Deutsch dropdown-ico

Bedienungsanleitung Agilent Technologies 87075C

169 Seiten 3.19 mb
Download

Zur Seite of 169

Summary
  • Agilent Technologies 87075C - page 1

    User’ s and Service Guide Agilent T echnologies 87075C Multiport T est Set For E506x Network Analyzers Part No. 8 7075-9002 7 Printed in USA Pri n t D a te : Ma rch 20 0 4 © Copyrigh t 2004 Agilent T echnolog ies, Inc. ...

  • Agilent Technologies 87075C - page 2

    ii W ARRANTY ST A TEMENT THE MA TERIAL CONT AINED I N THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, T O THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LA W , AGI LENT DISCLAIMS ALL W ARRAN TIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMA TIO N CONT AINED HE ...

  • Agilent Technologies 87075C - page 3

    iii users will rece ive no greater than Limited Rights as defined in F AR 52.227-14 (J une 1987) or DF AR 252.227-7015 (b)(2) (November 1995 ), as applicable in any technical data. Certific atio n Agilent T echnologies , Inc. c ertifies tha t this p roduct met its published spec ifications at the time of shipment from the factor y . Agilent T ec hn ...

  • Agilent Technologies 87075C - page 4

    iv W ARNING W ar ning denotes a hazard. It calls attention to a procedure which, if not correctly perf ormed or adhered to, could result in injury or loss of life. Do not proc eed beyond a warning note until the indicated conditions are fully understood and met. CAUTION Caution denot es a hazard. It call s attention to a procedure t hat, if not c o ...

  • Agilent Technologies 87075C - page 5

    Contents Content s-v 1. Introduction a nd Installation Introduction to the Multipo rt T est Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 A Complete Multipor t T est Sys tem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Fully Characteriz e Y our Devices wit h a Single Connection. . . . . . . . . . 2 Improve Y o ur Com ...

  • Agilent Technologies 87075C - page 6

    Content s-vi Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 T est Set Ca l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 SelfCal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87075C - page 7

    Contents Content s-vii Cal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 System Me nu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 6. SCPI Command Reference 7. COM Objec t Reference 8. Specificatio ns About This Chapter . . . . . . . . ...

  • Agilent Technologies 87075C - page 8

    Content s-viii Contents P ost -Repair Pro cedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 8 P arts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 9 Order ...

  • Agilent Technologies 87075C - page 9

    1 1 Intr oducti on and Instal lation ...

  • Agilent Technologies 87075C - page 10

    2 Chapter 1 Introduc tion and In stallation Introduction to the Multipor t T est Set Introduction to the Multiport T est Set • The 87075C is a 75-ohm multiport test s et that is available with 6 or 12 test ports. A Complete Multiport T est System 87075C multiport te st sets ar e designed to work w ith E5061A (1 .5 GHz) and E5062A (3 G Hz) RF netw ...

  • Agilent Technologies 87075C - page 11

    Chapter 1 3 Introduct ion and Installatio n Introduction to the Multipor t T est Set Impr ove Y our Competitiveness wit h a Fully Specified T est S ystem A multi port test set co upled with an E50 61A/E5062A network analyzer of fers fully specified perfor mance at the actual test po rts, wheth er y ou meas ur e in a fixtur e or at the end of tes t ...

  • Agilent Technologies 87075C - page 12

    4 Chapter 1 Introduc tion and In stallation Introduction to the Multipor t T est Set Reduce the Effects of T est-Syste m Drift with SelfCal SelfCal is an internally autom ated calibration technique th at us es so lid-state switches to measure cal ibration standards located inside the test set. SelfCal executes automatically in just a few secon ds ( ...

  • Agilent Technologies 87075C - page 13

    Chapter 1 5 Introduct ion and Installatio n Introduction to the Multipor t T est Set T ypeface Conventions Sample ( bold ) Boldface type is us ed when a term is defined or emphas i s. Sample (Italic) Italic type is us ed for emphasi s. [ ] key Indicates a hardkey (key on the fr ont panel or external key board) labeled “Sample.” “key” may be ...

  • Agilent Technologies 87075C - page 14

    6 Chapter 1 Introduc tion and In stallation If Y ou are Using an 8712ET /ES or 871 4ET/ES Analyze r If Y ou ar e Using an 87 12ET/ES or 8714ET/ES Analyzer This docum ent is intended fo r use with E5061A and E5062A analyzers, so some of the information (for exam ple, key presses and calibration features) doe s not apply to your analyzer . Y ou can o ...

  • Agilent Technologies 87075C - page 15

    Chapter 1 7 Introduct ion and Installatio n Inst a llation Installation This section will guide you through the steps necessary to correctly and safely install your mult ipor t test s et. The steps are: • “Step 1. Ch eck the Shipment” • “Step 2. Determine Network Analyzer Compatibility” • “Step 3. Co nnect the T est Set to the Analy ...

  • Agilent Technologies 87075C - page 16

    8 Chapter 1 Introduc tion and In stallation Installation Figur e 1-1 87075C Multip ort T est Set — T wo V ersions 8707 5C Opt i on 006 — Six Po rt T est Set 87075C Op t ion 012 — T welve Port T est Set ...

  • Agilent Technologies 87075C - page 17

    Chapter 1 9 Introduct ion and Installatio n Inst a llation S tep 1. Check the Shipment After you hav e unpacked your test set, keep the packaging materials to use if y our instrument should n eed to be returned for maintenance or repair . NOTE The packaging material is designed to pr otect the test set from damage that can happen du ring shipping . ...

  • Agilent Technologies 87075C - page 18

    10 Chapter 1 Introduc tion and In stallation Installation T able 1-1 T est Set Accessories Supplied Item No. Des cripti on Qu an tity Part Number 1 Power Cord 1 See Figur e 4-3 . 2 T ype-N Cable (Analyzer to test set’ s REFLECTION Port) 1 1. Not to be us ed with a rack-mounted system or i f the analyzer h as had its botto m feet removed. See Figu ...

  • Agilent Technologies 87075C - page 19

    Chapter 1 11 Introduct ion and Installatio n Inst a llation Figure 1- 2 T est Set Accessories Supplied S tep 2. Determine Network Analyzer Compatibilit y If you are using a 8712ET /E S or 8714ET/ ES an alyzer , refer t o “If Y ou ar e Using an 8712ET/ES or 8 714ET/ES Analyzer” . ...

  • Agilent Technologies 87075C - page 20

    12 Chapter 1 Introduc tion and In stallation Installation S tep 3. Connect the T est Set to the Analyzer For usin g your system on a bench, configu re and connect the two i nstruments as show n in Figure 1-3 : Connect the Parallel In connector of the test set to the analyzer Parallel connector . Use the parallel cab le that was shipped with the mu ...

  • Agilent Technologies 87075C - page 21

    Chapter 1 13 Introduct ion and Installatio n Inst a llation NOTE There are special semi -rigid cables that s hould be used to connect th e analyzer’ s test ports to the test s et’s REFL ECTION and TRANSMISSION ports when used in a rack (or a b ench configuration where the analy zer ’ s bottom feet have been removed). Th ese cables were shipp ...

  • Agilent Technologies 87075C - page 22

    14 Chapter 1 Introduc tion and In stallation Installation S tep 4. Satisfy Electrical and En vironmental Requir ements NOTE Refer to you r network analyzer ’ s User ’ s Guid e for information on electrical and environmental requirem ents for your network analyzer . 1. The line power module on your multiport tes t set h a s an auto rang ing in p ...

  • Agilent Technologies 87075C - page 23

    Chapter 1 15 Introduct ion and Installatio n Inst a llation Figure 1- 4 Protect ive Earth Ground W ARNING This is a S afety Class I p roduct (provid ed with a protective ea rthing gr ound incorporated in the power cord). The mains plug shall only be inserted in a socket outlet prov id ed with a protective earth contact . Any interrup tion of the pr ...

  • Agilent Technologies 87075C - page 24

    16 Chapter 1 Introduc tion and In stallation Installation 5. Ensure there are at least two inches of clearance around the side s and back of the test set or the system cabinet. Figure 1- 5 V entilation Clearance Requirements 6. Set up a static-safe w orkstation. Electrosta t ic discharg e (ESD) can damage or destro y components. • table mat with ...

  • Agilent Technologies 87075C - page 25

    Chapter 1 17 Introduct ion and Installatio n Inst a llation S tep 5. Activate the T est Set 1. Connect the semi-r igi d cables that were shipped w ith yo ur test set as shown in Figure 1- 6 . Ch eck T abl e 1-1 to be sure that yo u a re us ing the correct cables with your sy stem configurat ion (the cables you use w ill be dif ferent dep ending o n ...

  • Agilent Technologies 87075C - page 26

    18 Chapter 1 Introduc tion and In stallation Installation S tep 6. Connect Peripheral Devices After you’v e ensu red t hat you r sys tem i s work ing pro perly , connect any periph erals that you intend to use with your system. NOTE See your analyzer’ s User ’ s Guide for information o n peripheral con n ections. ...

  • Agilent Technologies 87075C - page 27

    Chapter 1 19 Introduct ion and Installatio n Preventi ve Maint enance Preventive Maintenance Preventive maintenance consists of checking the front panel connectors . This should be done at least every six months — more often i f the test set is used d aily on a product ion lin e or in a har s h environment. V isually inspect th e front panel conn ...

  • Agilent Technologies 87075C - page 28

    20 Chapter 1 Introduc tion and In stallation Preventive Maintenance ...

  • Agilent Technologies 87075C - page 29

    21 2 Making Measur ements This chapter describes the procedure of measurement using the 87075C multi-port test se t. ...

  • Agilent Technologies 87075C - page 30

    22 Chapter 2 Making M easurem ents Measurement P roce dures Measurement Pr ocedures Measurement is performed in 4 majo r steps belo w . • Setting the port connections o f the m ult i-po rt te st set • Setting the measurement conditions • Ca librat ing th e test s et • Performing measurement Multiport test system needs to be p r oper ly inst ...

  • Agilent Technologies 87075C - page 31

    Chapter 2 23 Making M easurem ents Meas uremen t Pro cedures St e p 2 . Press [S ystem] . St e p 3 . Press 87075 Setup . St e p 4 . Press 87075 Contr ol to make the status on. St e p 5 . Press R eflection . St e p 6 . Select the port to be connected to the reflection port. St e p 7 . Press T ransmission . St e p 8 . Select the port to be connected ...

  • Agilent Technologies 87075C - page 32

    24 Chapter 2 Making M easurem ents Measurement P roce dures [Scale] - Refer e nce Position [Scale] - Refer e nce V alue St e p 5 . Other settings Set the graph title, trace colo r , and so on as necessary . [Display] - Edit T itle Label [System] - Misc Setup - Color Setup - Corr e sp ondi ng soft key ...

  • Agilent Technologies 87075C - page 33

    Chapter 2 25 Making M easurem ents Meas uremen t Pro cedures Calibrating th e test set The procedure to calibrate the test set is descr ibed below . Note that the calibration procedure descr i bed here is a typical one u s ing a mechanical calibra tion kit. For more detailed info rmation, including procedures us ing ECal, see Chapte r 3 . St e p 1 ...

  • Agilent Technologies 87075C - page 34

    26 Chapter 2 Making M easurem ents Measurement P roce dures St e p 4 . Executing calibration After the measure ment of the calibration standards for necessary ports is finished, calculate and save the calibration coefficients. [Cal] - Te s t S e t C a l - Calibration - Done NOTE The calibration data of the 87075C multi- por t test set has higher pr ...

  • Agilent Technologies 87075C - page 35

    Chapter 2 27 Making M easurem ents Meas uremen t Pro cedures Performing Measurements The procedu re to execute measur ement is described below . This section descr ibes how to trigger actual meas urement. For more information, see the E50 61A/62A User ’ s Guide. St e p 1 . Setting the trigger sour ce Select a trigger source. B ecause the trigger ...

  • Agilent Technologies 87075C - page 36

    28 Chapter 2 Making M easurem ents Measurement P roce dures ...

  • Agilent Technologies 87075C - page 37

    29 3 T est Set Cal and Se lf Cal ...

  • Agilent Technologies 87075C - page 38

    30 Chapter 3 T est Set Cal and S elfCal Introduction Introduction This chapter presents information on the fo llo wing topics: • T est Set Cal: An Overview • T est Set Cal and SelfCal: Theory of Operation Measurement calibration is a process that improve s measur ement accuracy by us ing error correctio n arrays to remove systematic meas uremen ...

  • Agilent Technologies 87075C - page 39

    Chapter 3 31 T est Set Cal and SelfCal Introduction SelfCal A SelfCal is an automated internal system calibration that should be performed on a regular , frequent bas i s. If the oper at ing temperature of the analyzer and test set is within the specified range (refer to Cha pter 8 ), the recommended time in terval is about once an hou r . A SelfCa ...

  • Agilent Technologies 87075C - page 40

    32 Chapter 3 T est Set Cal and S elfCal T est Set Cal: An Ov erview T est Set Cal: An Overview T o perform a T est Set C al the following st eps are required and are explained in detail in this section: 1. Set up measurement paramete rs, such as frequen cy range, power l evel, number of measurements points, etc. 2. Determine the best position for t ...

  • Agilent Technologies 87075C - page 41

    Chapter 3 33 T est Set Cal and SelfCal T est Set Cal: An Ov erview The analyzer will interpo l ate between calibrated measurem ent points when the frequency s p an is narrowed. However , you s hould be aware that best measur ement accuracy is compro mis ed with this interpolation. Figure 3- 1 F requency Range Example NOTE It is recomm ended t hat y ...

  • Agilent Technologies 87075C - page 42

    34 Chapter 3 T est Set Cal and S elfCal T est Set Cal: An Ov erview Other Paramete rs to Conside r The following parameters, if changed after calibrating, will not in val idate the calibration, but will cause the “C ?” notation to appear at the status bar o f the disp lay: • Sweep time • Number o f points •P o w e r l e v e l • IF bandw ...

  • Agilent Technologies 87075C - page 43

    Chapter 3 35 T est Set Cal and SelfCal T est Set Cal: An Ov erview Figu re 3-2 Th e Cali brat ion R e feren ce Pl ane ...

  • Agilent Technologies 87075C - page 44

    36 Chapter 3 T est Set Cal and S elfCal T est Set Cal: An Ov erview CAUTION Although the T est Set Cal can calibrate out the effects of your external hard ware, the drift-removing featur es of the SelfCal cannot remove drift as sociated with any external fixtures or cabling. See Figu re 3- 4 . Be sure that all external f i xtures and cables are ex ...

  • Agilent Technologies 87075C - page 45

    Chapter 3 37 T est Set Cal and SelfCal T est Set Cal: An Ov erview Determine the T est Set Ports to Be U sed T o save time, calibrate the lowest number of ports necessar y for your test setup. F or example, if you r test setup requires the use of only 6 of the available twelve ports, calibrate for 6 ports; there is no need to sp end the time to cal ...

  • Agilent Technologies 87075C - page 46

    38 Chapter 3 T est Set Cal and S elfCal T est Set Cal: An Ov erview St e p 3 . Press Te s t S e t C a l . St e p 4 . Press C alibration . NOTE If Calib ra tio n is disabled, the status of the multi- por t test set of this channel may be off. See "Procedure of setting ports for the multi-port test set" in the previous chapter . St e p 5 . ...

  • Agilent Technologies 87075C - page 47

    Chapter 3 39 T est Set Cal and SelfCal T est Set Cal: An Ov erview St e p 1 0 . Connect the s hort standard t o the Port y side an d press Port y Sho rt to measure cal ibrati on da ta. St e p 11 . Connect the load st andard to the Port y side and press Por t y Loa d to measure cal ibrati on da ta. St e p 1 2 . Connect the t hru standar d between po ...

  • Agilent Technologies 87075C - page 48

    40 Chapter 3 T est Set Cal and S elfCal T est Set Cal: An Ov erview Calibrating: Insert able Port Pairs versus Non insertabl e Port Pairs During the thro ugh portion of the calibration, if an adjacent port pair (for ex ample, 1-to-2, 3- t o-4, 5-to-6, et c.) can be connected directly witho u t using a cable or an adapter , the port pair is inser ta ...

  • Agilent Technologies 87075C - page 49

    Chapter 3 41 T est Set Cal and SelfCal T est Set Cal: An Ov erview St e p 6 . Connect the ECal mod ule between ports x and y and p r es s ECal to measure calibration data and calcu lat e the calibration coefficients. St e p 7 . Repeat S tep 5 and Step 6 for necessary port pairs . ...

  • Agilent Technologies 87075C - page 50

    42 Chapter 3 T est Set Cal and S elfCal T est Set Cal: An Ov erview NOTE A 2-port type ECal module is assumed in the above procedure . For a 4-port ECal module, in case of S-param eter test set, you can connect any two of the 4 ports when connecting the ECal module in S tep 6. In case of trans mission/reflection test s et, one of the connections li ...

  • Agilent Technologies 87075C - page 51

    Chapter 3 43 T est Set Cal and SelfCal T est Set Cal: An Ov erview St e p 2 . Press [Save/Recall] . St e p 3 . Press Recall S tate , then t he softkey corr esponding t o the regis ter from which yo u want to recall the instrument st ate. Copying the T est Set Cal. The E5061A/62 A lets you tempor arily save T est Set calibration data only for each c ...

  • Agilent Technologies 87075C - page 52

    44 Chapter 3 T est Set Cal and S elfCal T est Set Cal: An Ov erview NOTE Self Cal is set for each meas urement channel and executed for a port pair selected for the chann el. NOTE SelfCals are not automatically initiated on currently unused ports . A port is never automatically calibrated unless it is selected— even if the time interval h as been ...

  • Agilent Technologies 87075C - page 53

    Chapter 3 45 T est Set Cal and SelfCal T est Set Cal a nd SelfCal: Theory of Operation T est Set Cal and SelfCal: Theory of Operation Adding a multiport test set to the analyzer degrades raw performance of the test system as well as introdu ces drift. T est Set Cal provides t he vector error correction that allows the system to achiev e good p erfo ...

  • Agilent Technologies 87075C - page 54

    46 Chapter 3 T est Set Cal and S elfCal T est Set Cal and SelfCal: Theory of Ope ration Figur e 3-3 Internal T ransfer S tandards A SelfCal is an automa t ic measurement of the test set internal standards that allows the system to remove system drift that o ccurs du e to en viron mental changes s uch as temperature. SelfCal allo ws the multiport sy ...

  • Agilent Technologies 87075C - page 55

    Chapter 3 47 T est Set Cal and SelfCal T est Set Cal a nd SelfCal: Theory of Operation Drift can be minimized by controlling the environmental temper ature and humidity , and by using high quality connectors, semi- r ig id cables, and fixturing that reduces cable movement to a minimum. Figure 3-4 Drift Removal: T est Set Cal a nd Self Cal ...

  • Agilent Technologies 87075C - page 56

    48 Chapter 3 T est Set Cal and S elfCal T est Set Cal and SelfCal: Theory of Ope ration ...

  • Agilent Technologies 87075C - page 57

    49 4 Front/Rea r Panel ...

  • Agilent Technologies 87075C - page 58

    50 Chapter 4 Front/Rear Panel This chapt er contains informat ion on the ports and switches fo und on the front an d rear p ane l s of t he t est set . ...

  • Agilent Technologies 87075C - page 59

    Chapter 4 51 Fron t/Rea r Panel Front Panel Front Panel Figur e 4-1 Fr ont Panel Features Line Power Switch The test set line POWER switch is located at the bottom left corner of the front panel. See Figur e 4-1 . The line POWER switch turn s the power to the test set to either on or off. Item Description 1 Line Power Switch 2 Port Connection S tat ...

  • Agilent Technologies 87075C - page 60

    52 Chapter 4 Front/Rear Panel Front Panel The front panel LINE s witch disconnects the mains circuits fr om the mains suppl y after the EMC filters and before others pa r ts o f the in strument. T est Po rts The front pan el test ports are 75 ohm f emale connectors that are used to con n ect to the device u nder test. CAUTION Never connect 50 oh m ...

  • Agilent Technologies 87075C - page 61

    Chapter 4 53 Fron t/Rea r Panel Front Panel The REFLECTION Connector The REFLECTION connector is a female 75 ohm type-N connector that con n ects directly to the POR T 1 of the network analyzer us ing a semi-rigid cable that was shipped with you r test set. CAUTION Check your analy zer's docu mentation for damag e limits to th e analyzer po rt ...

  • Agilent Technologies 87075C - page 62

    54 Chapter 4 Front/Rear Panel Rear Panel Rear Panel Figur e 4-2 Rear Panel Featur es The P ARALLEL IN C onnector This female DB-25 connecto r input is always connected to the network analy zer. The analyzer pr ovides control of the test set through this cable as well as passing through an y printer control signals to the test s et’ s P ARALLEL OU ...

  • Agilent Technologies 87075C - page 63

    Chapter 4 55 Fron t/Rea r Panel Rear Panel Line Module The line module contains the power cable recep tacle. See “S tep 4. Satisfy Electrical and Envi ronmental Requirem ents” for power suppl y requirements. Power Cabl es The line po wer cable is s upplied in one of several configurations, depen ding on the destination of the ori ginal shipment ...

  • Agilent Technologies 87075C - page 64

    56 Chapter 4 Front/Rear Panel Rear Panel Figure 4- 3 Power Cable and Line (Mains) Plug Part Numbers ...

  • Agilent Technologies 87075C - page 65

    57 5K e y R e f e r e n c e ...

  • Agilent Technologies 87075C - page 66

    58 Chapter 5 Key R eferen ce This chapter contains an alphabetical reference of the networ k analyzer keys that are used exclusively f o r the multiport test set. It also contains en t ries for some of the network analyzer keys that are likely to be used w hile making measurements wi th your mult iport te st s et. For a compl ete referen ce of netw ...

  • Agilent Technologies 87075C - page 67

    Chapter 5 59 Key Ref erence Cal Menu Cal Menu [Cal] Display s the softkeys relate d to settin g and executing calibration. Correction T oggles o n /off the erro r correction. :SEN S{1- 4} :CO RR:S T A T Te s t S e t C a l Displays th e softkeys t o execute multi-po rt test set cali bration. Te s t S e t C a l Enables/di sa bles the c alibration dat ...

  • Agilent Technologies 87075C - page 68

    60 Chapter 5 Key R eferen ce Cal Menu [Cal] (Conti nued) Te s t S e t C a l Calibration Port 1- 2 ECal Executes 2-po rt ECa l for po rts 1 and 2 of the mu lti- po rt test set. :SEN S{1- 4} :CO RR:M UL T:C OLL:ECAL 2,1 Return Returns to the softkey displa y in on e leve l uppe r . Port 3- 4 Displays the softkeys to calibrate ports 3 and 4 of the m u ...

  • Agilent Technologies 87075C - page 69

    Chapter 5 61 Key Ref erence Cal Menu [Cal] (Conti nued) Te s t S e t C a l Time r Specifies the ex ecution interval of the auto c a libration feature u sing the internal standard of the multi-port te st set. Y ou can speci fy 1 or mo re in mi nute s. :SEN S{1- 4} :CO RR:M UL T:SE LF:T IM Self Cal Once Executes the auto calibra tion fe a ture us ing ...

  • Agilent Technologies 87075C - page 70

    62 Chapter 5 Key R eferen ce System M enu System Menu [System] Displays the softkey s related to co nt rol/manag ement feat ure s of the anal yzer . 87075 S etu p Displays the softkeys related to set ting the m ulti-port te s t set. 87075 C ont r ol Enables/disables the m ulti-port test se t. :SEN S{1- 4} :MU L T Reflection Displays the softk eys t ...

  • Agilent Technologies 87075C - page 71

    Chapter 5 63 Key Ref erence System Men u [System] (Continue d) 87075 S etu p Retu rn Returns to the softkey display in on e leve l uppe r . Return Returns to the softkey displa y in on e leve l uppe r . ...

  • Agilent Technologies 87075C - page 72

    64 Chapter 5 Key R eferen ce System M enu ...

  • Agilent Technologies 87075C - page 73

    65 6 SCPI Command Refer ence This chapter descr i bes the SCPI command refer ence for the Agilent E5061A /E506 2A to control th e A gil ent 870 75C Multi Po rt T est Set . I t describes th e commands using their abbreviated format in alphabetical order . ...

  • Agilent Technologies 87075C - page 74

    66 Chapter 6 SCPI Comm and Refe rence Syntax Notational conventions in th is com mand re ference This section describes the r ules to read the descr ip tion o f the commands in this chapter . Syntax Part with heading "Syntax" describes the syntax to send a command from the external controller to the E5061A/E5062A. A syntax con s ists of a ...

  • Agilent Technologies 87075C - page 75

    Chapter 6 67 SCPI C ommand Referenc e Quer y resp onse Parameters Part with heading "Parameters " describes necessary parameters when sending the command. When a parameter is a value type or a stri ng type enclosed with <>, its description, allowable setu p range, preset (factory-set) value, and s o on are given; when a parameter is ...

  • Agilent Technologies 87075C - page 76

    68 Chapter 6 SCPI Comm and Refe rence Equivalent key menu usin g th e [ ←↓ ] key and so on, and then press the [Enter] key . ...

  • Agilent Technologies 87075C - page 77

    Chapter 6 69 SCPI C ommand Referenc e :SEN S{1-4}: CORR :MUL T Multipor t T estse t C ommands This sect ion descr ibes the commands o f 87075C Multiport T estset. :SENS{ 1-4}:CORR:MU L T Syntax :SENSe{[ 1]|2|3|4}:CORRection:MU L T ip ort[:ST A T e] {ON|OFF|1|0} :SENSe{[1]| 2|3|4}:CORRe ction:MU L T iport[ :ST A T e]? Description For channel 1 to ch ...

  • Agilent Technologies 87075C - page 78

    70 Chapter 6 SCPI Comm and Refe rence :SENS{1-4} :CORR:MUL T :COLL:ECAL :SENS{1-4}:CORR:MUL T :COLL:ECAL Syntax :SENSe{[ 1]|2| 3|4}:CORRection: MUL Tiport:COLLect:ECAL <value 1>,<value 2> Descript ion For chann el 1 to channel 4, performs the calib ration of the specif ied ports using ECal. This command makes a measurement of the standa ...

  • Agilent Technologies 87075C - page 79

    Chapter 6 71 SCPI C ommand Referenc e :SENS{1 -4}:CORR:MUL T :COLL:ISOL :SENS{ 1-4}:CORR:MU L T :COLL:ISOL Syntax :SENSe{[ 1]|2|3|4}:CORRection:MUL Tiport:COLLect[:ACQuire]:ISOLation <value 1>,<value 2> Description For channel 1 t o channel 4, m easures iso lation calibration da ta for the s pecified port pair. NOTE If 2 ports yo u spec ...

  • Agilent Technologies 87075C - page 80

    72 Chapter 6 SCPI Comm and Refe rence :SENS{1-4} :CORR:MUL T :COLL:LOAD :SENS{ 1-4}:CORR:MU L T :COLL:LOAD Syntax :SENSe{[1]|2|3|4}:CORRection:MUL Tiport:COLLect[:ACQuire]:LOAD <value> Description F or channel 1 to channel 4, measures the calibration data of the load standard of the specified port. NOTE If :SENS{1-4}:M UL T on page 81 is off, ...

  • Agilent Technologies 87075C - page 81

    Chapter 6 73 SCPI C ommand Referenc e :SENS{ 1-4}:CORR:MUL T :COLL:METH :SENS{1- 4}:CORR:MUL T :COLL:METH Syntax :SENSe{[ 1]|2|3|4}:CORRection:MU L T iport:COL Lect:METHod {ER ES|SOL T2} :SENSe{[1]|2|3|4}:CORR ection:MUL T iport:COLLect: METHod? Description F or channel 1 to channel 4, selects the test set calibration from en hanced response calibr ...

  • Agilent Technologies 87075C - page 82

    74 Chapter 6 SCPI Comm and Refe rence :SENS{1-4} :CORR:M UL T :COLL:OPEN :SENS{ 1-4}:CORR:MU L T :COLL:OPEN Syntax :SENSe {[ 1]| 2| 3|4}: CORRe ction: MUL T iport:COLL ect[ :ACQuir e]:OPEN <value> Description F or channel 1 to chan nel 4, measures the calibration d ata of the open standard of the specified port. NOTE If :SENS{1-4}:M UL T on p ...

  • Agilent Technologies 87075C - page 83

    Chapter 6 75 SCPI C ommand Referenc e :SENS{ 1-4}:CORR: MUL T :COLL:SA VE :SENS{1-4}: CORR:MUL T :COLL :SA VE Syntax :SENSe {[1]|2|3|4}: CORRection: MUL T ip ort:COLL ect:SA VE Description F or channel 1 to channel 4, calculates the calibration coef ficients depending on the selected calibration type. Calib ration coefficient is calculated for all ...

  • Agilent Technologies 87075C - page 84

    76 Chapter 6 SCPI Comm and Refe rence :SENS{1-4} :CORR:M UL T :COLL:SHOR :SENS{1- 4}:CORR:MUL T :COLL:SHO R Syntax :SENSe {[1]|2|3|4}:CORR ection:MUL Tiport:COLLect[:ACQuir e]:SHORt <value > Descript ion For chan nel 1 to channel 4, measur es the calibrati on data of th e shor t stand ard of the specified port. NOTE If :SENS{1-4}:M UL T on pa ...

  • Agilent Technologies 87075C - page 85

    Chapter 6 77 SCPI C ommand Referenc e :SENS{1-4}:CORR:MU L T :COLL:THRU :SENS{ 1-4}:CORR:MU L T :COLL:THRU Syntax :SENSe{[ 1]|2|3|4}:CORR ec tion: MUL T ip ort:COLL ect[:AC Quir e ]:THR U <value 1>,<va lue 2> Description For channel 1 to chan nel 4 , meas ures th ru s tand ard calib ration d ata fo r the spec ified port pa ir . NOTE If ...

  • Agilent Technologies 87075C - page 86

    78 Chapter 6 SCPI Comm and Refe rence :SENS{1-4} :CORR:M UL T :SELF :SENS{ 1-4}:CORR:MU L T :SELF Syntax :SENSe {[1]|2|3|4}: CORRection:MUL Tiport:SELF[:ST A T e] {ON|OFF |1|0} :SENSe{[1]| 2|3|4}:CORR ection:MUL Tiport:SELF[:ST A T e]? Description For channel 1 to channel 4, specifies whether to execute the self cali bration of the test set automat ...

  • Agilent Technologies 87075C - page 87

    Chapter 6 79 SCPI C ommand Referenc e :SENS{1-4}:CORR:MUL T :SELF:ONCE :SENS{1-4}:CORR:MUL T :SELF:ONCE Syntax :SENSe {[1]|2|3|4}: CORRection: MUL T ip ort:SELF: ONCE Description For channel 1 to channel 4, executes self calibration for the port pairs that are used in the channel with the T est Set calibration. NOTE If necessary tes t set calibrati ...

  • Agilent Technologies 87075C - page 88

    80 Chapter 6 SCPI Comm and Refe rence :SENS{1-4} :CORR:M UL T :SELF:TIM :SENS{ 1-4}:CORR:MU L T :SELF:TIM Syntax :SENSe{[ 1]|2|3|4}:CORRection:MUL Tiport:SELF:TIMer <value> :SENSe{[1]| 2|3|4}:CORRe ction:MUL Tiport:SELF: TIMer? Description Fo r chan nel 1 to chan nel 4, specifies the interv al at which th e self calibration of the test set is ...

  • Agilent Technologies 87075C - page 89

    Chapter 6 81 SCPI C ommand Referenc e :SEN S{1-4}: MUL T :SEN S{1-4}:MUL T Syntax :SENSe {[ 1]| 2| 3|4}: MUL T ipo rt[:ST A T e] {ON|OFF|1|0} :SENSe{[1]| 2|3|4}:MUL Tiport[:ST A T e]? Description For channel 1 to channel 4, enables/disables the tes t set. If off is specified, test set calibration cannot b e executed. Parameters Query response {1|0} ...

  • Agilent Technologies 87075C - page 90

    82 Chapter 6 SCPI Comm and Refe rence :SENS{ 1-4}:M UL T :PO RT{1- 2}:SEL :SEN S{1-4}:M UL T :POR T{1-2 }:SEL Syntax :SENSe {[ 1]| 2| 3|4}: MUL Tiport:POR T{[1] |2}: SELe ct <val ue > :SENSe{[1]| 2|3|4}:MUL Tiport:POR T{[1]|2}: SELect? Descript ion For channel 1 to channel 4, sp ecifies port s to which the reflecti on port (port 1) of the tes ...

  • Agilent Technologies 87075C - page 91

    Chapter 6 83 SCPI C ommand Referenc e :SENS{ 1-4}:M UL T :PR OP :SEN S{1-4}:MUL T :PROP Syntax :SENSe {[1]|2|3|4}: MUL T ipo rt:PROPerty {ON|OFF|1|0} :SENSe{[1]| 2|3|4}:MUL Tiport:PROPerty ? Description For channel 1 to chann el 4, specifies whether to display the port connection status of the te st set. Parameters Query response {1|0}<newline&g ...

  • Agilent Technologies 87075C - page 92

    84 Chapter 6 SCPI Comm and Refe rence :SENS{ 1-4}:M UL T : PROP ...

  • Agilent Technologies 87075C - page 93

    85 7 COM Object Refer ence This chapt er describes the CO M object model of t he Agilent E5061A/ E5062A and the COM object reference provided for the Agil ent 87075C Multiport T est Set control in alphabetical order . ...

  • Agilent Technologies 87075C - page 94

    86 Chapter 7 COM Object Referenc e Application Objects COM Object Model The COM objects provided for the E50 61A/E5062A ar e structured hierarch ically as shown in F igure 7-1. Figur e 7-1 E5061A /E5062A COM obj ect model Applicat ion Objects The Application o bjects are at the top o f the hierarchy of the E506 1A/E5062A COM object model. They con ...

  • Agilent Technologies 87075C - page 95

    Chapter 7 87 COM Object Refe rence SCPI Objects SCPI Object s The SCPI objects are created to r ealize the SCPI commands o f the E5061 A/E5062A with the COM interface. For i nformation on the bas ic use of the SCPI objects, see “SCPI Objects” on page 87. The conversi on rules from the SCPI comm ands when writing SCPI object messages are as foll ...

  • Agilent Technologies 87075C - page 96

    88 Chapter 7 COM Object Referenc e Object T ype Notational Rules of COM Objects This section describes th e rules for the descrip tio n of the COM objects in th is chapter . Object T ype Part with h eading “Object type” des cribes the type of the E5 061A/E5062A COM object. The E 5061A/E5062A pr ovi d es p roperties and met h ods as the t ypes o ...

  • Agilent Technologies 87075C - page 97

    Chapter 7 89 COM Object Refe rence Va r i a b l e V a riable Part with heading “V ariable” describes necessary variables when using the object. It give s the d esc r ip t ion, dat a typ e, al low able ran ge, pr es et va l ue, unit , re solut ion , and notes fo r vari able ( ita lic) sh own in t he syntax. V ariables declared as the string d at ...

  • Agilent Technologies 87075C - page 98

    90 Chapter 7 COM Object Referenc e Equivalent Key Equivalent Key Part with heading “Equ ivalent key” shows the o perational procedure of the fr ont panel keys that has the s ame effect as this object. [Key] Indicates that you press the key named Key . [Key] - Item Indicates a series of k ey o peration in which y ou p ress the [Ke y ] key , move ...

  • Agilent Technologies 87075C - page 99

    Chapter 7 91 COM Object Refe rence SCPI.SENSe(C h).CORRection.MUL Tiport.COLLect.ACQuire.ISOLation SCPI Object s SCPI objects are a collection of the C OM interface having on e-on-one corresponden ce wi th the SCPI commands. This s ection describes the E5061A/E 5062A SCPI objects. SCPI.SENSe( Ch ).CORRection.MUL Tiport.COLLect.A CQuir e.ISOLat i on ...

  • Agilent Technologies 87075C - page 100

    92 Chapter 7 COM Object Referenc e SCPI.SEN Se(Ch).CORRe ction.MUL T i port.COLLect.ACQ uire.ISOLa tion Example s Dim IsPort(1) As Variant IsPort(0) = 1 IsPort(1) = 2 SCPI.SENSe(1).CORRection.MULTiport.COL Lect.ACQuire.ISOLation = IsPort Related ob jects SCPI.SENSe(C h).COR Rectio n.MUL T ipo rt.COLLe ct. ACQ uire.L OAD on page 93 SCPI.S ENSe(C h). ...

  • Agilent Technologies 87075C - page 101

    Chapter 7 93 COM Object Refe rence SCPI.SENSe(Ch).CORRection.MUL Tiport.COLLect. ACQuire.LOAD SCPI.SENSe( Ch ).CORRection.MUL Tiport.COLLect. ACQuire.LOAD Object type Property Syntax SCPI .SENSe( Ch ).CORRect ion.MUL Tiport.COLLect.ACQuire.LOAD = Va l u e Descr iption For channel 1 to channel 4, measures load calibration data for the specified port ...

  • Agilent Technologies 87075C - page 102

    94 Chapter 7 COM Object Referenc e SCPI.SENSe(Ch).CORRection.MUL Tiport.COLLect. ACQuire.OPEN SCPI.SENSe( Ch ).CORRecti on.MUL T iport.COLLect. ACQuire.OPEN Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL Tipor t .COLLect.ACQuire.OPEN = Va l u e Descr iption For channel 1 to channel 4, measures open calibration data f or the specified ...

  • Agilent Technologies 87075C - page 103

    Chapter 7 95 COM Object Refe rence SCPI.SENSe(Ch).CORRection.MUL T i port.COLLect. ACQuire.SHORt SCPI.SENSe( Ch ).CORRection.MUL Tiport.COLLect. ACQuire.SHORt Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL Tipor t .COLLect.ACQuire.SHORt = Va l u e Descr iption For channel 1 to channel 4, measures s hort calibration data for the s peci ...

  • Agilent Technologies 87075C - page 104

    96 Chapter 7 COM Object Referenc e SCPI.SENSe(Ch).CORRection.MUL T i port.COLLect. ACQuire.THRU SCPI.SENSe( Ch ).CORRecti on.MUL T iport.COLLect. ACQuire.THRU Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL Tipor t .COLLect.ACQuire.THRU = Data Descr iption For channel 1 to channe l 4, measures thru calibr ation data for the specifi ed ...

  • Agilent Technologies 87075C - page 105

    Chapter 7 97 COM Object Refe rence SCPI.SENSe(Ch).CORRection.MUL Tiport.COLLect. ECAL SCPI.SENSe( Ch ).CORRection.MUL Tiport.COLLect. ECAL Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL Tipor t .COLLect.ECAL = Data Descr iption For channel 1 to channel 4, performs the ca l ibration of the specified ports using ECAL. This command makes ...

  • Agilent Technologies 87075C - page 106

    98 Chapter 7 COM Object Referenc e SCPI.SENSe(Ch).CORRection.MUL Tiport.COLLect. METHod SCPI.SENSe( Ch ).CORRecti on.MUL T iport.COLLect. METHod Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL Tipor t .COLLect.METHod = Param Param = SCPI.SENS e( Ch ).CORRectio n.MUL Tiport.COLLect.METHod Descr iption For the active trace of channels 1 ...

  • Agilent Technologies 87075C - page 107

    Chapter 7 99 COM Object Refe rence SCPI.SENSe(Ch).CORRection.MUL Tiport.COLLect. METHod Equiva len t key [CAL] - Te s t S e t C a l - Calibration - Cal T ype ...

  • Agilent Technologies 87075C - page 108

    100 Chapter 7 COM Object Referenc e SCPI.S ENSe(C h).CO RRe ction. MUL T iport.CO LLe ct. SA VE SCPI.SENSe( Ch ).CORRecti on.MUL T iport.COLLect. SA VE Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL Tipor t .COLLect.SA VE Descr iption For the active trace of channels 1 to 4 ( Ch ), calculates the cal ibration coef ficients depending o ...

  • Agilent Technologies 87075C - page 109

    Chapter 7 101 COM Object Refe rence SCPI.SENSe(C h).CORRec tion.MUL Tiport.SELF . ONCE SCPI.SENSe( Ch ).CORRection.MUL Tiport.SELF . ONCE Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL T iport.SEL F .ONCE Descr iption For channel 1 to channel 4, executes self calibration for the port pairs that are used in the channel with the T est S ...

  • Agilent Technologies 87075C - page 110

    102 Chapter 7 COM Object Referenc e SCPI.SEN Se(C h) .CO RR e ctio n .MUL Tiport. SE LF . ST A T e SCPI.SENSe( Ch ) .CORRe cti on.MUL T ipo rt.SE LF . ST A T e Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL T iport.SEL F .ST A T e = St a tu s Status = SCPI.S ENSe( Ch ) . CORRection.MUL T iport.SELF .ST A T e Descr iption For channel 1 ...

  • Agilent Technologies 87075C - page 111

    Chapter 7 103 COM Object Refe rence SCPI.SENSe(Ch).CORRection.MUL Tiport.SELF . TIMer SCPI.SENSe( Ch ).CORRection.MUL Tiport.SELF . TIMer Object type Property Syntax SCPI .SENSe( Ch ).CORRection.MUL T iport.SEL F .TIMer = Va l u e Va l u e = SC PI.SENS e( Ch ).CORRection.MUL T iport.SELF .TIMer Descr iption For channel 1 to channel 4, specifies the ...

  • Agilent Technologies 87075C - page 112

    104 Chapter 7 COM Object Referenc e SCPI.SE N Se(Ch).MUL Tipor t.PORT(Pt).SELect SCPI.SENSe( Ch ).MUL T iport.POR T( Pt ).SEL ect Object type Property Syntax SCPI .SENSe( Ch ) .MUL Tipo rt.POR T( Pt ).SELect = Va l u e Va l u e = SC PI.SENS e( Ch ).MUL T iport.POR T( Pt ).SELect Descr iption For channel 1 to channel 4, specifies po rts to which the ...

  • Agilent Technologies 87075C - page 113

    Chapter 7 105 COM Object Refe rence SCPI.S ENSe(Ch).MUL T iport.POR T(Pt).SELec t SCPI.SEN Se(Ch ).COR Rectio n.MUL T ipo rt.COLLe ct. ACQ uire.O PEN on page 94 SCPI.SEN Se(Ch ).COR Rection.M UL T ipo rt.COLLe ct. ACQ uire.S HOR t on page 95 SCPI.SEN Se(Ch ).CORRec tion.M UL T iport .COLLe ct. ACQu ire.THRU on page 96 Equiva len t key [System] - 87 ...

  • Agilent Technologies 87075C - page 114

    106 Chapter 7 COM Object Referenc e SCPI.S ENSe( Ch).MU L Tiport.PR OPer ty SCPI.SENSe( Ch ).MUL T iport.PROPerty Object type Property Syntax SCPI .SENSe( Ch ) . MUL T iport.PROPerty = St a t u s Status = SCPI.S ENSe( Ch ) . MUL T i port.PRO Perty Descr iption For channel 1 to channel 4, specifies wh ether to display the port connection status of t ...

  • Agilent Technologies 87075C - page 115

    Chapter 7 107 COM Object Refe rence SCPI.SE NSe(Ch). MUL Tiport .ST A T e SCPI.SENSe( Ch ).MUL T iport.ST A T e Object type Property Syntax SCPI .SENSe( Ch ) .MUL T iport.ST A T e = St atus Status = SCPI.S ENSe( Ch ).MUL T ipo rt .ST A T e Descr iption For channel 1 to channel 4, enables /dis ables the test set. If off is specified, test set calibr ...

  • Agilent Technologies 87075C - page 116

    108 Chapter 7 COM Object Referenc e SCPI.SEN Se(C h).MU L Tip ort.S T A T e ...

  • Agilent Technologies 87075C - page 117

    109 8 Specifications ...

  • Agilent Technologies 87075C - page 118

    11 0 Chapter 8 Specifi catio ns About This Chapter This chapter descr i bes the perfor mance and features of the 87 075C multiport test sets. The performance of a test set is formally described in this chapter under the categories Specifications and Su pplemental Informa tion . Performance of the test set to specifications is co vered by the Agilen ...

  • Agilent Technologies 87075C - page 119

    Chapter 8 111 Specifi catio ns Definitions All specifications and char acteristics apply over a 25 ° C ± 5 ° C range (unl ess otherwise stated) and thirty minutes after the i nstrument has been turned on. Specification (spec.): W arranted perf ormance. Specifications includ e guardbands to account for the exp ect ed statistical distribution, mea ...

  • Agilent Technologies 87075C - page 120

    11 2 Chapter 8 Specifi catio ns T est Set Performance T able 8-1 T est Set Input/Output Performance, 75 Ω 87075C T est Set Input/Output Description Specificat ion Supplemental Frequency Range 87075C 3 MH z–1.3 GH z — RF Input Power Maximum In put Po wer at 0.1 dB compressio n — 16 dB m (t ypi ca l ) Inpu t Dama ge Powe r — 20 dBm (cha ra ...

  • Agilent Technologies 87075C - page 121

    Chapter 8 11 3 Specifi catio ns T able 8-2 T est Set Input/Output Perf ormance, 75 Ω (co ntinued) 87075C (7 5 Ω ) T est Set Input/Output Des crip tion Specifica tio n, dB T ypical, dB 3 MHz to 1. 3 G H z 3 MH z to 1.3 GHz Source Mat ch , test po rt 1 1. This is t he match of the test set p ort which has b een select ed as the source port. The t ...

  • Agilent Technologies 87075C - page 122

    11 4 Chapter 8 Specifi catio ns T able 8-3 T est Set General Informatio n 87075C Genera l Informati on Description Specification Supplemen tal Inform ation Port Connectors 87075C — T ype-N, F emale 75 Ω (nomina l) Fro nt Panel Ports 87075C, 75 Ω , Op t.006 6 — 87075C, 75 Ω , Op t.012 12 — Rear Panel Parallel In: Conn ector — 25-pin D- ...

  • Agilent Technologies 87075C - page 123

    Chapter 8 11 5 Specifi catio ns T able 8-3 T est Set General Information (continued) 87075C Gene ra l Infor m ation Descri ption Specif ication Supplemental Informati on Gene ra l Env ironme nta l ESD — Mini mize using s tatic-s afe work procedur es an d an ant is t atic ben ch mat (par t num b er 9300-0 797 ). Dust — Minimize f or optimum r el ...

  • Agilent Technologies 87075C - page 124

    11 6 Chapter 8 Specifi catio ns Physical Dimensions Figu re 8-1 Phy sical Dimen sio ns of th e 87 07 5C O pti on 006 Multipor t T est Set 1 1. These dimensions exclude rear protrusion s . ...

  • Agilent Technologies 87075C - page 125

    Chapter 8 11 7 Specifi catio ns Figu re 8-2 Phy si cal D imen sions of th e 8707 5C O ption 012 Multipor t T est Set 1 1. These dimens ions exclude r ear protrusions. ...

  • Agilent Technologies 87075C - page 126

    11 8 Chapter 8 Specifi catio ns Wa r r a n t y NOTE The actual wa rranty o n your i nstrument depends on the date it w as ordered as well as whether or not any warranty options were pur chased at that time. T o determine the exact warranty on your instrument, contact Agilent T echn ologies with the model and serial number of your i n strument. See ...

  • Agilent Technologies 87075C - page 127

    Chapter 8 11 9 Specifi catio ns Limitati on of W arranty The f o reg oing war rant y sha ll no t appl y to de fec ts re sulti ng fr om impr ope r or inadequa t e maintenan ce by Buyer , Buyer -supplied s oftware or i n terfacing, unauthorized modification or misuse , operati on outside of the environmental specification s for the product, or improp ...

  • Agilent Technologies 87075C - page 128

    120 Chapter 8 Specifi catio ns Contacting Agilent By inter net, phone , or fax, get assistance w ith all you r test and measurement nee d s . Online assistance: www.agilent.com/find/assist Americas Brazil (tel) (+55) 11 4197 3600 (fax) (+55 ) 11 4197 38 00 Canada (tel) 877 894 44 14 (fax) (+1) 90 5 28 2-6495 Mexi co (tel) (+52) 55 5081 9 469 (alt) ...

  • Agilent Technologies 87075C - page 129

    Chapter 8 121 Specifi catio ns Spain ( tel ) (+34) 91 631 3 300 ( alt ) (+ 34) 91 63 1 3000 ( fax ) (+34) 91 631 33 01 Swede n ( tel ) 0200 88 22 55* ( alt ) (+46) (0)8 5064 8686 ( fax ) 020 120 2 266* Switzerla nd (Fr ench) ( tel ) 08 00 80 5353 opt. 2* ( alt ) (+33) (0)1 6453 5623 ( fax ) (+41) (0)2 2 567 5313 Switz e rl an d (Ge rma n) ( tel ) 0 ...

  • Agilent Technologies 87075C - page 130

    122 Chapter 8 Specifi catio ns ...

  • Agilent Technologies 87075C - page 131

    123 9 Service ...

  • Agilent Technologies 87075C - page 132

    124 Chapter 9 Serv ice W ARNING These servicing instructions are for use by qualified personnel only . T o avoid electrical shock, do not perform any servicing unless you are qualified to do so. W ARNING The opening of covers or r emoval of parts is likely to expose danger ous voltages. Disconnect the product from all voltage sources while it is be ...

  • Agilent Technologies 87075C - page 133

    Chapter 9 125 Service Aut o m at e d Per f or ma n ce T ests Automated Performance T ests The perform ance verification tes ts make up the VBA perf ormance test soft ware program. Y our network analyzer is requ i red to execute an VB A program to verify test set performance. The perform ance verification tests are designed to v erify specifications ...

  • Agilent Technologies 87075C - page 134

    126 Chapter 9 Serv ice Automated Performan c e T e st s St e p 7 . Click "Open" butto n to down load the test program. St e p 8 . Press Select M acro to select Select Macro function. St e p 9 . Press Modul e Main to open the Modu le1 main program f i le. "87075C Perfo rmance T est Program" dialog box (Main Menu) as shown below w ...

  • Agilent Technologies 87075C - page 135

    Chapter 9 127 Service Aut o m at e d Per f or ma n ce T ests Program Overview Instru ment Info rmat ion The option and seri al number for the 87 075C can be entered. T est Condit io n The test condition, “T emperature”, “Humidity” and person doing the test ( “T ested by”) can b e entered. T est It ems The following test can be selected. ...

  • Agilent Technologies 87075C - page 136

    128 Chapter 9 Serv ice Automated Performan c e T e st s T est dialog box “T ex t” or “Graph” in the T est Result box can be s elected b efor e “Execute” button is pr essed. T o execute the tes t, click “Execute” but ton. T o retu rn the 87075C perfor mance test program d ialog box (Main Menu ), click “Back to Main Menu”. The tes ...

  • Agilent Technologies 87075C - page 137

    Chapter 9 129 Service Aut o m at e d Per f or ma n ce T ests Performance V erificati on T est Results The perform ance verification tests are designed to v erify specifications for the test set. Th is section lists the te st names alon g with som e descriptive information and the general steps involved in each test. Each test result is categorized ...

  • Agilent Technologies 87075C - page 138

    130 Chapter 9 Serv ice Automated Performan c e T e st s SRC MA TCH XX Measures reflection at p ort XX when th e p ort is switched to the test set’ s REFLECTION p ort, which is terminated with a precision load. T ests the s pecified performanc e of “Source Match,” listed in T able 8-2 in Chapter 8, “Specifications.” St e p s : •Set speci ...

  • Agilent Technologies 87075C - page 139

    Chapter 9 131 Service Aut o m at e d Per f or ma n ce T ests LD MA TCH XX Measures reflection at p ort XX when th e p ort is switched to the test set’ s TRANSMISSI ON p ort, which is terminat ed with a precision load. T ests the specified per formance of “Load Match, T est Port Selected,” listed in T able 8-2 in Chapter 8, “Specifications.? ...

  • Agilent Technologies 87075C - page 140

    132 Chapter 9 Serv ice Automated Performan c e T e st s INSERT LOSS R->XX and INSERT LOSS T ->XX Measures worst-case ins ertion loss between the test set’ s REFLECTIO N por t or TRANSMISSION po rt and po rt XX when the test set is switched to port XX. T ests the specified perf orm a nc e of “ I nse rti on Los s,” list ed in Ta b l e 8 - ...

  • Agilent Technologies 87075C - page 141

    Chapter 9 133 Service Aut o m at e d Per f or ma n ce T ests XT ALK X X->YY Measu r es crosstalk resu lting from worst- case m ism atch (shorts) between th e s elected ports of the tes t set. T ests the specified performan ce of “Crosstalk,” listed in Ta b l e 8 - 2 in Chapter 8, “Specifications.” St e p s : 3 •Set specified frequen cy ...

  • Agilent Technologies 87075C - page 142

    134 Chapter 9 Serv ice Manual Performance T ests Manual Performance T ests There are no manual Performance V er i fication T ests for this instrument. It is not necessary to man ually perform the Performance V erification T es t s since they are available in an VBA pr ogram that is included with the perf ormance test software. See “Performance V ...

  • Agilent Technologies 87075C - page 143

    Chapter 9 135 Service Adjustments Adjustments There are no adjustments for this instr ument. Any drift in components can be compensated for with the SelfCal feature. Any failure will requ ire the replacement of an assembly . ...

  • Agilent Technologies 87075C - page 144

    136 Chapter 9 Serv ice T roubleshooting T roubles hooting Refer to Chapter 1, “Introducti on and Ins tallatio n ,” to make sure the test set is connected pro perly to the analyzer and that the analyzer has been configur ed for us e with the multipo rt test set. T roubleshooti ng consists of i s olating t he cause of any p roblem to an individua ...

  • Agilent Technologies 87075C - page 145

    Chapter 9 137 Service T roubleshooting If the power supply v o ltage is measured while the cable is disconnected from the main board assembly , the +5 volt supply may not function. It requir es a lo ad of at least 0.5 amps to operate properl y . Th i s can be si mulated w ith any 10 o hm, 5 watt resist or . The LEDs on t he main board as s embly in ...

  • Agilent Technologies 87075C - page 146

    138 Chapter 9 Serv ice Block Diagram Block Diagram Figu re 9-1 Bl ock D iag ram ...

  • Agilent Technologies 87075C - page 147

    Chapter 9 139 Service Parts List Parts Li st This sec tion provides ordering inf ormation and li sts the part nu mbers for the variou s replaceable parts, kits, and accessories for your multiport test set. Ordering Inf o rmation T o order a part listed in the replaceable parts list s : 1. Determine the part nu mber and quantity required. 2. Mail th ...

  • Agilent Technologies 87075C - page 148

    140 Chapter 9 Serv ice Parts List The defective assemb l y must be return ed for credit under the terms of the rebuilt-exchange as sembly pr ogram. Shipping th e Defe ctive Asse mbly Back to Agilent 1. When the rebuilt assembly is received, be careful not to d amage the box in which it was shipped. Y ou will use that box to return the defect ive as ...

  • Agilent Technologies 87075C - page 149

    Chapter 9 141 Service Parts List Major Parts and A ssemblie s Ta b l e 9 - 1 Item # Part Number Qty Description 1 1510-0038 1 Ground co nnector 2 3101-300 8 1 Li ne sw itc h 3 87075 -60014 1 Board assem bly , LED displa y 4 87075 -60018 1 Line module cab le assembly 5 21 10- 0957 1 Fuse H 3.15 A, 250 V AC 6 0950-2023 1 Power su pply assembly 7 8707 ...

  • Agilent Technologies 87075C - page 150

    142 Chapter 9 Serv ice Parts List Figu re 9-2 Major Par t s and A ss embl ies ...

  • Agilent Technologies 87075C - page 151

    Chapter 9 143 Service Parts List Cables, Fr ont Panel, and Main Board Assembly — Option 012 (75 Ω ) Ta b l e 9 - 2 Item # Part Number Qty Description 1 87075-20034 1 Semi-rigid cable, REF LECTION port 2 87075-20035 1 Semi-rigid cable, TRANSMISSION po rt 3 87075-20036 1 Semi-rigid cable, test set POR T 1 4 87075-20037 1 Semi-rigid cable, test se ...

  • Agilent Technologies 87075C - page 152

    144 Chapter 9 Serv ice Parts List Figur e 9-3 Cables , Fr ont Panel, and Mai n Board Assembly— Op tion 012 ...

  • Agilent Technologies 87075C - page 153

    Chapter 9 145 Service Parts List Cables, Fr ont Panel, and Main Board Assembly— Option 006 Ta b l e 9 - 3 Item # Part Number Qty Description 1 87075-20 034 1 Semi-ri gid cable , reflect i on port 2 87075-20 035 1 Semi-ri gid cable, transm i ssion port 3 87075-20 036 1 Semi-ri gid cable, test port 1 4 87075-20 037 1 Semi-ri gid cable, test port 2 ...

  • Agilent Technologies 87075C - page 154

    146 Chapter 9 Serv ice Parts List Figur e 9-4 Cables , Fr ont Panel, and Mai n Board Assembly— Op tion 006 ...

  • Agilent Technologies 87075C - page 155

    Chapter 9 147 Service Parts List Instrument Covers and Associated Parts Ta b l e 9 - 4 Item # Part Number Qty Description 1 5002-396 4 2 Side cover 2 5002-108 8 1 Bottom cover 3 5041-917 1 2 Side trim 4 5041-916 7 4 Feet 5 1460-1345 2 T ilt- up foot wire 6 50 41- 9176 1 T op t rim 7 5002-104 7 1 T op co ver ...

  • Agilent Technologies 87075C - page 156

    148 Chapter 9 Serv ice Parts List Figure 9- 5 In strumen t Covers and Associated Parts ...

  • Agilent Technologies 87075C - page 157

    Chapter 9 149 Service Parts List Accessorie s Ta b l e 9 - 5 Part or Model Number Description 85036B /E T ype -N 75 Ω calibratio n kit 8120-68 18 Parallel port interface cable 1 1. Supplied with yo ur m ul tiport test set. 87075-6 0026 T ype-N front panel interconnect cable (REFL) 1, 2 2. See Ta b l e 1 - 1 for more information on t hese cables. ...

  • Agilent Technologies 87075C - page 158

    150 Chapter 9 Serv ice Parts List ...

  • Agilent Technologies 87075C - page 159

    151 10 Safety and Regulatory Information ...

  • Agilent Technologies 87075C - page 160

    152 Chap ter 1 0 Safety an d Regul atory Inf ormation This section contains required safety and regulatory in formation that is not included elsewhere in this manu al . ...

  • Agilent Technologies 87075C - page 161

    Chapter 10 153 Safety a nd Regul atory In formatio n Safety Inf ormation Safety Inf ormation Much of the required safety information is distributed throughout this manual in appropriate places. Th is section contains all req u ired safety information that is not included elsewhere in this manual. W arnings IMPORT ANT W arning denotes a hazard . It ...

  • Agilent Technologies 87075C - page 162

    154 Chap ter 1 0 Safety an d Regul atory Inf ormation Safety Info rmation Cautions IMPORT ANT Caution deno tes a hazard. It calls attention to a pr ocedure that, if no t correctly perf orme d or adhe red to, wo ul d resu lt in dama ge t o or de str ucti on o f the inst rume nt. Do not proceed beyond a caution sign until the indicated conditions are ...

  • Agilent Technologies 87075C - page 163

    Chapter 10 155 Safety a nd Regul atory In formatio n Safety Inf ormation S tatement of Compliance This instrument ha s been designed and tested in acco rdance with IEC Publication 1010, Safety R equirements for Electronic Measuring Apparatus, and has been supplied in a safe condition. The in str u ction documentation contai ns info rmatio n and war ...

  • Agilent Technologies 87075C - page 164

    156 Chap ter 1 0 Safety an d Regul atory Inf ormation Safety Info rmation Instrument Markings The instruction manual symbol . The product is m ar ked with this symbol when it is necessary for the user to refer to the instructions in the manu al. The CE ma rk sh ows comp liance with European Community . (If accompanied b y a year , it is the y ear w ...

  • Agilent Technologies 87075C - page 165

    Chapter 10 157 Safety a nd Regul atory In formatio n Regulatory Information Regulatory Info rmat io n Notice for Germany: Noise Decl aration Declaration of Conform ity A declaration of co nformity is on file for the PNA models, and a copy is available upon requ est. This is to declare that this instru m ent is in confor mance with the German Regula ...

  • Agilent Technologies 87075C - page 166

    158 Chap ter 1 0 Safety an d Regul atory Inf ormation Regulator y Informatio n ...

  • Agilent Technologies 87075C - page 167

    Index Index Index-1 Numeric s 12 port test set--Option 01 2 , 8 6 port t est set --Option 006 , 8 A accesso ries supplied , 9 activating the test set , 17 adjacent port pai rs , 30 , 37 , 40 Agilen t T echnologi es, contacting , 120 anal yzer comp atibili ty , 11 analyzer configuration for use with test set , 17 Appl ication obje cts , 86 B block d ...

  • Agilent Technologies 87075C - page 168

    Index-2 I ndex Index markin gs, instru ment , 15 6 multiport test s et introductio n , 2 N netw ork analy zer compatibil ity , 11 noise de claration , 157 noninse rtable port pairs , 40 notation C , 42 C? , 34 , 42 O object model , 86 option 0 06 , 8 option 0 12 , 8 P parallel port input connector , 54 parallel port output connector , 54 par t num ...

  • Agilent Technologies 87075C - page 169

    Index Index Index-3 U unpack ing the test se t , 9 V vari able COM object re ference , 89 ventil ation re quirem ents , 16 voltag e requirem ents , 14 W war ra nt y , 118 ...

Produzent Agilent Technologies Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts Agilent Technologies 87075C erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Agilent Technologies
- Bedienungsanleitungen 87075C
- Produktkarten Agilent Technologies
- Informationsbroschüren
- oder Energieetiketten Agilent Technologies 87075C
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Agilent Technologies 87075C.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Agilent Technologies 87075C, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Agilent Technologies 87075C. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Agilent Technologies 87075C ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Agilent Technologies 87075C, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Agilent Technologies 87075C hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Agilent Technologies 87075C verständlich ist.

Eine gänzliche Bedienungsanleitung von Agilent Technologies sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Agilent Technologies 87075C bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Agilent Technologies 87075C befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Agilent Technologies 87075C, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Agilent Technologies 87075C - die uns die ersten Schritte während der Nutzung von Agilent Technologies 87075C erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Agilent Technologies 87075C hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Agilent Technologies 87075C im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Agilent Technologies 87075C?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Agilent Technologies 87075C nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Agilent Technologies 87075C hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)