-
Banner American Easy-Lam II - page 1
...
-
Banner American Easy-Lam II - page 2
TABLE OF CONTENTS Important Safety Messages and Electrical Safeguards……………………3 - 4 Introdu ction………………………………………………………………….5 Specifica tions………………………………………………………………..5 Initial Setup………………………………………………? ...
-
Banner American Easy-Lam II - page 3
3 IMPORTANT SAFETY MESSAGES AND ELECTRICAL SAFEGUARDS For your protection, do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient locati on for future reference. This instruction manual and labels affixed to the laminator are important safe ...
-
Banner American Easy-Lam II - page 4
4 plug into an outlet, contact a qualified electrician to have a suitable outlet installed. Ø Do not leave the laminator power on overnight. Unplug the laminator at the end of the day. Ø Unplug the laminator befo re moving it or when it is not in use for an extended period of time as a precaution against the possibility of an internal malfunction ...
-
Banner American Easy-Lam II - page 5
5 INTRODUCTION Congratulations on your purchase of the Easy - Lam II Roll Laminator . This unit is designed to provide years of trouble - free service. The Easy - Lam II will accept rolls of laminating film up to 27” wide in both 1.5 and 3 mil thicknesses. Paper and card stock up to 1/16” (1.6mm) thick may be laminated without adjusting th e fe ...
-
Banner American Easy-Lam II - page 6
6 INITIAL SETUP Unpacking Before unpacking the unit, inspect the shipping container for signs of damage. Notify the carrier and your dealer immediately if any damage is noted. CAUTION! The laminator weighs approximately 91 lbs. Use two people when removing the laminator from the shipping container. NOTE! We recommend saving the packaging in case yo ...
-
Banner American Easy-Lam II - page 7
7 Figure 1 ...
-
Banner American Easy-Lam II - page 8
8 Heater Switch This swi tch turns power on and off to the top and bottom h ea t s hoe. (Switch will light up i n the “on” position ) . Heat Indicator Light This light goes on when the heat s witch is first turned on and then remains on until the heat s hoe reaches the operating temper ature. After that point, the light will go on and off perio ...
-
Banner American Easy-Lam II - page 9
9 Figure 2 a Threading Laminating Film These instructions apply to poly - in film rolls (shiny side out, dull side in). 1. For the top supply roll, place the mandrel ends into the slots on the top of the laminator. If you are facing the front of the laminator, the film should unwind toward you from the bottom of the ro ll as in Figure 3. ...
-
Banner American Easy-Lam II - page 10
10 Figure 3 2. Pull 6” - 12” of film from the top roll. Pass the film under the idler bar and safety shield, and over the heat s hoes. Make sure the shiny side of the film is against the shoes. See Figure 5 and 6. 3. Fo r the bottom supply roll, remove the feed table. Place the mandrel ends into position in the lower mandrel holder slots. If yo ...
-
Banner American Easy-Lam II - page 11
11 running the machine. I f the idler bar is not in the upper position, you will not be able to properly adjust roll film tension . Drape the film from the bottom roll over the film from the top roll. (Use a piece of tape to hold film in place). See Figure 5 and 6. NOTE: The s hiny side of the f ilm must always go against the heat s hoes. CAUTION! ...
-
Banner American Easy-Lam II - page 12
12 5. Turn the motor s witch to the “on” posi tion to start the r ollers. 6. Push a piece of thin letter - sized cardboard against the film so that it is centered between the two heat s hoes. Push t he cardboard and film into the nip r ollers. See Figure 5. 7. When the feed card has completely exited the Pull Rollers at the r ear of the laminat ...
-
Banner American Easy-Lam II - page 13
13 counterclockwise to decrease) until the film passes over the top heat s hoe without wr inkles and the w eb between the laminating and pull r ollers is tight. Note: This adjustment should require only a slight turn. If increased too much , you may stall the drive motor. Figure 7 5. If necessary, locate the knob on the right si de of the bottom su ...
-
Banner American Easy-Lam II - page 14
14 3. Tur n the knob clockwise to increase and counterclockwise to decrease the temperature. If reducing the temperature, wait several minutes for the heat to drop to the desired operating temperature. When increasing temperature, the indicator lamp will come on a s the laminator is heating up and go off when it reaches the set temperature. (Wait 1 ...
-
Banner American Easy-Lam II - page 15
15 NOTE: You may want to run a test lamination first, as any item that passes between the heat s hoes will be laminated and cannot be recovered until it exits the rear of the laminator. 7 . Additional items may be fed in sequence, keeping enough distance between sheets for trimming. 8 . Afte r the last item has exited the pull rollers, turn the mot ...
-
Banner American Easy-Lam II - page 16
16 ACTION: Check the thickness of item to be laminated. Maximum thickness is 1/16” (1.6mm). Clean heat shoes of residual adhesive. Refer to the MAINTENANCE section for cleaning instructions. PROBLEM: Plastic is not bonding to the item or to itself at the edges. ACTION: Make sure heat s hoes and rollers are at the proper operating temperature and ...
-
Banner American Easy-Lam II - page 17
17 Maintenance This section contains instructions for cleaning and maintaining your laminator. These procedures should be performed at regular intervals to help ensure the trouble - free opera tion of your laminator. Cleaning the Heat Shoes and Laminator Rollers The Heat Shoes and Laminating Rollers should be cleaned of any residual adhesive whenev ...
-
Banner American Easy-Lam II - page 18
18 Removing Wrap - arounds When laminating with thinner gauges of films, there is the possibility of the film wrapping around the Pull Rollers. Refer to Cleaning the Heat Shoes and Laminating Rollers in order to remove a wrap - around. If the film cannot be pulled out of the back of the machine, leave the motor switch on and use the reverse switch ...
-
Banner American Easy-Lam II - page 19
19 PARTS LIST AND ILLUSTRATIONS This section contains reference drawings and parts list to assist you when ordering parts for your laminator. The drawings show only those parts tha t may be replaced by the dealer. Item Part N o. Description Quantity 1 10091 C - CLIP, 15/16” DIA 4 2 10092 BUSHING, 5/8 x ¾ x 1 ¼ 8 3 10093 KNOB, ¼ - 20 x 1 ¼ LON ...
-
Banner American Easy-Lam II - page 20
20 Item Part No. Description Quantity 37 1182 FUSE, 15AMP, MDA - 15 1 38 1242 HEATER, TUBULAR, EASY - LAM II 4 39 10415 RELAY, SOLID STATE, 25 AMP 1 40 10358 SPROCKET, MOTOR, EASY - LAM II 1 41 2801 SPROCKET, 22T, STEEL 1 42 10371 SPROCKET, 25B21, .625 BORE 1 44 10232 SWITCH, MOTOR REVERSE, 1 EASY - LAM II 45 10282 COVER, SID E, LEFT, EASY - LAM II ...
-
Banner American Easy-Lam II - page 21
21 ...
-
Banner American Easy-Lam II - page 22
22 ...
-
Banner American Easy-Lam II - page 23
23 ...
-
Banner American Easy-Lam II - page 24
24 ...
Haben Sie eine Frage bezüglich Banner American Easy-Lam II?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Banner American Easy-Lam II nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Banner American Easy-Lam II hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.