Bedienungsanleitung Uniden Clock

24 Seiten 0.2 mb
Download

Zur Seite of 24

Summary
  • Uniden Clock - page 1

    Digital Depth Sounder OPERATING GUIDE ...

  • Uniden Clock - page 2

    ...

  • Uniden Clock - page 3

    1 Features, Specifications, and availability of Optional Accessories are all subject to change without notice. Contents Unpacking ...............................2 Features ................................2 Installing the QT 206 ..........................3 Transducer Wiring ...........................4 Power Cable Wiring ..........................4 ...

  • Uniden Clock - page 4

    UNPACKING Your QT-206 Depth Sounder box should contain the following items: • Transducer with 3 lugs attached • Power Cable (attached to the gauge) • Mounting Bracket and hardware • This Operating Guide If any items are missing or damaged, please contact your dealer immediately. FEATURES n Depth Readings – The QT-206 is designed to give d ...

  • Uniden Clock - page 5

    INSTALLING THE QT-206 1. Find a location on your dash panel which will provide clear viewing and access to the LCD window. 2. After finding the right location for the indicator unit, mark a 2-inch hole to be cut out. 3. Check behind the panel for any cables or wiring which could be damaged. Then cut out the 2-inch hole. 4. Test fit the unit in the ...

  • Uniden Clock - page 6

    TRANSDUCER WIRING On the rear of the unit, locate the terminal lugs extending out of the rear of the instrument. These terminals are used to connect the transducer wires. When shipped from the factory, the transducer is wired with 3 female lugs attached. These lugs need to be inserted onto the male terminals located on the rear of the gauge. The BL ...

  • Uniden Clock - page 7

    1. Connect the main unit to a 12-volt battery using the power cable supplied with your unit. You may extend this cable as necessary, but you must observe proper polarity (i.e., RED is positive and BLACK is negative). 2. Connect the BLACK wire to the negative ( - ) battery terminal. 3. Connect the RED wire to the positive ( + ) battery terminal. 4. ...

  • Uniden Clock - page 8

    transducer directly behind any strakes, ribs, intakes and outlets for live wells and/or engine cooling water, or any protrusion which may cause turbulence or cavitation. On slower, heavier displacement boats, good results can be achieved further from the keel. DO NOT INSTALL YOUR TRANSDUCER UNDERNEATH A GASOLINE OVERFLOW. THIS WILL DESTROY THE PLAS ...

  • Uniden Clock - page 9

    3. Mark the outline of each slot on the hull. Mark the screw locations 1/8" from the bottom of each slot, and drill four holes 3/4" deep with a 9/64" drill. The slots in the bracket allow 5/8" of vertical adjustment which can be utilized to lower the transducer further into the water to achieve optimal performance. 4. Using the ...

  • Uniden Clock - page 10

    have a solvent base. However, some solvent bases will damage encapsulation materials and plastics to varying degrees. If you need anti-fouling protection, use only paints with a mineral spirits base; do not use acetone vinyl-based paints. Glochester (RULE) Durapoxy is a hard, mineral spirits-based paint that has been found to be virtually transpare ...

  • Uniden Clock - page 11

    • Do not install it on a lifting strake since this is the area where air bubbles travel from the bow to the stern, to provide a smooth ride. • On displacement power boats (trawlers), mount the transducer well aft and close to the centerline. • On I/Os, mount the transducer close to the engine(s). • On inboards, always mount the transducer w ...

  • Uniden Clock - page 12

    5. Apply a 1/8" thick layer of sealant around the lip of the plastic or bronze housing. A thin layer should also be applied up the sidewalls to a height of 1/4" greater than the hull thickness. This will ensure there is sealant material in the threads to seal them, and hold the housing nut securely in place. 6. From the outside of the hul ...

  • Uniden Clock - page 13

    Mounting the Transducer 1. Drill a 1/8" pilot hole in the preferred transducer location. Refer to the previous section to determine the best location for your type of boat. 2. Drill a hole “slightly” larger than the stem of the transducer. Be careful not to make it too large as you will run the risk of water leaking into the hull. 3. Cut t ...

  • Uniden Clock - page 14

    INSIDE-THE-HULL TRANSDUCERS This type of transducer does not require the drilling of a hole as does the Through-the-Hull Transducer. However, since the sound waves transmitted and received by the Inside-the-Hull Transducer must pass through the hull, transducer performance will be reduced. The success of Inside-the-Hull installation is greatly depe ...

  • Uniden Clock - page 15

    Use one of the following methods to determine if your chosen location is satisfactory: 1. Place the transducer in a plastic bag filled 1/2 to 3/4 full of water. Tie or tape the bag tightly around the transducer cable. Wet the selected location and place the bag against the hull, pressing the transducer face against the hull. If the hull is void fre ...

  • Uniden Clock - page 16

    UNDERSTANDING SONAR All depth sounders emit ultrasonic sound signals from the transducer into the water located under your boat. These sound signals travel through the water at a rate of approximately 4,800 feet per second (1500 meters per second). The depth sounder transmits a signal and receives a returning echo. The unit calculates the amount of ...

  • Uniden Clock - page 17

    SETTING THE SHALLOW WATER ALARM Located just below the LCD window are two keys labeled “DOWN” and “UP” Alarms. These keys are used to set the Shallow Water depth alarm so that it will audibly alert you if you enter water shallower than your preset depth alarm. To set the alarm, press the “DOWN” key. The LCD shows an alarm depth of A03. ...

  • Uniden Clock - page 18

    SHALLOW WATER SENSITIVITY The Shallow Water Sensitivity controls a circuit in the depth sounder that affects the first 10 feet of water. It alters the system’s response time in this area only, and can be used to compensate for installation imperfections. Example: • SHALLOW READINGS: If your instrument occasionally displays random, false shallow ...

  • Uniden Clock - page 19

    WHEN TO USE LESS SENSITIVITY: SHALLOW READINGS Use less sensitivity when your instrument displays a series of random, shallow readings (3.5’, 2.9’, 4.1’) and the actual depth is greater. How to Perform When looking at the rear of the instrument, this adjustment is made in a clockwise direction. (This control operates much like the volume cont ...

  • Uniden Clock - page 20

    WHEN TO USE MORE SENSITIVITY: DOUBLE ECHOES (READINGS TOO DEEP) Use more sensitivity when your instrument displays depths that are too deep; that is, greater than the actual depth. For example, if you are in 6’ of water and turn this control too far in the less sensitivity direction, you may see “12.0’” appear in the LCD window. This is ver ...

  • Uniden Clock - page 21

    TROUBLESHOOTING GUIDELINE Symptom Possible Reasons Suggested Solutions “0.0" is flashing in the display window. Unit is not receiving an echo which could be caused by a variety of reasons: Sensitivity Adjustment was turned too much in one direction, actually squelching out the echo. Transducer is defective, therefore not transmit- ting or re ...

  • Uniden Clock - page 22

    Symptom Possible Reasons Suggested Solutions Unit is not reading prop- erly at high speeds, causing high random numbers at high RPM . There are three basic types of installations: Inside-the-Hull, Through-the-Hull, and Transom Mount. Gen- erally, this situation is attributed to the location and installation of the transducer. A great deal of air is ...

  • Uniden Clock - page 23

    One Year Limited Warranty WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shal ...

  • Uniden Clock - page 24

    ©1995,1996 Uniden America Corporation All rights reserved. Printed in the United States of America OMQT206 ...

Produzent Uniden Kategorie Clock

Dokumente, die wir vom Produzenten des Geräts Uniden Clock erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Uniden
- Bedienungsanleitungen Clock
- Produktkarten Uniden
- Informationsbroschüren
- oder Energieetiketten Uniden Clock
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Uniden Clock.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Uniden Clock, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Uniden Clock. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Uniden Clock ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Uniden Clock, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Uniden Clock hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Uniden Clock verständlich ist.

Eine gänzliche Bedienungsanleitung von Uniden sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Uniden Clock bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Uniden Clock befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Uniden Clock, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Uniden Clock - die uns die ersten Schritte während der Nutzung von Uniden Clock erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Uniden Clock hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Uniden Clock im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Uniden Clock?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Uniden Clock nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Uniden Clock hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)