Bedienungsanleitung JAMO APS-620N

12 Seiten 0.24 mb
Download

Zur Seite of 12

Summary
  • JAMO APS-620N - page 1

    128-8613a 1 of 12 Page 1 Model APS-620N Inst allation Manual This Remote St art System is designed to be used with Automatic T ransmission- Fuel Injection V ehicles Only! COMPONENTS: Control Module 2 Four Button RF T ransmitters Antenna/Receiver 1 1” X 1.75” Foam Pad 6 Pin Main Power Harness 7 Pin Accessory Harness 1 Hood Pin Switch 2 Pin Door ...

  • JAMO APS-620N - page 2

    128-8613a 2 of 12 Page 2 INST ALLA TION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness. Be certain that the chosen location ...

  • JAMO APS-620N - page 3

    128-8613a 3 of 12 Page 3 the remote start unit. If the vehicle is being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This switch must be installed in all applications. Failure to do so may result in personal injury or property damage. Mount the switch in the hood locations away from wat ...

  • JAMO APS-620N - page 4

    128-8613a 4 of 12 Page 4 YELLOW W ire: S tarter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from st arting while in gear . Understanding the difference between a me- chanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installation ...

  • JAMO APS-620N - page 5

    128-8613a 5 of 12 Page 5 3 Wire Ground Switched Door Lock Circuits: In this application, the Red wire of the 2 pin harness provides a ground pulse during the arming sequence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay . The Green wire of t ...

  • JAMO APS-620N - page 6

    128-8613a 6 of 12 Page 6 Wiring The 4 Pin Auxiliary Output Harness, Connector “A” The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote S tart unit's operation. Understanding these outputs and the time in which they occur will allow you to determine if t ...

  • JAMO APS-620N - page 7

    128-8613a 7 of 12 Page 7 2 Pin V alet/Program/Override Push-Button Switch, Connector “D” The Black & Grey twin lead wires loaded in the two pin blue connector are the ground supply and program/valet/override input of the Remote S tart unit. Route the two wires from the previously installed Push-Button switch to the mating connector on the c ...

  • JAMO APS-620N - page 8

    128-8613a 8 of 12 Page 8 3 Pin Antenna/Receiver , Connector “F” Route the 3 pin connector from the previously installed antenna receiver assemble to the mating connector on the control module. This connector supplies 5 volts, ground and RF data from the antenna receiver to the remote start module. Be certain this connector is firmly seated maki ...

  • JAMO APS-620N - page 9

    128-8613a 9 of 12 Page 9 T o test this circuit, while the vehicle is running under control of the remote start unit, open the vehicle’s hood. The remote start unit should shut down immediately . If not, check the wiring to the control module and the under hood pin switch. DO NOT RELEASE THE VEHICLE TO THE CONSUMER IF THIS CIRCUIT DOES NOT PERFORM ...

  • JAMO APS-620N - page 10

    128-8613a 10 of 12 Page 10 The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: B. Additional Ignition Output: C. GM V A TS Key Override: Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm ...

  • JAMO APS-620N - page 11

    128-8613a 11 of 12 Page 11 Setting Up The System Programming Features: Bank 1 Transmitter Channels S tart with the system disarmed, turn the ignition switch to the on position then: 1) Press and release the push button valet/program switch 3 times. Siren Chirps once and or Lights flash one time indicating the transmitter program mode successfully e ...

  • JAMO APS-620N - page 12

    128-8613a 12 of 12 Page 12 4 PIN IN VEHICLE DA T A BUS PORT (DBI Port) The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder inter ...

Produzent JAMO Kategorie Remote Starter

Dokumente, die wir vom Produzenten des Geräts JAMO APS-620N erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen JAMO
- Bedienungsanleitungen APS-620N
- Produktkarten JAMO
- Informationsbroschüren
- oder Energieetiketten JAMO APS-620N
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung JAMO APS-620N.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen JAMO APS-620N, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen JAMO APS-620N. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts JAMO APS-620N ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts JAMO APS-620N, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von JAMO APS-620N hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von JAMO APS-620N verständlich ist.

Eine gänzliche Bedienungsanleitung von JAMO sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von JAMO APS-620N bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von JAMO APS-620N befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich JAMO APS-620N, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts JAMO APS-620N - die uns die ersten Schritte während der Nutzung von JAMO APS-620N erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit JAMO APS-620N hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von JAMO APS-620N im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich JAMO APS-620N?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit JAMO APS-620N nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit JAMO APS-620N hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)