Bedienungsanleitung Audiovox APS 686T

20 Seiten 0.65 mb
Download

Zur Seite of 20

Summary
  • Audiovox APS 686T - page 1

    128-7201 1 of 20 Model APS 686T Installation Manual 4 Channel Remote Start / Keyless Entry System Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel With T rue T ach Reference And Automatic Transmissions Only . Kit Contents Control Module (2) - 4 Button ...

  • Audiovox APS 686T - page 2

    128-7201 2 of 20 This Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #11). If the diesel engine has a ...

  • Audiovox APS 686T - page 3

    128-7201 3 of 20 Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the under- side. Secure the switch using the nut, star washer , and on/of f face plate. It is suggested that the switch be oriented to allow the on position to be up toward the driver and the off position to be down or away from ...

  • Audiovox APS 686T - page 4

    128-7201 4 of 20 NOTE: This wire must be connected to the vehicle side of the starter cut relay (if present). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , (if present) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition swi ...

  • Audiovox APS 686T - page 5

    128-7201 5 of 20 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. BLACK w/WHITE Tracer Wire: Control Switc ...

  • Audiovox APS 686T - page 6

    128-7201 6 of 20 BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signal is received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the brake light circuit, connect the Brown w/ Black trace ...

  • Audiovox APS 686T - page 7

    128-7201 7 of 20 GREEN/YELLOW Wire: Diesel W ait T o St art For Diesel glow plug preheat circuits, this wait to start input will allow the ignition to keep the glow plugs active for the vehicles automatic time out period before cranking the starter motor . If this wire is connected to the glow plug wire, this will take precedence over the timing se ...

  • Audiovox APS 686T - page 8

    128-7201 8 of 20 4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the relay . Connect the other side of the (#1) wire to terminal #30. 5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown). NOTE: The above information and following diagram is for the GM ...

  • Audiovox APS 686T - page 9

    128-7201 9 of 20 3 W ire Ground Switched 2 S tep Door Locks In this application, the red wire provides a ground pulse during locking, or the pulsed ground lock output. Connect the red wire to the wire that provides a low current ground signal from the factory door lock switch to the factory door lock control relay . The green wire provides the firs ...

  • Audiovox APS 686T - page 10

    128-7201 10 of 20 3 Wire Positive Switched 2 S tep Door Locks The green wire provides a positive pulse during locking, or the pulsed + 12 volt lock output. Connect the green wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock control relay . The red wire provides a positive pulse d ...

  • Audiovox APS 686T - page 11

    128-7201 11 of 20 3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the unlocking sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay . The Green wire ...

  • Audiovox APS 686T - page 12

    128-7201 12 of 20 Black w/ Y ellow T race Wire: Ground Output During S t art (Crank) The Black w/ Y ellow T race wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb T est wire found in some GM vehicles. This wire is also referred to as the ECM w ...

  • Audiovox APS 686T - page 13

    128-7201 13 of 20 3 Pin Input/Output Harness: Dark Blue/Black T race Wire: External T rigger Input The Dark Blue/Black trace wire allows the remote start unit to be activated from an external source. The intent of this wire is to allow the unit to be controlled from a "POSSE/CAR-LINK" paging system or similar device. When this wire receiv ...

  • Audiovox APS 686T - page 14

    128-7201 14 of 20 NOTE: When selecting Diesel mode, be certain that the intended vehicle has a true tach reference and be certain to connect the tach input wire. To program these selectable features: 1. Turn the ignition key to the ON position. 2. Press and release the pushbutton switch 3 times 3. Immediately turn the ignition key OFF, then back to ...

  • Audiovox APS 686T - page 15

    128-7201 15 of 20 TIMED ST ART PROGRAM: The Remote S tart unit has the ability to start the vehicle automatically at timed intervals. This feature is useful in extremely cold climates where starting the engine is the only means to keep the battery charged and fluids warm. The operator has the option to have the unit st art every 2 or 4 hours for a ...

  • Audiovox APS 686T - page 16

    128-7201 16 of 20 1. With the driver's window in the down position, start the vehicle using the RF transmitter . 2. Reach inside the car and pull the hood release. 3. Raise the hood and confirm that the remote start unit shuts down. If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote St ...

  • Audiovox APS 686T - page 17

    128-7201 17 of 20 CAUTION! REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARIL Y DISCONNECTED IN STEP 3 DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE NEUTRAL SAFETY ST ART FEA TURE. MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they d ...

  • Audiovox APS 686T - page 18

    128-7201 18 of 20 KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral S tart Switch from start ...

  • Audiovox APS 686T - page 19

    128-7201 19 of 20 19 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignit ...

  • Audiovox APS 686T - page 20

    128-7201 20 of 20 © 2004 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-7201 ...

Produzent Audiovox Kategorie Automobile Electronics

Dokumente, die wir vom Produzenten des Geräts Audiovox APS 686T erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Audiovox
- Bedienungsanleitungen APS 686T
- Produktkarten Audiovox
- Informationsbroschüren
- oder Energieetiketten Audiovox APS 686T
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Audiovox APS 686T.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Audiovox APS 686T, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Audiovox APS 686T. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Audiovox APS 686T ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Audiovox APS 686T, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Audiovox APS 686T hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Audiovox APS 686T verständlich ist.

Eine gänzliche Bedienungsanleitung von Audiovox sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Audiovox APS 686T bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Audiovox APS 686T befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Audiovox APS 686T, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Audiovox APS 686T - die uns die ersten Schritte während der Nutzung von Audiovox APS 686T erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Audiovox APS 686T hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Audiovox APS 686T im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Audiovox APS 686T?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Audiovox APS 686T nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Audiovox APS 686T hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (1)

Jeff

How do you change the record speed from SP to SLP without original remote ? Thanks