Deutsch dropdown-ico

Bedienungsanleitung Husqvarna 318

36 Seiten 4.34 mb
Download

Zur Seite of 36

Summary
  • Husqvarna 318 - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 318 Rider 320 A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...

  • Husqvarna 318 - page 2

    2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ................................................... 3 INTR ODUCTION Dear Customer , ..................... ...

  • Husqvarna 318 - page 3

    English – 3 Ser vice journal Pre-deliver y service 1 Charge the batter y f or 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure (60 Kpa, 0.6 bar , 9 PSI). 4 Adjust cutting unit: Adjust lift springs (effectiv e weight of cutting unit should be 12-15kg / 26.5-33 lb). Adjust cutting unit s ...

  • Husqvarna 318 - page 4

    4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented ar ticulated steering. Riders are designed f or maximum efficiency e ven in small or confined areas . The closely grouped co ntrols and pedal-operated h ydrostatic ...

  • Husqvarna 318 - page 5

    English – 5 KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alw a ys wear: • Approv ed he ...

  • Husqvarna 318 - page 6

    6 – English KEY T O SYMBOLS Star ting instructions Switch off the engine and take off the ignition cable bef ore repairs or maintenance Check the engine’ s oil le vel Check tr ansmission oil lev el Lift up the cutting unit Apply the par king brak e. If the engine is cold, use the chok e Release the par king brak e before driving ...

  • Husqvarna 318 - page 7

    English – 7 WHA T IS WHA T? Location of the controls 12 3 4 6 8 7 9 12 14 13 15 10 11 5 1 Speed limiter f or driving forward 2 Speed limiter f or rev ersing 3 Lifting le ver f or the cutting unit 4 Cutting height adjustment le ver 5 Ignition lock 6 Throttle control/choke control 7 Counter 8 Cov er lock 9 P arking brake 10 Lock b utton f or parkin ...

  • Husqvarna 318 - page 8

    8 – English SAFETY INSTR UCTIONS Safety instructions These instructions are for y our saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider. • Contact your insur ance company . • Y ou should hav e fully comprehensive insurance including: third par ty , fire, damage, theft and liability Gen ...

  • Husqvarna 318 - page 9

    English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment. • Ne ver w ear loose fitting clothes that can catch in moving par ts. • Ne ver use the ...

  • Husqvarna 318 - page 10

    10 – English SAFETY INSTR UCTIONS • F ollow the manuf acturer’ s recommendations regarding wheel weights or counterbalance weights to increase machine stability . Children • Serious accidents may occur if y ou f ail to be on your guard f or children in the vicinity of the machine. Children are often attracted to the machine and mowing. Nev ...

  • Husqvarna 318 - page 11

    English – 11 SAFETY INSTR UCTIONS • Do not change the setting of gov ernors. If you run too fast, you risk damaging the machine components. See chapter on T echnical data f or highest per mitted engine speed. • Ne ver use the machine indoors or in spaces lac king proper ventilation. Exhaust fumes contain carbon mono xide, an odourless, poison ...

  • Husqvarna 318 - page 12

    12 – English PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 318 and Rider 320 A WD . Rider 320 A WD is equipped with all wheel dr ive . The power tr ansmission from the engine is handled by a h ydrostatic t ...

  • Husqvarna 318 - page 13

    English – 13 PRESENT A TION Seat The seat has a jointed attachment on the front edge and can be tipped f orward. The seat can also be adjusted lengthwa ys. Loosen the handles under the seat and adjust it f orwards or backw ards to the desired position. Fueling The engine runs on unleaded petrol with a minimum octane rating of 85 (not mix ed with ...

  • Husqvarna 318 - page 14

    14 – English Driving Bef ore star ting • Read the saf ety instructions and information concer ning the placement of controls and functions bef ore star ting. • P erform daily maintenance before starting as set out in the Maintenance schedule. Star t the engine 1 Make sure that the clutch control is depressed. Rider 320 A WD has one control fo ...

  • Husqvarna 318 - page 15

    English – 15 Driving Connecting the jump leads • Connect each end of the red cable to the POSITIVE pole (+) on each batter y , e xercise care not to short circuit any of the ends against the chassis. • Connect one end of the blac k cable to the NEGA TIVE pole (-) on the fully charged batter y . • Connect the other end of the blac k cable to ...

  • Husqvarna 318 - page 16

    16 – English Driving Cutting tips • Localise and mark stones and other fixed objects to a void collision. • Star t with a high cutting height and reduce down until the required mowing results are obtained. • The mowing result will be best with the highest permitted engine speed, see technical data, (the blades rotate rapidly) and low speed ...

  • Husqvarna 318 - page 17

    English – 17 Maintenance Maintenance schedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) First change after 8 hours. When oper ating with a heavy load or at high ambient temperatures , replace e very 50 hours. 2) Mai ...

  • Husqvarna 318 - page 18

    18 – English Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure. Do not direct the jet tow ards electrical components or bearings. Do not rinse hot surfaces suc ...

  • Husqvarna 318 - page 19

    English – 19 Maintenance • If necessar y , the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar . Do not ov er tighten the cables; they should only be drawn in tow ards the steering collar . Hold the cable , f or example using an adjustab le wrench, so that it does not twist. If the adjustment is only ma ...

  • Husqvarna 318 - page 20

    20 – English Maintenance Replacement of fuel filter Replace the fuel filter e very 100 running hours (once per season) or more frequently if it is clogged. Replace the filter as f ollows: 1 Open the engine cov er . 2 Mov e the hose clips aw a y from the filter . Use a pair of flat pliers. 3 Pull off the filter from the hose ends. 4 Press th ...

  • Husqvarna 318 - page 21

    English – 21 Maintenance Ignition system The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. F or recommended spark plug, see T echnical data. Replacing the spark plug 1 Remov e the ignition cable shoe and clean around the spark plug. 2 Remov e the spark plug with a 3/4” (19 mm) spark plug sock e ...

  • Husqvarna 318 - page 22

    22 – English Maintenance Checking the engine’ s cooling air intake Clean the air intake g rille in the engine cover behind the driver’ s seat. Open the engine cov er . Check that the cooling intak e is free from leav es, grass and dir t. Check the air duct, located on the inside of the engine co ver , ensure it is clean and does not rub again ...

  • Husqvarna 318 - page 23

    English – 23 Maintenance 9 Hook up the height adjustment strut. 10 Secure the collet spring. 11 Fit the front cov er . Removing the cutting unit 1 Carr y out points 1-6 to put the cutting unit in the ser vice position, see Ser vice position f or the cutting unit. 2 Lower the cutting unit. 3 Open the unit catch. 4 Pull out the cutting unit. Checki ...

  • Husqvarna 318 - page 24

    24 – English Maintenance Checking the cutting unit’ s parallelism Check the cutting unit’ s parallelism as f ollows: 1 Check the air pressure in the tyres 60 kP a/0.6 kp/cm 2 /8.5 PSI. 2 Place the machine on a flat surf ace. 3 Put the lifting le ver in the mo wing position. 4 Measure the distance between the ground and the front and rear edg ...

  • Husqvarna 318 - page 25

    English – 25 Maintenance 7 Remov e the screws on the cutting co v er . Lift the unit frame and remov e the cutting unit cover . 8 Loosen the spring that tensions the V -belt and pr y off the belt. 9 Simply re verse the procedure to fit the ne w belt. Service position for the cutting unit The cutting head can be placed in the service position to ...

  • Husqvarna 318 - page 26

    26 – English Maintenance Restoring fr om service position 1 Grip the front edge of the unit and loosen the lock, f old down and slide in the unit. 2 Replace the cutting height sta y and the belt. 3 T ension the belt with the belt adjuster . 4 Fit the front cov er . Checking the b lades W ARNING! W ear gloves to protect y our hands when working wi ...

  • Husqvarna 318 - page 27

    English – 27 Lubrication Checking the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again. The dipstick should be completely scre wed down Pull the dipstick out again and re ...

  • Husqvarna 318 - page 28

    28 – English Lubrication Checking the transmission oil le vel 1 Remov e the transmission co ver . Undo the two screws (one on each side) and lift off the transmission cov er . 2 Check that there is oil in the tr ansmission’ s oil tank. Rider 318 Fill if necessary with engine oil SAE 10W/40 (class SF–CC). Rider 320 A WD Fill if necessary with ...

  • Husqvarna 318 - page 29

    English – 29 T roub leshooting sc hedule Prob lem Procedure Engine does not start There is no fuel in the fuel tank Spark plug defectiv e F aulty spar k plug connections or interchanged cables Dir t in the carburettor or fuel line Star ter motor does not tur n ov er the engine Starter motor does not turn over the engine Batter y flat Bad contact ...

  • Husqvarna 318 - page 30

    30 – English Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine. Fuel stabilise ...

  • Husqvarna 318 - page 31

    English – 31 TECHNICAL D A T A Note 1: The power r ating of the engine indicated is the av erage net output (at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ from this v alue. Actual power output f or the engine installed on the final machine will de ...

  • Husqvarna 318 - page 32

    32 – English TECHNICAL D A T A Cutting unit Combi 94 Combi 103 Combi 112 Cutting width, mm/inch 940/37 1030 / 41 1120 / 44.1 Cutting heights, 7 positions , mm/inch 25-75/0.98-2.95 25-75/0.98-2.95 25-75/0.98-2.95 Blade length, mm/inch 358/14.09 388/15.28 420 / 16,5 IMPOR T ANT INFORMA TION When the ser vice lif e of this product has been ser ved a ...

  • Husqvarna 318 - page 33

    English – 33 TECHNICAL D A T A EC-declaration of conf ormity (Applies to Europe onl y) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqv ar na Rider 318 and Rider 320 A WD from 2010’ s serial numbers and onwards (the year is clearly stated in plain te xt on the rating plate with subsequent serial numbe ...

  • Husqvarna 318 - page 34

    ...

  • Husqvarna 318 - page 35

    ...

  • Husqvarna 318 - page 36

    ´®z+VVr¶6(¨ 2011-11-16 ´®z+VVr¶6(¨ 1154548-26 Original instructions ...

Produzent Husqvarna Kategorie Lawn Mower

Dokumente, die wir vom Produzenten des Geräts Husqvarna 318 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Husqvarna
- Bedienungsanleitungen 318
- Produktkarten Husqvarna
- Informationsbroschüren
- oder Energieetiketten Husqvarna 318
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Husqvarna 318.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Husqvarna 318, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Husqvarna 318. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Husqvarna 318 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Husqvarna 318, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Husqvarna 318 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Husqvarna 318 verständlich ist.

Eine gänzliche Bedienungsanleitung von Husqvarna sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Husqvarna 318 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Husqvarna 318 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Husqvarna 318, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Husqvarna 318 - die uns die ersten Schritte während der Nutzung von Husqvarna 318 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Husqvarna 318 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Husqvarna 318 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Husqvarna 318?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Husqvarna 318 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Husqvarna 318 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)