-
Belling BE814 - page 1
BE814 Fully Integrated Freezer INST ALLA TION AND USER INSTRUCTIONS Y ou must read these instructions prior to using the appliance and retain them for future reference. ...
-
Belling BE814 - page 2
...
-
Belling BE814 - page 3
Contents Introduction & safety warnings ...........................................................................2 Electrical requirements ......................................................................................3 T ransportation instructions ................................................................................. 4 Inst ...
-
Belling BE814 - page 4
Congratulations on your choice of a Belling quality Appliance which has been designed to give you service for many years. W ARNING ! IMPORT ANT ! DO NOT connect your appliance to the electricity supply until all packing and transit protectors have been removed. • Leave to stand for at least 4 hours before switching on to allow compressor oil to s ...
-
Belling BE814 - page 5
3 ELECTRICAL REQUIREMENTS Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating plate inside the appliance corresponds to your electricity supply . Rating label is on the left hand side of freezer inner liner . We recommend that this appliance is connected to the mains supply via a suitable ...
-
Belling BE814 - page 6
TRANSPORT A TION INSTRUCTIONS 1. The appliance should be transported only in a vertical upright position. The packing as supplied must be intact during transportation. 2. If during the course of transport the appliance has to be transported horizontally , it must only be laid on its left hand side when standing in the front of the appliance. After ...
-
Belling BE814 - page 7
1. T o avoid a hazard due to instability of the appliance, it must be fixed in accordance with the instructions. 2. Do not operate this appliance unless installed to furniture. 3. The appliance should be located on a smooth surface. The four front and back feet can be adjusted as required. T o ensure that, your appliance is standing upright adjust ...
-
Belling BE814 - page 8
6 REPOSITIONING THE DOOR Follow the step by step instructions and the diagram below . Numbers in brackets refer to diagrams. 1 2 1 2 4 3 8 7 5 6 8 7 ...
-
Belling BE814 - page 9
7 1. Switch off at the socket outlet and pull out the mains plug. 2. Remove all food, loose items and fittings from inside the appliance and door shelves. 3. Unscrew the bolts and remove the upper and bottom hinges from the cabinet and door . (1) (2) 4. Remove stoppers. (3) (4) 5. Fit the stoppers on the opposite side. (5) (6) 6. Reposition the upp ...
-
Belling BE814 - page 10
ST ARTING Final Check Before you start using the freezer check that: 1. The feet have been adjusted and the product is level. 2. The interior is dry and air can circulate freely at the rear . 3. Clean the interior as recommended under "CLEANING AND CARE." 4. Insert the plug into the wall socket and switch on the electricity supply . A voi ...
-
Belling BE814 - page 11
9 STORING FROZEN FOOD Prepacked commercially frozen food should be stored in accordance with the frozen food manufacturer's instructions for a frozen food storage compartment. The freezing area is marked with symbol on the door liner . T o ensure that the high quality achieved by the frozen food manufacturer and the food retailer is maintained ...
-
Belling BE814 - page 12
FREEZING FRESH FOOD Freezing capacity of your appliance in a 24 hours period is 10 kg (22.1 lb). Never exceed this maximum capacity . Fast freeze compartment (3) is shown in diagram. T ake special care not to mix already frozen food and fresh food. If the fast freeze compartment (3) is filled with fresh food, other compartments can also be used to ...
-
Belling BE814 - page 13
1 1 DEFROSTING Defrost twice a year or when a frost layer of around 7 mm (1/4") has formed. T o start defrosting procedure turn the thermostat knob to zero position (Alternatively you may switch off the freezer at the socket outlet and pull out the mains plug.) All food should be wrapped in several layers of newspaper and stored in a cool plac ...
-
Belling BE814 - page 14
12 CLEANING AND CARE ** We recommend that you switch of f the freezer at the socket outlet and pull out the mains plug before cleaning. ** Never use any sharp abrasive instrument, soap, household cleaner , detergent and wax polish for cleaning. ** Use luke warm water to clean the cabinet of the freezer and wipe it dry . ** Use a damp cloth wrung ou ...
-
Belling BE814 - page 15
13 DO'S AND DON'TS Do- Check contents of the freezer at regular intervals. Do- Clean and defrost your freezer regularly (See "Defrosting") Do- Keep food for as short a time as possible and adhere to "Best Before", "Use By" dates. Do- Store commercially frozen food in accordance with the instructions given on ...
-
Belling BE814 - page 16
14 INST ALLA TION INSTRUCTIONS - DET AILED STEP BY STEP NOTE 1) Height of the product can be adjusted by the help of adjustable feet (front and back) to fit the furniture niche height (B). 2) Do not operate this appliance until it has been installed in the furniture. A (mm) 813 - 863 mm B (mm) 820 - 870 mm C (mm) 100 - 150 mm A 545 595 598 ...
-
Belling BE814 - page 17
15 min.550 B min. 600 min.550 C C 600 D > 150 mm. C D C=100-150 mm ...
-
Belling BE814 - page 18
16 2 7 1 3 4 5 6 3 4 5 6 ...
-
Belling BE814 - page 19
17 Note: 1. These dimensions are valid for products,which are hinged on right hand side. 2. When door opening direction is reversed, mirror image of this instruction should be considered. That is, dimensions should be considered for opposite sides. B E E = 1,5 mm is recommended. T op view Front view E B = 25 mm minimum. 320 B 9 8 20 20 = = ...
-
Belling BE814 - page 20
18 10 11 12 13 14 ...
-
Belling BE814 - page 21
19 15 ...
-
Belling BE814 - page 22
20 GUARANTEE DET AILS Y our new Belling product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase. What is covered? • Repairs necessary as a result of faulty materials, defective components or manufacturing defect. • The cost of functional replacement parts, but excluding consumable ite ...
-
Belling BE814 - page 23
21 Recycling This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European Directive 2002/96/EC in order to be recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional auth ...
-
Belling BE814 - page 24
PERFORMANCE Energy efficiency class Energy consumption - Kwh/year Net storage - vol fresh food ltrs (cu.ft.) Net storage - vol frozen food ltrs (cu.ft) T otal net vol - ltrs (cu.ft.) Frozen food compartment rating Conservation time from failure Freezing capacity fresh food - kg /24 hrs. Climate class Operating noise level dB(A) A 205 ----- 87 (3.1) ...
-
Belling BE814 - page 25
23 WIRING DIAGRAM ...
-
Belling BE814 - page 26
...
-
Belling BE814 - page 27
...
-
Belling BE814 - page 28
In case of dif ficulty within the UK, please call Belling Customer Care Centre Helpline on 08 44 815 3746 When you dial this number you will hear a recorde d message and be given a number of options. This indicates that your call has been accepte d and is being held in a queue. Calls are answered in strict rotation as our Cust omer Care Representat ...
Haben Sie eine Frage bezüglich Belling BE814?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Belling BE814 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Belling BE814 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.