-
ICP DAS USA 100-700 PLCS - page 1
DN-3000 AN INTELLIGENT MULTIPLE-FUNCTION COMMUNICATIONS INTERFACE UNIT FOR DEVICENET U ser Manual ICP PANEL-TEC Post Office Box 2394 Huntsville, Alabama 35804 (205) 534-8132 ...
-
ICP DAS USA 100-700 PLCS - page 2
...
-
ICP DAS USA 100-700 PLCS - page 3
Warranty & Notices i WARRANTY ICP PANEL-TEC, INC . warrants that all equipment purchased hereunder is warranted on a “RETURN TO FACTORY” basis against all defects in workmanship and materials under norm al and proper use and service in its unmodified condition for a period of one (1) year f rom the date of initial shipment. ICP PANEL-TEC, I ...
-
ICP DAS USA 100-700 PLCS - page 4
Table of Contents ii Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Software Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
ICP DAS USA 100-700 PLCS - page 5
Table of Contents iii Application Notes – PLCs and Devices Allen Bradley PLCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 GE Fanuc PLCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Idec PLCs . . . . . . . . . . . . . . . . . . . . . . . ...
-
ICP DAS USA 100-700 PLCS - page 6
...
-
ICP DAS USA 100-700 PLCS - page 7
Introduction 1 I NTRODUCTION The DN-3000 is an intelligent, multiple-function DeviceNet Data Transfer Unit designed for use within the harsh industrial environment. Using the DN-3000 Configuration Editor Software program, the DN-3000 can be programm ed to run either of the two (2) following application types: 1) D EVICE N ET TO PLC S OR D EVICES Al ...
-
ICP DAS USA 100-700 PLCS - page 8
Software Installation 2 G ENERAL I NFORMATION The Panel-Tec DN3000 Configuration Editor Software Program is designed to operate on an IBM or compatible computer running MS-DOS 3.3 or higher. While the Configuration Editor Software Program will run under “WINDOWS 3.1” in most configurations, it is not recommended. As of this date, no problem s h ...
-
ICP DAS USA 100-700 PLCS - page 9
Software Information 3 S OFTWARE S TART -U P To start the DN-3000 Configuration Editor program. First start your com puter and at the MS-DOS prompt; C:> type in “CDDN3000” (to change the directory) then press the ENTER key. At the next MS-DOS prompt; C:DN3000>, type in “DN3000” and press the ENTER key to start the Configuration Edit ...
-
ICP DAS USA 100-700 PLCS - page 10
Creating Project Files 4 C REATING A P ROJECT F ILE To create a project file, move the highlighted bar to the “PROJECT” heading and press the computer’s ENTER key. When the menu appears m ove the highlight bar to the “ NEW” sub-heading and press “PROJECT” Menu the computer’s ENTER key. At the “Project Name” entry area, type in y ...
-
ICP DAS USA 100-700 PLCS - page 11
Creating Project Files 5 “PROJECT TYPE” List P ROJECT T YPES DeviceNet to PLCs or Devices allows a DeviceNet Host to read and write registers in up to 32 PLCs or devices. DeviceNet to Motor Drives allows a DeviceNet Host to control and/or monitor up to 32 supported Motor Drives. ...
-
ICP DAS USA 100-700 PLCS - page 12
Creating Project Files 6 When the system returns to the “PROJECT’ m enu, notice the additional sub-headings that were added to the “PROJECT” menu and are now available for you to use. A brief description of each of these new sub-headings are listed below: Additional PROJECT Menu Sub-Headings CLOSE allows you to close a project file. More th ...
-
ICP DAS USA 100-700 PLCS - page 13
DeviceNet to PLCs or Devices 7 D EVICE N ET TO PLC S OR D EVICES The ”DeviceNet to Motor Drives” application allows a DeviceNet Host device to access data registers in up to 32 serial PLCs or Devices via Explicit Messages and/or I/O Data. Explicit Messages allows the DeviceNet Host to issue requests to the DN-3000 to read or write specific PLC/ ...
-
ICP DAS USA 100-700 PLCS - page 14
DeviceNet to PLCs or Devices 8 E XAMPLE A PPLICATIONS DeviceNet Host to Serial PLC with Pass-Through Connection DeviceNet Host to Multi-Dropped Serial PLCs NOTE: Multiple PLCs/Devices can be connected to Port 2 of a DN-3000 if: Supported PLC or Device Programming Software (if supported) 2 3 DN-3000 DeviceNet Host PLC # 1 RS-422/485 Multi-Drop Netwo ...
-
ICP DAS USA 100-700 PLCS - page 15
DeviceNet to PLCs or Devices 9 Multiple DN-3000s with Different PLC or Device Types RS-422/485 Multiple-Drop Networks DeviceNet Host PLC # 3 Brand I PLC # 1 Brand M PLC # 2 Brand I PLC # 1 Brand I PLC # 2 Brand O PLC # 1 Brand O PLC # 1 Brand S DN-3000 # 5 DN-3000 # 4 DN-3000 # 3 PLC # 2 Brand A DN-3000 # 2 PLC # 1 Brand A DN-3000 # 1 2 3 2 3 2 3 2 ...
-
ICP DAS USA 100-700 PLCS - page 16
DeviceNet to PLCs or Devices 10 C ONFIGURING P ORT #1, (D EVICE N ET ) With the highlight bar around the “PROJECT” header use the RIGHT arrow key and m ove the highlight bar to the “EDIT” header This action will close the “PROJECT” menu and open the “EDIT” menu. PLCs or Devices DeviceNet to EDIT Menu Move the highlight bar to the ? ...
-
ICP DAS USA 100-700 PLCS - page 17
DeviceNet to PLCs or Devices 11 MAC ID of DN3000 The MAC ID of the DN-3000 is its node address on a DeviceNet Network. The MAC ID of a DN-3000 can range from 0 to 63. Type the desired value in the field and press ENTER . Baud Rate Baud Rate determines the rate at which the DN-3000 exchanges data on a DeviceNet network. The Baud Rate setting must be ...
-
ICP DAS USA 100-700 PLCS - page 18
DeviceNet to PLCs or Devices 12 C ONFIGURING P ORT #2 (PLC S O R D EVICES ) When the highlight bar is around the “Port 2 (PLCs/Devices)” sub-heading, press the ENTER key. This opens a window which allows you to select the type of PLCs or devices connected to this port and check all of the communication settings. PORT # 2 PLC Configuration Windo ...
-
ICP DAS USA 100-700 PLCS - page 19
DeviceNet to PLCs or Devices 13 Use your computer’s UP/DOWN arrow keys to move through the PLC/Device Protocol List. Place the highlight bar on the desired Protocol and press the ENTER key. The software will enter this selection and automatically close the Protocol selection window . After the selection window closes, you will need to check the c ...
-
ICP DAS USA 100-700 PLCS - page 20
DeviceNet to PLCs or Devices 14 C ONFIGURING P ORT # 3 (P ASSTHROUGH ) Not all PLC/Device protocols allow for the pass-through communications. If your selected Protocol on Port 2 is capable of pass-through communications, the “Port 3 (Passthrough)” header within the “EDIT” menu will be black (if light gray, the PLC does not support Pass-Thr ...
-
ICP DAS USA 100-700 PLCS - page 21
DeviceNet to PLCs or Devices 15 I/O D ATA C ONFIGURATION Using the DOWN arrow key, move the highlight bar to the “I/O Data Configuration” sub-heading within the “ EDIT” menu and press the ENTER key. This action opens the I/O Data Configuration setup screen to allow you to set up the I/O data parameters for your project. You should have some ...
-
ICP DAS USA 100-700 PLCS - page 22
DeviceNet to PLCs or Devices 16 The DN-3000 supports up to a total of 64 bytes (32 words) of combined Input and Output data. Each word (2 bytes) of Input or Output data can be configur ed to exchange data with any one valid data register in any one of the PLCs/Devices connected to port 2 of the DN-3000 (see “CONFIGURING PORT 2” for PLC/Device P ...
-
ICP DAS USA 100-700 PLCS - page 23
DeviceNet to PLCs or Devices 17 Input Data Size This determines the number of words of Input data that will be used in your project. Input data is data that is input to your DeviceNet Host from the DN-3000 (comm and results, diagnostics information, and register data read from PLCs/Devices). This is also known as the Produced I/O Data of the DN-300 ...
-
ICP DAS USA 100-700 PLCS - page 24
DeviceNet to PLCs or Devices 18 O UTPUT D ATA T ABLE Within the “I/O Data Configuration” screen, use the DOWN arrow key to move the focus to the Output Data button and press the ENTER key. This action opens the Output Data Table setup screen to allow you to set up the PLC/Device registers to be mapped to each word of Output data. Output data is ...
-
ICP DAS USA 100-700 PLCS - page 25
DeviceNet to PLCs or Devices 19 Use Output Word xx If you want to map this word of Output data to a PLC/ Device register, select this option. If this option is not selected, any data appearing in this Output word will be ignored. PLC/Device Address This is the Address of the PLC/Device mapped to th is word of Output data. The PLC/Device Address mus ...
-
ICP DAS USA 100-700 PLCS - page 26
DeviceNet to PLCs or Devices 20 I NPUT D ATA T ABLE Within the “I/O Data Configuration” screen, use the DOWN arrow key to move the focus to the Input Data button and press the ENTER key. This action opens the Input Data Table setup screen to allow you to set up the PLC/Device registers to be mapped to each word of Input data. Input data is data ...
-
ICP DAS USA 100-700 PLCS - page 27
DeviceNet to PLCs or Devices 21 Use Input Word xx If you want to map this word of Input data to a PLC/ Device register, select this option. If this option is not selected, the data in this Input word will be set to 0. PLC/DeviceAddress This is the Address of the PLC/Device mapped to this word of Input data. The PLC/Device Address must be in the ran ...
-
ICP DAS USA 100-700 PLCS - page 28
DeviceNet to PLCs or Devices 22 C OMMAND B LOCK Using I/O data to update and/or monitor motor drive param eters requires very little programm ing in your DeviceNet Host device – the configuration of th e DN-3000 specifies which PLC/Device registers are mapped to which words of I/O data. However, you can only access a total of 32 registers this wa ...
-
ICP DAS USA 100-700 PLCS - page 29
DeviceNet to Motor Drives 23 D EVICE N ET TO M OTOR D RIVES The ”DeviceNet to Motor Drives” application allows a DeviceNet Host device to access parameters in up to 32 serial Motor Drives via Explicit Messages and/or I/O Data. Explicit Messages allows the DeviceNet Host to issu e requests to the DN-3000 to read or write specific Motor Drive par ...
-
ICP DAS USA 100-700 PLCS - page 30
DeviceNet to Motor Drives 24 E XAMPLE A PPLICATIONS DeviceNet Host to Serial Motor Drive Supported Motor Drive DN-3000 DeviceNet Host 2 3 DeviceNet Host to Multi-Dropped Serial Motor Drives NOTE: Multiple Motor Drives can be connected to Port 2 of a DN-3000 if: Drive #1 RS-422/485 Multi-Drop Network DeviceNet Host 2 3 Drive # 2 DN-3000 Drive # 3 Up ...
-
ICP DAS USA 100-700 PLCS - page 31
DeviceNet to Motor Drives 25 Multiple DN-3000s with Different Motor Drive Types RS-422/485 Multiple-Drop Networks DeviceNet Host Drive # 3 Brand I Drive # 1 Brand M Drive # 2 Brand I Drive # 1 Brand I Drive # 2 Brand O Drive # 1 Brand O Drive # 1 Brand S DN-3000 # 5 DN-3000 # 4 DN-3000 # 3 Drive # 2 Brand A DN-3000 # 2 Drive # 1 Brand A DN-3000 # 1 ...
-
ICP DAS USA 100-700 PLCS - page 32
DeviceNet to Motor Drives 26 C ONFIGURING P ORT #1, (D EVICENET ) With the highlight bar around the “PROJECT” header use the RIGHT arrow key and m ove the highlight bar to the “EDIT” header This action will close the “PROJECT” menu and open the “EDIT” menu. DeviceNet to Motor Drives EDIT Menu Move the highlight bar to the “Port 1 ...
-
ICP DAS USA 100-700 PLCS - page 33
DeviceNet to Motor Drives 27 MAC ID of DN3000 The MAC ID of the DN-3000 is its node address on a DeviceNet Network. The MAC ID of a DN-3000 can range from 0 to 63. Type the desired value in the field and press ENTER . Baud Rate Baud Rate determines the rate at which the DN-3000 exchanges data on a DeviceNet network. The Baud Rate setting must be th ...
-
ICP DAS USA 100-700 PLCS - page 34
DeviceNet to Motor Drives 28 C ONFIGURING P ORT # 2 (M OTOR D RIVES ) Using the DOWN arrow key, move the highlight bar to the “Port 2 (Motor Drives)” sub-heading (within the “ EDIT” menu) and press the ENTER key. This action opens the Motor Drive selection screen to allow you to select the drive manufacturer and to check all the motor drive ...
-
ICP DAS USA 100-700 PLCS - page 35
DeviceNet to Motor Drives 29 2-Wire RS422 or RS485 Communications This box will only need to be checked if the communications with your Motor Drive is a 2-wire RS485 or RS422 interface. When 2-wire comm unications are be ing used, RTS must be looped back to CTS on the DN-3000 side of the cable. This can be done on the RS232 side by looping pins 4 a ...
-
ICP DAS USA 100-700 PLCS - page 36
DeviceNet to Motor Drives 30 I/O D ATA C ONFIGURATION Using the DOWN arrow key, move the highlight bar to the “I/O Data Configuration” sub-heading within the “ EDIT” menu and press the ENTER key. This action opens the I/O Data Configuration setup screen to allow you to set up the I/O data parameters for your project. You should have some id ...
-
ICP DAS USA 100-700 PLCS - page 37
DeviceNet to Motor Drives 31 The DN-3000 supports up to a total of 64 bytes (32 words) of combined Input and Output data. Each word (2 bytes) of Input or Output data can be confi gured to exchange data with any one valid parameter in any one of the motor drives connected to port 2 of the DN-3000 (see “CONFIGURING PORT 2” for motor drive type an ...
-
ICP DAS USA 100-700 PLCS - page 38
DeviceNet to Motor Drives 32 Input Data Size This determines the number of words of Input data that will be used in your project. Input data is data that is input to your DeviceNet Host from the DN-3000 (comm and results, diagnostics information, and parameter data read from m otor drives). This is also known as the Produced I/O Data of the DN-3000 ...
-
ICP DAS USA 100-700 PLCS - page 39
DeviceNet to Motor Drives 33 O UTPUT D ATA T ABLE Within the “I/O Data Configuration” screen, use the DOWN arrow key to move the focus to the Output Data button and press the ENTER key. This action opens the Output Data Table setup screen to allow you to set up the motor drive parameters to be m apped to each word of Output data. Output data is ...
-
ICP DAS USA 100-700 PLCS - page 40
DeviceNet to Motor Drives 34 Use Output Word xx If you want to map this word of Output data to a motor drive param eter, select this option. If this option is not selected, any data appearing in this Output word will be ignored. Motor Drive Address This is the Address of the Motor Drive mapped to th is word of Output data. The Motor Drive Address m ...
-
ICP DAS USA 100-700 PLCS - page 41
DeviceNet to Motor Drives 35 I NPUT D ATA T ABLE Within the “I/O Data Configuration” screen, use the DOWN arrow key to move the focus to the Input Data button and press the ENTER key. This action opens the Input Data Table setup screen to allow you to set up the motor drive parameters to be m apped to each word of Input data. Input data is data ...
-
ICP DAS USA 100-700 PLCS - page 42
DeviceNet to Motor Drives 36 Use Input Word xx If you want to map this word of Input data to a motor drive param eter, select this option. If this option is not selected, the data in this Input word will be set to 0. Motor Drive Address This is the Address of the Motor Drive mapped to th is word of Input data. The Motor Drive Address must be in the ...
-
ICP DAS USA 100-700 PLCS - page 43
DeviceNet to Motor Drives 37 C OMMAND B LOCK Using I/O data to update and/or monitor motor drive param eters requires very little programm ing in your DeviceNet Host device – the configuration of the DN-3000 specifies which motor drive parameters are mapped to which words of I/O data. However, you can only access a total of 32 motor drive param e ...
-
ICP DAS USA 100-700 PLCS - page 44
DeviceNet to Motor Drives 38 U PPER L INK C ONFIGURATION (Mitsubishi Drives Only) The “Upper Link Configuration” screen is only used with Mitsubishi Drives. To open this screen, place the highlighted bar around the “Upper Link Table” sub-heading (within the “EDIT” menu) and press the ENTER key. The Upper Link Table is used to select whi ...
-
ICP DAS USA 100-700 PLCS - page 45
DeviceNet to Motor Drives 39 E XCEPTION T ABLE (Mitsubishi Drives Only) There are some parameters within Mitsubishi Drives that m ust be written to the drive as 2-byte ASCII numbers instead of the usual 4-byte ASCII numbers. These param eter numbers need to be entered for each drive that requires these “exceptions” to the usual 4-byte ASCII for ...
-
ICP DAS USA 100-700 PLCS - page 46
Transferring Project Files 40 T RANSFERRING P ROJECT F ILES From the “TRANSFER” menu you will be able to: 1) Transfer (Download) a completed project file to the DN-3000 2) Upload a project file from the DN-3000 3) Compare a loaded project file within the DN-3000 to a stored project file within the computer. 4) Check the current application with ...
-
ICP DAS USA 100-700 PLCS - page 47
Transferring Project Files 41 Communication “Startup” Screen T RANSFER O PTIONS Download Project to DN3000 Allows you to transfer (download) any creat ed project file from the PC to the DN-3000. Upload Project from DN3000 Allows you to transfer (upload) the project file stored in the DN-3000 to the PC. The computer will upload the project file ...
-
ICP DAS USA 100-700 PLCS - page 48
Options Settings 42 O PTIONS S ETTINGS Use the LEFT/RIGHT arrow keys to highlight the top “OPTIONS” heading and press the ENTER key. This will open the OPTIONS” menu. From within the “OPTIONS” m enu you can change the directory where project files are stored, select the PC communications port to use, and set up your printer. Any changes y ...
-
ICP DAS USA 100-700 PLCS - page 49
Options Settings 43 NOTE: Each time you start the “DN-3000 Configuration Software Program” it defaults (unless you saved the directory information to disk - see “Save Options to Disk” ) to the “Projects” sub-directory allowing you to open only those files saved within this sub-directory. To access project files saved in a different dire ...
-
ICP DAS USA 100-700 PLCS - page 50
Options Settings 44 S ET C OM P ORT To change the communications port (default setting = COM 1) setting, m ove the highlight bar to the “Set Com Port” sub-heading and press the ENTER key. When the “Set Communications Port” screen appears, use the LEFT/RIGHT arrow keys to highlight the communications port desired and then press the SPACE BAR ...
-
ICP DAS USA 100-700 PLCS - page 51
Options Settings 45 S ET P RINTER O PTIONS To change the printer port (default = LPT 1) setting, move the highlight bar to the “Setup Printer” sub- heading and press the ENTER key. When the “Setup Printer” screen appears (see following page), use the arrow keys to highlight the “LPTx” or “FILE” setting as required and press the SPAC ...
-
ICP DAS USA 100-700 PLCS - page 52
Technical Information 46 P OWER R EQUIREMENTS 9 - 28 VDC , 7 WATT with optional Earth Ground. A 9 VDC power supply (Part # 4000-0203) is available from Panel-Tec. P HYSICAL D IMENSIONS 3.64” 5.54” 5.6” 6.75” 7.485 8.30” .62 ” 1.9” .95” .95” ...
-
ICP DAS USA 100-700 PLCS - page 53
Technical Information 47 D IP S WITCH S ETTINGS OPERATING MODE Switch # 1 Switch # 2 Switch # 3 Switch # 4 Normal Off Off Off Off Configuration Off Off ON Off Diagnostic ON ON Off Off V ISUAL (LED) I NDICATORS The DN3000 has 5 tri-color LEDs: 2 Communication Port LEDs (Ports 2 and 3), a Status LED and 2 DeviceNet LEDs (Module Status and Network Sta ...
-
ICP DAS USA 100-700 PLCS - page 54
Technical Information 48 C ONFIGURATION M ODE : LED COLOR MEANING Communication Port # 3 LED Flashing Red-Green Communicating with Com puter Status LED Flashing Green Configuration Mode D IAGNOSTIC M ODE : LED COLOR MEANING Flashing Green Port is Operational Communication Port LEDs Flashing Red or Yellow Port not Operational or Loopback Connector n ...
-
ICP DAS USA 100-700 PLCS - page 55
Application Notes – PLCs and Devices 49 A LLEN -B RADLEY PLC 5, SLC500 AND M ICRO L OGIX PLC S Registers Accessed The DN-3000 will only access registers in Integer files in the PLC memory (N file types). W hen specifying register numbers in the DN-3000 Configurati on Software, the file number is entered into the File Number field and the elem ent ...
-
ICP DAS USA 100-700 PLCS - page 56
Application Notes – PLCs and Devices 50 I DEC M ICRO -3 PLC S Registers Accessed The DN-3000 will only access registers in the Data Register Area of PLC memory (D0 to D9999). W hen entering register numbers, only the offset into this area (0-9999) should be entered. For example, to access register number D1, the value 1 should be entered. To acce ...
-
ICP DAS USA 100-700 PLCS - page 57
Application Notes – PLCs and Devices 51 K OYO / PLC D IRECT 205 S ERIES PLC S Registers Accessed The DN-3000 can access all register types in the 205 Series PLC through the use of the V-Memory assignments shown in the following table: V-Memory Address PLC Registers Accessed V00000 – V00177 Timer T0 – T177 Current Values V01000 – V01177 Coun ...
-
ICP DAS USA 100-700 PLCS - page 58
Application Notes – PLCs and Devices 52 Important Note : The V-Memory word numbers in the above table are shown in octal. These num bers must be converted to decimal before they are entered into the DN-3000 Configuration Software. For example, if the DN-3000 is to access register V02000, the value 2000 in octal corresponds to the value 1024 in de ...
-
ICP DAS USA 100-700 PLCS - page 59
Application Notes – PLCs and Devices 53 M ITSUBISHI FX S ERIES PLC S Registers Accessed The DN-3000 will only access registers in the Data Register Area of PLC memory (D0 to D9999). W hen entering register numbers, only the offset into this area (0-9999) should be entered. For example, to access register number D1, the value 1 should be entered. ...
-
ICP DAS USA 100-700 PLCS - page 60
Application Notes – PLCs and Devices 54 S IEMENS S7-200 PLC S Registers Accessed The DN-3000 will only access registers in the V-Memory area of PLC mem ory (VB0 to VB9999) which are 8-bit registers. Because the DN-3000 will only read and write 16-bit values, it will use two consecutive 8-bit registers in Siemens S7 PLCs to form a 16-bit value. Th ...
-
ICP DAS USA 100-700 PLCS - page 61
Application Notes – PLCs and Devices 55 S QUARE D M ODEL 100-700 PLC S Registers Accessed The DN-3000 will only access registers in the Data Area of PLC memory (S0 to S9999). W hen entering register numbers, only the offset into this area (0-9999) should be entered. For example, to access register number S10, the value 10 should be entered. To ac ...
-
ICP DAS USA 100-700 PLCS - page 62
Application Notes – PLCs and Devices 56 T OSHIBA EX AND M S ERIES PLC S Registers Accessed The DN-3000 will only access registers in the Data Register of PLC memory (D0 to D9999). W hen entering register numbers, only the offset into this area (0-9999) should be entered. For example, to access register number D0, the value 0 should be entered. To ...
-
ICP DAS USA 100-700 PLCS - page 63
Application Notes – Motor Drives 57 B ALDOR M OTOR D RIVES Drive Parameter Numbers Assigned By Panel-Tec ASCII COMMAND COMMAND DESCRIPTION READ OR WRITE PARAMETER NUMBERS P Parameter Comm and Read/Write 1000-6999 from Baldor Manual IO IO Status (J1 or J4) Read Only 7001 for Terminal Pin 1 Status IO IO Status (J1 or J4) Read Only 7002 for Terminal ...
-
ICP DAS USA 100-700 PLCS - page 64
Application Notes – Motor Drives 58 Drive Addresses Assigned By Panel-Tec Drive Number 255 is used to address all motor drives present on a 485 or 422 com munications link. This drive address can only be used when writing a parameter or value to the motor drives. This allows for motor drives to be multi-dropped together and a com mand such as a n ...
-
ICP DAS USA 100-700 PLCS - page 65
Application Notes – Motor Drives M ITSUBISHI M OTOR D RIVES Drive Specific Completion Codes (Bits 6 thru 4 of Result Word) 2 = Drive Returned a Mode Error 3 = Drive Returned an Instruction Code Error 4 = Drive Returned a Data Range Error 5 = Drive Returned a Communications Error or DN-3000 encountered a Com munications Error. 6 = Drive Returned a ...
-
ICP DAS USA 100-700 PLCS - page 66
Cable Diagrams 60 DN3000 Configuration Cable (or Pass-Through Port Cable) Computer DN3000 DB9 Female DB25 Male PART # 7000-RS232 TXD 03 ------------------------------ 03 RXD RXD 02 ------------------------------ 02 TXD CABLE TYPE GND 05 ------------------------------ 07 GND 4 Conductor Round RTS 07 CTS 08 DCD 01 DTR 04 DSR 06 Computer DN3000 DB25 F ...
-
ICP DAS USA 100-700 PLCS - page 67
Cable Diagrams 61 Allen Bradley PLC5 DN3000 PLC MODEL DB25 Male DB25 Male PLC5 Channel 0 RXD 03 ------------------------------ 02 TXD TXD 02 ------------------------------ 03 RXD PART # 7000-6004 G N D 0 7 ------------------------------ 07 GND R T S 0 4 CABLE TYPE C T S 0 5 3 or 4 Conductor Round SLC500 DN3000 PLC MODEL - SLC5/03 & 04 DB9 Femal ...
-
ICP DAS USA 100-700 PLCS - page 68
Cable Diagrams 62 GE Fanuc 90/20, 30, 70 GE Fanuc DN3000 PLC MODEL DB15 Male DB25 Male 90/20,30,70 RDB 11 ------------------------------ 23 TX+ PART # 7000-6016 SDB 13 ------------------------------ 24 RX+ R D A 1 0 ------------------------------ 21 TX- CABLE TYPE ------------------------------ 22 RX- SDA 12 4 Conductor Round 06 1 5 08 1 4 ...
-
ICP DAS USA 100-700 PLCS - page 69
Cable Diagrams 63 IDEC MICRO-3 DN3000 Solder End 8 7 6 5 4 3 2 1 PLC MODEL - Micro-3 Mini Din DB25 Male D+ 01 ------------------------------ 23 TX+ PART # 7000-6022 2 4 R X + D - 02 --- --------------------------- 21 TX- CABLE TYPE 2 2 R X - 3 Conductor Round 04 RTS 05 CTS PLC MODEL FA Series DN3000 FA with Link Adapter DB25 Male DB25 Male PART # 7 ...
-
ICP DAS USA 100-700 PLCS - page 70
Cable Diagrams 64 Koyo/PLC Direct View From Back Side ← Clip 6 5 4 3 2 1 KOYO 205 DN3000 RJ11 DB25 Male PART # 7000-6031 TXD 04 ------------------------------ 03 RXD CABLE TYPE RXD 03 ------------------------------ 02 TXD Round Phone Cable GND 01 ------------------------------ 07 GND View From Back Side 4 3 2 1 ← Cli p KOYO 305 DN3000 R J 0 4 D ...
-
ICP DAS USA 100-700 PLCS - page 71
Cable Diagrams 65 Mitsubishi FX Series MITSUBISHI DN3000 PLC MODEL - FX DB25 Male DB25 Male RX+ 02 ------------------------------ 23 TX+ TX+ 03 ------------------------------ 24 RX+ PART # 7000-6061 CTS+ 04 ------------------------------ 18 RTS+ RX- 15 ------------------------------ 21 TX- TX- 16 ------------------------------ 22 RX- CABLE TYPE 17 ...
-
ICP DAS USA 100-700 PLCS - page 72
Cable Diagrams 66 Modicon View from Back ← Cli p 8 7 6 5 4 3 2 1 MODICON DN3000 PLC MODEL RJ-45 DB25 Male Micro 984 C T S 0 2 ------------ Orange ------ 04 RTS PART # 7000-6037 TXD 03 ------------ Black --------- 03 RXD RXD 04 ------------ Red ----------- 02 TXD CABLE TYPE G N D 0 5 ------------ Green -------- 07 GND Flat Phone Cable 0 6 -------- ...
-
ICP DAS USA 100-700 PLCS - page 73
Cable Diagrams 67 Omron HOST LINK DN3000 PLC MODEL DB25 Male DB25 Male 232 Host Link TXD 02 ------------------------------ 03 RXD PART # 7000-6043 RXD 03 ------------------------------ 02 TXD CABLE TYPE GND 07 ------------------------------ 07 GND 4 Conductor Round R T S 0 4 CTS 05 CQM1 DN3000 PLC MODEL DB9 Male DB25 Male CQM1 TXD 02 -------------- ...
-
ICP DAS USA 100-700 PLCS - page 74
Cable Diagrams 68 Siemens S7 PLC/Drive DN3000 DB9 Male DB25 Male PART # 7000-6045 D+ 03 ------------------------------ 23 TX+ 24 RX+ D - 08 ------------------------------ 21 TX - CABLE TYPE 2 2 R X - 3 or 4 Conductor Round 0 4 R T S 0 5 C T S G N D 05 ------------------------------ 07 GND Note: To connect additional PLC’s, daisy-chain Pin 3 of ea ...
-
ICP DAS USA 100-700 PLCS - page 75
Cable Diagrams 69 Square D Square D DN3000 PLC MODEL DB9 Male DB25 Male Models 100-700 RX+ 04 ------------------------------ 23 TX+ PART # 7000-6052 TX+ 02 ------------------------------ 24 RX+ R X - 0 3 ------------------------------ 21 TX- CABLE TYPE 01 ------------------------ 22 RX- TX- ------ 4 Conductor Round Solder End 8 7 6 5 4 3 2 1 TSX07 ...
-
ICP DAS USA 100-700 PLCS - page 76
Cable Diagrams 70 Simatic TI5 Series TI5 232 Port DN3000 PLC MODEL DB9 Female DB25 Male TI5 232 Port TXD 03 ------------------------------ 03 RXD RXD 02 ------------------------------ 02 TXD PART # 7000-6047 GND 05 ------------------------------ 07 GND R T S 0 7 CABLE TYPE CTS 08 4 Conductor Round DCD 01 DTR 04 DSR 06 TI5 422 Port DN3000 PLC MODEL ...
-
ICP DAS USA 100-700 PLCS - page 77
Cable Diagrams 71 Toshiba Toshiba DN3000 PLC MODEL S tripped Wires DB25 Male EX & M Series RXA ----------------------------------- 23 TX+ PART # 7000-6056 TXA ----------------------------------- 24 RX+ CABLE TYPE R X B ----------------------------------- 21 TX- 4 Conductor Round TXB ----------------------------------- 22 RX- Toshiba DN3000 PLC ...
-
ICP DAS USA 100-700 PLCS - page 78
Cable Diagrams 72 Baldor Motor Drives BALDOR DN3000 DRIVE TYPE - 485 Stripped Wires DB25 Male RXB ------------------------------ 23 TX+ PART # 7000-9002 2 4 R X + R X A ------------------------------ 21 TX- CABLE TYPE 2 2 R X - 3 or 4 Conductor Round GND ------------------------------- 07 GND 04 RTS 05 CTS DRIVE TYPE - 232 BALDOR DN3000 DB9 Female ...
-
ICP DAS USA 100-700 PLCS - page 79
Cable Diagrams 73 Mitsubishi Motor Drives Mitsubishi DN3000 S tripped Wires DB25 Male PART # 7000-9003 RDIA ----------------------------------- 23 TX+ SDIA ----------------------------------- 24 RX+ CABLE TYPE R D I B ----------------------------------- 21 TX- 4 Conductor Round SDIB ----------------------------------- 22 RX- ...
-
ICP DAS USA 100-700 PLCS - page 80
Cable Diagrams 74 Woods Motor Drives WOODS DN3000 Stripped Wires DB25 Male SIO+ ------------------------------- 23 TX+ PART # 7000-9004 2 4 R X + S I O - ------------------------------- 21 TX- CABLE TYPE 2 2 R X - 3 Conductor Round 04 RTS 05 CTS ...
-
ICP DAS USA 100-700 PLCS - page 81
Cable Diagrams 75 Yaskawa Motor Drives G5 DN3000 DRIVE MODEL S tripped Wires DB25 Male G5 Series 1 (+) ---------------------------------- 23 TX+ 2 4 R X + PART # 7000-9005 2 (-) ---------------------------------- 21 TX- 2 2 R X - CABLE TYPE 0 4 R T S 2, 3 or 4 Conductor Round 05 CTS ...
-
ICP DAS USA 100-700 PLCS - page 82
Cable Diagrams 76 DeviceNet Cable DeviceNet DN3000 S tripped Wires DB9 Male B l a c k ---------------------------------- 3 V- Blue ---------------------------------- 2 CAN_L PART # 7800-0001 Bare ---------------------------------- 5 Shield White ----------------------------- 7 CAN_H Red ----------------------------- 9 V+ CABLE TYPE 2-twisted pair ( ...
Haben Sie eine Frage bezüglich ICP DAS USA 100-700 PLCS?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit ICP DAS USA 100-700 PLCS nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit ICP DAS USA 100-700 PLCS hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.