617R2RT - page 3

    iii Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SCF418 4U chassis. Instal - lation and maintenance should be performed by experienced technicians only . The FatT win™ is the latest addition to Supermicro's evolving ...

  • SUPER MICRO Computer SYSF617R2RT - page 4

    SCF418 Chassis Manual iv Manual Organization Chapter 1 Introduction Chapter 1 describes components included with this chassis, and the main features of the SCF418 chassis. This chapter also includes contact information. Chapter 2 System Safety This chapter lists warnings, precautions, and system safety . Y ou should thoroughly familiarize yourself ...

  • SUPER MICRO Computer SYSF617R2RT - page 5

    v Preface Appendix A Power Supply Specications Appendix B SAS-F418-B6 Backplane Specications Appendix C SAS-F418-B2R Backplane Specications ...

  • SUPER MICRO Computer SYSF617R2RT - page 6

    SCF418 Chassis Manual vi T able of Contents Preface About This Manual ............................................................................................. iii Manual Organization .......................................................................................... iv Chapter 1 Introduction 1-1 Overview ................................ ...

  • SUPER MICRO Computer SYSF617R2RT - page 7

    vii Preface Chapter 5 Chassis Setup and Maintenance 5-1 Overview ......................................................................................................... 5-1 5-2 Installation Procedures .................................................................................... 5-1 5-3 Removing Power Cords ................................. ...

  • SUPER MICRO Computer SYSF617R2RT - page 8

    SCF418 Chassis Manual viii Chapter 6 Rack Installation 6-1 Overview ......................................................................................................... 6-1 6-2 Unpacking the System .................................................................................... 6-1 6-3 Preparing for Setup .................................. ...

  • SUPER MICRO Computer SYSF617R2RT - page 9

    1-1 Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview Supermicro's SCF418 "Fat T win" chassis is designed to optimize performance per W att and per dollar with up to eight independent hot-pluggable DP computing nodes, efciently organized into a 4U form factor . Each node provides hot-swappable and/ or xed hard drives ...

  • SUPER MICRO Computer SYSF617R2RT - page 10

    SCF418 Chassis Manual 1-2 1-3 Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (T echnical Support) Web Site: www .supermicro.com Europe Address: Super Micro Compu ...

  • SUPER MICRO Computer SYSF617R2RT - page 11

    1-3 Chapter 1: Introduction 1-4 Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required be - fore any warranty service will be rendered. Y ou can obtain service by calling your vendor for a Returned Merchandise Authorization (RMA) number . When returning to the manufacturer , the RMA number s ...

  • SUPER MICRO Computer SYSF617R2RT - page 12

    2-1 Chapter 2: W arning Statements for AC Systems Chapter 2 Standardized W arning Statements for AC Systems 2-1 About Standardized W arning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury . Should you have questions or experience difficulty , cont ...

  • SUPER MICRO Computer SYSF617R2RT - page 13

    2-2 S UPER S ERVER "servername" User's Manual W arnung WICHTIGE SICHERHEITSHINWEISE Dieses W arnsymbol bedeutet Gefahr . Sie benden sich in einer Situation, die zu V erletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen V erfahren zur V orbeugung vor Unfä ...

  • SUPER MICRO Computer SYSF617R2RT - page 14

    2-3 W arning Statements for AC Systems 안전을 위한 주의사항 경고! 이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험요소들을 확인하시고 사전에 사고 ...

  • SUPER MICRO Computer SYSF617R2RT - page 15

    2-4 S UPER S ERVER "servername" User's Manual Installation Instructions W arning! Read the installation instructions before connecting the system to the power source. W arnung V or dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar ...

  • SUPER MICRO Computer SYSF617R2RT - page 16

    2-5 Chapter 2: W arning Statements for AC Systems Circuit Breaker W arning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V , 20 A. サー キ ッ ト ・ ブレ ーカー こ の製品は、 短絡 （過電流 ） 保護装置が ...

  • SUPER MICRO Computer SYSF617R2RT - page 17

    2-6 S UPER S ERVER "servername" User's Manual Power Disconnection W arning 電源切断の警告 システムコン ポ ー ネン トの 取り 付 けまた は 取り外しの た め に、 シャーシ ー 内 部 にア クセ ス する に は 、 シ ステムの 電 源 はす べ てのソースから切 断され 、 電 ...

  • SUPER MICRO Computer SYSF617R2RT - page 18

    2-7 Chapter 2: W arning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché de ...

  • SUPER MICRO Computer SYSF617R2RT - page 19

    2-8 S UPER S ERVER "servername" User's Manual Equipment Installation 機器の設置 ト レ ーニン グを受け認 定さ れた人だけが こ の装 置の 設 置、 交換、 ま たはサー ビ ス を許 可 されています 。 W arning! Only trained and qualied personnel should be allowed to install, replace, or se ...

  • SUPER MICRO Computer SYSF617R2RT - page 20

    2-9 Chapter 2: W arning Statements for AC Systems ア ク セ ス制限区域 こ のユニ ッ ト は 、 ア ク セ ス制限区域に 設置 さ れ る こ と を想定 し て い ま す 。 ア ク セ ス制限区域 は、 特別 な ツー ル、 鍵 と 錠前、 そ の他の セキ ュ リ テ ィ の手段を 用い て の み出? ...

  • SUPER MICRO Computer SYSF617R2RT - page 21

    2-10 S UPER S ERVER "servername" User's Manual Battery Handling W arning! There is the danger of explosion if the battery is replaced incorrectly . Replace the battery only with the same or equivalent type recommended by the manufacturer . Dispose of used batteries according to the manufacturer's instructions תלבגומ השי ...

  • SUPER MICRO Computer SYSF617R2RT - page 22

    2-1 1 Chapter 2: W arning Statements for AC Systems W arnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr . Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'es ...

  • SUPER MICRO Computer SYSF617R2RT - page 23

    2-12 S UPER S ERVER "servername" User's Manual W arnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle V erbindungen entfernt werden. ¡Advertencia! Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para cortar por complet ...

  • SUPER MICRO Computer SYSF617R2RT - page 24

    2-13 Chapter 2: W arning Statements for AC Systems Backplane V oltage バッ ク プレ ーン の 電 圧 シ ス テ ムの稼 働中 は危険な電 圧 ま た は電 力が、 バ ッ ク プ レー ン上にかか っ て い ま す 。 修 理 する 際 に は 注 意く だ さい 。 警告 当系统正在进行时，背板上有很危? ...

  • SUPER MICRO Computer SYSF617R2RT - page 25

    2-14 S UPER S ERVER "servername" User's Manual Comply with Local and National Electrical Codes W arning! Installation of the equipment must comply with local and national electrical codes. 地方お よ び国の電気規格に 準拠 機器の取 り 付け は その地方お よ び国の電気規格に準拠す る 必要があ ? ...

  • SUPER MICRO Computer SYSF617R2RT - page 26

    2-15 Chapter 2: W arning Statements for AC Systems Product Disposal W arning! Ultimate disposal of this product should be handled according to all national laws and regulations. יצראה למשחה יקוח םואית !הרהזא תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תביי ח ד ויצה .  ...

  • SUPER MICRO Computer SYSF617R2RT - page 27

    2-16 S UPER S ERVER "servername" User's Manual W aarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le r ...

  • SUPER MICRO Computer SYSF617R2RT - page 28

    2-17 Chapter 2: W arning Statements for AC Systems W arnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger , Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ve ...

  • SUPER MICRO Computer SYSF617R2RT - page 29

    2-18 S UPER S ERVER "servername" User's Manual W arning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a re. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certied cables ...

  • SUPER MICRO Computer SYSF617R2RT - page 30

    2-19 Chapter 2: W arning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'util ...

  • SUPER MICRO Computer SYSF617R2RT - page 31

    2-20 S UPER S ERVER "servername" User's Manual Notes ...

  • SUPER MICRO Computer SYSF617R2RT - page 32

    3-1 Chapter 3: Chassis Components Chapter 3 Chassis Components 3-1 Overview This chapter describes the most common components included with your chassis. Some components listed may not be included or compatible with your particular chassis model. For more information, see the installation instructions detailed later in this manual. 3-2 Components C ...

  • SUPER MICRO Computer SYSF617R2RT - page 33

    SCF418 Chassis Manual 3-2 Air Shroud The SCF418 chassis requires air shrouds for each node to direct the airow where cooling is needed. The air shroud will dif fer for different motherboards. If using a motherboard which is not the default in the chassis, refer to the optional parts in the Appendix of this manual, or the Supermicro web site at w ...

  • SUPER MICRO Computer SYSF617R2RT - page 34

    4-1 Chapter 4: System Interface Chapter 4 System Interface 4-1 Overview There are several LEDs on the control panel and on the drive carriers to keep you constantly informed of the overall status of the system. SCF418 models with rear I/O (left image below) include four control panels on the handles of the chassis which control each of the nodes. S ...

  • SUPER MICRO Computer SYSF617R2RT - page 35

    SCF418 Chassis Manual 4-2 4-2 Control Panel Buttons • Power: The main power button on each of the four control panels is used to apply or remove power from the power supply to each of the four systems in the chassis. T urning off system power with this but - ton removes the main power , but keeps standby power supplied to the system. Therefore ...

  • SUPER MICRO Computer SYSF617R2RT - page 36

    4-3 Chapter 4: System Interface • NIC: Indicates network activity on either LAN1 or LAN2 when ashing. 4-4 Drive Carrier LEDs The SCF418 chassis uses SAS/SA T A drives. SAS/SA T A Drives Each SAS/SA T A drive carrier has two LEDs. • Blue: Each Serial A T A drive carrier has a blue LED. When illuminated, this blue LED (on the front of th ...

  • SUPER MICRO Computer SYSF617R2RT - page 37

    SCF418 Chassis Manual 4-4 Notes ...

  • SUPER MICRO Computer SYSF617R2RT - page 38

    5-1 Chapter 5: Chassis Setup and Maintenance Chapter 5 Chassis Setup and Maintenance 5-1 Overview This chapter covers the steps required to install components and perform mainte - nance on the chassis. The only tool you will need to install components and perform maintenance is a Phillips head screwdriver . Read the safety warnings and installation ...

  • SUPER MICRO Computer SYSF617R2RT - page 39

    SCF418 Chassis Manual 5-2 5-3 Node Locations The SCF418 chassis contains eight individual motherboards in separate nodes. The nodes are available in a variety of congurations with 2.5" hard drives, 3.5" hard drives or both. See the following page for your specic SCF418 model to determine the hard drive conguration in your chassis ...

  • SUPER MICRO Computer SYSF617R2RT - page 40

    5-3 Chapter 5: Chassis Setup and Maintenance 5-4 Removing Nodes from the Chassis Each of the eight individual nodes may be removed from the chassis. Note that when a node is removed from the chassis, the hard drives located in the node will shut-down. Removing a Node 1. Power down the system and remove the power cords from the rear of the node as d ...

  • SUPER MICRO Computer SYSF617R2RT - page 41

    SCF418 Chassis Manual 5-4 Figure 5-3: Front and Rear of the Node (Y our node may differ from the one shown in this illustration) Figure 5-4 SCF418BC-R1K62BP Node 5-6 Node Congurations Overview of the Node SCF418BC-R1K62BP Front of Node Rear of Node Six 2.5" hot-swappable hard drives One Micro LP expansion card One low-prole expansion car ...

  • SUPER MICRO Computer SYSF617R2RT - page 42

    5-5 Chapter 5: Chassis Setup and Maintenance Figure 5-5: SCF418IFL-R1K62BP Node Figure 5-6: SCF418IL-R1K62BP Node SCF418IF-R1K62BP Front of Node Rear of Node T wo low-prole expansion cards T wo xed 3.5" hard drives SCF418IL-R1K62BP Front of Node Rear of Node One low-prole expansion card T wo xed 3.5" hard drives 10 SCF418IF-R1 ...

  • SUPER MICRO Computer SYSF617R2RT - page 43

    SCF418 Chassis Manual 5-6 Figure 5-7: Hard Drives and the Corresponding Motherboards Node 4 Node: 8 Node 3 Node: 7 Node 6 Node 5 Node 2 Node 1 5-7 Nodes and Associated Hard Drives The SCF418 chassis contains eight individual motherboards in separate 1U nodes. Each node controls the hard drives contained within that node. Note that if a node is pull ...

  • SUPER MICRO Computer SYSF617R2RT - page 44

    5-7 Chapter 5: Chassis Setup and Maintenance SCF418IL-R1K62BP Node 4 Controls two xed 3.5" HDDs D1-D2 Node 8 Controls two xed 3.5" HDDs H1-H2 Node 3 Controls two xed 3.5" HDDs C1-C2 Node 7 Controls two xed 3.5" HDDs G1-G2 Node 2 Controls two xed 3.5" HDDs B1-B2 Node 6 Controls two xed 3.5" HDDs, F1-F2 ...

  • SUPER MICRO Computer SYSF617R2RT - page 45

    SCF418 Chassis Manual 5-8 Removing 2.5" Hard Drive Carriers from the Node 1. Press the release button on the drive carrier . This extends the drive bay handle. 2. Use the handle to pull the drive carrier out of the chassis. Figure 5-8: Removing a 2.5" Hard Drive Carrier (Y our node may differ slightly from the one shown in this illustrati ...

  • SUPER MICRO Computer SYSF617R2RT - page 46

    5-9 Chapter 5: Chassis Setup and Maintenance The 2.5" hard drives are mounted in the drive carrier to simplify their installation and removal from the chassis. These carriers also help promote proper airow for the drive bays. Figure 5-9: 2.5" Hard Drive Carrier Installing a 2.5" Drive into the Hard Drive Carrier 1. Remove the two ...

  • SUPER MICRO Computer SYSF617R2RT - page 47

    SCF418 Chassis Manual 5-10 3. Install a new drive into the carrier with the printed circuit board side facing down so that the mounting holes align with those in the carrier . 4. Secure the hard drive by tightening all four screws. 5. Use the open handle to replace the drive carrier into the chassis. Make sure to close the drive carrier handle. 2.5 ...

  • SUPER MICRO Computer SYSF617R2RT - page 48

    5-1 1 Chapter 5: Chassis Setup and Maintenance Figure 5-13: Installing a 3.5" Hard Drive in the Drive Carrier Figure 5-12: Removing a 3.5" Fixed Hard Drive from the Node Installing and Removing 3.5" Fixed Hard Drives Removing 3.5" Fixed Hard Drives from the Node 1. Power down the system and remove the power cords from the rear o ...

  • SUPER MICRO Computer SYSF617R2RT - page 49

    SCF418 Chassis Manual 5-12 Figure 5-14: Installing a 3.5" Fixed Hard Drive in the Node 6. Install a replacement drive into the hard drive tray and secure it to the tray with the screws previously set aside. 7. Secure the hard drive tray to the oor of the node with the screw previously set aside. 8. Replace the node cover , return the node t ...

  • SUPER MICRO Computer SYSF617R2RT - page 50

    5-13 Chapter 5: Chassis Setup and Maintenance Figure 5-15: Removing the Screws at the T op of the Backplane (Y our node may differ slightly from the one shown in this illustration) 5-9 Removing and Installing the Backplane The SCF418 chassis backplane is located behind the hard drives and in front of the front system fans in each node. Although bac ...

  • SUPER MICRO Computer SYSF617R2RT - page 51

    SCF418 Chassis Manual 5-14 3. Remove the four screws securing the backplane to the node. 4. Lift the backplane up and out of the node. 1 5 Figure 5-16: Removing the Backplane from the Node (Y our node may differ slightly from the one shown in this illustration) ...

  • SUPER MICRO Computer SYSF617R2RT - page 52

    5-15 Chapter 5: Chassis Setup and Maintenance 1 2 1 3 Figure 5-17: Installing the Backplane (Y our node may differ slightly from the one shown in this illustration) Installing the Backplane Installing the Backplane into the Chassis 1. Ensure that all of the hard drive carriers have been removed from the bays in the front of the node (See 5-8 Instal ...

  • SUPER MICRO Computer SYSF617R2RT - page 53

    SCF418 Chassis Manual 5-16 5-10 Installing the Motherboard Compatible Motherboards For the most up-to-date information on compatible motherboards and other parts, visit the Supermicro Web site at www .supermicro.com. Permanent and Optional Standoffs Standoffs prevent short circuits by creating space between the motherboard and the oor of the nod ...

  • SUPER MICRO Computer SYSF617R2RT - page 54

    5-17 Chapter 5: Chassis Setup and Maintenance Installing the Motherboard 1. Review the documentation that came with your motherboard. Become familiar with component placement, requirements, cautions, and cable connections. 2. Remove the node from the chassis as described in Section 5-2, remove the node from the chassis as described in Section 5-4 a ...

  • SUPER MICRO Computer SYSF617R2RT - page 55

    SCF418 Chassis Manual 5-18 SCF418BC-R1K62BP Front of Node Rear of Node Eight 2.5" hot-swappable hard drives One Micro LP expansion card One low-prole expansion card SCF418IL-R1K62BP Front of Node Rear of Node One low-prole expansion card T wo xed 3.5" hard drives SCF418IF-R1K62BP Front of Node Rear of Node T wo low-prole expan ...

  • SUPER MICRO Computer SYSF617R2RT - page 56

    5-19 Chapter 5: Chassis Setup and Maintenance 0.15 PCIE Slot Clip PCIE Slot Shield Figure 5-19: I/O Shield Conguration Installing Rear Low-prole Expansion Cards The following instructions are for chassis nodes in which the expansion cards are mounted in the rear of the node. ...

  • SUPER MICRO Computer SYSF617R2RT - page 57

    SCF418 Chassis Manual 5-20 Figure 5-20: Assembling the PCIE Slot Bracket and Cards Assembling the PCIE Slot Bracket Assembly Each node supports one expansion card. This expansion card must be plugged into a riser card, which in turn plugs into the motherboard. Assembling the PCIE Slot Bracket Assembly 1. Remove the node from the chassis as describe ...

  • SUPER MICRO Computer SYSF617R2RT - page 58

    5-21 Chapter 5: Chassis Setup and Maintenance Riser Card Bracket Mounting Screw Bracket Mounting Screws PCIE Slot Bracket Expansion Card Installing the PCIE Slot Bracket Assembly Into the Node Installing the PCIE Slot Bracket Assembly 1. Remove the PCIE slot cover and assemble the PCIE slot bracket assembly as described on the previous page. 2. Sim ...

  • SUPER MICRO Computer SYSF617R2RT - page 59

    SCF418 Chassis Manual 5-22 Figure 5-22: Installing the Micro LP Card (Y our node may differ slightly from the one shown in this illustration) Installing the Micro LP Assembly Into the Node Installing the Micro LP Card Assembly 1. Remove the screw securing the slot cover to the chassis and set the screw aside for later use. 2. Simultaneously place t ...

  • SUPER MICRO Computer SYSF617R2RT - page 60

    5-23 Chapter 5: Chassis Setup and Maintenance PCIE Slot Clip PCIE Slot Shield Figure 5-23: PCIE Slot Conguration (Y our chassis and nodes may differ from those shown in this illustration) Installing Front Low-prole Expansion Cards The following instructions are for chassis nodes in which the expansion cards are mounted in the front of the nod ...

  • SUPER MICRO Computer SYSF617R2RT - page 61

    SCF418 Chassis Manual 5-24 Figure 5-24: Assembling the PCIE Slot Bracket and Riser Card Assembling the PCIE Slot Bracket Assembly Each node supports one expansion card. This expansion card must be plugged into a riser card, which in turn plugs into the motherboard. Assembling the PCIE Slot Bracket Assembly 1. Remove the node from the chassis as des ...

  • SUPER MICRO Computer SYSF617R2RT - page 62

    5-25 Chapter 5: Chassis Setup and Maintenance Figure 5-25: Installing the Riser Card and Bracket (Y our node may differ slightly from the one shown in this illustration) Figure 5-26: Installing the Expansion Card (Y our node may differ slightly from the one shown in this illustration) Bracket Mounting Screws 6. Insert the riser card into the approp ...

  • SUPER MICRO Computer SYSF617R2RT - page 63

    SCF418 Chassis Manual 5-26 Figure 5-27: Installing the Air Shroud (Y our node may differ from those shown in this illustration) 5-12 Installing Air Shrouds Air Shrouds Air shrouds concentrate airow to maximize fan efciency . The SCF418 and SCF418L chassis require an air shroud in each node. Installing an Air Shroud 1. Power down the system an ...

  • SUPER MICRO Computer SYSF617R2RT - page 64

    5-27 Chapter 5: Chassis Setup and Maintenance 5-13 Removing and Installing System Fans Removing and Installing Internal System Fans Removing Internal System Fans 1. Power down the system and remove the power cords from the rear of the power supplies as described in Section 5-2. Remove the node from the chassis as described in Section 5-4 and remove ...

  • SUPER MICRO Computer SYSF617R2RT - page 65

    SCF418 Chassis Manual 5-28 Removing and Installing External System Fans Figure 5-30: Installing the External Fan (Y our node may differ slightly from the one shown in this illustration) Removing a Rear Exhaust Fan 1. Determine which node contains the failed fan and power down the node with the operating system. 2. Remove the power cord from the rea ...

  • SUPER MICRO Computer SYSF617R2RT - page 66

    5-29 Chapter 5: Chassis Setup and Maintenance The SCF418 chassis includes redundant 1620W power supplies. These power sup - plies are auto-switching capable. This enables the power supplies to automatically sense and operate at a 100v to 240v input voltage. An amber light will be illuminated on the power supply when the power is off. An illuminated ...

  • SUPER MICRO Computer SYSF617R2RT - page 67

    SCF418 Chassis Manual 5-30 Notes ...

  • SUPER MICRO Computer SYSF617R2RT - page 68

    6-1 Chapter 6: Rack Installation Chapter 6 Rack Installation 6-1 Overview This chapter provides a quick setup to install the SCF418 chassis into a rack. Fol - lowing these steps in the order given should enable you to have the system installed within a minimal amount of time. 6-2 Unpacking the System Y ou should inspect the box which the chassis wa ...

  • SUPER MICRO Computer SYSF617R2RT - page 69

    SCF418 Chassis Manual 6-2 6-4 W arnings and Precautions Rack Precautions • Ensure that the leveling jacks on the bottom of the rack are fully extended to the oor with the full weight of the rack resting on them. • In single rack installations, stabilizers should be attached to the rack. • In multiple rack installations, the racks ...

  • SUPER MICRO Computer SYSF617R2RT - page 70

    6-3 Chapter 6: Rack Installation Rack Mounting Considerations Ambient Operating T emperature If installed in a closed or multi-unit rack assembly , the ambient operating tempera - ture of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environme ...

  • SUPER MICRO Computer SYSF617R2RT - page 71

    SCF418 Chassis Manual 6-4 6-5 Rack Mounting Instructions This section provides information on installing the chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean that the assembly procedure will differ slightly from the instructions provided. Y ou should also refer to the installation ins ...

  • SUPER MICRO Computer SYSF617R2RT - page 72

    6-5 Chapter 6: Rack Installation Figure 6-3: Attaching the Rails to a Rack Note: gures are for illustrative purposes only . Always install servers into racks from the bottom up. Installing the Rails on a Rack Installing the Rails 1. Adjust the length of both rails as described on the previous page. 2. Hang the hooks of the front of the outer rai ...

  • SUPER MICRO Computer SYSF617R2RT - page 73

    SCF418 Chassis Manual 6-6 Figure 6-4: Installing into a Rack Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the oor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over . Note: gures are for illustrative purposes only . Always install server ...

  • SUPER MICRO Computer SYSF617R2RT - page 74

    A-1 Appendix A: Power Supply Specications Appendix A SCF418 Power Supply Specications This appendix lists power supply specications for your chassis system. SCF418BC-R1K620BP 1620W MFR Part # PWS-1K62P-1R AC V oltage 100 - 240V , 50 - 60Hz, 7.5 Amp max +5V 18 Amp +5V standby 3 Amp +12V 49 Amp -12V 0.5 Amp +3.3V 15 Amp ...

  • SUPER MICRO Computer SYSF617R2RT - page 75

    SCF418 Chassis Manual A-2 Notes ...

  • SUPER MICRO Computer SYSF617R2RT - page 76

    B-1 Appendix C: BPN-SAS-F418B6 Backplane Specications Appendix B BPN-SAS-F418-B6 Backplane Specications T o avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components. B-1 ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com ponen ...

  • SUPER MICRO Computer SYSF617R2RT - page 77

    B-2 SCF418 Chassis Manual B-3 An Important Note to Users All images and layouts shown in this user's guide are based upon the latest PCB revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this manual. B-4 Introduction to the BPN-SAS-F418-B6 Backplane The BPN-SA ...

  • SUPER MICRO Computer SYSF617R2RT - page 78

    B-3 Appendix B: BPN-SAS-F418-B2R B-5 Front Connectors Figure B-1: Front Connectors 1. Main Power Connector (4-Pin): JP10 2. Main Power Connector (4-pin): JP13 3. Sideband Connector #1 (SB#1): JP52 4. Sideband Connector #2 (SB#2): JP54 5. Upgrade Connector: JP46 6. A TMEL Chip 7 7 7 7 7 7 1 2 4 3 1 2 4 3 1 2 5 6 1 2 7 8 1 2 7 8 44 34 12 22 23 33 + + ...

  • SUPER MICRO Computer SYSF617R2RT - page 79

    B-4 SCF418 Chassis Manual 5 Upgrade Connector The upgrade connector , designated JP46 is a rmware upgrade port. Backplane Main Power 4-Pin Connector Pin# Denition 1 and 2 Ground 3 +5V 4 +12V B-6 Front Connector and Pin Denitions 1 - 2 Backplane Main Power Connectors The 4-pin connectors, designated JP10 and JP13 provide power to the backpl ...

  • SUPER MICRO Computer SYSF617R2RT - page 80

    B-5 Appendix B: BPN-SAS-F418-B2R 1 3 12 13 24 25 36 37 48 A C A C A C A C A C A C A C A C A C A C A C A C 22 21 33 27 8 7 9 22 21 33 27 8 7 9 22 21 33 27 8 7 22 21 33 27 8 7 9 22 21 33 27 8 7 9 22 33 27 8 7 9 D13 D6 D5 D37 D29 D23 D107 D40 D24 D22 D12 D102 J35 J21 J2 J15 J13 J1 FAIL5 ACT5 FAIL4 ACT4 FAIL3 ACT3 FAIL2 ACT2 FAIL1 ACT1 SAS #5 SAS #4 SA ...

  • SUPER MICRO Computer SYSF617R2RT - page 81

    B-6 SCF418 Chassis Manual Notes ...

  • SUPER MICRO Computer SYSF617R2RT - page 82

    C-1 Appendix C: BPN-SAS-F418-B2R Backplane Specications Appendix C BPN-SAS-F418B2R Backplane Specications T o avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components. C-1 ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com pon ...

  • SUPER MICRO Computer SYSF617R2RT - page 83

    C-2 SCF418 Chassi Manual C-3 An Important Note to Users All images and layouts shown in this user's guide are based upon the latest PCB Revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this manual. C-4 Introduction to the BPN-SAS-F418-B2R Backplane The BPN-SA ...

  • SUPER MICRO Computer SYSF617R2RT - page 84

    C-3 Appendix C: BPN-SAS-F418B2R Backplane Specications + + 1 2 3 4 7 7 DESIGNED IN USA 5V 12V #0 #1 REV 1.01 BPN-SAS-F418-B2R MH2 MH1 C45 JP10 J6 J5 c-5 Front Connectors Figure C-1: Front Connectors 1. Main Power Connector (4-pin): JP10 2. SAS Port #0: J5 3. SAS Port #1: J6 1 3 2 ...

  • SUPER MICRO Computer SYSF617R2RT - page 85

    C-4 SCF418 Chassis Manual Backplane Main Power 4-Pin Connector Pin# Denition 1 and 2 Ground 3 +5V 4 +12V C-6 Front Connector and Pin Denitions 1 Backplane Main Power Connector The 4-pin connector , designated JP10 pro - vides power to the backplane. See the table on the right for pin denitions. 2 - 3 SA T A Connectors The SA T A connectors ...

  • SUPER MICRO Computer SYSF617R2RT - page 86

    C-5 Appendix C: BPN-SAS-F418B2R Backplane Specications BAR C ODE 22 21 33 27 8 7 9 22 21 33 27 8 7 9 A C A C J1 J2 D12 D13 ACT#0 ACT#1 SAS#1 SAS#0 C-7 Rear Connectors and LED Indicators Rear SAS/SA T A Connectors and LED Indicators Ports SAS/SA T A Drive Number Rear Connectors Activity LED Indicator SAS#0 SAS/SA T A HDD #0 J1 D12 SAS#1 SAS/SA T ...

  • SUPER MICRO Computer SYSF617R2RT - page 87

    C-6 SCF418 Chassis Manual Disclaimer (cont.) The products sold by Supermicro are not intended for and will not be used in life sup- port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to per- form be reasonably expected to result ...

Produzent SUPER MICRO Computer Kategorie Computer Hardware

Dokumente, die wir vom Produzenten des Geräts SUPER MICRO Computer SYSF617R2RT erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen SUPER MICRO Computer
- Bedienungsanleitungen SYSF617R2RT
- Produktkarten SUPER MICRO Computer
- Informationsbroschüren
- oder Energieetiketten SUPER MICRO Computer SYSF617R2RT
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung SUPER MICRO Computer SYSF617R2RT.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen SUPER MICRO Computer SYSF617R2RT, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen SUPER MICRO Computer SYSF617R2RT. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts SUPER MICRO Computer SYSF617R2RT ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts SUPER MICRO Computer SYSF617R2RT, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von SUPER MICRO Computer SYSF617R2RT hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von SUPER MICRO Computer SYSF617R2RT verständlich ist.

Eine gänzliche Bedienungsanleitung von SUPER MICRO Computer sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von SUPER MICRO Computer SYSF617R2RT bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von SUPER MICRO Computer SYSF617R2RT befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich SUPER MICRO Computer SYSF617R2RT, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts SUPER MICRO Computer SYSF617R2RT - die uns die ersten Schritte während der Nutzung von SUPER MICRO Computer SYSF617R2RT erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit SUPER MICRO Computer SYSF617R2RT hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von SUPER MICRO Computer SYSF617R2RT im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich SUPER MICRO Computer SYSF617R2RT?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit SUPER MICRO Computer SYSF617R2RT nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit SUPER MICRO Computer SYSF617R2RT hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)