Bedienungsanleitung Raypak 185A

18 Seiten 4.42 mb
Download

Zur Seite of 18

Summary
  • Raypak 185A - page 1

    RAYPAK REPLACEMENT INSTRUCTIONS IMPORTANT NOTICE These instructions are intended primar ily for use by qua lified personnel s pecif ical ly trained and experi enced in the insta llati on of this type of heating equipment and related system components. Installation and service pers onnel may be required to be licensed in some states. Persons not qua ...

  • Raypak 185A - page 2

    r r Fig. 1 REMOVE THESE SCREWS Fig. 2 Page 2 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 REMOVE THESE SCREWS ACCESSING THE BOARD - MODELS 206A, 207A, 266A, 267A, 336A, 337A, 406A, 407A: 1. Turn off the power to t ...

  • Raypak 185A - page 3

    REMOVING THE CIR CUIT BOARD - MODELS 185A/B, 265A/B, 33 5A/B, 405A/B: Make sure the power and gas are off. 1. Unplug all connectors from old circuit board. Fig. 7 . 2. Unplug keypad ribbon from old circuit board. 3. Remove four screws as shown in Fig. 8 . 4. Remove ol d circuit board. Fig. 7 2.2 UNPLUG ALL CONNECTOR S REMOVE KEYBOARD RIBBON Fig. 8 ...

  • Raypak 185A - page 4

    2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 Page 4 UNPLUG ALL CONNECTORS REMOVE MOUNTING S CREWS Fig. 9 Fig. 10 REMOVING THE CIRCUI T BOARD - MODELS 206A, 207A, 266A, 267A, 336A , 337A, 406A, 407A: Make sure the ...

  • Raypak 185A - page 5

    Page 5 DISCONNECTING IGNITI ON CONTROL - M ODEL S 185A, 265A, 33 5A, AND 405A ONLY : Make sure the power and gas are off. 1. Unplug all wires and connect ors from i gnition control. (See Fig. 11 .) Note: The ignition control is now part of the new control circuit b oard. Old module can be left in place but not used. Fig. 11 UNPLUG ALL WIRES 2151 Ea ...

  • Raypak 185A - page 6

    Page 6 PROPANE HEATERS ONLY: Make sure the power and gas are off. 1. Locate the pr opane tab on the board as shown in Fig. 12 . 2. Break off tab with pliers as shown in Fig. 13 & Fig. 14 . Fig. 12 Fig. 14 PROPANE BROKEN TAB 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5 ...

  • Raypak 185A - page 7

    MODELS 185, 265, 335 & 405, A & B SERIES, LOW NOX ONLY: Make sure the power and gas are off. 1. DO NOT break tab See Fig. 15 and Fig.16. 2. No additional wiring or connecti ons are necessary. 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at ...

  • Raypak 185A - page 8

    LOW NOX MODELS 207A, 267A, 337A & 407A: Make sure the power and gas are off. 1. Locate Lo Nox tab and P-10 air switch termin al on the board as shown i n Fig. 17 and Fig. 18 . 2. Break off tab shown in Fig. 19 with pliers. 3. Attach the wire from the air s witch to the P-10 locati on shown in Fig. 20 . 2151 Eastman Ave., Oxnar d, CA 93030 805-2 ...

  • Raypak 185A - page 9

    Page 9 NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZE L - M ODEL S 185, 265, 335 & 405, A & B SERIES: Make sure the power and gas are off. Note: Disregard window gasket installation i f already present. LA Y B OA RD DOWN Fig. 22 CLEAR WINDOW GASKET STICKY SIDE TO PLASTIC BEZEL RE-ASSEMBLE WITH NEW BOAR D MOUNTING SCREWS Fig. 23 ...

  • Raypak 185A - page 10

    GASKET & NEW CIRCUIT BO ARD NEW BEZEL INSTALLATION - MODELS 206A, 207A, 266A, 267A, 336A, 337A, 406A, 407A: Make sure the power and gas are off. Note: Disregard window gasket installation i f already present. 1. Remove backing on gasket and install a dhesive side on the control panel bezel as shown in Fig. 24 & Fig. 25 . 2. Re-assemble with ...

  • Raypak 185A - page 11

    Page 11 REMOVING & REPLACING SENSOR - MODELS 185, 265, 335 & 405, A & B SERIES: Make sure the power and gas are off. 1. Loosen drain plug to relieve pressure i n heat exchanger. See Fig. 27 . 2. Remove five screws and in/out access panel as shown in Fig. 28 . 3. Re-route the 2-wire s ensor connector from the board (P1) back towa rds the ...

  • Raypak 185A - page 12

    Page 12 Fig. 33 Fig. 32 CLEAR PLASTIC STRIP WITH THIN CONNECTOR Fig. 34 PLASTIC SHIELD & BRACKET INSTAL LATION - MODELS 185, 265, 335 & 405, A & B SERIES: Make sure the power and gas are off. 1. Note that the plastic shie ld is installed under the front bracket as pictured. Install the shield brackets and plastic shield using the existi ...

  • Raypak 185A - page 13

    Ensure the power and the gas has been shut off. 1. Re-connect pilot wire (side B) to new board. See Fig. 35. CONNECT THIS END TO NEW PC BOARD SPARK LUG CONNECT THIS END TO EXISTING PILOT WIRE Fig. 37 EXISTING PILOT WIRE Page 13 P/N 241169 Rev.-3 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is ...

  • Raypak 185A - page 14

    Page 14 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 15

    Page 15 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 16

    Page 16 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 17

    Page 17 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 18

    Page 18 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

Produzent Raypak Kategorie Swimming Pool Heater

Dokumente, die wir vom Produzenten des Geräts Raypak 185A erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Raypak
- Bedienungsanleitungen 185A
- Produktkarten Raypak
- Informationsbroschüren
- oder Energieetiketten Raypak 185A
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Raypak 185A.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Raypak 185A, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Raypak 185A. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Raypak 185A ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Raypak 185A, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Raypak 185A hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Raypak 185A verständlich ist.

Eine gänzliche Bedienungsanleitung von Raypak sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Raypak 185A bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Raypak 185A befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Raypak 185A, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Raypak 185A - die uns die ersten Schritte während der Nutzung von Raypak 185A erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Raypak 185A hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Raypak 185A im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Raypak 185A?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Raypak 185A nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Raypak 185A hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)